Search Documents

By B. R. Bowerman, W. J. Thoburn, M. J. Humphris

"Nickel granules are produced for carbonylation by pouring a molten stream into a path of high pressure water. Granules and water are separated in dewatering bins. The overflow, which contains up to 0.1 weight percent solids, was initially cooled and recycled to the granulating step. However, the rate of buildup of these solids in the handling system was intolerable. A lamella thickener was installed to solve the problem by removing solids from the dewatering bin overflow. Its description, application and performance to date are discussed.The lamella thickener treats a slurry containing about 0.1% solids of which about 30 weight percent is less than 325 mesh. It recovers 80 to 90 percent of the input solids in an underflow slurry containing 90 weight percent solids. Since its installation the frequency of cleanout of the recycle water handling system has dropped from about once per month to about once or twice per-year."

Jan 1, 1977

By Greg Gosson

These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own counsel in relation to any decision or course of action contemplated. Outline ??What is meant by a ?current technical report? under NI 43-101? ??When is a current technical report required? ??Who makes the decision regarding whether a technical report is current? ??Examples of the types of information that make a technical report no longer current for securities filing purposes.

May 1, 2009

Proper water and thermal management is essential for obtaining high performance of Proton Exchange Membrane Fuel Cells (PEMFCs). A steady, two-dimensional water and thermal management model was developed, aiming at considering pressure drop, open circuit voltage variation with stack temperature, water vapor effects on membrane conductivity, which made the model physically more reasonable and more suitable for various operating conditions. The model could predict the distributions of a series of important parameters along the flow channel, and thus the effects of various operating and design parameters on the fuel cell performance could be investigated easily by numerical trial-and-error method. The modeling results compared well with the available experimental results from the literatures. The results also showed that the humidification is crucial for the performance of PEMFCs. The model could be a very useful engineering tool for the optimization of PEMFCs.

Jan 1, 2005

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By J. R. Meyer, P. L. Dean

"The Department of Mines and Energy is at present investigating the dimension-stone potential of the Nain anorthosite complex. These rocks are known to host occurrences of labradorite, a semiprecious gemstone known for its beautiful play of colours (chatoyance). Test blocks that contain 5% to 18% chatoyant labradorite were extracted from three prospects south of Nain. These have been slabbed and polished for further evaluation.Second-grade labradorite stockpiled around the Grenfell quarry on Tabor Island is also being evaluated as a potential source of aggregate for use in terrazzo tiles, precast concrete and epoxy-backed wall panels.IntroductionThe Nain anorthosite complex consists of approximately 10000 km2 of anorthosite and related basic rocks , which are well exposed along the coast of Northern Labrador (Fig. 1) (Emslie et al., 1972). These rocks have been known for centuries to host deposits of gem-quality labradorite. The chatoyant nature (i.e. the play of colours or labradorescence) of this semiprecious feldspar has been utilized mostly in the making of jewelry and other polished, handcrafted products. In the early sixties, Brinex Limited (now Brinco Limited) attempted larger scale commercial exploitation of labradorite, including use 'as building stone and in polished precast concrete for facings on buildings' (Brummer, 1984). After six years of work, which included market studies, Brinex decided that, at that time, the demand did not warrant further production.In recent years, there has been a dramatic increase in the markets for dimension-stone. In the period from 1980 to 1985, the demand in the United States for granite, much of which is imported, has increased 1735070 (Marble Institute of America, 1986). The dimension-stone industry's remarkable growth rate has, in part, resulted from new technology that makes it easier and faster to quarry and cut stone. This has allowed natural storie to compete with other building materials. Now, it is not only used for exterior cladding and walkways, but also on interior walls and floors, and in home and office furnishings, such as countertops for kitchens and bathrooms, table and desk tops, stairways, window sills, and fireplaces."

Jan 1, 1988

By A. Taylor

This paper considers mineral processing in zero gravity dry environments typical of asteroids or comets. The electro-dynamic separation technique using pneumatic flow systems is explored. Pneumatic delivery of solids is used because of extreme temperature changes and the possible scarcity of water. The present earth-based process and how it can be modified for these conditions is examined.

