Search Documents

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Jin-Young Lee

"Global population is a key factor in future energy requirements, especially considering the important elements of global energy resources, electricity production, the accessibility/non-accessibility of electricity, greenhouse gas emissions and the states of nuclear reactors. Everyday human requirements depend on industrial products, and industries need a considerable amount of electricity to run. Nuclear fuel is inexpensive and bolsters industrial growth. As uranium reserves are being consumed rapidly, an alternative source of energy in the nuclear industry is thorium. Here, primary energy supplies by various sources from 1993 to 2011 as well as estimates of future needs to 2020 are discussed. This study finds that primary energy sources are mainly fossil fuels, renewables sources, and nuclear and hydro energy. In addition, growth depends on increases mainly in renewable sources.Recovery of thorium from its ores by using hydrometallurgical routes were described and discussed. The final part of this paper was presented a case study of the thorium extraction from Korean monazite ore leach liquors by using Prieme JM-T diluted in A150 diluent as an extractant system. And possible separation of the thorium from rare earths (REs) and base metals were calculated by measuring of separation factors and finally, the recovery of thorium from loaded organic of Prieme JM-T was established.THORIUM IS FUTURE NUCLEAR FUEL?Global energy consumption is increasing everyday with the high population growth, high industrialization of numerous countries and the higher level of good and services consumption that follows it. If we look at specific sectors of the economy, oil consumption grew by 0.8 million barrels per day, globally, whereas the increase was 0.4 % for natural gas and coal 1.8 % for nuclear power and just under 2.0 % for hydroelectric power (Asheley 2009). Use of renewable sources of energy for power generation and transportation increased by 3% in 2014 (BP 2015)). Thus alternative source of energy must be identified and developed to meet this increasing demand. Thorium is a potential one for the nuclear industry."

Jan 1, 2016

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965

By J. A. C. Ross

Introduction To enlighten those who may be wondering where anyone could find sufficient data to write a paper on underground concrete work, the author would like to explain that, at Copper Mountain, we have found it necessary to line numerous headings with a layer of concrete in order to keep them in a safe and serviceable condition. The majority of these headings are scram drifts and ore-pass raises. This paper will therefore deal, in the main, with the methods of and reasons for placing concrete in these headings. During recent years, radical changes have been made in the methods of mining ore at the Copper Mountain mine. After considerable experimenting, a mining system has been developed making use of diamond drills for primary breaking and transfering such broken ore through scram drifts with slusher hoists. With the advent of scram drifts, it soon became apparent that some substantial means of reinforcement and protection for the scram drifts themselves would be necessary. Since the orebodies in this mine are cut by numerous dykes or faults, and often both, it was anticipated that some means of support would be required where headings necessarily passed through these incompetent zones. Further, as experience was gained, scram drifts were driven into pillars and in close proximity to old workings so as to recover the maximum amount of ore. In such places, the ground is often severely fractured, either as a result of previous mining or from the effect of excessive rock pressures.

Jan 1, 1950

By Silvana Costa

The quality of life in remote mining communities is a significant factor that impacts the mining industry?s ability to attract and retain high quality workers in remote areas. The rapid growth of mining development, along with the shortage of skills and training globally are reflected in an increasing need to identify the ideal conditions for employee wellbeing and investigate ways to improve quality of life of miners and their families in remote locations.

May 1, 2007

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By Lawrence D. Hoy, Armand Savoie, Pierre Trudel, Ghislaln Tourigny, Robert Crépeau, Lao Kheang

