Search Documents

Currently all engineering schools face a common problem, an ever expanding technological base which must be presented to students within a fixed time period. Traditionally the programmes of study taken by engineering students destined for employment within the mineral industry include formal instruction in aspects of management to an extent greater than that presented in other engineering disciplines. Providing an adequate coverage of an expanding technological base within a fixed time span can lead to a reduction in the time available for 'non-technical' subjects, such as 'management'. This situation calls for periodic review of course contents and allocations of time. Following consultation with an Advisory Committee representing the mineral industry, mining research establishments, and kindred teaching institutions, the University of Melbourne has revised its mining programme. This programme is offered as an example of how aspects of management such as communications, economics, labor

Jan 1, 1980

By P Lukic

The definition of the working sections that will be used in a mine is usually initially made in the field by the geologist supervising the drilling program. These initial definitions are often made on the basis of rules of thumb such as æcoal less than 30 cm thick cannot be mined separatelyÆ; æpartings more than 30 cm thick will be mined separatelyÆ; and æif a coal seam is less than 50 cm thick and the parting above or below is thicker than the coal, the coal will be wastedÆ. These decisions are also often made based on the requirement for a minimum sample mass for analysis, and the desire to collect data at the minimum resolution to conserve the exploration budget.In many cases the geological models based on this data are produced at a resolution that is inadequate to allow the mining engineer to produce a mine plan that will maximise project value. This problem is generally unrecognised.Where data is collected to a higher level of resolution the subsequent processes employed in the production of geological models and mine plans often discards the inherent value that is hidden in this data. Again this problem is generally unrecognised.This paper highlights this problem and then presents a methodology that ensures that the optimal working section is selected and compares the outcomes of applying this methodology versus adherence to the usual rules of thumb.

Sep 26, 2011

By W J. Haylock, K Wasiel

PX4 Software Pty Ltd is a Brisbane-based company, which specialises in providing tenement management software to mining and exploration teams operating in Australia and several international jurisdictions, including the United States, Africa, and Canada. Whilst the company is experiencing substantial growth due to a demand from both the minerals and mining technology sector, there is a crucial gap in the market for critical minerals, which will be required to achieve the net-zero emissions goal set by the Paris Agreement for 2050. To help understand and address the technology gap identified by the unprecedented demand, PX4 Software undertook the Annual Survey of Technological Transformation in the Exploration Industry. This survey involved interviews with 12 very distinguished subject matter experts in the fields of Geoscience and Geology from across the globe. From this survey, we have defined eight major categories of exploration technologies. Notably, the most transformative of these technologies over the past 65 years falls into the Geophysical Methodology category, specifically focusing on image and signal processing of both airborne and downhole data. Advances in computing power during this period have significantly improved data processing quality, enhancing orebody modelling, and targeting. This has had a profound impact on the industry. Moreover, the survey reveals that future transformative technologies are expected to centre on the automation of existing processes through AI and Machine Learning techniques. This is expected to help facilitate the identification of critical mineral systems and thus enable the exploration industry to make more informed decisions based on data analysis using Machine Learning and AI.

Sep 1, 2024

By M Qiao, A Sugden, W Zong, J Hines, J Roberts, T Ren

Long-term exposure to respirable dust continues to present an occupational health and safety hazard to mine workers in underground mines. Workers who are exposed to mine dust can develop occupational lung diseases including coal workers’ pneumoconiosis (CWP) or ‘black lung’, progressive massive fibrosis (PMF) and chronic obstructive pulmonary disease (COPD). To demonstrate the exposure impact of certain working conditions and improve dust management in longwall development panels, this paper details the development of a computational fluid dynamicsvirtual reality (CFD-VR) based training tool. The tool has been developed as an educational platform to facilitate the effective communication of workplace health and safety (WH&S) dust control measures for continuous miner operators and engineers. The study introduces a promising approach to model ventilation and dust flow patterns based on site-specific data, employing computational fluid dynamics (CFD) for a detailed analysis and visualisation of these mechanisms. Additionally, an algorithm has been developed for processing the large and complex CFD data sets into a form amenable for visualisation within a virtual reality (VR) environment using standalone VR headsets with limited processing power. This training tool has been deployed to mine sites with the specific purpose of educating users on the hazards of dust emissions and the best practices for control.

