Search Documents

By M S. El Salmawy

In order to develop the HF-free flotation reagent system, the main objective of this investigation was to study the possibility of separation of quartz from feldspar using non-ionic surfactants as the collector. The non-ionic surfactants used were polyoxyethyl cethyl ether (PECE) and polyethylene glycol monocethyl ether (PGME). The flotation behaviour of quartz and microcline with PECE and PGME was investigated. Each surfactant was a good selective collector for quartz with its recovery being influenced by pH and surfactant concentration. Quartz is floated favourably by both types of polyoxyethylene non-ionic surfactant whereas microcline was not so much. The floatability of quartz increases as the oxyethylene length of surfactants increases. Zeta potential measurements in the system of PGME/mineral were also carried out. It was determined that in the absence of PGME the points of zero charge for quartz and microcline should be approximately at pH 2.5 and 1.8, respectively. The addition of PGME to the system causes both minerals to become less negatively charged. Differences in the zeta potential value between quartz and microcline, in the presence of PGME, were detected. It can be suggested that the interaction of the oxyethylene group to the microcline surface should not be as strong as that to the quartz surface. In the mixed surfactant system of PGME and dodecylamine acetate (DAA), a small addition of DAA causes drastic enhancement of quartz flotation in the wide pH range of 1 ~ 10. In the mixed surfactant system selective flotation of quartz from microcline would be anticipated at pH

Jan 1, 2005

In a previous paper in these Proceedings(l) it was shown from a study of the bore'logs and analyses then available, that the brown coal seams of the Latrobe Valley areas show progressive changes in composition with increase of stratigraphic depth, equivalent to a rise in rank: These changes appear as:(i) An increase in ultimate carbon and hydrogen, calculated on a dry, ash-free basis, and(ii) An increase in calorific value, calculated on the, same basis, each of the order of 1% per 100 ft. of depth, and(iii) A decrease in moisture content of the order of 0.5% to 1.0% per 100 ft. of depth. The decrease in moisture content was found to be less regular than the other changes. In some bores the moisture content remained more or less constant throughout a single seam, or fluctuated slightly, decreasing stepwise on passage to the seam below.It was noted that individual analyses within a bore showed irregular fluctuations, tending to mask the general trend in composition change. This was particularly so for the moisture content, which had been determined for 10 ft. lengths of core, whereas the other components were determined for 50 ft. lengths of core. Averaging of the moisture contents over 50 ft. lengths reduced the masking effects of these irregularities. The suggestion was made that these irregularities arose from variations in the relative proportions of pollen, resin, wood (lignite) and woody attritus composing the core. Such variation in the coal seams has since been established in some detail for the...

Jan 1, 1948

Iron from the blast furnace constitutes the starting point in steel production and any increase that can be made in iron production will bring about important repercussions in a long line of processes. Coke constitutes a major item in furnace operation and consumption at the Port Kembla Works of Australian Iron & Steel Ltd. has been approximately 1,850 lb. per ton of iron produced on ore practice, or 3,000 tons per day.For many years coke quality has been subject to much criticism by furnace operators throughout the world, sometimes with little real grounds. Whatever the merits of previous arguments, and they were no doubt two-sided, the development of bigger furnaces has focused attention on coke strength. At the same time a decrease in the quantity of good quality coking coals available to many plants has stimulated research in this field.Extensive coke research has been carried out overseas, and in Australia the.B.H.P. Organization is now actively doing likewise in its Central Research Laboratories at Shortland near Newcastle, N.S.W., and works research groups at Newcastle and Port Kembla Steelworks. Similar work has been initiated in the beehive coking industry. Such work is in its infancy and this paper will outline the direction of the activities at Port Kembla rather than propound specific solutions.At Port Kembla good quality coking coals are readily available from the IIIawarra coalfield. The seams generally mined for coking are Bulli and Wongawilli and to a much smaller extent Tongarra. Characteristics of these coals appear in Table 1.

Jan 1, 1958

Some attempt to minimise the importance of the greenhouse phenomenon. They do so by observing that global temperatures are still within the range of recent variations and that it is still not possible to predict with any certainty what the precise consequences of greenhouse will be. Both observations are true though the conclusion is dangerous. Ice core samples from the Antarctic and Greenland have established the composition of the atmosphere and global temperature over almost the last 200,000 years. The profile of these twin variables shows that they have moved together; when the concentration of CO2 has been up, the temperature has been up and when the former has been down the temperature has also been down. Over almost 200,000 years the CO2 content has ranged between lows of 190 ppm and highs of 270ppm. In just 200 years of industrialisation the CO2 content of the atmosphere has increased to 350 ppm, 50% higher that the mean of the last 200,000 years and 30% higher than at the start of the industrial age. Carbon dioxide is now increasing at 0.5% p.a. Methane, about twenty times more effective than CO2 as a greenhouse gas has doubled in concentration in the last two centuries and is now increasing at about 1.1% p.a. Methane, nitrous oxide, chlorofluorocarbons together with a number of lesser gases will double the greenhouse effect due to in creased CO2 over the next 40-50 years.

