Search Documents

By I. C. Edwards, E. O. Lilge, H. H. Mccreedy

"Introductory and GeneralTHE DRIESSEN CONE bas been used fairly extensively commercially as a classifier. Its use as a concentrator in the upgrading of ores at a fairly high ratio of concentration with concomitant recoveries has been almost negligible. Certain known features about the cone, however, such as its high throughput capacity, cheapness of construction and operation, and simplicity of design have attracted the attention of mill men. An inadequate knowledge of the operating characteristics of the cone when used as a concentrator seems to have been the main reason for its lack of use. It was for this reason that the present investigations§ were undertaken to determine the operating characteristics of the cone and its application to the concentration of uranium ores, with particular emphasis being placed on the concentration of low-grade uranium ores.The investigations were started in December, 1951, and have continued uninterrupted to the present. The initial work was confined chiefly to investigating the operating characteristics of the cone in order to establish the trends that certain variables would exert on the general metallurgy of uranium concentration. Optimum metallurgy was therefore not the prime initial objective."

Jan 1, 1955

By Michel Rodrigue, Sylvain Duchesne, Louis Racine

"LocationThe Louvicourt mine is located 20 km east of Val d'Or in Abitibi, in the northwest part of the province of Quebec. The mine is located on Highway 117 connecting Val d'Or to Montreal and very close to the main railway networkHistoryFive successive exploration attempts by Aur Resources resulted in the discovery of the large Louvicourt orebody in June 1989. Construction of the surface and underground infrastructures commenced in the spring of 1991. Milling operations commenced in July 1994. The entire project cost CDN$290 million, almost CDN$20 million less than initially estimated. The concentrator infrastructure cost CDN$64 million.Louvicourt mine is owned in partnership by Novicourt Inc. (45%), Teck Corporation (25%), and Aur Resources Inc., the administrator (30%).Brief DescriptionLouvicourt mine is the largest producer of base metals (Cu and Zn) in Abitibi-Temiscamingue. Its average daily production is nearly 4300 t of ore, for an annual production of 200 000 t of copper concentrate (28% Cu) and 33 000 t of zinc concentrate (57% Zn). After only a few weeks of operation, it had attained its objectives for the most part, and operations continue to be improved."

Jan 1, 2000

By Pizhi Zhao, Yingdong Li, Hailong Cao, Yingjuan Feng

"Three types of anodic films (unsealed, hot water sealed and agent sealed) were prepared to study the effects of anodizing pores structure on the adhesive bonding performance of AA5754 automotive sheets. The morphology of the anodic films was examined by using scanning electron microscope (SEM) and the composition was examined by glow discharge optical emission spectroscopy (GDOES). The adhesive bonding strength and durability in corrosive environment were investigated by using single lap shear test and salt spray corrosion test (SST), respectively. The results showed that the pores structure could significantly influence the adhesive bonding performance. The unsealed sample showed porous structure and provided high bonding strength, however, the durability was poor in corrosive environment. The hot water sealed sample showed fine and loose hydrated alumin a structure on the surface and provided high durability in corrosive environment, but the bonding strength was low. In contrast, the agent sealed sample provided both high bonding strength and durability in corrosive environment.INTRODUCTIONAdhesively bonded aluminum joints by using adhesives have been widely used for the realization of lightweight design in industrial applications like automotive and aerospace industry[1, 2]. Durable bonds which are capable of taking structural loads can be created due to a careful consideration of the way in which the joint is formed, the type of adhesive and the appropriate treatment of the adherend surfaces prior to bonding[3-6]. Experiences demonstrate that the surface treatment is the most critical step which could not be disregarded, since it is essential to achieve long-term service capability [7].In structural applications, a bonded assembly is expected to maintain a significant load and may be combined with exposure to harsh environmental conditions in its service life. For this purpose, the pretreatment for structural bonding of aluminum alloy must provide not only strong tensile strength and durability but also good corrosion resistance. Chromic acid anodizing (CAA) process provides an anodized layer which has good corrosion resistance while also exhibiting useful adhesion characteristics as well as lacquer coating retaining characteristics[8].However, the use of Cr (VI) is unadvised from a health and environmental point of view since it is toxic and carcinogenic, and this process is gradually limited even prohibited. Boeing's phosphoric acid anodizing(PAA) process provides a more open pore structure allowing penetration of high molecular primers/adhesives[8]and PAA process is the most widely used pre-surface treatment suitable for adhesive bonding between aluminum alloy components. Rahimi et al. demonstrated that nanostructure can be produced by PAA process and is affected by the time of pretreatment and anodizing parameters [9]. Xu et al.investigated the influence of surface energy and roughness on adhesive bonding through PAAprocess and provided improved adhesion performance under certain anodizing parameter[10]. However, PAA process is normally not recommended for a major concern of deterioration of the mechanical performance of the joints as a result of exposure to a wet and corrosive environment. Sulfuric acid anodizing(SAA)process, recently, has been widely used for corrosion protection and good base coating for the adhesion of lacquers in aerospace manufacturing[11]. The good performance is explained by properties such as the porous morphology and high adsorptive power of the oxide film, the chemical and electrical inertness of the anodized layer. Moreover, modified sulfuric acid could also used for adhesive bonding. Lunder et al. found that anodizing in hot sulfuric acid is promising as a simple, very rapid and environmentally friendly pre-treatment for adhesive bonding[12].Saeedikhani et al. studied the process of phosphoric/boric/sulfuric acids anodizing and found it was is a promising pre-treatment for adhesive bon"

