Search Documents

By M Nagarajan, S Esen

This paper presents three case studies from three surface coalmines. The first case study is from a coalmine where a dragline operates in 60 m wide and 1 km long strips. Typical overburden height ranges from 30 m to 50 m. The base case blast was modelled using an advanced blasting model (Distinct Motion Code – DMC) to establish the baseline using the blasting parameters in use before optimisation. DMC was used to model the alternative blasting scenarios to obtain the following key objectives:the post-blast muck pile profile was required to have an optimum height of ~28 moptimise cast percentageachieve a well-fragmented muck pile for the draglinethe muck pile profile should be appropriate for the dragline entry into the strip.Achieving these objectives would optimise the dragline performance through reducing rehandle and improving advance along the strip. DMC modelling resulted in the following outcomes:the required muck pile profile could be achievedthe cast percentage increased from 21.1 to 25.1 – a four per cent increaserehandle volumes were reduced.Establishing a good quality assurance / quality control (QA/QC) process was essential to delivering a blast that could achieve these outcomes. The blast was fired successfully and the dragline completed the strip approximately two weeks ahead of the time taken for the previous strip.The second case study is from a coalmine where D11 dozers are used to move the blasted material to the spoil. An optimum profile was required for the dozers for this low-cost mining operation. To achieve this, an electronic blasting system (uni tronicTM 600) was introduced to optimise the muck pile profiles being delivered. The new muck pile profiles showed improved cast percentage from 10.6 per cent to 17.8 per cent. The changes in the muck pile centre of mass displacement improved dozer efficiency as a result of pushing material shorter distances to its final position. Dozer productivity (bcm/h) statistically did not change but coal was being exposed at a faster rate.The third case study summarises the results from a site where dozers are used to minimise the total mining cost. Traditionally, excavators had been used on-site with conventional blast designs. After firing the first cast shot, the blasted material was found reasonably well-fragmented. Although dozing productivity hasn’t been quantified on-site, operators were providing positive feedback (easier push) due to the reasonably good muck pile profile suiting to the dozers. This site also realised significant savings with the dozing as compared to their truck/shovel operation.CITATION:Esen, S and Nagarajan, M, 2015. Muck pile shaping for draglines and dozers at surface coalmines, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 409–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By D Luppnow, H Rourke

Recent disasters such as the failure of the Mount Polley tailings embankment remind us of the risks that tailings facilities pose. It is widely recognised that dam-break assessments are a vital tool in identifying the consequences of the failure of a facility, which in turn can be used to develop emergency action plans. A typical assessment includes an estimation of breach parameters and outflow volume, followed by the preparation of an inundation map to illustrate potential flow extents and downstream impacts. This paper focuses on the estimation of outflow volumes, which is an area that the authors feel can be improved. Presently, many types of analyses assume that the volume of tailings released is only a function of the storage volume and dam height. After a review of several documented tailings failures, it has been found that the extent and depth of the supernatant pond needs to be considered as it is just as important, if not more so, as the storage volume and dam height. Tailings facilities with excess water storage have a higher risk of failure as they are more susceptible to overtopping, piping and liquefaction failures. In addition, they pose greater failure consequences as the saturated conditions will lead to more material being mobilised.This paper has reviewed available information on a number of tailings dam failures and proposes an alternative estimation of potential tailings release volumes as a function of supernatant water stored on the facility for use in dam-break analyses. In a broader sense, the paper seeks to shift the current risk paradigm from tailings dam heights to volumes of water stored and provides a basis for continuing research and discussion.CITATION:Rourke, H and Luppnow, D, 2015. The risks of excess water on tailings facilities and its application to dam-break studies, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 225–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By C D. Pocock