May 1, 2001

By F. G. Smith

Abstract Laboratory methods are now in use whereby the temperature and pressure during the crystallization of hydrothermal minerals can be determined. The techniques include the use of the decrepitation method of studying liquid inclusions, and electrical measurements of pyrite. The determinations are sufficiently accurate that the data can be used in solving a variety of ore deposition problems. Within the last year, several new laboratory techniques have been developed in the Geochemical Laboratory of the Department of Geological Sciences, University of Toronto. The results of several tests of ore by these methods have proved to be useful in treating some problems which previously were considered unsolvable. It is now possible to determine the temperature of deposition of most of the minerals in a hydrothermal ore deposit, also the depth below the surface during deposition. Measurements can also be made of the reopening history of a complex ore. The temperature-pressure determinations depend upon the fact that minerals deposited from a hydrothermal solution always trap a small amount of the solution at the time of crystallization. The solution, being predominantly composed of water, has a density which depends upon the temperature and the pressure prevailing during crystallization. After ore deposition is complete, erosion and isostatic uplift finally exhumes the vein. During this slow fall in temperature and pressure, the solution contracts and a gas bubble appears. If the trapped solution in the mineral is examined, the gas-liquid ratio records the density of the solution at the time the mineral was deposited (except for a slight change in the volume of the mineral). The thermal expansion and compressibility of water and water solutions are known to a sufficient degree that, if the gas /liquid ratio can be determined, the temperature-pressure relations during deposition can be calculated.

Jan 1, 1949

By V. ?. Chanturiya, I. Zh. Bunin, M. V. Ryazantseva

"Surface changes in naturally occurring metal sulfides (pyrite, arsenopyrite, sphalerite, chalcopyrite, galena, and molybdenite) due to treatments from high-power electromagnetic pulses (HPEMP) at varying times were studied using X-ray photoelectron spectroscopy. Analysis of the obtained results revealed common patterns and differences in surface transformations. The transformations were found to include two main stages. The first stage was observed at low treatment intensities (up to n ~103 pulses). At this stage, formation and accumulation in the surface layer of the nonstoichiometric sulfide phase, oxides and hydroxides, as well as elemental (polysulfide) sulfur and/or metastable sulfur species (thiosulfate, sulfite) was observed. The second stage (N = 3·103 pulses) is characterized by thermal removal of sulfur species and renewal of the mineral surface (sulfidization).It was found that the chemical changes of the sulfur on the surface layer of pyrite, arsenopyrite, chalcopyrite included accumulation/formation of S0 (Sn 2-) at the first stage of the transformation, followed by its removal. An increase in the surface concentration of elemental sulfur for pyrite and chalcopyrite was 10–12% while arsenopyrite was approximately 5%. A more complicated chemical change was observed for sphalerite and galena, that included formation/accumulation of metastable sulfur species (thiosulfate, sulfate) at the initial stage (up to 103 pulses) and during longer treatment times, the sulphur is reduced back to its initial state (sulfide or disulfide). The increased concentration of S0 sulfur, compared to the original sample, was only 3% in galena and sphalerite.The application of HPEMP treatment to improve flotation selectivity is supported by singlemineral flotation tests. Changes in flotability as a result of HPEMP treatment are principally explained by surface phase changes that resulted in higher adsorption activity."

Jan 1, 2016

By R. Salimi

Tricalcium aluminate hexahydrate (TCA) is used as filter-aid for security filtration in the Bayer alumina process. TCA is typically produced on-site by mixing Bayer liquor with slaked lime. Specific properties are required from the TCA to ensure adequate filter throughput, lifetime and importantly effective reduction of solid/colloidal impurities from the solution. The effect of reaction time on morphology and particle size distribution of tricalcium aluminate was studied for a batch experiment at simulated process conditions. It was found that reaction time plays a critical role on the morphology, crystal structure (diameter and crystallinity) and particle size distribution. In the early stages of the reaction, nucleation dominates the crystallization process followed by growth dominated by agglomeration up to a mean particle size of 10 µm. The particle morphology shifted from an irregular shape to more spherical throughout the course of the reaction.