Apr 16, 2024

By G Pizarro, O Miranda, D Rosales

In panel/block caving mines, large amounts of information are collected at the operations. This information includes grades and extracted tonnage, fragmentation, lithology, design of stopes and main infrastructure, geotechnical information, overbreak progress, seismicity, numerical modelling and many other mine variables. To improve the reliability of the production plan it is required to integrate the mine data into one platform. In this paper, the logic of a new technological platform is presented for analysis, modelling and design in panel/block caving mines. The platform includes an acquisition system for mine data and geotechnical information, a back-analysis module for calibrating statistical models and a module of visualisation of the results. The application and benefits of the platform is illustrated for mining induced seismic risk for panel/block caving mining operation. The platform can be used in the mine design and planning processes and is useful for reducing uncertainty in the mining business of panel/block caving operations.CITATION:Miranda, O, Rosales, D, Pizarro, G and Vallejos, J, 2016. Development of an integrated platform for the analysis, modelling and design in panel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 237–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The N3500 orebody is the northern continuation of the 3500 orebody at Xstrata Copper's Enterprise Mine and occurs at a depth of 1.3 to 1.8 km. At the nearby S3500 orebody, extreme deformation was observed in access drives where there was a high number of bedding planes per metre combined with either graphite or talc infill. The observed failure mechanism was largely controlled by the geometry of the inclined bedding submitted to high horizontal stresses. Due to the anisotropic strength and deformation behaviour of the shale rock mass, traditional isotropic methods of geomechanical property estimation based upon GSI are not appropriate. A numerical modelling approach, based upon the distinct element codes UDEC (2D) and 3DEC (3D), has been developed to accurately simulate the failure mechanisms and deformation observed in the initial infrastructure surrounding the N3500 orebody.

Nov 25, 2010

By G R. Ballantyne, G Lane

Dry milling circuits that include high pressure grinding rolls (HPGR) or vertical roller mills (VRM) and air classification have replaced dry ball milling in cement production, but how do they compare to wet milling and classification circuits in mineral processing plants? Two case studies are presented that compare the energy efficiency, wear, liberation and capital cost of dry and wet milling circuits. In both case studies the VRM and HPGR consume half the energy of a wet tumbling mill for the same duty. However, the dry classification system tends to significantly erode the energy benefits. A number of improvement opportunities are presented that have the potential to improve the energy and capital efficiency of dry milling circuits. These improvement opportunities focus on the dry classification system that consumes significant energy in heating and fan power requirements and requires a large proportion of the footprint.

Aug 24, 2022

By J Sykes, W Treasure, A Saleem, A Trench, S Ulrich, R S. Davies

Below-ground technical complexity remains a traditional source of project challenge. Above-ground challenges then augment this complexity, including in the domain of commodity marketing. All challenges must be solved to produce quality, saleable, ex-mine product. The situation is further complicated in that technical complexities are not independent of each other, so complexity is best regarded as a system rather than a series of isolated factors. Additional above-ground challenges to mining projects are also increasingly sourced from societal and environmental factors, locally and globally. These challenges not only confer project complexity, but have their source in larger, global wicked problems. Finally, financing and resourcing of projects represents an ever-present challenge for all but the highest-quality mineral deposits. CITATION: Trench, A, Davies, R S, Saleem, A, Sykes, J, Treasure, W and Ulrich, S, 2018. On the sources of complexity in contemporary and future mining projects, in Proceedings Complex Orebodies Conference 2018, pp 65–66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Golsby

Both primary and secondary ventilation is important in underground mining. Secondary ventilation refers to the provision of ventilation to development ends, stopes and services facilities, which constitute secondary circuits tapped off the primary circuit or main through flow of air.An unbalanced primary and secondary combination can cause re-circulation, which is inefficient and potentially hazardous. These inefficiencies extend into operational and other considerations, such as power.Most cost justification analysis covers capital and physical consumables. These analyses are often not comprehensive or holistic. This case study is an example of ‘how to holistically justify’ a secondary ventilation circuit and optimise it to meet all stakeholder needs.This paper particularly addresses the following:how to account for all stakeholders in a secondary ventilation cost justificationthe secondary ventilation componentsthe cost justification outcomes and how to measure themsome of the sensitivitiesthe stakeholdershow to present the justification to meet the stakeholder needssecondary ventilation cost justification.CITATION:Golsby, A, 2015. Secondary ventilation as a value proposition – a case study, in Proceedings The Australian Mine Ventilation Conference, pp 49–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