Maintaining catch berm capacity in open pit mines through controlled blasting prevents production delays associated with managing risks associated with wall instability. A method has been developed to quantify the drill hole deviation of presplit holes at Century Mine. Different controlled blasting techniques are used to control wall quality and decrease the risk. The performance of presplit drilling, in terms of deviation from design has been investigated. A methodology has been developed to quantify the drill hole deviation in three dimensions. This methodology was converted into a series of algorithms capable of handling an extensive range of data. The methodology was applied to a case study at Century Mine to evaluate the performance of drilling on two presplit blasts. Overall, 67 drill holes were investigated in the case study. The drill hole deviation was quantified in terms of three parameters: skewness, linearity and drill hole deviation parameter. Methods for quantifying each parameter were developed. Skewness, a measure of the amount of curvature and linearity, was defined as the measure of the consistency of the gradient of the drill hole. Drill hole deviation parameter is defined as the average measured deviation of the surveyed drill hole position from the design position. Acceptable drill hole deviation tolerances for each of the defined parameters were developed by analysing drill hole deviation parameters with respect to implications to catch berm capacity. Verification of the methodology was confirmed through the comparing of the completed drill hole deviation results using both visual inspection and cross analysis for each of the three methods. Holes with an R squared value of less than 0.97 for skewed deviation were classified as having skewed deviation, while holes with a difference in gradient of 3.5 were classified as having linear deviation. The results show that 76 per cent of the drill holes had deviation. Of this, 19 per cent were skewed, 57 per cent had linearity and 12 per cent contained both skewed and linearity deviation.

Nov 8, 2011

By C Mann, S Swapp

"The mining industry is often challenged with the task of evaluating narrow vein open pit deposits. A realistic mineable solution from optimisation needs to accurately represent mining dilution and the practical limitations of mining equipment. Open pit dilution is driven according to mining method and fleet selection as this dictates the ‘selective mining unit’ (SMU) that can be practicably mined.Common evaluation methods represent dilution by:a mathematical dilution assumption addition of a dilution skin reblocking of the model to an appropriate SMU.This paper will explore an alternative method of applying dilution by adapting an underground stope modelling tool. By considering an SMU as a stope, automatic stope shape creators such as Datamine’s Mineable Shape Optimiser (MSO) can be used to create wireframes for each mining unit over the entire deposit. Using these wireframes, the model can be subblocked and assigned as either ore (inside the wireframe) or waste (outside the wireframe) prior to optimisation.The MSO process considers SMU geometry and a depth specific value-based cut-off. The result is an optimised solution for the deposit based on practical and achievable mining constraints rather than one based on generalised modifying factors.To evaluate the economic impact of the methods above, results have been costed and scheduled and a comparison of operating cash flows made.Citation:Swapp, S and Mann, C, 2016. Optimisation Improvements for Narrow Vein Open Pit Deposits Using Mineable Shape Optimiser, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 50–59 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By H Kurth

Oyu Tolgoi copper and gold mine in the southern Mongolia holds mineral resources that make it one of the largest known copper and gold deposits in the world. The project is operating an open pit mine on the near surface of Southern Oyu deposit and developing underground block-caving mine at the Hugo Dummet North where 80 per cent of total resources exists. Oyu Tolgoi (OT) commenced open pit mining in 2011 and implemented an industry standard blasthole sampling, and ordinary kriging grade control estimation with block-out process. Since 2017, grade control improvement projects have successfully completed that have led to the implementation of current, improved grade control system. Geological model is updated by blasthole logging on Leapfrog® and used for daily grade estimations. GC estimation is proceeded solely on Vulcan® by running Lava script and integrating with a relational database. Combination of block-out procedure produces GC model which is updated in Vulcan® and as well as in the database simultaneously. Switching to the integrated database eliminated many manual processes such as importing and exporting data and enabled access to the database anytime, anywhere and from any device. Thereby, these improvements allowed to increase an efficiency, create a comprehensive reconciliation system and reduce operational risks. We are looking forward to expanding applications of integrated grade control data stored in the database. This paper outlines how the grade control system was developed at OT’s open pit mine, and how it is integrated into the short range mine planning, mine reconciliation workflow and ultimately enabled development of various automated reporting systems.

Mar 22, 2022

By J Ashford, Minniakhmetov

Geostatistical simulations are the best practice for uncertainty quantification in non-linear systems. Simulations are currently undertaken on an ad hoc basis in the mining industry due to high requirements in computing environments and advanced geostatistics. In contrast to the estimation process, multivariate simulations can be performed using different methods, tools, and computational environments, similar to data science. For large companies with multiple commodities it is important to have a standard framework to test, build, and run workflows using different methods, applications and computational environments. This work presents an auditable, modular and scalable framework to create geostatistical simulation workflows where the workflow is abstracted from the implementation. Key aspects: automation – workflows should be able to run automatically given updated data (if hands on modelling is not required); auditability – workflows should document key considerations and parameters; modularisation – workflows should permit swapping out components, for example substituting domaining in Leapfrog software with automated domaining using machine learning scripts; scalability – easy, repeatable, portable deployments on diverse infrastructure (for example, experimenting on a laptop, then moving to an on premise cluster or to the Cloud); reproducibility – parameters should be archived to permit re-running and reproduction of workflows in future years; and sensitivity analysis – any component of a workflow should be able to run with multiple scenarios of parameters and data to enable global uncertainty quantification and sensitivity analysis. The presented framework can be used to create different workflows for geostatistical simulations in multiple assets to quantify uncertainty in the value chain for resource categorisation, reserves uncertainty, value of information and robust mine planning amongst others.

