Search Documents

By R. F. Favreau, L. C. Lang

"In modern blasting technology blasts are designed and analysed on an energy-mass-time relationship. The energy of the explosive is derived by computer analysis and the work potential of the available energy is expressed in numerical values. The mass involved in the blast is determined by the geometry of the blast and by the rock density. Time is also a relevant parameter, because time is required to complete the three basic stages of the breakage process.For successful application of the blasting parameters the basic mechanism of the breakage process must be understood.The physical-mechanical properties of the rock, local structural geology and the thermodynamic properties of the explosives can be brought together to create a computer model of a blast with which it is possible to predict separately the results of each parameter and to express the predicted degree of change in any parameter by actual numbers.A long-range project has started to create a ""bank"" of rock properties for as many Canadian and foreign mines as possible. A computer model has been successfully applied to predicting the effect of varying the ratio of spacing to burden at constant rock volume and significantly improved results are achieved, as the S/B ratio is increased up to about 2 to 2.5.High-speed photography has been applied to determine the time that has elapsed between zero time and the beginning of movement of the mass. The results assist in determining minimum and optimum delay time required for multiple-row blasting.The approach as described in the paper is now well proven and is clearly superior to previous methods based on powder factors and human assessment."

Jan 1, 1972

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By K. Turgeon, D. Larivière, L. Whitty-Léveillé, J. -F. Boulanger, C. Bazin

"The processing of ore containing rare earth elements leads to the production of an impure solution of these elements. The separation of the rare earths from the impurities and the production of individual elements is usually carried out by solvent extraction. The effectiveness of the extraction conditions and of the reagents is generally tested in the laboratory. This paper deals with the processing of results from solvent extraction laboratory tests planned to generate data redundancy. A method is proposed to take advantage of the data redundancy by accounting for the pH variation during the extraction. The parallel processing of several tests also allows estimating the equilibrium constants for the extraction. The proposed method produces equilibrium constants that are more reproducible than values estimated using conventional approaches. The method is illustrated with solvent extraction tests conducted on synthetic solutions of rare earth elements.INTRODUCTIONThe processing of ores containing rare earth elements (REE) usually includes the production of a concentrate of the minerals carrying the REE. These minerals, for instance monazite and bastnäsite, contain the 14 elements from La to Lu plus yttrium and scandium. As an example monazite has the general formula of (La,Ce,Pr,Nd,Sm,Eu,Gd,Tb,Dy…Lu)PO4 with a typical lanthanum content of 20-26%, cerium content of 40-50%, praseodymium of 4-6%, neodymium of 16 to 20%, and decreasing concentrations of heavier elements (Gupta & Krishnamurthy, 2005). During the processing of a REE mineral, it is generally not possible to isolate and separate a single REE from all the rest. The mineral molecules need to be broken (usually via a heat treatment followed by leaching with a base and/or an acid) to produce an aqueous solution of the REE of the ore. After purification of the solution, the REE can be precipitated as a bulk concentrate and sold to a refinery that separates the REE into particular groups of REE such as the light versus heavy REE or into individual elements such as lanthanum, neodymium, or europium oxides to yield value-added products."

Jan 1, 2016

By M. J. Davie, D. S. Ross

"The successful design of a new mine water pumping system is in part dependent upon the accuracy with which the operating conditions can be forecast. This paper outlines the data which should be obtained on water quantity and quality. Methods of modifying the quality are also discussed. Some pumping systems for disposal of sludge are described, citing operating examples. The various types of mine dewatering pumps are described in terms of design characteristics as they affect operating efficiency and installation and maintenance costs. Piping system parameters are outlined. Finally, a hypothetical case study of pumping from a depth of 3,000 ft is assessed, with particular reference to capital costs.IntroductionMany mine operators would agree that the pumping system usually receives a low engineering priority during the design stage, and as a consequence causes some of the most frustrating problems during production. For a ""dry"" mine (up to 200 gpm), design of the pumping system may indeed be simple, but outside of the potash industry such mines are not common. For ""wet"" mines, the pumping system is important because it significantly affects the initial capital and on-going energy costs of the mine and, in the area of sludge disposal, the working conditions and production costs. Indeed, a failure in the pumping system usually has serious, and sometimes disastrous, consequences.The intent of this paper is to outline the factors which should be considered in the design of a pumping system and to describe the types of pumps used in mine dewatering and relate them to practical operating systems."