Jan 1, 1989

By Reilly SY, Green TH, O&apos

Alkali feldspar meggacrysts are commonly found (with aluminous clinopyroxene, kaersutitic amphibole, titanomagnetite, ilmenite and apatite, and more rarely with zircon and corundum) in alkalic basalts and their derivatives as discrete crystals and fragments. They are commonly euhedral or subhedral and may be up to 15 cm in size. Their occurrence has been reported from many localities around the world, e.g., Africa, Antarctica, eastern Australia, eastern China, East Fife (Scotland), Eifel (Germany), Massif Central (France), Mongolia, New Zealand, New Mexico (USA) and Siberia (USSR). These megacrysts are relatively homogeneous and belong to the Na-rich anorthoclase group, although Kutolin and Frolova (1970) called them sanidine due to their monoclinic nature. The majority of megacrysts have a molar orthoclase content (Or%) between 20 and 30 (Fig.1). These anorthoclase megacrysts possess a high degree of disorder, with the structural state belonging to the high albite-high sanidine series (Hoffer and Hoffer, 1973; Chapman, 1976).Published interpretations of the origin of anorthoclase megacrysts fall into the following two categories: either (1) Anorthoclase together with the associated pyroxene and amphibole crystallized from basaltic magmas as phenocrysts (cumulate phases) at high pressure and the present host basaltic rocks are the parent magmas for the anorthoclase megacrysts (Binns,l969; Binns et al. 1970; Kutolin and Frolova, 1970; Hoffer and Hoffer, 1973; Laughlin et al. 1974); or (2) Anorthoclase probably crystallized from a more evolved liquid at relatively lower pressure and was then picked up and carried to the surface by a later

Jan 1, 1990

By Fulton E, Ring RJ, Waters DJ

Laboratory leach tests of Nabarlek uranium ore carried out by the Australian Atomic Energy Commission to compare the effectiveness of Caro's Acid1 (permonosulphuric acid) as an alternative oxident to pyrolusite indicated reduced acid consumption in leaching and lime savings in neutralisation of tailings liquors when using Caro's Acid. Interox Chemicals Pty. Ltd. arranged a plant trial for Caro's Acid at Queensland Mines Nabarlek Plant. The trial confirmed that significant savings in acid and lime can be achieved under plant conditions. Plant operations also demonstrated improved redox potential control was possible using Caro's Acid.

Jan 1, 1978

By Hall T. P, Taylor R. N

Fluid flow in a 1:14 scale water model of the shaft and settler of the Kalgoorlie Nickel flash smelter has been investigated by flow visualisation and numerical modelling. Detailed flow fields through the reaction shaft, settling chamber and uptake are presented for flow rates up to 800 Vm and a number of burner configurations. The predicted flow fields were compared with experimental data obtained from streak photographs and video recordings. The effects of cessation of flow through individual burners and changes in shaft dimensions were also Investigated.

Jan 1, 1992

The mining and resources industry in general has relied on macro separation technologies (greater than 1 micron) through processes which include: ò sedimentation ò flocculation and coagulation screening and filtration ò absorption ò magnetic separation ò chemical leaching and precipitation Essentially, these processes and technologies provide the industry with an effective arsenal to handle most separation requirements to date. Dewatering of solutions is one of the most significant requirements of the resources industry, as practically all mining endeavours use water in their process for leaching, extraction, cooling, dilution or for potable drinking water.

Jan 1, 1989

By Todd W, Stone C

A 3D graphics modelling system has been applied to longhole stope ring design at Z.C. Mines, Broken Hill, NSW. This has been in operation for a four month period (January, 1988). The purpose of this application was to provide computer assistance to mine planning engineers and blasthole design draftsmen for the longhole design process, particularly by: 1. reducing the- volume of tracing, drafting and geometric manipulation which is a significant feature of the manual design process, 2. providing additional design drawings to enhance the conception and implementation of stoping design.

Jan 1, 1988

The paper describes the reasons for developing, specifically in South Africa, dense medium processes to allow baths to operate at low (about 1,35) and high (about 2,0) cut points. Low density processing was developed to meet the demand for low ash coals; high density processing was developed to enable heavily contaminated raw coals, destined to be burned in captive power stations, to be de-shaled without loss of combustibles. The anticipated and actual technical difficulties of operating baths at such density extremes are described, and the results from operating plants outlined.