Mar 22, 2022

By M Frenzel

At the last MassMin Conference in Sudbury, Caterpillar’s vision of a continuous mining concept for block caving operations was presented on the background of global raw material demand and its continuous increase. By analysing today’s structure of mining processes in block caving, the paper (Krings, Steinberg and Frenzel, 2012) highlighted the main bottlenecks in the process chain and identified conceptual solutions by help of a case study. The main focus was the paradigm shift from discontinuous batch type operation to a continuous mining process of the blocks.In 2016, the strategic vision has taken major strides forwards and remote continuous operation has become a reality. Caterpillar’s continuous operation system – the Rock Flow system – was successfully installed in Codelco’s Andina mine and start of operation is scheduled in the first half of 2016.Based on continuous product developments, this paper sets the focus on two main aspects of continuous mining. First, field experiences of the Rock Flow system will be shared, highlighting the Andina project course from system installation, to commissioning and successful system start. The second aspect concentrates on the system and mine layout as discussed in the case study scenario in MassMin 2012 (Krings, Steinberg and Frenzel, 2012).Based on Caterpillar`s continuous product development, the Rock Flow system set-up and panel design were modified for a general roadway design and drawpoint layout. The new design allows an optimised use in block preparation phase (spreading) and full production phase (reaping), operating a fleet of load-haul-dumps (LHDs) and Rock Flow systems. The combined use of the two technologies optimises the mining process in every stage of block life and significantly increases the performance of the continuous block caving operation in the production panel to pave the road for the next generation of super caves.CITATION:Frenzel, M, 2016. New continuous production system in block cave mining – the rock flow system, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 543–548 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By S Sullivan

A recent review of resource reports lodged to statutory bodies found geological models with oversmoothed or unrealistic lithological boundaries, many of which do not represent geological appearance in the field, pit or underground drive. The underlying data is often too complex or messy to be incorporated into the resource model and is thus a simplification of reality, to the detriment of the mining operation and its shareholders. Volumes can be over- or underestimated and subsequent grade predictions can be misplaced, combining to cause over- or understatement in resource reporting to stakeholders and statutory authorities. Domain models can be improved with new modelling techniques such as machine learning. However, with poor data or improper use of machine learning techniques, the conclusions can be just as misleading as with current techniques. Machine learning rarely offers a single ‘right’ outcome, rather a range of possible outcomes from the data provided. But importantly it can take advantage of the full richness of data for more informed models. Machine learning also provides confidence in its predictions so that uncertainty in the resultant models can be quantified and passed through for risk assessment during mine planning and operation. This paper will discuss the factors accentuating complexity in deposit modelling: data diversity, structural controls, chemistry, data volumes, process workflows and external non-geological constraints. A case study illustrates the risk of reducing or ignoring complexity, which can result in an overly simplified geological model.

Mar 22, 2022

By D A. Williams, J C. J Boshoff

The properties of tailings that emanate from laterite nickel processing plants are significantly different to most other mine tailings. They typically comprise a mixture of fine materials that are made up of altered clays, chemical residues and salts. Neutralisation processes that are undertaken prior to tailings discharge result in a high proportion of gypsum in the tailings. The salinity of the pore fluid is commonly higher than 140 g/L of salts, dominated by magnesium sulfate. Hydraulically-placed tailings that undergo solar evaporation typically reach dry densities of less than 1 t/m3 of insoluble solids. In situ water contents after many months of drying may be as high as 80 per cent, and peak undrained shear strengths are unlikely to be greater than 20 kPa.This type of material is not conducive to upstream raising, from both a practicality and overall slope stability perspective. Even at rates of rise of less than 1 m/a, it is difficult to effect upstream raising on unaltered laterite nickel tailings. However, the authors have successfully designed and implemented upstream-raised laterite nickel tailings storage facilities. The upstream raises have been formed from both imported natural materials and air-dried and compacted tailings borrowed from the tailings beaches.Drying and associated strength gain has been achieved through various means of mechanical intervention, repeatedly exposing a zone of tailings to the atmosphere for evaporation. Field trials have been undertaken to optimise the approach, and the findings from the trials have been implemented in practice to allow stable upstream raises to be constructed. The cost savings and reduced environmental impact compared to high-volume downstream raises have been significant.CITATION:Williams, D A and Boshoff, J C J, 2015. Upstream raising of laterite nickel tailings storage facilities, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By L van Latum, A Koh, I Thomas