"Recent fluid inclusion and stable isotopic studies in the Bousquet mining district have identified spatial and temporal trends in mineralization temperatures and isotopic compositions of vein forming fluids. These studies indicate that mineralizing temperatures were lower during sterile vein formation (T=200-300°C) than during auriferous vein formation (T = 300-400°C), and that 8 80 values of minerals in sterile veins are lower by 1-3 %o than in associated auriferous veins. In addition to these small differences in 8 80 within individual mineralized zones, a trend of increasing 8 80 values of vein minerals is identified from west to east across the district, with 8 80 of vein minerals increasing by4-6%o. Quantitative evaluation of potential causes of the observed oxygen isotopic shifts suggests that the best explanation for these trends is the derivation of the mineralizing fluids from an isotopically inhomogeneous terrain in which the fluid isotopic compositions are controlled by the isotopic compositions of the host lithologies due to high rock/water ratios in these source terrains. This inhomogeneous source terrain is interpreted as consisting of the Blake River Group volcanics (low 8 80 component) and the adjoining Kewagama and Cadillac Group sediments (high 8 80 component).The genesis of the hydrothermal fluids is attributed to crustal heating during metamorphism, with the fluids representing metamorphic dewatering products and/or fluids incorporated during deposition and burial of the host lithologies. Ductile deformation of the fluid source regions impeded fluid migration during metamorphism; the ultimate release of the mineralizing fluids is attributed to the penetration to depth of vertical structures (fault and shear zones) during brittle deformation of the crust under waning metamorphic conditions. Release of fluids caused by this puncturing of the closed hydrologic source regime produced a localized zone of lowered pressure, drawing fluids from adjacent lithologies toward the fault zones, feeding further hydrothermal fluid upwelling. Au mineralization resulted from chemical processes related to cooling of the hydrothermal fluids and/or interaction with lithologies encountered during fluid migration; the level of crust at which Au deposition occurred likely migrated upward with the thermal anomaly caused by hydrothermal fluid upwelling, eventually reaching the level of current exploitation. Cessation of fluid flow along the vertical structures is attributed to inadequate recharge of the hydrothermal systems as fluid contents were depleted in the lithologies proximal to the vertical structures and/or sealing of the structures by mineral deposition."

Jan 1, 1990

By B. Damjanac, S. Maxwell, D. Chorney, M. Grob, F. Zhang, J. Hazzard

"A hybrid discrete-continuum numerical scheme is developed to study the behavior of hydraulic fractures crossing natural fractures. The fully coupled hybrid scheme utilizes a discrete element model for a core domain, within which the hydraulic fracture propagates and interacts with natural fractures, and a surrounding continuum domain to better approximate boundary effects. The results show that the behavior of hydraulic fractures crossing natural fractures is affected by a combination of factors. Nevertheless, three fundamental crossing scenarios can be identified from all of the simulations: no crossing, partial crossing, and direct crossing. Each crossing scenario has a distinct injection pressure history which may suggest guidelines for interpreting field hydraulic fracture injection data. Additionally, the capability for these models to generate synthetic microseismicity makes them appealing for the integration of microseismic field data with the reservoir geomechanics for ultimately providing a practical engineering tool for improvement of well completion and stimulation. The model is capable of examining and verifying four different shear deformation mechanisms associated with a propagating hydraulic fracture. The natural fracture can fail solely due to the stress perturbation of the passing hydraulic fracture or it can fail due to a combination of stress and pore pressure changes across different types of interaction scenarios. The simulations also illustrate that the level of fracturing complexity increases as the number and extent of the natural fractures increase. INTRODUCTIONAlthough hydraulic fracturing technique has been applied extensively as a reservoir stimulation technique in the oil and gas industry for over 60 years (Economides & Nolte, 2000), it is one of the key factors promoting the shale gas boom in the past decade (King, 2010; International Energy Agency, 2014). The hydraulic fracturing of shales can be differentiated from hydraulic fracturing of conventional reservoirs by the fact that shale formations often have a pre-existing discrete fracture networks which greatly impact the hydraulic fracture propagation. Based upon field production data as well as microseismic observations, it is believed that so called “fracture complexity” may result from interactions between a created hydraulic fracture and pre-existing natural fractures and planes of weakness (Warpinski, 2009; Maxwell & Cipolla, 2011)."

