Search Documents

The goal of this presentation is to firstly, review mine effluent permits in a number of regulatory jurisdictions; and secondly, to develop a strategy for incorporating the regulatory requirements into the environmental assessment (EA) process for new mine proposals. The focus was on the province of British Columbia (BC) and their recent initiative on the One Project, One Process initiative. This task was approached by reviewing mine effluent permits for various regulatory jurisdictions and comparing them to BC mine effluent permits. This comparison revealed a variety of approaches for designing mine effluent permits, but there is a common scientific approach, which supports the conclusion that the permitting of mine site discharges can be designed based on a scientific approach. This approach is expected to: (a) achieve sound environmental protection, (b) demonstrate the application of Best Achievable Technology, (c) incorporate sound sustainability approaches, (d) incorporate regulatory objectives, and (e) create efficiencies for the regulator and mining industry. There is an essential precursor to developing a sciencebased effluent permit for which the proponent must provide: (1) the necessary technical assessment information to demonstrate the mine effluent permit application will result in an environmentally protective effluent discharge, to the satisfaction of the permitting agency; (2) the necessary level of detail for essential mitigation pollution control works to demonstrate how they will be operated to achieve the necessary treatment goals; (3) the necessary level of detail for non-treatment mitigation (passive treatment, or passive pollution control); and (4) the necessary level of detail to demonstrate how pollutants will be prevented from being mobilized (or being generated) from ore and waste materials, or, if the pollutant originates from an added milling reagent, how the reagent will be reduced. While (active) mitigation pollution control equipment is more definable in an effluent permit, non-treatment mitigation is more nebulous in terms of defining in a mine effluent permit; it is therefore recommended that appropriate management plans be developed for essential mitigation pollution control and non-treatment mitigation (passive treatment) and submitted with the proponent?s EA/effluent permit application packages. Major deficits in adequate active and passive pollution control will inevitably lead to regulatory impediments to developing a permit and allowing a mine to be developed, although EA processes strive to preclude major permit information gaps; the onus is on the proponent to provide complete information in this area. Hence the importance of EA processes ensuring that the major technical information requirements for effluent permit development are included in the EA phase. Recently, this aspect of the mine EA process has taken on a new role under the political efforts of One Project, One Review Process (Canadian) and One Project, One Process (in BC). These initiatives translate, in part, to ?synchronous permitting? (in BC): effluent permitting, for example, may be initiated shortly after the proponent submits the EA application to Ministry of Environment.

Aug 1, 2013

By H. F. Zurbrigg

Introdduction The main line of ascent in the development of the nickel industry may be traced back through the International Nickel Company of Canada, Limited, to its earliest antecedents, the Canadian Copper Company and the Orford Copper Company. Mining geology is but one aspect of the overall development of this organization, and the stress it has placed on geology grew according to the need. In the early days, intensive geology was not required because ore supply was not one of the main problems of this or any of the pioneer companies. The difficulty then was to find economic methods for reducing the ores to nickel and copper, and markets for absorbing nickel in the face of a limited demand from consumers heavily prejudiced in favour of the New Caledonia product. "Very early in the history of the region it was patent to everyone that to share in the full benefits of the industry the same individuals or company must control the whole of the operation necessary to manufacture the finished product' (1, p. 45). These conditions were fulfilled for the International Nickel Company in 1902 when the Canadian Copper Company (incorporated 1886), with its ample ore supply, took the initiative to merge its interests with those of the Orford Copper (Refining) Company (incorporated 1887) to form the new company which, with reorganizational changes, emerged as the producer of the overwhelming bulk of the world's nickel. The Mond Nickel Company, Limited, entered the field in 1899 with a refining process, and over a period of years acquired ore through purchase of mining properties. This Company operated successfully and independently until 1929 when its assets were joined with those of the International Nickel Company in order to permit the most economic exploitation of the Frood-Stobie orebody in which both Companies were interested.