Jan 1, 2018

By W. T. Martson

ABSTRACT Sooner or later, every producing mine faces the question of fill. This paper invites consideration of mill tailings as an economical, efficient, and quantitatively adequate source of such fill. Some of the advantages, disadvantages, methods of utilization, and methods of treating mill tailings for sand recovery are covered. ADVANTAGES AND DISADVANTAGES OF SAND FILL DISREGARDING economic com-promise, that material which supports the greatest applied load with the least compression is the best choice for fill. Table I, reproduced from U. S. Bureau of Mines Bulletin 60, is offered as evidence of the adequacy of hydraulically placed sand. Table II gives the results of tests made in an effort to determine the reason for the difference between load hearing qualities of dry-placed and hydraulically-placed sand. From these, it would appear that hydraulic placing gives a denser initial packing, with corresponding higher, and faster development of, load bearing qualities. Assuming this to be true, then if sand from mill tailings can be placed underground economically, it is the superior fill material. Table III summarizes cost data available. The most cursory glance through the available references (2, 5, 6, 7, 8, 9) will show .that the major benefit from the adoption of sand fill is a decrease in the non-productive fill ?cycle of a working place. This, it is estimated, increases the output of an individual stope by from 25 to 50 per cent. The advantage of reducing the number of required working places for a constant daily production is obvious.

Jan 1, 1951

By C. H. Stockwell

"The Precambrian rocks of southeastern Manitoba contain a great variety of mineral deposits, including gold, chromium, copper, nickel, lithium, tin, beryllium, tungsten, and molybdenum. Although considerable interest has been shown from time to time in each of these types of deposit, production to date has been almost entirely in gold. This has had a value of about $26,000,000 and has been derived chiefly from the San Antonio mine, with lesser amounts from the Central Manitoba, Gunnar, Beresford Lake, Ogama-Rockland, Diana, and other properties.Most of the deposits lie within volcanic and sedimentary rocks or within basic intrusions cutting these rocks. These favourable rocks occur in several areas, which have been given local names and are separated from one another by large bodies of granite (Fig. 1).In general, the several areas are characterized by different types of mineralization. Thus, the Rice Lake-Beresford Lake area contains numerous gold deposits and has yielded almost all the gold production to date; the Maskwa River, Euclid Lake, and Oiseau River areas are, on the whole, characterized by deposits of chromium, copper, nickel, lithium, tin, and beryllium; and in the West Hawk Lake area there are deposits of gold, tungsten, molybdenum, and lithium.As might be expected in a district containing such a variety of mineral deposits, the structural conditions controlling their deposition also vary greatly. It is, accordingly, convenient to discuss the structural geology and mineral deposits of each of the more important areas separately."