The adoption of new technologies is accompanied by risks that the stakeholders will wish to understand and minimise. The process of developing a dynamic simulation and the plant it will be used in provides a discipline and attention to detail that highlights and provides an opportunity to mitigate risks that will exist in a production environment. The simulations will enable investigation of what the outcome of process failures will be and the impact maintenance. Enumerating this information will enable designs to be optimised and operating and control strategies to be tested.The success of new technology is dependent on the operators and their understanding of it and the machines that use it. In this context dynamic simulations can provide training and experience without risk to personnel, equipment or production. This experience will include situations that would not be induced in a production plant for training purposes. This paper outlines a generic template for a dynamic simulation that can be used to evaluate the introduction of an emerging technology into an operating environment. It includes process flows and surge capacity, breakdown and maintenance, operator interactions and availability, push and pull production scheduling and system control.

Sep 26, 2011

By J White

The Eyre Peninsula (EP) has been known for its iron ore for more than a century. Edward John Eyre noted the ironstone outcrop at what is now Iron Knob in the 19th century. Sir Douglas Mawson visited and reported on the geology of the lower EP in 1906, noting the widespread presence of iron stone and the likelihood of copper being associated with the iron stone. Despite this knowledge there has been only one successful iron ore mining region developed on the EP and that is Iron Knob and the Middleback Ranges which have been mined continuously since 1899. The Middleback Ranges can justly lay claim to be birth place of the Australian iron ore and steel industries.The discovery of large scale haematite resources in Western Australia meant that there was no need to seek out iron ore that needed benefi ciation. The low price of iron ore precluded further development of the EP and many other areas in Australia and overseas. This situation changed rapidly in the mid-2000s with the emergence of China as the world’s industrial power house and the soaring demand and price for many resources including iron ore. This triggered a flurry of activity across Australia and led to the rapid exploration and drives to develop the EP iron ore. A brief examination of the magnetic maps of the EP shows the wide spread presence of magnetite and associated smaller haematite deposits. A closer look reveals the magnetite deposits to vary in formation style and host rock lithology as well as being significantly altered by regional metamorphism. *This is an abstract only. No paper was provided for this abstract.*

Jul 11, 2011

By K Seddon

Segregation of tailings on deposition can occur as a result of a) sub-aqueous deposition, and b) sub-aerial deposition at lower solids concentrations (i.e. when the solids concentration is less than the segregation threshold). The effects are likely to be more pronounced in the case of subaqueous deposition.This paper presents the results of an investigation of a sub-aqueous tailings facility.Data from the investigation show extreme variations in particle size and density compared to test results for non-segregated ‘all-in” tailings. The results indicate that on segregation both the fine and coarse splits tend towards a well sorted (poorly graded) mix, and both have significantly lower consolidated density than the all in tailings. This result is reasonably well known for the case of the segregated fines (“slimes ponds”) but less appreciated for the coarse fraction. The results suggest that if the effects of segregation are not allowed for, the overall density of the deposit can be seriously over-estimated at the design stage. Also the quantity of water retained in the tailings can significantly influence water recovery and water balance results.CITATION:Seddon, K, 2018. Segregating tailings – effects on density and water retention, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 299–308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By J Kwiri, T Zvarivadza, R Mitra, F Cawood

It is crucial to record ground movement of any magnitude to enable the safe and economical design of excavations and infrastructure. The DigiMine Laboratory is equipped with technologies to record such movements. This paper analyses the effectiveness of the Digital Mine instrumentation in recording earth movements in light of the Botswanan earthquake which occurred on the 3rd of April 2017 at 17:40 UTC. Recordings from the Digital Mine are compared with other ground sensing technologies which also captured the event (USGS and GEOFON systems). USGS and GEOFON system’s recordings suggest that, there are a number of possible mechanisms that could have resulted in the earthquake as discussed in the paper. Compared to the USGS and GEOFON systems, DigiMine system could not provide an analysis that could give possible source mechanisms. However, the system’s success in recording the Botswanan earthquake, is an indication that the system works and can be further developed or improved. For a comprehensive analysis, more data from various sensors needs to be collected. For example, DigiMine connecting to the national seismic monitoring system or to the local mine’s seismic monitoring system. Such connections will enable the development of a better self-analysis system and possibly prediction of future events. More importantly, it will contribute to better understanding of regional seismicity and its potential impact on excavation design. CITATION:Kwiri, J, Zvarivadza, T, Cawood, F and Mitra, R, 2018. How efficient is DigiMine technology in recording earth movements? A look at the Botswanan earthquake, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 414–419 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By J Purandare, D Murdoch