Jan 1, 1948

By F. K. McKean

Abstract A discussion of the difficulties involved in the production of a clean molybdenite concentrate introduces the paper. There is a brief description of the various methods for producing molybdenite that will fit marketing specifications, and it is shown how these methods are nor suited to the milling of ores containing small quantities of bismuth and copper. A process that was developed in the ore testing laboratories of the Bureau of Mines at Ottawa for the La Corne mill of the Molybdenite Corporation of Canada is described in derail and some results from pilot plant operation of this milling scheme are tabulated. A description of the La Corne mill, where the writer supervised the introduction of the process on a commercial scale, adds to the interest of the paper. In conclusion, there is a review of the conditions necessary for proper operation of the flowsheet. An attempt is made to show how the process might be satisfactory in other problems similar to that at the La Corne mill. Introduction The production of a molybdenite concentrate, free from impurities and high in grade, has been a difficult task when milling some types of ore. Whereas ordinary flotation techniques will produce acceptable concentrates of the baser sulphides, in many cases they will not serve in the treatment of molybdenite, for this mineral must be of optimum grade and purity to bring the best prices, or to find a market at all . Faced with the necessity of meeting stringent specifications, the mill operator has been forced to employ expensive processing methods, and to be satisfied with low recoveries, in order to make grade with his product. The most objectionable and common impurities found with molybdenite are: (a) gangue minerals and iron sulphides, which lower the grade; and (b) copper, bismuth, or antimony, which are deleterious in the final uses of the molybdenite products. It is difficult, and sometimes impossible, to market a concentrate with over 0.5 per cent of any of the latter impurities, or with a grade much below 90 per cent MoS2. Various methods, which have been highly successful in specific applications, have been developed to meet the problem of producing a suitable concentrate. All of them, however, have certain defects precluding their use when treating ores of a nature different from the one for which they ? were designed. The writer has developed a process for molybdenite ores having an objectionable impurity content. A description of the procedure involved, and of the La Corne mill of the Molybdenite Corporation of Canada, where the process has been adopted, should be of interest to flotation operators.

Jan 1, 1947

By Jason Berenyi

Presentation Overview ? What is Potash? ? Where are the potash deposits? ? Current potash mines ? production, capacity and planned upgrades ? Saskatchewan Saskatchewan?s Potash Production Potential s ? Current Status of Potash Exploration ? Increasing Demand for Potash ? Saskatchewan global role

May 1, 2009

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By W. E. Segsworth

Introduction By far the largest part of the money raised for mining is raised by honest and legitimate means; but a not inconsiderable amount is raised by fraudulent sales methods. It will be conceded without argument that the greatest menace to the mining business is the fraudulent promoter. The sale of worthless mining stocks to the public by high-pressure. salesmen, house to house canvassers, telephone campaigns, fraudulent use of the mails, fraudulent statements, and reloading, has seriously prejudiced the public against even legitimate mining. A very small percentage of the funds raised by such fraudulent means is ever spent on the property, but instead is absorbed by the promoter in illegitimate' profits, enormous commissions, high office rents, and other expenditures, and is just so much subtracted from the fund which the legitimate developer needs to bring new mines to the point of production. The mining fraternity has been at fault in that, while they recognized this situation, they made no adequate attempt to rectify it. They knew that these fraudulent practises were conducted by parasites who attached themselves to the mining business in boom times and claimed to be part and parcel of it, but who were merely professional salesmen and promoters who, when there was not a mining boom, were selling sky-line real-estate, worthless oil stocks, or fraudulent securities which happened to be popular with the public. While mining people had this distinction well in mind, the public did not differentiate between the crooked promoter temporarily selling fraudulent mining stock and the honest promoter who made mining finance his life work; and we did little to make this distinction clear to the public or to sweep these money grabbers out of our house. The historic boom of 1927-8 and '29 brought with it the usual crop of crooked mining promoters, and the scandals resulting from their operations forced the Governments into the enactment of laws to attempt to protect the gullible public against the operations of these meanest of thieves and to appease public clamour.