Jan 1, 1954

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By T. C. Cheng, G. P. Demopoulos

It is the object of this paper to discuss various options for improving the hematite process in terms of increased throughput hence lower capital cost and production of saleable quality hematite. With reference to increasing the throughput of the process, it has now been determined via the analysis of Akita Zinc Co's continuous industrial autoclave performance data that the process kinetics is limited by the rate of the hydrolytic precipitation reaction. By correlating the hydrolytic precipitation rate to supersaturation ratio, it is shown that accelerated kinetics can be achieved via the following measures: (1) in-situ neutralization with addition of zinc calcine; (2) elevation of temperature; and (3) dilution of feed; of which, the first one was retained for further evaluation. According to presented estimates, addition of calcine, amounting to only 2.6% of the total zinc calcine processed, can allow for shortening the retention time by at least 50%. Such drastic shortening of retention time may be either used to increase the throughput of a given autoclave circuit or alternatively to release autoclave capacity for clean hematite production. Hydrothermal treatment of the crude hematite product proved effective in producing clean hematite as according to laboratory tests, hence allowing the sulphur content of hematite to be reduced from around 4% to less than 1%. A conceptual flowsheet incorporating in-situ neutralization for accelerated kinetics with hydrothermal upgrading of crude hematite without sacrificing production capacity and with minimum upset of the plant's water balance is described.

Jan 1, 2004

By B. McHenry, A. E. Wraith, P. J. Mackey

The Wallaroo smelter on the Yorke Peninsula, South Australia commenced smelting operations in 1861 treating ores from the nearby Moonta and Kadina mines. The plant expanded and modernized on several occasions and was a leader in the successful introduction of new technology to improve operations. It operated continuously until 1923 when local mines became exhausted; in the closing stages of the 19th century it was the largest copper smelter in the world outside of those in Swansea, Wales. In 1892 a small electrolytic refinery was established at Wallaroo, the first in Australia, based on principles developed by Elkington at Pembrey, Wales in 1869. The Wallaroo refinery was specifically built to recover gold and silver from copper produced by smelting gold-containing feed materials shipped from Western Australia. This first venture into electrolytic refining was replaced in 1903 by a somewhat larger refinery which, although modest in size for its time, with a capacity of about 1000 tonnes of cathode copper per year, was very productive in precious metals. Anode copper was produced by an updated version of the reverberatory-based Welsh process until 1910 when barrel-type pneumatic converters were introduced based on American practice; subsequently, anodes were cast by tapping the precious-metals rich "bottoms" portion of converter copper as produced at about one-fifth into the copper blow. The present paper describes the Wallaroo refinery, its anode supply and products, supported by initial observations on a sample of a Wallaroo cathode held in the collection of the South Australia Museum, Adelaide SA, Australia. INTRODUCTION Australia ranked 6th in the world for copper mine production in 2018, with an output of 918,000 tonnes of mined copper, after Chile, Peru, Congo, China and the USA; about 40% of Australian mined copper was smelted in the country. Interestingly, the world ranking of Australia in mined copper has, with a few variations, remained about the same for more than 100 years – of interest, it was also the 6th largest country for copper production at 21,089 tonnes in 1899. At that time, all or most of the copper was smelted in the country (Mackey, 2016). Copper was first discovered in Australia in 1842 in South Australia not far from Adelaide; additional copper discoveries in the region soon followed. At first, copper ore was shipped to Swansea, Wales for smelting (Bampton, 2003). However, in addition to the long, 150 day one-way sea passage, it seems Welsh smelters preferred higher grade of ores – these aspects and likely a mood in the new colony to be independent of Swansea (Evans, 2014) evidently encouraged local smelting at the mine sites using small, Welsh-type reverberatory furnaces fired with hardwood as fuel and operated by Welsh and Cornish migrants. The first large copper smelter in Australia commenced in 1848 at Bremer, near Callington some 60 km east of Adelaide. With larger discoveries on Yorke Peninsula, the Wallaroo copper smelter at Wallaroo Bay on the west coast of the peninsula commenced operations in 1861 (Bell & McCarthy, 2008). Thus began one of the most successful, and in its day, one of the most advanced and innovative plants in Australia if not the world. In the late 1860s, it was considered one of the largest copper smelters in the world (Bell & McCarthy, 2008)