Jan 1, 1980

By L. R. Plitt

A series of experiments were carried out in an effort to develop a universally applicable mathematical model of the hydrocyclone classifier. The design and operating variables studied were: cyclone diameter and height, the inlet, vortex finder and apex diameters, the feed pressure and the solids content of the feed slurry. The model consists of four basic equations which express the cut size ( dso), volumetric split between overflow and underflow, volumetric throughput, and sharpness of separation in terms of the operating and design variables. Although empirical, the model is nevertheless in general agreement with fundamentally derived models. The model clearly 1•eveals the effect of the major variables on the operation of a hydrocyclone. Because of its broad data base and the inclusion of all the major variables, the model may be used without experimental data to predict the operation of cyclones over a wide range of different operating conditions. With operating data, the equations may be modified to serve as an operational model.

Jan 1, 1976

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By B. A. Zaharov, J. M. Shneerson, L. V. Chugaev, M. T. Zhunusov, A. M. Markelov, S. V. Drozdov

The main direction of research was the application of autoclave technology for the flotation concentrates or biooxidation feedstocks. The industry modernization also expects the possibility of increasing the yield of the flotation concentrate, to allow an increase in gold extraction in flotation circuit. This paper provides brief description of results obtained for concentrates with the yield of 4 and 8%, as well as corresponding biooxidation feedstocks. Technological efficiency of autoclave oxidation is shown for both concentrates and biooxidation feedstocks. The process has been evaluated on a laboratory and a continuous pilot plant scale. Gold extractions from POX discharge are ranging from 94-97% for each product, with only 5-7 kg/t cyanide consumed.

Jan 1, 2014

By G. K. Lee, E. R. Mitchell

Designers of combustion processes may select aerodynamic conditions which produce only superfine fly ash. Although it is not usually anticipated that this will create a problem, such as has been found to agglomerate in high-velocity gas streams, to plug mechanical dust separators in a short time, and to contribute to atmospheric pollution. The problem is a fundamental one, and may be approached in several ways. The authors, in the course of their combustion research program, had occasion to examine the agglomeration of ash, ranging from sub-micron to 17 microns in size, produced in a (coal and oil) dual-fuel-fired steam generator. Several theories, supported by extensive laboratory studies, have provided some understanding of a probable mechanism of agglomeration. As a result, certain precautions are suggested in the design and selection of combustion processes and equipment.

Jan 1, 1962

By Z. F. Zhou, X. Y. Zhou, V. G. Papangelakis, Z. D. Jankovic, S. M. Ulyanov, S. N. Lvov

Recently developed flow-through electrochemical techniques (1,2) were employed for measuring pH in high concentration aqueous solutions and geothermal brines. The pH values of (1) 5.0 mol kg-1 NaCl + x mol kg-1 HCl, (2) 3.0 mol kg-1 of NaCl + 0.5 mol kg -1 of KCl + 1.0 mol kg-1 of CaCl2 + x mol kg-1 HCl (x < 0.1 mol kg-1), and (3) mixtures of Al2(SO4)3-H2SO4-H2O, MgSO4-H2SO4-H2O, and NiSO4-H2SO4-H2O solutions have been measured at temperatures from 100 to 280°C. The obtained experimental data and their thermodynamic analysis demonstrated that the electrochemical system can be used for on-line pH monitoring of high concentration aqueous solutions with an accuracy of ±0.1-0.3 pH units over a wide range of temperatures. Greater deviation exists in real laterite leach solution measurements due to in situ precipitation of Na-alunite. The system is excellent for research and process development work. Further work is needed to ensure robust operation under pressure leach conditions of laterites.