Jan 1, 1934

By L. E. Djingheuzian

IN 1953, Lewis (1) published an article which brought forth a great amount of discussion by grinding engineers. In his contribution to discussion the present writer (2) suggested that, for the most efficient performance of a ball mill, there must be a .definite relationship between Cn, per cent critical speed, and V p, per cent mill volume occupied by the ball charge. Later, he ( 3) was able to publish some grinding data from Wright-Hargreaves milly which appeared to bear out this contention. It is with this view to establishing a fundamental relationship between Cn and Vp that the idea of this Forum was conceived. Accordingly, a questionnaire was prepared and copies of it were mailed to over eighty Canadian mill operators. This questionnaire did not include a question on dilution on the assumption that each mill operator was using the most efficient dilution for his operation, nor was a question on efficiency of classification included since it was thought that the inclusion of efficiency of dassification in the questionnaire at this preliminary stage might render the forum discussion,. while everybody was trying to find his bearings, too unwieldy. However, it is evident that, as discussions develop, this forum will have to define a uniform method for establishing most efficient classification in grinding circuits

Jan 1, 1957

By P. Bramwell, R. Tremblay

"The Port Radium leaching plant of Eldorado Mining and Refining, Limited, produces 450 t./d. of sulphuric acid leach liquor containing l. 73 g. /I. U 308. After solvent extraction, the waste solution is discarded at 0.002 g./l. U30s for a recovery of 99.8 to 99.9 per cent. The solvent is acidified with weak sulphuric acid, loaded to 4.5 g./l. U80:1 in three-stage extraction, scrubbed with water, and stripped with soda-ash solution in single-stage stripping. Caustic removes the UaOs from the pregnant strip solution as a precipitate. The slurry is filtered, re-pulped with water, and re-filtered. The pressed precipitate at 81 to 82 per cent equivalent U30s is dried and packaged. The carbon-ate filtrate is cooled to remove sodium sulphate build-up and carbonated to convert excess caustic. Reagent consumptions are 4.1, 0.22, and 0.39 pounds per 1,000 gallons of pregnant solution for Diesel oil, amine, and alcohol, respectively. Caustic consumption averages 1.3 to 1.4 pounds per pound U3O8.Extraction and stripping is accomplished in sheet-iron mixer-settlers lined with Phenoline. Piping on both circuits is Schedule 80 polyvinyl chloride. Valves are straightway Buna N lined with American Hycar diaphagms. Extensive instrumentation ensures good metallurgy with a minimum of variations and labour. Mixing in a continuous organic medium and careful acidity control are required to minimize third-phase formations. Heating the precipitate slurry is conducive to good filtering in Perrin presses with neoprene-coated, rolled-steel sectors. Sodium sulphate is crystallized from carbonate filtrate solution by batchwise cooling to 54°F. with lake water."

Jan 1, 1959

By H. B. Merlin

"The past demands for energy and the contributions by the major sources are shown for the world and regions, and for Canada. Three forecasts of future demand are presented. By the year 2000, the world will be consuming energy at a rate of 670-700 x 1015 Btu/year. Canada's rate is estimated at 20 x 1015 Btu/year. Electricity will increase its portion of energy from 7.5 per cent to 15 per cent, and more than 40 per cent of the primary energy w1ll. be required to generate 1t. World, regional and Canad1an forecasts are g1ven for total electricity generated and for electricity generated in nuclear stations. The integral world requirement for energy by the year 2000 will be over 12 x 10 18 Btu. Current recoverable fossil and hydro reserves are about 18 x 1018 Btu. The total reserves are estimated to be seven times greater.World production of electricity in nuclear stations by the year 2000 will be almost three times the electricity produced in the world today. The amount of fuel consumed in generating this electricity will depend upon the types and mix of reactors installed. The heavy water reactors, alone or in conjunction with fast breeders and liquid fuel reactors, are the most efficient users of uranium and thorium resources. The heavy water reactors are also the most efficient producers of plutonium which will be required as fuel for fast breeders."