The goal of the life-of-mine plan is to ensure that while the site is left safe, stable and non-polluting, the landscape is such that optimal use can be made of the site post-mining and closure. However, in the face of evolving shareholder expectations and the current international economic climate, numerous mines are ceasing operations and moving into a care and maintenance phase. These changes bring with them a high degree of community concern, not only about the potential legacy of closed operations, but also those mines that continue to operate.While mines across Australia are committed from the earliest planning stage to develop clearly defined post-mining land use and landform objectives, broader expectations related to these objectives may change and evolve during the life of the operation. This is especially the case where a mining operation has a project approval where the land use objectives are aligned to land capability and land use commensurate to that which occurred premining. CITATION:Murdoch, D and Purandare, J, 2016. Optimising land for beneficial use during and after mining, in Proceedings Life-of-Mine 2016 Conference, pp 166–167 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By R Pax

Feed ore variability, the major disturbance into a mineral processing plant receives considerable attention operationally, and at research and strategic levels to ensure that the throughput of the ore are maintained at all times whilst encouraging a sustainable approach to recovering the valuable minerals from ore bodies. Effort and insights from mineralogical and processing characterisation (eg. ore hardness) of sub-ore body domains allows sequencing for processing to ensure consistency and throughput for the size sensitive grinding unit processes. Optimising the blast fragmentation has benefit as does pre-concentration using ore sorting. Blending of ore domains with different characteristics is common for operations. In recent years a number of technologies have become available for on-line and more rapid assessment of ore and have been discussed in a recent paper by Cameron et.al. (2016) as an opportunity for further utilisation of mine-to-mill (and mine to product) strategies. Current concepts have focused on extensive characterisation of ores so that current control practices can be realised and made more effective with relatively slow measurements and actuation. CITATION: Pax, R, 2018. Dynamic concepts for mine to mill operation and optimisation, in Proceedings Complex Orebodies Conference 2018, pp 124–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By K Banerjee, C Dube

Veolia Water Technologies was contracted by a global coal mining company to design a retrofit acid mine drainage treatment facility using DenseSludge™ technology on a former coal refuse disposal site. The project constraint was to reuse current facilities in order to reduce additional capital work cost and avoid additional footprint requirements while improving treatment performance and reducing sludge production and chemical consumption. The initial installation of 454 m3/h served as a pilot plant to demonstrate the benefits of the process and ultimately provided design criteria for the new facility. The pilot demonstrated the benefit of the technology by reducing sludge volume by 90 per cent compared to conventional processes currently in use. The sludge that is reinjected into the mine contains less water, which reduces the volume of water that returns to the mine pool for treatment and mine water balance. Furthermore, the pilot plant reduced lime usage compared to conventional processes by operating at a lower pH set point, demonstrating steady pH control and stoichiometric lime utilisation.CITATION:Dube, C and Banerjee, K, 2015. Sludge conditioning technology to reduce sludge and the cost of acid mine drainage treatment, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 105–110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By M S. Tuohy

Poorly judged or under-appreciated change plays a role in many major accidents. In particular, operational changes related to continuous improvement, maintenance and introduction of new technology can lead to unintended safety (and other) consequences. This paper provides an overview of the role of management of change in preventing unwanted impacts on safety, community relationships and the environment. It draws on a range of incidents covering mining, minerals processing, refining and smelting where inadequately assessed or ineffectively implemented change led to significant safety, environmental or community consequences. The paper will also highlight cases of well-managed complex change and the underlying model of decision-making in place to make those decisions. All these examples are drawn from Atturra’s experience in response to accidents or working with sites to improve their management systems. The paper will report on the challenges of applying conventional risk assessment approaches to complex or technically significant change. These typically result in either onerous and lengthy change procedures that are prone to workarounds or poor implementation. Conversely, ‘light touch’ or efficiency driven change processes present the risk of intended consequences by failing to bring appropriate expertise to bear in decision-making. Such balances can be resolved by considering the designation of ‘technical authority’ with appropriate expertise to consider the change and deconflict any production, cost or schedule trade-offs. Finally, the paper will reflect on the key components of management of change systems in the context of major accidents, highlighting good practice in how they are implemented. This will consider the integration of existing corporate processes, risk management and organisational structures into management of change systems, not just the content of change forms and procedures.