Jan 1, 2004

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By M. Melashvili

"The SART Process was introduced to the gold mining industry in the late 1990s and several commercial plants were built over the following 10 to 15 years. Most of these plants have operated well and enjoyed plant performance in line with expectations based on the underlying chemistry of the process. However, two of the plants have consistently suffered from high reagent consumption and poor product quality, which has motivated a re-examination of the process fundamentals.The primary product in the SART Process is synthetic chalcocite, Cu2S, and the stoichiometric requirement for sulphide addition is therefore 0.5 moles per mole of copper in solution. It is shown here that when sulphide is added in excess of this amount (generally with the express purpose of lowering residual copper in solution) it not only fails in its intended purpose, but can have a negative impact on the settling and filtration characteristics of the copper sulphide product, as well as the final product quality. Moreover, these problems are exacerbated the higher the selected operating pH in the pH 3 to 5 range, and the longer the residence time of slurry in this pH range.Freshly precipitated copper sulphide compounds are known to be very fine and slimy, with poor settling and filtration characteristics. It is therefore important to engineer the SART Process in such a way as to encourage growth in the average particle size of the precipitate crystals. This was the rationale for recycling a portion of the thickener underflow to the primary reactor when the SART Process was developed. However, the theory of crystallization predicts that compounds of extremely low solubility, such as chalcocite (Cu2S: KSP = 10-48), are unlikely to experience growth in crystal particle size through heterogeneous nucleation and are more likely to grow through aggregation. On this basis, the SART practice of recycling a portion of thickener underflow to the primary reactor in the commercial plants is unlikely to lead to crystal growth via nucleation, and could in fact promote breakage of the aggregates that formed in the thickener. Recycling thickener underflow could therefore have the opposite of the desired outcome. The result of testwork that is reported here lends credence to this theory and questions the wisdom of recycling in the SART process."

Jan 1, 2016

By H. J. H. Pieterse

Agitation requirements in oxidation autoclaves can vary widely depending on the mineralogy of the feed material and the specific process selected. Before selecting an agitation system it is important that the client specify the desired throughput, mineralogy, chemistry, kinetics, compartments, overall retention time, and the desired oxygen utilization. In selecting the agitation system, the factors mentioned above as well as oxygen solubility, oxygen mass transfer coefficients, and specific power are evaluated. Much research effort has been directed toward open tank systems for fermentation and oxidation processes. However, for high pressure autoclave oxidation processes little information is available. In this review the author&apos;s experience in the autoclave industry and some of the available literature are utilized to compare the installed power per unit volume with some of the methods proposed for open tank oxidation. Equations that appear to give results close to that experienced in the industry have been identified. Further work is required in this area to develop a higher degree of confidence in the ability to predict the power required for any given case.

Jan 1, 2004

By Dale L. Pitt

Introduction In opening up a new country, one of the most vital problems is that of transportation Without roads, railways, or water routes, development is very slow because these are the arteries through which the life-blood of the country flows. British Columbia is unusually fortunate in having along its western coast, for some 600 miles, a stretch of inside water unequalled, for comfortable and safe navigation, by any other similar stretch of ocean in the world. This solves in a general way the major north and south transportation problem for the coast section, and offers comparatively cheap rates for the shipping of all commodities. The principal cities and centres of distribution will naturally grow up on the coast. These cities, however, must have methods of communication with the hinterland, and it is the necessity of supplying these, as feeders to the principal ports, which presents problems of considerable magnitude.

Jan 1, 1930

By M. A. Hardie

"CASES and mixtures of them are so common and so much a part of everyday existence that they become so taken for granted that their individual characteristics and idiosyncrasies rarely become of curiosity to others than those involved in tl1eir production, processing, treatment, transportation, and for utilization. The use of the most common and universal mixture of gases -air -is begun at birth by ail living creatures and their discontinuation of its use terminates existence. Modern man rides on air in his tires, rides through it for high-speed transportation, and uses it for his comfort in the heating and air conditioning of his domicile. It is neither the aim nor the in-tent, in the next few moments, to provide a panacea for even a portion of the problems inherent in the gas industry nor to delve deeply into any particular facet of its diversities. The purpose is primarily to touch upon some of the peculiarities and generally to consider approaches to employ in the pursuit of solutions."

Jan 1, 1959

By G. Cailletaud, I. Guillot, D. Larouche, R. Martinez, D. Massinon

The precipitation of Al2Cu particles in a 319 T7 aluminum alloy has been modeled. A theoretical approach enables the concomitant computation of nucleation, growth and coarsening, based on an implicit scheme using the finite differences. The equation of continuity is discretized in time and space in order to obtain a matricial form. The inversion of a tridiagonal matrix allows us to determine the evolution of the size distribution of Al2Cu particles at t + dt. The fluxes of solute in-between the boundaries, as well as the ones at the boundaries, are computed in order to respect the conservation of the mass of the system. The main results of the model are compared to TEM measurements. Simulations provide quantitative features on the impact of the cooling rate on the size distribution of Al2Cu particles in good agreement with the TEM measurements. This metallurgical model is integrated into FEA software in order to perform mechanical computations. This kind of multiscale approach allows new perspectives to be investigated in the process of designing cylinder heads. It enables a more precise prediction of the microstructure, its evolution as a function of continuous cooling rates and its impact on the integrity of the structure.