Jan 1, 1969

By Marc Symbaluk

Core Programs Current ? Aboriginal Involvement Program ? Adaptive Forest Management / Forest History Program ? Grizzly Bear Research Program ? Natural Disturbance Program ? Foothills Growth and Yield Association ? Foothills Stream Crossing Program ? Fish and Watershed Program ? Caribou Landscape Management Association ? Social Science Program ? Local Level Indicators Program ? Communications and Extension Program ? Geographic Information Systems Program ? Mountain Pine Beetle Ecology Program In Development ? Climate Change Program ? Forest Community Program ? Water, Quantity and Quality Program (Water for Life) ? Circumboreal Initiative ? Yellowhead Ecosystem Management Group

May 1, 2008

By E. D. Fox

Introduction The financial statement of the hypothetical Gold Mining Company, which forms the background of this survey, was designed for the Institute with the express abject of having it assessed in respect to Profits by the several taxing bodies representing the Federal and Provincial Governments, which comprise the Dominion of Canada. On the completion of the figures, copies were sent to the several Ministers of Mines, accompanied by a request that they be submitted to their taxing authorities and assessed accordingly. The response, while it was not general, was very favourable, and at all times we were treated with the utmost courtesy and patience, and what has been set forth in the compilation bears the authentication of the various government officials who are immediately concerned with taxation. The data itself constitutes a fairly comprehensive digest of taxation as it directly applies to gold mining profits in Canada. The Hypothetical Balance-Sheet (See Exhibit A) In the balance-sheet schedules 1 and 2 (Exhibit A), income is divided between taxable and non-taxable classifications, and here it should be noted that the division contemplates only the assessment for Dominion income tax. The same applies to the factors of exchange and depletion. Therefore, in making comparisons, it is to be borne in mind that the set-up for assessment to the Provinces, that is, Manitoba and Alberta, will stand as if the gross non-operating income is taxable, with the reservations as shown in the notes below the schedules.

Jan 1, 1934

By B. W. Clyburn

"Coals from the Corporation's Lingan and No. 26 mines are classified as high-volatile A bituminous, with a very low inherent ash and containing all essential properties to provide metallurgical coal, with the exception of a high sulphur content. Only through proper cleaning at low specific gravity can the pyritic sulphur fraction of the coal be liberated to an extent where final sulphur meets coking standards. This first section of the paper deals with the operation of a Dutch State Mines heavy-media cyclone circuit to achieve an actual separation in the region of 1.30 specific gravity. A discussion of the parameter of control which must be applied along with an appraisal of the results obtained is included in the paper.Introduction Very high fluidity and unusually low ash are the outstanding characteristics of coal from Devco's mines in the Harbour seam of the Sydney coal field. However, sulphur content, mainly pyritic, ranges from 1 to 2.50Jo. To obtain the low and consistent sulphur level required in metallurgical coking coals, preparation at low specific gravity is required. Metallurgical coke is used as the fuel in an iron blast furnace. Its sulphur content largely determines the quantity of slag required to remove it and therefore influences furnace productivity and unit costs. Typical data on the various coal properties of importance in the production of coke are included in Table 1."