Jan 1, 2019

By H. J. McQueen

The irregular history of Mg wrought products is briefly described. The temperature and strain rate dependence of microstructural evolution, flow stress and ductility of Mg alloys in hot working, are described. The flow curves rose rapidly to a peak stress which was lower as temperature T rose and strain rate e declined and above 300°C the curves extended into plateaus until failure. Clearly grains not oriented for slip undergo mechanical twinning in the initial stages (a 0.15) at all temperatures. Basal slip proceeds in suitable grains and in the twins. The stress concentrations at grain and twin boundaries lead to slip on non-basal systems and to the formation of subgrains with greater dynamic recovery (DRV) at higher T or lower e. With increasing strain, misorientation builds up resulting in dynamic recrystallization (DRX) first at twin intersections and later at grain boundaries which have become quite serrated. Even after extensive straining at high temperatures, the new grains are found mainly along the boundaries of the original grains, leaving their centers with only basal slip except when nucleation at twins leads to completion of DRX throughout a grain. Despite similar shear modulus and melting point to Al, hot mechanical forming behavior of Mg alloys differ due to differences in crystal slip systems, twinning, and second phases. Moreover, the influences on forming of alloy additions (solutes, segregation in casting, dispersoids, precipitation) and impurities are not as well catalogued as for Al. Despite the benefits from dynamic recrystallization, varied grain orientation effects, heterogeneous substructures and the resulting stress concentrations result in considerably lower ductility for Mg alloys at the same stress level as for Al materials. Application of these theories to extrusion, rolling and forging and the effects on product properties are surveyed.

Jan 1, 2006

By M. Bryson, A. E. Brady, W. Dawes, G. Beer, N. Sehlotho

Mkango Resources Limited is developing the Songwe Hill Rare Earth Element Project in southeast Malawi. Since being awarded the exclusive exploration licence for the project in January 2010, Mkango has completed an extensive work programme including detailed mineralogical studies, geological mapping, geochemical sampling and trenching, environmental and social studies, two phases of diamond drilling, and extensive metallurgical test work. In October 2012, the company announced a NI 43-101 compliant mineral resource estimate comprising an Indicated resource of 13.2 million tonnes grading 1.62% total rare earth oxides (TREO) and an Inferred resource of 18.6 million tonnes grading 1.38% TREO. The Indicated mineral resource estimate formed the basis for commencement of the Preliminary Feasibility Study (PFS). The mineralogical program identified the fluorocarbonate mineral, synchysite, and the phosphate mineral, apatite, as the primary rare earth element (REE) bearing minerals. Extensive flotation testwork conducted at Mintek in South Africa has resulted in an effective regime to increase the REO grade 2.6 times. Initial leaching testwork by Mintek identified that a selective hydrochloric acid (HCl) leach can target the gangue minerals with minimal REE dissolution. Recent testwork undertaken at Nagrom in Western Australia has expanded on this work to develop a two stage HCl leach process incorporating HCl recycling. A downstream processing route of purification and cerium rejection to produce a cerium depleted high grade REE concentrate suitable as feed to a separation facility is proposed.

Jan 1, 2014

By W. W. Cummings

Canada's only current tungsten producer started up in 1962 with a small open-pit mine on the Flat River , 180 air miles north of Watson Lake, Yukon Territory. The orebody was in a contact-metamorphic skarn zone and contained about 1.5 million tons of ore grading an estimated 2.47% W03 and 0.5% copper. Near the end of the open pit , a new zone was discovered on the lower limb of the same structure, and the decision to go underground was made in 1972. The new "E Zone" contains over 4 million tons of ore grading an estimated 1.6% W03 and 0.28% Cu , and has been supplying the concentrator at about 175,0 00 tons/ year since late 1974. A continuing program of change and up-grading is necessary in the conversion from a seasonal open-pit mine with limited life to an underground operation with twenty years of reserves. Changes are necessary in plant and services as well as the mine. Also, environmental protection requirements have changed from rudimentary to rigorous over the life of the operation. This paper sums up the changes in the operation since 1971 and outlines the changes yet to come.