Haul truck drivers are at a high risk of developing fatigue due to the monotonous nature of the work and demanding shift rosters. In the mining industry, fatigue is identified as a major contributing factor in several fatal accidents a year. A number of fatigue detection devices are now available, that can contribute to improved fatigue risk management in the mining industry. This paper describes the technology and algorithms behind one particular product which is both predictive and un-obtrusive to the operator. The Advisory System for Tired Drivers (ASTiD), was developed by Fatigue Management International (FMI) in collaboration with the Loughborough Sleep Research Centre (LSRC), both in the United Kingdom. While this system includes a model of the human circadian rhythm as a bias for predicting expected fatigue risk by time of day, it also uses yaw data generated by a solid-state gyroscope in the horizontal plane. Algorithms analyse this data to determine the level of monotony of actual driving conditions and to detect changes in steering control caused by driver fatigue. During normal levels of attention, a haul truck driver applies continuous, small adjustments to the steering wheel. As the level of fatigue increases, steering adjustments become less frequent and more erratic. Differentiating between these modes of control in the highly variable mining environment is accomplished by chromatic processing of the gyroscope data. This paper will go into some detail explaining the principles behind chromatic processing and the specific application of these in detecting fatigue in haul truck operators.Technology in itself is not the solution to addressing operator fatigue, but it plays an important role in ongoing monitoring and maintaining awareness with mining personnel. Furthermore, the specific principles behind ASTiD technology support a risk-based approach to fatigue management, allowing optimisation of the mining operation for productivity as well as safety.

Sep 26, 2011

By I Grewal, B Klein

The Knelson Continuous Variable Discharge (CVD) is a continuous centrifugal gravity concentrator for high-mass yield recovery applications. It has four operating variables that enable control of mass yield, product grade and recovery namely: fluidisation water, bowl speed, pinch valve open time and pinch valve closed time. Plant testing of a pilot scale Knelson CVD6 was conducted to evaluate the effects of operating variables on mineral separation. The analysis of operating variable effects has provided a framework for the development of operating guidelines for the CVD.

Jan 1, 2001

By J Kwak

Driving sustainability concepts and practices into the heart of the design process is the key to achieving a successful, sustainable plant design. Engineering design practices, tools, systems and methodologies should be prepared around true eco-efficiency parameters, adopt wholesystems-thinking and consider life-cycle impacts for the design task. Experience dictates that the application of sustainable plant design practices is most likely to succeed if: The principles are well documented and explained. All stakeholders agree on what sustainability means. Sustainable plant design is treated as a core process. The principals of sustainable plant design are equally applicable in brownfield and Greenfield environments. Although brownfield situations provide the designer with less latitude for change, these types of projects do allow easier measurement and demonstration of relative impacts. This paper further develops the above points by drawing on case studies from HatchÆs repertoire.

Jan 1, 2004

By M Ozkayhan, N Arslan

"The Efemçukuru underground mine in western Turkey is an intermediate sulfidation, epithermal gold deposit. The bulk of the mineral resources and all of the mineral reserves lie within the Kestanebeleni (KB) vein system. This system comprises four spatially-distinct mineralised zones: the south ore shoot (SOS), the middle ore shoot (MOS), the north ore shoot (NOS) and the KB north-west ore shoot. Production currently occurs only in the SOS, MOS and NOS zones. The gold mineralisation is very fine grained and occurs as free grains in quartz and carbonate, and as inclusions in sulfide minerals. Gold is recovered as part of a sulfide concentrate by flotation methods. Though hosted in the KB vein, the gold mineralisation is not evenly distributed within the veins. Definition of its occurrence is totally dependent on diamond drilling.Diamond drilling at Efemçukuru is done with its own equipment and staff, all managed by the mine geology group. The process over the mine’s six year production history incorporates continual improvement with an innovative approach by focusing on the following: drill team organisation career development and training product research and effective equipment management cost reduction planning and scheduling of development for drill stations.Over 40 000 metres of mostly BQ size core are drilled annually by three drill rigs at a cost approaching US$35/m.The planning and execution of the drilling pattern depends on the configuration of the ore shoot and the planned mining method. Ore extraction is mainly by drift and fill mining augmented by about 15 per cent longhole stoping. The drilling of a specific area is scheduled to be finished 3 to 8 months prior to mining. This scheduling is sufficient for short-term grade model updates and any needed changes to the planned development or stope sequencing prior to planned production from the stope area.CITATION:Arslan, N and Ozkayhan, M, 2017. Diamond drilling at Efemçukuru gold mine, Turkey – a case study on the benefits of timely and cost-effective drilling to short-term planning, in Proceedings Tenth International Mining Geology Conference 2017, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 20, 2017