Jan 1, 1985

By D. C. Carter

"The Nova Scotia Department of Mines and Energy located a drillhole at Riverside Corner, Hants County, Nova Scotia, to examine the stratigraphy, structure and potash potential of the Kennetcook River gravity low. This evaporite-related gravity anomaly is one of the largest virtually unexplored gravity anomalies in Nova Scotia. The drillhole intersected a structurally complex sequence o flower Windsor Group ('B' Subzone) evaporites. Downhole geophysical wireline logs were used, in conjunction with detailed lithological descriptions, to interpret the structure and stratigraphy of the sequence. Similar application of total gamma ray, density, caliper and neutron-neutron log responses allows stratigraphic correlation of Windsor Group carbonate marker units separated by up to 35 km in Cape Breton. This work confirms the value of downhole geophysical logs as a tool in the exploration of evaporite deposits regardless of the presence or absence of high quality core. INTRODUCTIONThe exploration methodology for evaporite (specifically salt/potash) deposits in eastern Canada (and worldwide) is relatively simple: identify a negative gravity anomaly within a favourable geological setting, Windsor/Cordroy Group sediments in eastern Canada, and drill it (Anderle, 1980). Although this is an obvious oversimplification of the necessary expertise in the planning and complet ion of an exploration program, those familiar with potash exploration drilling can attest to the risks and expense, in terms of time and problems , associated with the location and drilling of diamond-drill wildcat holes. Potash exploration programs in eastern Canada, their results and inherent difficulties, have been documented by Anderle et al. (1979), Cooper (1981), Dekker (1982), Carter and Boehner (1986), Carter (1988) and Carter and Anderle (in prep .).Downhole geophysical wireline logs have become an important tool in the stratigraphic and structural interpretation of evaporite sequences in eastern Canada and, in many cases, represent the only information recovered or the only information available due to the drilling method (rotary) and/or the long term instability of evaporite cores. This paper documents examples of downhole geophysical log responses which, combined with detailed lithological examination of drill core, or in the absence of core, are used in the interpretation of the complex lithology and structure of a deformed evaporite deposit. Geological and geophysical data from the Nova Scotia Department of Mines and Energy (NSDME) Riverside Corner 85-1 drillhole are presented here as a partial case history and prime example of the use of this method to interpret the complex structure of an evaporite deposit. Drilling of NSDME Riverside Comer 85-1 was conducted in late 1985and early 1986by the Department (Carter and Boehner, 1986) under a program to assess the potash potential of selected areas of the province as part of the Canada-Nova Scotia Mineral Development Agreement 1985-89. A reinterpretation of a portion of the available data from two exploration drilling projects on Cape Breton Island in the Canso-Bras d'Or area is also presented (see inset, Fig. I). Several drillholes have intersected the Windsor Group evaporite sequence in these areas and the available geophysical logs are a valuable tool in the interpretation of the structure of the deposits. However, no attempt has been made to present or discuss the detailed geological investigation and comparison of these two deposits. They are presented here as an example of the reinterpretation of existing data and their application to stratigraphic correlation and structural interpretation of complex evaporite deposits. Further work is necessary to document the stratigraphic and structural correlation of these two areas."

Jan 1, 1989

By W. L. Ott, J. E. Hawley, C. L. Lewis

"IntroductionTHE APPLICATION of spectrochemical analysis to metals of the platinum group was advocated by Harvey (3) as follows: ""The spectra of the platinum group metals have been studied less than many of the more common metals. The rarity of occurrence of these elements makes the analysis relatively unusual. Potentially, the analysis of this group is an excellent application of spectrographic methods, particularly in contrast to the tedious chemical procedure"".Wichers (8) divides platinum-metal analysis into three broad divisions as follows :( 1) The detection and estimation of these metals in other materials, e.g., ores, where the amounts present are very small.(2) The detection and estimation of impurities in the refined metals themselves ....(3) The analysis of alloys of the platinum metals .....The present paper deals with the second division: analysis of refined rhodium.Research on spectrochemical techniques for determination of trace contaminants in refined platinum metals was begun at Queen's University in 1949, under the supervision of Professor J. E. Hawley. Since 1953, the work has been continued in the Metallurgical Laboratories of Falconbridge Nickel Mines, Limited. Techniques for spectrochemical analysis of refined platinum and palladium have been published ( 4, 5). A technique for analysis of refined iridium has been developed but not yet published."

Jan 1, 1955

By Sherwin F. Kelly

"THE TITLE I have chosen is certainly not one of those self-explanatory ones. I shall endeavour to make its significance clear during my remarks but, in the hope of minimizing that inevitable exodus which follows a good lunch such as this, I am going to withhold the final key to its meaning until the very last sentence of this talk.Some explanation is due at the beginning, however, so for those of you unfamiliar with Spanish I will explain that casa means house, or home. The casa about which I am going to talk necessitates a wide .and generous interpretation of the word, because I am using it to indicate principally that portion of the North American continent which is the home, in the western hemisphere, of British and American ideals of justice and freedom, the dignity of the individual and his right to exercise private initiative .and engage in private enterprise. In a wider sense, I am including the entire western hemisphere, which may yet stand as the last bulwark of political and industrial democracy.As for the treasures of which I am about to speak, may I remind you that there are no• material treasures but those derived from the earth, and they are derived by one of two processes, -mining and farming. These two fundamental industries are the basis, and the sole material basis, of our welfare, our wealth, our very existence. From farming, whether it be farming of the land. or farming of the sea, we obtain the food to keep us alive, healthy and able to work."