Jan 1, 2015

By Alan E. Gallie

One of the requirements for the successful waging of war is an unlimited supply of iron ore. In the spring of 1941 the demand for iron ore was expected to exceed the supply. This was particularly so in the case of high-grade lump iron ore, essential to the open-hearth process of making steel. The bulk of Canada&apos;s iron ore was imported from the United States. At this time, Canada was making every effort to conserve United States funds for more vital purchases. For these reasons, the development of Canadian iron ore resources became of prime importance. Several companies undertook investigations and one of these examined the old Josephine deposit. Location The Josephine property is in the district of Algoma, in the Michipicoten area of the Sault Ste. Marie mining division of Ontario. It is 120 miles north of Sault Ste. Marie and 20 rail-miles east of Michipicoten harbour, on lake Superior (see Figure 1). Transportation in the area is furnished by the Algoma Central and Hudson Bay railway. The Michipicoten branch of this line passes within a mile of the Josephine mine. Michipicoten harbour provides a port through which iron ore is currently shipped. Power in the area is supplied by the Great Lakes Power Company, with generating plants on Michipicoten river, on Montreal river, and on St. Mary&apos;s river at Sault Ste. Marie. A series of transmission lines cover the district and one of these is connected to the Josephine mine by a 3 ½-mile branch line. History The Josephine property was staked by Alois Goetz in 1899. Before the claims could be recorded, the township in which they are located was given to the Algoma Central & Hudson Bay railway as part of a land grant. As a result, the ownership remained in dispute until August 24th, 1906, when a settlement was arbitrated by the Honourable Frank Cochrane. His ruling is interesting and is quoted in part.

Jan 1, 1947

By Shintaro Takamiya, Kazunari Yoshida

"Recently, small sized micro-needles for medical are required more frequently by patients. The biggest reason is that it presents great burden on the patients, due to the size of the needle injection. People need to use a very small needle to lower the pain, but the downfall is that it makes them more expensive due to their complicated manufacturing method. Therefore, we need to fabricate a needle by wire-drawing to decrease its price. Tube-drawing is beneficial for its production value; however, in conventional tube-drawing it is difficult of control the wall thickness of the tube and makes it 1mmor lower in diameter. That is why, we propose fluid-mandrel drawing for new tube drawing. This method allows fabrication of a fine tube by using the pressure of the fluid in the tube. In this research, the goal is the fabrication of a fine tube by fluid-mandrel drawing and its evaluation. Finally, the fabrication of a fine tube by fluid-mandrel drawing was conducted and in result a tube with a diameter of 0.2mm, high strength and thin wall and fine inner surface was drawn, which can be used as a lesser pain micro-needle.INTRODUCTIONThe main manufacturing method of the current medical needles is roll forming. With this method, it is difficult to make a tube with a diameter lower than 1mm. Deep drawing has been proposed and used as method to further reduce the diameter, but this method is costly and the injection needle obtained by this method is several times more expensive.Therefore, we need to obtain a fine medical needle by drawing process that can be mass-produced and inexpensively manufactured. However, with the conventional drawing process, it is not possible to obtain a syringe needle with a reduced diameter easily, that is why, a fluid-mandrel drawing has been proposed which can reduce the diameter without damaging the inner surface. The methodology of the method is, a fluid is filled in the sealed tube and the pressure inside the tube during drawing is responsible for the good inner surface and wall thickness. It is also expected that the fluid can be easily discarded and that the tube can be manufactured on a long scale."