Jan 1, 2015

By W. G. Millar

Until a fire occurs, insurance and prevention work are often looked on as unavoidable necessities, but as insurance is back of all business credit, it is essential to know that in case of damage money will be available to cover the loss; while the interruption of production, often caused by a fire, brings home the realization that if prevention work avoids such an interruption, it is well worth while. Fire insurance is a legal contract guaranteeing the payment of large amounts to an owner, but it is possible there is no other important contract that receives so little consideration. Although previously carried on elsewhere, it is only of recent years that insurance engineering has been actively followed up in Canada, with inspections of an owner's property carried out for his benefit. Now inspections of this kind are made, advice on fire prevention and protection work ?is available, reports with recommendations with regard to the above are furnished periodically, and with this method applied the owner receives the broadest possible cover and security at the lowest cost. Rates are set by the underwriters by rating schedules which charge for defects in a building and allow credits for protection and other favourable features . These schedules are based on the past record of loss of mining properties as a class, so that a fire in another mining property indirectly affects you, but the amount paid is reduced in proportion as your property is improved. The writer feels, from personal experience, that there is no industry where fire prevention receives more attention than the mining industry, and it is a pleasure to advise that, due to this co-operation, some reduction in the basis rates for mining risks is now being made by the underwriters.

Jan 1, 1928

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By J. B. Edwards

"The case is presented for the use of simulators for the computer-based training (CBT) of mining plant operators and for introducing them to automatically controlled systems. As well as their use in the classroom, the role of simulators is examined for ""on-plant"" use in trouble-shooting, fault-finding and maintenance of automatic systems. Case studies are presented showing how specific simulators are becoming established or have potential in the areas of automated materials handling, machine testing, setup and guidance. The evolution of scientific simulations into simulators of widespread practical use is discussed and present-day limitations of computer speed and graphics are considered. Related areas of research for the Canadian Centre for Automation and Robotics in Mining (CCARM) are identified.IntroductionCCARM's Commitment to Simulator DevelopmentAs automation is progressively developed and exploited in mining operations, there arises an urgent need to educate and train staff responsible for its introduction and operation in our mines and for its maintenance. For this purpose , an essential ingredient of an automation program is the development of appropriate mining system simulators for use by a wide variety of personnel. The author has been fortunate to have been closely involved with the development of automatic control systems for a variety of mining machines and mining systems in the United Kingdom. A key ingredient of the research phase in each case has been the use of simulation techniques. As projects have moved toward their commissioning and exploitation phase, the simulations have evolved into simulators tailored for use by machine operators and maintenance personnel. Illustrative case studies are presented later. The researach of the newly constituted Canadian Centre for Automation and Robotics in Mining (CCARM) will likewise involve extensive simulation, and the development of simulators (from the scientific programs) for use at the mine by operators and technicians will be given high priority in the Centre's over-all work program."

Jan 1, 1990

By H. F. Maulson

For the benefit of those who are not familiar with the history of the western Provinces-Manitoba, Saskatchewan, and Alberta-as regards our natural resources, a few words of explanation may be in order before taking up the consideration of the Mines Act of 1930. In 1867, The British North America Act was passed by the Imperial Parliament. That Act, which is our constitution, created a union between the provinces of Nova Scotia, New Brunswick, and Upper and Lower Canada (now known as Ontario and Quebec respectively) under the name of the Dominion of Canada. Provision was made therein for embracing other parts of Canada from time to time. That portion of Canada which today comprises the Provinces of Manitoba, Saskatchewan, and Alberta and the lands to the north of them, was then known as Ruperts Land and the North West Territory. In the year 1670, King Charles II had granted by Letters Patent to Prince Rupert and his associates, known as ?The Governor & Company of Gentlemen Adventurers of England, Trading into Hudson's Bay?, commonly known as the Hudson's Bay Company, the lands and territories therein described, being roughly all the lands adjacent to and west of Hudson's bay; also the gold and silver to be found or discovered therein and other rights as more fully described in said Letters Patent. The land so granted was called 'Ruperts Land'.

Jan 1, 1930

By P. A. Crane, N. Shirley, Aung Moe, H. M. Nicholson, D. Kan

Kazakhstan’s first commercial copper-leach solvent extraction-electrowinning plant, Central Asia Metals’ Kounrad project, was commissioned in April 2012. Exploiting low grade waste stockpiles produced during Soviet era open pit mining, a 10,000 tpa copper cathode plant was designed, constructed and commissioned within 18 months. Overcoming initial challenges with a workforce unfamiliar with the technology and with extensive periods of sub-zero conditions during winter the project has consistently met targets and produced high quality copper cathodes at cash costs of less than US$1/lb. Challenges encountered during the first two years of operation are described and future plans briefly discussed.