Jan 1, 1955

By R. E. Eyre, L. P. Landucci

C URRENT practice in the zinc concentrate roasting plant of The Consolidated Mining arid Smelting Company of Canada Limited, at Trail, B.C., involves passing the furnace effluent gases through an electrostatic precipitator for the recovery of dust. After removal of the dust the gas is treated for recovery of sulphur dioxide by conversion into sulphuric acid ( 1). However. as roasting techniques improved, and furnace productivity in-creased, the rated capacity of the precipitator was exceeded and it was necessary to consider various means of improving the dust recovery. A study of methods indicated that a baghouse using silicone-treated glass fabric, might be suitable for this particular application. Glass fabric was chosen because the temperature of the roaster effluent gases would range from 450°F to 500°F and tempering air was undesirable to avoid dilution of the sulphur dioxide gas.

Jan 1, 1962

By Douglas A. Grieg

THE EXCUSE for producing still another paper dealing with the oilfields of the Middle East is the overwhelming importance of this area to everyone, both inside and out of the oil industry. Figure 1 shows the area defined as the Middle East for the purpose of this paper. No description of what constitutes the Middle East is generally acceptable to everyone and, in fact, in many parts of the world it is referred to as "Western Asia". At the time ?the writer went to work as a geologist in the Middle East -this was in 1926 -there were just three known oilfields, namely, Hurghada in Egypt, Naft Khaneh in the Transferred Territories of Iraq, and Masjid-i-Sulai-man in Persia. Their combined producing rate at that time was around 100,000 barrels per day. Toda y, just thirty years later, some forty-two fields have been proven to exist, and a recent discovery in Syria -if commercial -may add one more to the list. Producing rates at the end of last year ( 1956) were approaching four million barrels per day. This sizable figure re presents nearly 23 per cent of the total Free World's production. What is more important still, something over 70 per cent of the Free World's proven oil reserves are known to exist in the subsoil of the Middle East.

Jan 1, 1957

By Steven R. McCutcheon

ABSTRACT - The Bathurst-Newcastle district, a subcircular area approximately 50 km in diameter, contains 37 massive-sulfide Zn-Pb-Cu deposits that have defined tonnages, and has 58 additional significant occurrences. The largest deposit is Brunswick No . 12, with total reserves (including past production) of 148 million tonnes grading about 12.50% combined Pb-Zn. The deposits/ occurrences are spatially associated with a felsic volcanic pile that contains a significant sedimentary component. In the vicinity of the Brunswick deposits the pile is divisible into lower and upper sequences. The lower is characterized by megacrystic rhyolite (QFAS) and coarse- to fine-grained quartz ( ± feldspar) wackes and/or tuffites (QAS); the upper sequence is characterized by aphyric to sparsely porphyritic rhyolites (HWR), micro-breccias, and acid hyaloclastites with interbedded dark gray sedimentary rocks. A greenish gray to dark gray siltstone (GGS) separates the two sequences and hosts the sulfide deposits. Lithogeochemistry of !east altered samples shows that the QFAS and HWR have an igneous character, whereas the QAS and GGS have a sedimentary sig­ nature. The two types can be distinguished on the basis of total alkalies (Na2O + K2O) versus SiO2/Al2O3, and Ti02 versus Fe/(Fe+ Mg). Some trace elements, such as Sr and Y, also help differentiate the two types. The QFAS differs from HWR by having higher La/Yb ratios but lower Zr and Th. The Bathurst deposits do not show a close spatial association with rhyolites but rather are stratiform bodies (lacking clastic textures) within fine-grained sedimentary rocks. The scarcity of barite and other sulfates indicates that there was little mixing between the metal­ bearing fluids and cold seawater. High Fe/(Fe+ Mg) ratios in chlorites also indicate the fluids did not contain a significant seawater component. These features and the large size of many deposits suggest that the deposits formed from metal-rich pore waters that were released catastrophically from an acquifer in the footwall stratigraphy.