Jan 1, 1977

"Option pricing is used in finance for valuing options to buy (or sell) shares at some future date because it provides a convenient framework for quantifying values subject to uncertainty. As one of the main sources of uncertainty in mining is the price (sales) of the metal, this approach can also be used for valuing mining projects.The first part of this paper reviews options and option pricing; the second part presents the approach developed by Brennan and Schwartz (1985) for using option pricing to value natural resources. Several applications of this methodology have been published; these are described. From a mining point of view, the assumptions made by Brennan and Schwartz are too simplistic. The weaknesses are discussed with a view to improving an apparently promising new way of assessing the value of projects. IntroductionThe collapse of the British merchant banking group, Barings, has highlighted the risks that can be incurred by speculators and arbitragers in the futures and options markets. But this negative attention on futures and options should not make us forget their positive aspects. They can provide producers and consumers of metals with more predictable sales prices. The introduction of the new traded average price options, TAPOS, by the London Metal Exchange in January 1997 is a response to this need. Equally important, the theory that the finance industry has developed for valuing options provides an interesting framework for valuing mineral projects as well. While this paper was being revised, the South African gold mining house, JCI, announced that it was using a methodology based on option pricing for valuing the mineral rights to deeplevel gold resources (see Box 1)."

Jan 1, 1997

By F. O. Verret

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012

By V Dolmage

In 1957 and 1958, ten topographically suitable damsites were investigated along the Peace river between Finlay Forks and Hudson Hope, B.C. Of these, three were eliminated after a reconnaissance survey indicated that the geology was unsuitable for the 650-ft.-high dam contemplated. ?After extensive drilling, five other sites were deemed unfeasible because of geological factors and, in 1959, the two remaining sites were designated as being suitable, one for the high dam and the other for a low dam downstream. The sites are located in the Peace River canyon, on the west and the south? side of Portage mountain, west of Hudson Hope. The site for the large dam, the Portage Mountain dam, has since been investigated by surface mapping, thousands of feet of diamond drilling, a seismic survey, laboratory rock tests and on-site grouting tests in order to establish the possible effect on the dam of all facets of the foundation rocks. Three diversion tunnels, 50 ft. in diameter and 2,200 feet in length, have been driven through massive sandstone and shale, and an intake cut, 500 ft. in length, 200 feet in width and 200 feet in depth, has also been excavated in rock.

Jan 1, 1963

By H. J. McQueen

Friction stir welding (FSW) generates complex microstructures in the nugget and thermomechamically affected zones (TMAZ) that have led to diverse explanations. However, consideration as an extension of microstructure development in piercing/extrusion can lead to a better understanding of flow patterns and microstructures during FSW. Furthermore, the intense strains in the nugget/TMAZ can be interpreted by comparison with ultra-high strains in torsion that exhibit dynamic recovery as extending into regions with high angle boundaries strongly serrated with spacing near the subgrain size defined by the high temperature. The subgrain diameter and extrusion pressure have been shown to be dependent on the Zener-Hollomon parameter Z (=t exp(Q/RT), Q activation energy, R gas constant) combining temperature T and strain rate E in the same mariner as for torsion and compression. Moreover, such tests exhibited steady state stress os above a certain strain Es (rising as Z increases) in which T, , subgrain diameter and dislocation spacing remain constant. Due to the subgrain boundaries (SGB, low angle <5°, i.e.,LAB), continually rearranging by migration, decomposition and reformation, the subgrains remain equiaxed in elongating grains, whose boundaries (GB) become serrated as they migrate to absorb SGB. As confirmed by straining in torsion at constant T and Z. , more subgrains bordering the greater GB area have several high-angle facets (HAB) ; these small cellular regions with a mixture of HAB and LAB facets are designated HAB-subgrains. As serrations in neighboring grain boundaries impinge, the grains pinch off becoming shorter; this occurs at higher strains as subgrain size decreases with rising Z. The pinching-off makes the neighbors thicker so the grains never become thinner than about two subgrain diameters. In conjunction with such geometric dynamic recrystallization (gDRX), GB&apos;s undergo a net migration into grains with denser substructure, enlarging those with larger subgrains. Consequently a better name has been proposed: grain dimensioning dynamic recovery (gDRV).