Jan 1, 2014

By L. G. Morrell

Introduction A Self-Dumping cage which combines the features of a small skip and a cage has been used in a vertical winze between the 2,000 and 2,500 levels at the Coniaurum mine for the past three years, during which time its success has been demonstrated by uninterrupted service and low maintenance charges. lt was designed by John Reddington, mine manager, and was built under his supervision in the Coniaurum mine shops. Being new in many of its operating features, a small-scale model was made and tried before the final construction was undertaken. The mechanical performance of the model suggested a few minor changes that were incorporated in the final drawings. During its three years of use, the automatic dumping device has saved the expense of deck-handling of the cars. This actually represents a gross economy of something over four times the cost of construction and installation, which totalled $1,325. The cage, empty, weighs 2,200 pounds, of which 500 pounds represents the weight of the dumping accessory and necessarily heavier construction. Besides a considerable financial saving, the time saved in unloading increases the daily hoisting capacity of the winze. In raising ore from the 2,500 level, five minutes are required for a complete trip. Allowing one minute for the alternative of decking, we believe that the automatic dumping has increased the capacity of the winze hoist nearly 20 percent.

Jan 1, 1933

By T. S. Li, D. Ilievski, I. Livk

Micromixing of the fluid and the particulate phases in a continuous gibbsite precipitator was investigated for three different micromixing states, namely maximum mixedness (MM), complete segregation (CS), and maximum mixedness of the fluid but complete segregation of the particulates (MMF-CSP). The influence of the micromixing on continuous precipitation of gibbsite was studied at different precipitation conditions via simulation. Three different cases were considered with respect to the precipitation kinetics: (1) gibbsite secondary nucleation is favoured with slow crystal growth and agglomeration rates; (2) gibbsite crystal agglomeration and growth are dominant mechanisms with secondary nucleation suppressed; and (3) gibbsite crystal growth is the only relevant phenomenon. Simulation results for the cases (1) and (3) showed that the crystalline products for both the MM and MMF-CSP micromixing states were very similar, but the product obtained from the CS micromixing state was considerably different. This indicates that at those precipitation conditions the fluid micomixing has the dominant effect on the product properties, and the particulates micromixing effect is insignificant. However, when operated under the conditions of fast crystal growth and agglomeration kinetics, i.e. case (2), both the fluid and the particulates micromixing were found to affect the precipitation process, resulting in a significantly different product. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists ofCIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By J. Q. Chen

The elastic-plastic behavior and the fracture mechanisms of two 2198 Al-Cu-Li thin sheets are investigated. The first material (2 mm thick) is in a recrystallized state after cold rolling. The second material (6 mm thick) is hot rolled and has a fibrous grain structure. The two materials are studied in both T351 and T851 conditions. Tensile tests are carried out along different sheet directions using flat and notched specimens. Fracture resistance was characterized using Kahn tear specimens and M(T) panels. Macroscopic fracture surface of smooth tensile specimens depends not only on testing material but also on the loading direction. For Kahn tear specimens, fracture is initiated in a small flat triangle whereas slant fracture is observed during crack propagation. Fracture mechanisms were investigated using scanning electron microscopy (SEM) and X-ray 3D tomography.