Jan 1, 1992

By John Drew Ridge

"Over the years, ore geologists have made innumerable observations as to the relationships of certain kinds of ore deposits to particular types of rocks and to the types of primary and secondary structures that these rocks contain. On the basis of these, the places in which to look for new are deposits are more clearly defined than they would be in an exploration program based largely or solely on concepts of ore genesis. This paper discusses the affinity of certain rock types and structures for such ore deposits as: (1) tin-tungsten associated with granitoid rocks; (2) lead-zinc of simple mineralogy in carbonate rocks; (3) massive base-metal sulphides in sedimentary or volcanic rocks; (4) massive base-metal sulphides and oxides at, or near, contacts with igneous rocks; (5) gold or gold-uranium in, or adjacent to, conglomerates; (6) shale- or sandstone-hosted copper; and (7) porphyry coppers. Additional varieties could be considered, but it appears that these examples are sufficient to demonstrate the validity of the suggestion that the use of observational characteristics is far more useful in mineral exploration than that of theories of ore genesis.As by-products of the theory of plate tectonics, many concepts have been put forward to explain how ore deposits of different kinds have been formed. Most, if not all, of these theories seem to be as valid as present-day information permits. However, do these ideas add to the ability of the ore geologist to find ore deposits? I doubt it, and offer reasons as to why I think so.To produce maximum results in any exploration program, the one that makes the greatest use of information produced about the geologic environment of the area being investigated is the one that will provide the greatest return in deposits found for the sponsors of the program. Such exploration is best designated as total exploration, and it certainly is the most effective way of uncovering such new deposits as may exist in the area being studied in particular and of adding to the sum total of nonfuel minerals deposits available to the industrial world in general."

Jan 1, 1983

By A. L. Nunes, J. R. E. Garcia, G. Silva, U. Prasad, C. Rabe

"Drilling through the Guayabal shales, a gray calcareous shale, and the C1 to C100 formations, a well-cemented calcareous-sandstone in Corralillo field, Mexico, is a challenge due to severe wellbore instability problems. Additionally, there has been a history of ineffective reservoir stimulations by hydraulic fracturing. To predict and mitigate these subsurface issues, it is essential to characterize the mechanical properties and rocks strength for a better prediction of borehole stresses and collapse pressure during drilling. Various correlations can be used to estimate and/or determine the unconfined compressive strength but most of them are based on transit time and porosity.In this study, grain size distribution was combined with acoustic travel time, porosity and static Young’s modulus to develop a rock strength prediction model for the turbiditic sandstones of the Chicontepec basin. The main reason this combination of parameters was employed was because of the wide variations in rock strength estimated using traditional porosity-based correlations such as the McNally’s (1987), GMI-Jizba-E’s and Bradford’s (Bradford et al., 1987).To develop a new correlation, a geomechanical and microstructural campaign was initiated. Mineralogy by X-ray diffraction, pore and grain sizes by petrography, clay distribution by SEM and porosity by mercury intrusion porosimetry were measured. Static and dynamic Young’s moduli and Poisson’s ratios were acquired by triaxial and ultrasonic measurements on undisturbed sandstone samples from the Chicontepec basin. More than ten offset wells with wireline data, including transit time, porosity, density, resistivity and gamma ray, were used for reservoir and geomechanical characterizations.Our analyses lead us to propose a new correlation for predicting the uniaxial compressive strength (UCS) of sandstones of the Chicontepec Basin as a function of transit time and grain diameter, both of which can be derived independently from destructive laboratory tests. Our results also highlight the importance and value adding of a combined approach incorporating grain size analysis in the rock strength prediction. The UCS predicted using the transit-time and grain-size-based model presents a median value (P50) of 76 MPa, P10 of 55 MPa and P90 of 89 MPa."

Jan 1, 2015