By L A. Balzan, F Nieuwenhuys

GEOSCAN on belt analysers have been widely utilised in iron ore for nearly two decades. Since the first installations in 2003, the availability of accurate and reliable grade data has become standardised across iron ore mines in the Northern Cape in South Africa, where various streams are monitored continuously to ensure the optimal functioning of plants. Assmang Khumani has been at the forefront of technology adoption, and has implemented 19 GEOSCANs at various locations throughout the plant, monitoring run-of-mine, stockyard feed, beneficiation plant feeds, and products. Over the years, collaborative advances in the technology have allowed for numerous benefits and gains to be made. In recent times, there has been a concerted effort on the development of analysis for phosphorus in the material flows, and based on Scantech’s experience in the phosphate industry, this element has now been calibrated to achieve statistically acceptable and repeatable accuracies for real time analysis of this element on many of Khumani’s GEOSCAN analysers. This paper provides an overview of GEOSCAN use at Khumani, while focusing on the development of phosphorus analysis. A case study of analysis results is presented for a range of analysers that have been calibrated for this element, as well as a discussion on the benefits obtained as a result of this analysis.

Nov 8, 2021

By A McCallum, J Abols, G Patrick, G Johansen

The authors challenge the traditional thinking that whole ore cyanidation followed by Carbon in Pulp (CIP) or Carbon in Leach (CIL) should be applied as a standard process in the majority of gold processing flow sheets. The concept of whole ore leaching by using cyanide can result in unnecessary environmental and capital risk. Alternative, currently available technologies can be used to provide the desired level of gold recovery at a much lower installed cost and less impact on the environment. Gravity concentration, alone or in conjunction with flotation, can produce a gold bearing concentrate that can then be fed directly to a batch or continuous intensive cyanidation unit. The In-line Leach Reactor (ILR) is an intensive cyanidation unit developed by Gekko Systems of Australia. Advantages of this technology include significantly reduced capital outlays for greenfield plants or plant upgrades and increased investor returns. Reduction of onsite cyanide and carbon inventories improves plant safety, materials handling and site security. By using direct electrowinning to treat the gold bearing solutions produced by the ILR, the need for a conventional carbon stripping circuit is removed. Potential also exists to increase grind size û saving energy, further reducing capital and operating costs and decreasing the environmental impact of a mill. Detoxification of cyanide before the release of solution to the tailings dam can minimise tailings disposal and containment requirements. When used in the right application the proposed process will have little or no impact on gold recovery and may actually increase recovery for complex ores. Areas applicable to this type of treatment include: plants in environmentally sensitive regions, lower tonnage higher grade deposits, coarse gold deposits, and preg robbing ores û some of which may not currently be economically feasible using standard processes and flow sheets. We have provided two examples of such projects, where an alternative to whole ore leach and CIP or CIL has the potential to deliver these benefits.

Jan 1, 2004

By G Haywood

This paper presents the evolution of the planning, scheduling and mining practices at the Yilgarn Star underground. The paper will concentrate on the principals of æjust in timeÆ and the impact of such practices on mine planning and scheduling and subsequent development and production. The principals of æjust in timeÆ were developed to minimise the impact of creep and time dependent failure of the ground in the ore and hangingwall zones. These zones are characterised by altered schistose material with inherent weak rock strengths compounded, at depth, by the maximum principal stress of the virgin stress field approaching the UCS of the rock mass. Yilgarn Star underground has and continues to develop the æjust in timeÆ methodology to ensure the continued viability of the mine. The mine continues to use longhole open stoping mining methods to ensure high levels of productivity with minimal dilution and at an acceptable cost of production.