Apr 16, 2024

By K W. Bian, Y M. Liu

Tongkuangyu Copper Mine is currently the only mine in China employing block caving. It comprises two large orebodies known as the No 4 orebody and the No 5 orebody. They are approximately 50° in dip angle, 80 to 240 m in width and 800–1000 m in strike length. The two orebodies are separated by a distance of 110–130 m. Production with block caving originally, ie Phase 1 project started at Tongkuangyu from the first undercut at a depth of 200–300 m below the ground surface and designated as Lift 810 m in late 1989 and has continued to the present. During the last 25 years Tongkuangyu has mined three lifts: Lifts 810 m, 690 m and 530 m. The previous two lifts utilised a slusher process with an annual designed production rate of 4 Mt. In this context the lift name represents the elevation of track haul level.The Tongkuangyu Phase 2 project serves for two lifts (ie Lift 530 m and 410 m) under the elevation of 690 m and the annual designed production rate is 6 Mt. Since the orebody is approximately 50° in dip angle, it is originally designed that production at Lift 530 m is comprised of one main extraction level and two auxiliary extraction levels in the footwall and undercutting is started from one end of the extraction footprint forward to another end, which is from north-east to south-west.Production at Lift 530 m started from March 2011 and reached to 6.39 Mt in 2013 and 6.9 Mt in 2014. Additionally, Tongkuangyu improved block caving processes and used modern mining equipment, which differ from the previous two lifts. Blastholes for undercutting and drawbell-preparation are now drilled using jumbos. The blasted ore is transferred to the underground crushing station via 10 t electric load-haul-dumps (LHDs) and then delivered to surface via a belt conveyor 3200 m long.Due to increasing ground pressure, a consequence of mining depth increase, stress abutment and inadequate support, significant damage occurred at the Tongkuangyu Copper Mine with production at Lift 530 m. This resulted in significant production delays and rehabilitation costs. A series of improvements have since been implemented including an advanced undercut sequence and increased ground support. All of these improvements have allowed Tongkuangyu to alleviate ground control issues, reduce operating costs and ensure safe production.CITATION:Liu, Y M and Bian, K W, 2016. Production at Lift 530 m of Tongkuangyu Copper Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 385–392 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J P. van Dijk, M Munro

Discrete vein modelling presents an innovative geology driven 3D modelling method for quantification of vein hosted mineral deposits, with far reaching potential for critical mineral supply and low impact resource extraction. By integrating key geological drivers with advanced discrete fracture network modelling, the DMX protocol (launched in 2019) converges to a more realistic representation of complex vein systems in three-dimensional space. The approach insights greater geologic reasoning in distributing mineral grades where vein boundaries are already defined. This presents a viable alternative to existing modelling and estimation methods and has important implications for mineral resource estimation and reporting. Further implications are discussed, where the enhanced understanding of complex orebody characteristics can potentially be used in optimising mining and mineral processing, supporting more sustainable and efficient mining practices.

Sep 1, 2024

By M Tsai

Tube bundle gas monitoring systems have been used in the mining industry for over 50 years. The initial design was based on four individual gas analysers along with a series of solenoid valves, gas sample conditioning and flow control mechanisms to ensure the correct gas flow stream volume to the analyser. Simtars staff have identified flow control issues when providing operational support to coalmines on numerous occasions. The accuracy of the oxygen analysis is dependent on control of the gas flow to the analyser. Oxygen is one of the parameters used in calculating Graham’s ratio which is used for the detection of spontaneous combustion activity in coalmines. This paper will provide data which identifies the flow control issues by comparing mine site records for the two surface sample lines in the analyser room and the gas cage. Mine sites will be deidentified within the paper. The paper will discuss some of the changes that have been made in modern tube bundle systems and compare the change to the initial design specification developed by the UK National Coal Board, investigate possible operational impacts and provide a technical fix to solve the current flow issues being experienced at some mines.

Oct 12, 2022