Jan 1, 2014

By A. V. Corlett

THE use of the diamond-drill hole as a means of breaking clown ore and waste is not new. Years ago, the method was adopted in mines in northern Ontario and in the western United States to reach out to bad pillars, or to remnants of ore left on walls, the winning of which by any other method might be dangerous or too expensive. The practice is still in vogue and has generally proved a success. Of the known mineral deposits in Canada and elsewhere, many are of very low grade. Some are marginal and not even worthy of being classed as 'ore' until some means is found and proved of exploiting them economically. Other conditions being favourable, if a mining method could be found that would give a large 'bulk break' with a sufficiently low cost of development and a low cast of mining per ton, mineral deposits of this latter type might be brought into the classification of ore. We know that any block-craving system whereby the ore may be undercut and allowed to crush and cave will give a very high breakage and low costs. In some cases, however, the physical characteristics of the ore do not lend themselves to this method. In such ore-bodies, the alternative system of 'bulk-breaking' might be aided by long diamond-drill blast holes. We could obtain this 'bulk breaking' by the use of long diamond-drill holes in conjunction with a sub-level system using extremely thick benches, or possibly by the adaption of modified open-pit methods to underground mining. ln fact, if conditions are favourable, the idea would be simply ta open up a slot or free face and break into it on a larger scale with longer holes. The use of deeper benches-that is, using each level as a sub-level and thereby eliminating much development footage, slashing, setting up, and mucking time-would naturally be expected to lead to cheaper mining.

Jan 1, 1940

By A. S. Dawson

Introduction The purpose of this paper is to discuss, in a general way, the application of geological principles in the exploration for, and development of, deposits of industrial minerals. Mention of geological factors pertaining co specific minerals will be by way of illustration only. Since many prospectors are little acquainted with the geological setting and mode of occurrence of deposits of these minerals, some prospecting possibilities in the field will be pointed out. Geology is a tried and proven tool in the search for and exploitation of metalliferous deposits and of oil and gas fields, but, so far at least as Canada is concerned, only very rarely has a directed, intensive search been made for deposits of industrial minerals. Examples might be cited, however, where, in other countries, such investigations have yielded rich rewards. Thus, development of the vitally important potash deposits of New Mexico was the result of a deliberately planned programme of geological investigation, first by United States Government agencies, and later by private interests. War or the threat of war, or peace-time industrial expansion, can render concentrated exploration for specific minerals desirable or even essential. Such exploration is, primarily, a geological problem. Admittedly, there is in general less scope for the application of geology in the search for, and development of, deposits of industrial minerals than of metalliferous minerals, oil, etc. Where the latter are concerned; the objective of exploration is to find a material that is valuable, within broad limits, no matter where it is located or how it occurs. The unit value of the material is limited only by the amount of the valuable constituent in the formation- its possible upper limit is tremendously high. On the other hand, many industrial minerals constitute in themselves 90 per cent or more of the formation- their amount cannot increase and their unit value is commonly low. Moreover, for commercial exploitation, the deposit must, in general, be reasonably close to markets or to plant or other facilities for processing the raw material, since, owing to its low value, this cannot be transported any great distance. As a consequence, intensive geological search for and investigation of such deposits has been restricted to industrialized areas. Obviously, however, it is good insurance for any operator to understand the geological background of his deposit, particularly in the case of new developments.

Jan 1, 1949

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017

By Pierre Buteau

Peat/ands distribution in Canada is widely spread thoughout the country and corresponds to a wide spectrum of wetland habitats which overlay peat deposits. The development and the evolution ofpeat/ands and peat deposits are closely linked together, since the vegetal remains of the peat deposits originate from the peatland habitats, and the peatland habitats constitute a response to many factors, including the properties of the substrate, which are the peat deposits. Peat/ands are defined as waterlogged terrains where the production of plant materials usually exceeds the rate of decomposition. The underlying peat deposits consists of organic residues associated to peatland vegetation, more or less decomposed, built up and kept under anaerobic conditions. Peat/ands evolution and distribution are determined primarily by climatic factors, but also by the geomorphology and edaphic conditions. All of these create particular hydrodynamical environments which will vary according to different regional settings, and sequentially to an evolutive time frame.