Jan 1, 2002

By J Loeb, D Thornton

Blast movement measurement is a key component of grade control, enabling mines to carry all of the precision involved in locating ore blocks, through a chaotic blast, to production. A monitoring system was developed about ten years ago so that mine operation personnel can measure three dimensional movement in every production blast. Research has shown that blast movement is always highly variable with a significant non-deterministic component. The consequence is that modelling will be inaccurate and therefore optimal ore recovery can only be achieved by direct measurement of blast movement.Three dimensional movement vectors are measured at discrete locations in the blast. If blast movement is only measured at one location in a blast pattern, data is severely limited and has all of the inherent inaccuracies of modelling a variable population. It is intuitive that the accuracy of defining the post-blast ore block mark-ups are proportional to the number of movement measurement locations, however increasing the number of monitoring locations causes increases to the direct operating costs of the mine.A cost-benefit analysis is used to explore the optimal number of monitoring locations. Using the method described in this paper, an automated selection of the number and location of blast movement monitors are analysed against the value of recovered ore compared to the control, for each trial.CITATION:Loeb, J and Thornton, D, 2014. A cost benefit analysis to explore the optimal number of blast movement monitoring locations, in Proceedings Ninth International Mining Geology Conference 2014 , pp 441–450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

Is your company paying taxation on profits which are partly illusory?ò Are unions making wage demands based on erroneous notions of the real level of value added to your companyÆs production?ò Do you receive historic data on profit contributions by different products, or for different market areas, which you feel may be misstated?ò Do you find that cash is not always readily available to pay dividends out of reported earnings because, it is required to finance additional working capital without a real increase in the level of activity?ò Are your planning and budgeting routines hampered by the need to rely on historic financial data which bear little resemblance to what the future may hold for your company?ò Are you able to maintain your business at its optimum operating capability or do you feel each year that it becomes more and more difficult to achieve the same volumes of prdduction at the same level of return on assets employed without having to raise more capital?If your answer to any of these questions is "yes", then it is very likely that Current Cost Accounting (CCA) has something to offer you!characteristics of the mining industry and for single venture mining operations.

Jan 1, 1984

By P Wilson

The Mt. Wright Underground Mine is located near the town of Ravenswood in North Queensland and is operated by Carpentaria Gold – a wholly owned subsidiary of Resolute Mining Limited. The establishment of the world’s first Sub Level Shrinkage (SLS) mine from a tradition Sub Level Open Stoping operation has proven to be a geotechnical challenge which has required tailored solutions to overcome unique issues. This paper will be broken into two distinct sections that will outline: a brief overview of the mining method and how the SLS method was chosen; and how the SLS is managed and key geotechnical learnings. The story of the world’s first SLS originated from the need of a bulk mining method to ensure the viability of Mt. Wright into the future. Traditional bulk mining methods such as; Block or Sublevel Caving were originally ruled out due to the low natural ‘cavability’ of the orebody and the proximity of the orebody to existing major infrastructure (Decline, Ventilation Rises and Egresses). The first section of the paper will outline the key geotechnical information that helped decide the SLS method in addition to how continuous backfill influenced the design. The second section is intended to address issues that the geotechnical engineers encountered since the inception of the SLS. The feature topic of this section is mining induced stress. Like most bulk mining methods, Mt. Wright had success when the production front was running parallel to the stress (production front being ‘shadowed’ from the stress). This was until a design change, forced by a splitting ore body resulted in this shadowing effect becoming harder to achieve. As a result, rehabilitation and production hole re-drilling become a regular occurrence, which teamed with a strict set of access controls made the production cycle longer and harder to complete. CITATION:Wilson, P, 2018. Mt Wright – geotechnical learnings from a sub level shrink, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 119–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Bourcier, T Rafferty

Following an underground coal mine explosion, it is important that ventilation is quickly restored to ventilate the mine and affect a mine rescue. To achieve this, surface ventilation fans must be suitably protected from explosion damage, but still able to be quickly restored.A review of all Australian coal mine regulations was carried out, revealing that Australia has no prescriptive regulations that specify the design of explosion relief panels and the protection of ventilation fans in the event of an underground explosion.To better define the level of protection required, this paper reviews and extracts details from relevant major international regulations and standards on the subject.A suitable design methodology for the protection of ventilation fans is presented that could be applied in Australia, using a combination of explosion relief panels, appropriate isolation of the fan, and ventilation shaft/mine design.CITATION:Rafferty, T and Bourcier, R, 2013. The protection of surface ventilation fan installations from underground explosions, in Proceedings The Australian Mine Ventilation Conference , pp 169-173 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013