Jan 1, 2017

By C. Jay Hodgson, P. J. MacGeehan

"Of the 135 current or past-producing 'gold-only' mines in the Superior Province of the Canadian Shield which have produced more than 100,000 tons of ore, the 33 mines which have produced one million ounces or more of gold have accounted for over 84o/o of the total production of 137 million ounces. The published literature on these 33 deposits was reviewed in order to determine the geological setting of the mineralization on a regional (mining camp) and local (mine) scale. The dominant rock types underlying the mining camps are mafic, variolitic, tholeiitic volcanic rocks with a significant ultramafic (komatiitic) component, and clastic and/ or exhalative sedimentary rocks. Felsic volcanic rocks are generally subordinate. Most mining camps are located at or near the top of the mafic-ultramafic sequence, and generally there is a major sedimentary-volcanic contact present which may be 1) a stratigraphic superposition of volcanic and sedimentary units, 2) a rapid, along-strike gradation from dominantly volcanic to dominantly sedimentary units due to facies change, or to the formation of structurally controlled sedimentary basins during volcanism, or 3) frequently (at 40o/o of the camps) a juxtaposition of sedimentary and volcanic sequences across a major fault zone or 'break', which in many instances may represent a reactivated, syn-volcanic basin-margin fault.In contrast to the regional setting, on a local or mine scale over 90o/o of the 33 mines contain felsic intrusions and/ or extrusions within mine workings. The felsic rocks may be quartzbearing (commonly quartz-feldspar porphyries) or dominantly quartz-free (commonly feldspar porphyry syenites or monzonites), and appear to have been emplaced in two different depth-zone environments: an epizonal intrusive environment, and a volcanic vent environment. Although the distinction between epizonal intrusive and volcanic intrusive-extrusive rocks is uncertain in many deposits, the two are tentatively separated on the basis of the grain size of the rock matrix (medium to coarse grained vs aphanitic to fine grained), homogeneity (multi-phased and/ or compositionally zoned vs compositionally homogeneous), and the shape and relationship to stratigraphy of the igneous body (circular or oval in cross section, and cutting the stratigraphy at a low angle vs lenticular and either stratiform or cutting the stratigraphy at a high angle). In addition, felsic intrusions of the volcanic environment commonly grade into tuffs or breccias of extrusive origin, whereas epizonal intrusions do not.Stratiform ore zones of possible exhalative sedimentary origin appear to be confined to deposits in which volcanic felsic rocks are present, and are absent from deposits in which only epizonal felsic intrusions are present. Pervasive carbonate- rich alteration, commonly in roughly stratabound zones of regional extent, and carbonate-rich chemical sedimentary rocks are present in over three-quarters of the deposits containing quartz-bearing felsic volcanic rocks, but are much less common in deposits with quartz-free felsic volcanic rocks. The host sequences of epizonal felsic intrusions which are quartzfree are more commonly sedimentary than those of quartz-bearing epizonal felsic intrusions.Quartz, carbonate minerals, arsenopyrite, scheelite, tourmaline and Cr-muscovite ('juchsite') are the most common mineralogical associates of gold. Arsenopyrite is essentially restricted to the volcanic environment, occurring in about twothirds of the deposits with quartz-bearing felsic volcanic rocks and less than half of the deposits with quartz-free volcanic rocks. Tourmaline, on the other hand, is almost ubiquitous in deposits associated with epizonal intrusions and also occurs in about two-thirds of the deposits associated with quartz-bearing felsic volcanic rocks, but in only one of the eight deposits associated with quartz-free felsic volcanic rocks. Scheelite is essentially restricted to ores of quartz-rich fel"

Jan 1, 1982

A newly developed damage model was used in the study of rock fragmentation mechanisms involved in crater blasting. Simulations show that at the detonation of the explosive charge, a crushed zone around the explosive charge is formed due to compressive failure and then a strong pressure wave is sent out forming a pressurized ring that propagates at the dilatation wave velocity. As the pressurized ring leaves the crushed zone, two tensile stress components perpendicular to the radial stress are developed in response to the action of the radial pressure, causing tensile failure and forming a damage zone around the charge. The formation of this damage zone is quite independent of the depth of the explosive charge provided there is no interference by the reflection from the free face. When the pressurized ring reaches the free face, it is reflected there and causes rock failure on the ground surface that forms another damage zone. Under the simulation conditions, it is revealed that the depth of charge is a factor controlling the relationship between the two damage zones. At a depth smaller than the optimum, the two damage zones coalesce into one and there is excessive rock breakage; otherwise, the two damage zones tend to isolate from each other with the increase in the depth of charge. Calculations of fragmentation indicate that the average fragment size increases and the uniformity of fragments decreases when the depth of charge increases as observed in practical blasting.

Jan 1, 1998

?Founded in 1969 by the Ruia family ?Diversified global business corporation with a balanced portfolio of assets in the manufacturing and service sectors; $15 Billion revenue in FY 2009-2010 ?Employs 70,000 people worldwide with offices in Asia, Africa, Europe and North America

May 1, 2011