Jan 1, 1987

By Wright S

The feed to the Cockle Creek Imperial Smelting Furnace consists of mixed Pb/Zn con- centrates and lead sulphate-containing elec- trolytic zinc plant residues. Roasting was investigated as a means of desulphurizing the feed to less than 1%. Laboratory studies showed that two process streams were required in which concentrates containing 20% Pb were roasted separately from the leach residues. The residues along with fume from the roast- ing and a portion of concentrate were desul- phurized by means of the roast reduction reaction. Conditions were defined to give

Jan 1, 1986

By Kovscek P. D, Thimons E. D

The Bureau of Mines equipped a longwall shearer with a water- jet-assisted cutting system and measured dust levels during the cutting of a simulated coal block. The block was cut dry, at a conventional water spray pressure of 1 MPa and with water-jet-assisted cutting pressures ranging from 7 to 40 MPa. At water pressures of 20 MPa and higher, dust concentrations were reduced by as much as 85 % via water-jet-assisted cutting in comparison with conventional water sprays. This reduction was achieved without any increase in the water flow rate.

Jan 1, 1988

By Hansmire WH

The 14.7 km Mt. MacDonald Tunnel beneath Rogers Pass in Canada used both drill-and-blast and machine boring methods. A unique ventilation system provides for diesel operations. The design featured minimum construction support and an unrei.nforced poured concrete lining. The west heading was excavated in a single-stage drill-and-blast operation. The east heading used a TBM top heading with a drill-and-blast keyhole bench. The choice of methods was controlled by varying geology, with up to 1,700 m rock cover. Construction performance and progress are evaluated.

Jan 1, 1987

By Scott IA, Jefferson C, Dipasquale S

This paper describes the use of modelling and simulation techniques in the analysis of the heavy medium plant at the Lead/Zinc Concentrator of Mount Isa Mines Limited. The objective of the study is to determine how to increase heavy medium plant recovery at a higher than current rejection rate in order to achieve the desired throughput through the grinding and flotation sections of the concentrator. Three options were considered: 1. Install smaller aperture preparation on screen to enable the cyclones to be fed finer materials. Install smaller diameter cyclones. 3. Maintain low viscosity medium.

Jan 1, 1987

Portable crushing at Duval Corporation's Sierrita open pit mine has proven both the economics and operability of large, hardrock, portable systems. In-house expertise was utilized to create a system incorporating both operational and maintenance features requested by operating personnel. The monitor/control system involves over 400 channels of information and is based on a DEC 1SI 11/2 microprocessor communicating with seven microprocessor-based data acquisition systems over a 4-wire, multidrop link. The year and one-half successful operation affirms the design philosophy and the hardware/software implementation.

Jan 1, 1985

By Woodlands W. K

A 3D graphics modelling system has been applied to longhole stope ring design at Z.C. Mines, Broken Hill, NSW. This has been in operation for a four month period (January, 1988). The purpose of this application was to provide computer assistance to mine planning engineers and blasthole design draftsmen for the longhole design process, particularly by: 1. reducing the- volume of tracing, drafting and geometric manipulation which is a significant feature of the manual design process, 2. providing additional design drawings to enhance the conception and implementation of stoping design.

Jan 1, 1988

Cut and fillstoping using hydraulically placed mill tailings has become an essential feature of stoping operations in Kalgoorlie. ' Approximately 30 per cent of the total production is currently mined by this method. Fill is prepared by thickening or cycloning and is gravitated or pumped underground. The average pulp density is 70 per cent solids by weight, Recent cost reducing innovations are the use of steel passes, corrugated iron manways, polythene film sealing, and the replacing of vertical cement lined pipes with boreholes. TTTTTI rvr T Trim r l1TT

Jan 1, 1964

The Elgas Underground Storage Facility at Port Botany, Sydney, is the first purpose-built cavern of its kind in Australia and allows large capacity, safe and environmentally benign storage of Liquefied Petroleum Gas (LPG). The facility provides Elgas with the flexibility to source product at competitive prices and will ensure long-term security of supply. Construction has provided Orica Australia, formerly ICI Explosives, with a unique opportunity to provide a bulk explosive delivery system specifically designed to meet the exacting demands of the site (see Figure 1) and of the project.

Jan 1, 1999

By Groudeva VI

The biohydrometallurgy of gold is based on different processes which could be grouped into four main groups (Attia, Litchfield and Vaaler, 1985; Karavaiko et al, 1988; Groudev, 1990): 1. bacterial oxidation of gold-bearing sulphide minerals by chemolithotrophic bacteria to facilitate the subsequent chemical extraction of gold; 2. solubilisation of gold from oxide ores by means of heterotrophic bacteria; 3. recovery of gold from solutions by biosorption; and 4. microbial modifications of the surface of gold-bearing sulphide minerals to improve the subsequent gold concentration by physical dressing methods (eg flotation, oil agglomeration).

Jan 1, 1993

By Smitham J. B, Keast-Jones R

Six Australian coals were selected to determine their potential to produce, ultra low ash (less than 2 per cent) coal by progressive size reduction followed by density separation and/or froth flotation. Density separation in organic liquids is effective in the absence of contaminating liberated mineral matter which can be removed by froth flotation with several cleaning stages. The limit of cleaning of these coals was an ash value of 1 per cent while commercially attractive yields were obtained at 2 - 3 per cent ash depending on the coal.

Jan 1, 1987