Jan 1, 2001

By X. Cao, A. Birur, R. R. Chromik, J. Cuddy, P. Wanjara, J. Gholipour Baradari, T. Shariff

In this study, 3.1 mm thick Ti-5553 (Ti-5Al-5V-5Mo-3Cr) butt joints were autogenously welded using a 4 kW continuous wave Nd:YAG laser. The effect of welding speed and defocusing distance on the weld quality was investigated in terms of the surface morphology, welding defects, microstructure and hardness. Welds with full penetration were achieved at a defocusing distance ranging from -1 mm to 0 mm and welding speeds from 2.25 to 6.0 m/min. Underfill and porosity were the two main defects most frequently observed but within the optimum process window these defects could be maintained to meet aerospace specification tolerances. The fusion zone (FZ) consisted entirely of retained beta with a refined dendritic morphology. Compared to the bimodal alpha (a) + beta (ß) microstructure of the base metal (BM), the dissolution of the a phase was observed in the heat affected zone (HAZ), which led to an 11 % decrease in hardness from the BM to the FZ. To determine the tensile properties of the welded samples, an automated 3D deformation measurement system was used to measure the local strain in the weld region. The yield strength (YS) and ultimate tensile strength (UTS) increased with increasing welding speed with a highest joint efficiency of 75 % being achieved, albeit with a concomitant reduction in the ductility.

Jan 1, 2010

By L. R. Wilkinson, W. J. Howarth, G. J. Wenk

Over a period of three years, a cooperative program in Australia has resulted in the development of radioisotope immersion probes for the on-stream analysis of mineral slurries. Two basic probe types are now available on a commercial basis - fluorescence and absorption probes - and within each type there are a number of variations so that optimum sensitivities can be obtained for elements with atomic number greater than titanium (22), thus covering most metals of interest to modern metallurgy.

Jan 1, 1973

By J. -F. Blais, M. -O. Simonnot, P. Charbonnier, J. Mocellin, Université de Lorraine INRA, G. Mercier

"Huge amounts of air pollution scrubber sludge have been generated during ferromanganese production using blast furnace. These residues have been historically deposited in ponds near steel making plants. They are very rich in zinc, manganese and lead (5 to 40 %) and also contain aluminum and iron. Considering the market value of these metals, brownfield sites can now be used as secondary resources. These ponds also have to be cleaned up to meet the environmental regulations.We have developed a hydrometallurgical process to recover Zn, Mn and Pb in order to produce valuable compounds of Mn and Zn and recover the final Pb residue by pyrometallurgy. The Zn and Mn compounds need to be pure enough to be economically valuable. Batch laboratory tests were carried out to determine suitable selective leaching conditions. The investigated operating conditions were acid concentration, pulp density and temperature. Optimal conditions to maximize zinc extraction (100 %) and manganese extraction (95.9 %) were found using sulfuric acid and sodium metabisulfide. The final residue contained 14.8 to 23.8 % of Pb. Then, Zn was recovered in the form of ZnO or ZnS by precipitation and Zn metal by electrowinning, while Mn was recovered as MnCO3 with a fairly acceptable concentration of impurities.INTRODUCTIONFerromanganese has been produced by pyrometallurgy in much of Western Europe for centuries. Use of wet scrubber to remove pollutant and dust particles from gas stream was common for most of these operations. Those residues contain high concentration of Zn, Mn and Pb. They have been left to decant in settling ponds installed close to the steel production plants. They now constitute heavily contaminated artificial soils. Those sludges are so contaminated with Zn, Mn and Pb that they can be used for metal production. Currently, no method is available to decontaminate these residues and recover Zn, Mn and Pb. Therefore, an approach considering these brownfield sites as secondary resource is in development. Doing so would achieve two goals, decontaminate the site and produce metals.. (Huot, Faure, Biache, Lorgeoux, Simonnot, & Morel, 2014a; Huot, Simonnot, Marion, Yvon, De Donato, & Morel, 2012; Huot, Simonnot, Watteau, Marion, Yvon, De Donato, & Morel, 2014b)."

Jan 1, 2016