Jan 1, 2011

The 2-4D window shown above is the base startup window which allows you to begin a new project. ??Setting up the project is the first step ??The next step is to setup the properties to be used in this project

Feb 1, 2008

By Y. Jiang, B. Li, R. Liu

"In this study, laboratory flow tests were conducted on 2-D artificial rock fracture network models containing a single intersection constituted by two inlet and two outlet branches. Three models with different intersecting angles of 60°, 90° and 120° were tested using both dye solution and distilled water. Constant flow rates were imposed on one inlet, and the flow patterns in the fracture intersections were captured by using a CCD camera. The test results were compared with the predictions made by numerical simulations that solved the Navier-Stokes equations. The results revealed that when Reynolds number (Re) is as low as less than 1, the intersecting angle has negligible influence on the flow rate of each branch and the flow patterns within a fracture intersection. As the interesting angle ? and Re (e.g., from 10 to 200) change, the normalized flow rates of different outlet branches change significantly, due to the inertial effect of fluid flow. These changes could be represented by a series of mathematical expressions involving Re and ?, which could be applied to fracture network models to improve their prediction accuracy on hydraulic properties (e.g., permeability and breakthrough curves of particles) of rock masses. INTRODUCTIONCoupled stress, flow, heat and mass transport are the corner stone subjects for many geoscience and geo-engineering disciplines, such as geological disposal of radioactive waste and geothermal energy exploitation. Many outstanding issues need to be investigated to enhance the knowledge on these subjects, and specifically more in-depth research in testing and modeling of the fluid flow in fractured rock masses is needed. In recent years, discrete fracture network (DFN) models have been extensively used to study the fluid flow and mass transport behaviors of fractured rock masses (e.g., Min et al., 2004; Zhao et al., 2011). In these models, each fracture is usually represented by a parallel-plate model, in which fluid flow exactly follows the cubic law. Therefore, comparative flow rate in each outlet branch of an intersection in these models only depends on its aperture. In reality, due to the surface roughness of fractures, the magnitude of mechanical aperture is usually larger than that of the hydraulic aperture of each fracture (Li et al., 2008; Xiong et al., 2011), and abundant flow patterns could exist in an intersection, influenced by its geometry, varying with changing Reynolds number (Re) (Kosakoswski & Berkowitz, 1999). Recent studies have also revealed that different mixing patterns might exist at a fracture intersection, bounded between streamline routing model and complete mixing model, that determine the final distribution of solutes in fractured rock masses (Johnson and Brown, 2001; Park et al., 2001). Numerical simulation has been the principal method adopted in previous studies, and the studies conducting flow tests on intersected fractures are less reported (Wilson & Witherspoon, 1976; Johnson and Brown, 2001). In this study, laboratory flow tests and numerical simulations by solving the Navier-Stokes equations were conducted on 2-D models containing a single intersection constituted by two inlet and two outlet branches, intersected at different angles. The main objective is to study the influence of intersecting angle on the flow behavior of the intersected fractures and the variations of flow patterns and fluid redistribution in each model along with the changes of the Re and the intersecting angle ?. The influence of surface roughness was not considered."

Jan 1, 2015

By A. Galibois, H. Monette, J. L. Collins

This paper deals with the problem of caving, which occurs in varying degrees in blast holes before loading. It is shown that the distribution of the amount of caving in materials may be described by a gamma density function. A decision model to determine the optimal depth of over-drilling 'in order to minimize the expected additional cost per hole is described. Two different policies are discussed. In addition, charts which permit the mine operator to realize significant savings have been drawn for different actual situations.

Jan 1, 1971

By Ki-Bok Min, Seokwon Jeon, Seung-Beum Choi, Taehyun Kim

"In order to investigate anisotropic characteristics of Boryeong shale in Korea, which clearly shows transverse isotropy, a series of experimental tests were carried out. Using Brazilian test, five elastic constants and tensile strength of the shale were evaluated. Elastic constants were determined by iterative procedure and in order to perform this procedure, constitutive model was modified to fit the experimental condition. The anisotropic ratios of elastic constants were evaluated and the applicability of the methodology was assessed. Apparent Brazilian tensile strength profile was investigated and the ratio of the maximum to minimum tensile strength was estimated. Results showed that the tested rock type had low to moderate anisotropic characteristics.INTRODUCTIONMechanical, thermal and hydraulic characteristics of many rocks vary according to direction, which is known as inherent anisotropy, and it is originated from stratified and/or foliated structure of intact rock and discontinuity of rock mass. Anisotropy is one of the long standing issues of rock mechanics field and it has to be taken into account in several engineering fields such as civil, mining and petroleum engineering. An anisotropic medium has 21 independent elastic constants without any assumption of symmetry. If a material has any symmetry, the number of elastic constants required to define its behavior reduces and eventually two constants are necessary if it has complete symmetry, which is known as isotropy. An anisotropic medium that has remarkable planar structure due to its stratification and foliation such as bedding is often called as a transversely isotropic medium. Transversely isotropic model is frequently adopted in many applications especially for sedimentary rock formation and five elastic constants are required to establish the constitutive model."