Jan 1, 2007

By R. D. Brown

In his March 31, 1977 budget, Finance Minister Macdonald has attempted the delicate balancing act of stimulating the economy without reinforcing the inflationary pressures which Canada is continuing to experience. Several tax changes of benefit to the mining industry, as well as measures designed to encourage oil exploration in frontier areas, are among the budget proposals. Additional earned depletion of 66- 2 /3 %, which may be offset against income from any source, will be available on drilling costs in excess of $5 million incurred between March 31, 1977 and April 1, 1980 in connection with an exploratory well in Canada, including the continental shelf . Other changes include more favourable treatment of resource property dispositions, less restrictive rules r elating to "successor corporations" , increased capital-cost allowance on railway spur lines, the inclusion of certain production royalties in Canadian development expenses and the application of the lower "manufacturing and processing" tax rate to sulphur production. To encourage business capital spending, the 5% federal investment tax credit it to be extended an additional three years to mid 1980 and broadened to include spending on scientific research and development. The rate of credit will also be selectively increased on a regional basis, to 7.5 % in certain designated areas in Saskatchewan, Manitoba. Northern. Ontario and Quebec, and to 10% in the Atlantic provinces and the Gaspe.

Jan 1, 1977

By P. D. R. Maltby

"The Canadian Institute of Mining and Metallurgy has undertaken to host the XIV International Mineral Processing Congress to be held in Toronto at the Royal York Hotel from October 10 to 16, 1982. The theme of the Congress will be ""Worldwide Industrial Application of Mineral Processing Technology."" The program will include 10 sessions and numerous field trips to the different mining areas of Canada.For prospective authors, the preliminary program includes sessions on,1. Flotation - plant practice, equipment design, simulation, control and economics.2. Comminution - plant practice, equipment, design, simulation, control, wear, energy consideration and economics.3. Round table seminar on large grinding mills.4. Round table seminar on modern and future plant design.5. Mineral processes to recover precious metals.6. Mineral processes to recover energy minerals (coal, uranium).7. Mineral processes to recover industrial minerals.8. Round table seminar on the environment and ecology and how the different countries cope with associated problems.9. Materials handling with an emphasis on agglomeration techniques ereconentration methods, solid-liquid separation.10. Open session to deal with topic emerging from general demand."

Jan 1, 1980

By Magella Pelletier

"IntroductionDepuis une vingtaine d&apos;année, les nombreux travaux de géochimie effectués par l&apos;industrie privée et les milieux gouvemementaux ont permis:• de découvrir de nombreuses zones minéralisées a valeur économique;• d&apos;identifier et de vérifier certains patrons de dispersion géochimique au-dessu s de secteurs minéralises déjà connus;• de favoriser le développernent des techniques analytiques;• de forcer le développement d&apos;une mise en carte des résultats d&apos;analyse, qui soit plus adéquat afin de permettre une meilleure interprétation géochimique.L&apos;une de ces cartes géochimiques qui permet le mieux de mettre en valeur les données analytiques et qui fut instaurée au debut des années 80, est la carte d&apos;interprétation géochimique par pondération.Cette carte numérique semi-quantitative, qui est construite à partir des données de base et de l&apos;importance des éléments indicateurs pour une substance donnée, permet d&apos;identifier et de définir des zones possédants de fortes probabilités pour la recherché de sources minéralisées."

Jan 1, 1987

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By N. A. Jabit

The dissolution behaviour of ilmenite in acid solutions has been studied by many researchers to improve the leaching efficiency. Most studies which utilized natural ilmenite from different origins resulted in different reactivity due to the alteration caused by the weathering process. Previous researchers have suggested that the greater reactivity shown by some ilmenite samples towards sulphuric acid may be a result of the mineral being relatively unaltered. In the present study a rotating synthetic ilmenite disc of 2.2 cm diameter was subjected to leaching studies in hydrochloric acid. The dissolution rates of iron and titanium from synthetic ilmenite were determined in hydrochloric acid solutions (4 M to 9 M) over a temperature range of 50 to 80°C. Results show that the rate of dissolution of both iron and titanium increased with the increase in acid concentration. However, the rates decreased with time and obeyed a parabolic rate law indicating the blockage of the surface by an insoluble product. The rates of dissolution of both iron and titanium were higher in the presence of SnCl2 and remained unaffected with time indicating the reductive role of SnCl2 which inhibits the formation of surface blocking solids. Application to natural ilmenite is also discussed.

Jan 1, 2014