Jan 1, 2015

By L. B. Kilius

The composite cathode system based on Ce0.9Gdo.1O2_,5 electrolyte with a painted cathode was used for an intermediate temperature (500-700°C) solid oxide fuel cell. This cathode system was chosen due to its excellent thermal expansion match to the electrolyte, its relatively high conductivity (115 S cm-1 at 700°C), and its low activation energy for oxygen reduction (99 kJ/mol). It was found that the decrease of sintering temperature of the composite cathode system produces a significant decrease in charge transfer resistances to a level of 0.25 SI cm2. The conductivity measurements of porous samples produced values between 40 and 88 S/cm for porosities of 30-40%.

Jan 1, 2005

By Leslie McHattie, Sadek E. EI-Alfy

"The Maintenance Engineering Department at Carol Mining and Concentrating is currently in the process of introducing reliability concepts such as failure analysis, rework elimination, predictive maintenance, computerized maintenance history analysis, etc. to improve the over-all maintenance function in the mine and concentratormaintenance areas. Some current initiatives include:• Implementation ofan infrared thermographic scanning program.• Ultrasonic inspection of shafts for all critical equipment in the mine and concentrator areas.• Non-destructive testing of all major welds done by maintenance personnel.• Development of an effective vibration monitoring and analysis program for the production equipment in the mine (shovels, drills, haulage trucks, locomotives).• Failure analysis performed by maintenance engineers to identify the root cause of component failures on critical production equipment.• Computerized breakdown analysis to identify the recurring component failures which contribute significantly to high maintenance costs and production loss.• Implementation of a computerized maintenance management information system.This paper will outline the planned implementation ofthese initiatives, and others, and will also cover the status and results obtained to date."

Jan 1, 1992

By Brian W. Mackenzie

"This paper briefly outlines the characteristics which should be considered in assessing the economics of mineral exploration, and illustrates such an assessment by using data from the Canadian base metal sector. Implications for the sector are found to include the following:(1) base metal exploration has the potential to create a substantial amount of new wealth;(2) investment incentive for exploration under current conditions is not unattractive over-all;(3) because of existing taxation policies, there is much more incentive for large companies to explore than for smaller enterprises;(4) succesful exploration is sensitive to the size, financial resources and organizational structure of the exploration entity;(5) the general level of recent exploration expenditures should be adequate to maintain the current rate of production and perhaps to support very modest growth; and(6) there is an important opportunity for growth in the sector.The findings of the study suggest that government policies should be made more flexible, in order to take into account the risks associated with exploration and with price fluctuations in the base metal sector. Recommendations are also made concerning improvements in provincial regulations for disclosure of exploration information."

Jan 1, 1981

By B. C. Legg, G. L. Tiley

"Many of the ore bodies presently being developed are in remote locations and are, or will be, served by electrical power supply systems of limited capacity.The largest single components of the electrical systems of an underground mine are usually the production hoist drives; the power demands of these drives vary continuously throughout each hoisting cycle.Before 1970mine hoists were driven by either wound rotor induction motors or DC motors in conjunction with motor generator sets.Static Power conversion equipment now costs less to purchase and install and is claimed to be more efficient than motor generator sets. On the debit side, however, it can adversely affect the hoist motors, it operates at relatively low power factors, and it produces harmonic currents.This pa per discusses the effects of static equipment on both DC motors and AC power systems, and evaluates the relative consumption of the three classes of drives."

Jan 1, 1993