Search Documents

By P Marlow

Raiseboring is an attractive method of constructing shafts, being safe, fast and comparatively cheap. But this means back-reaming through weathered ground. However in the gravels and weathered near-surface rocks typical of the Western Australian goldfields, back reaming large diameter shafts through to the surface is risky and conventional sinking from surface has normally been required.An alternative construction approach has recently been used to stabilise the weak surficial materials and allow raiseboring through to the surface. The method is based on first installing rings of non-contiguous reinforced bored piles around the shaft perimeter, for temporary support, then back reaming shafts at full diameter through to the surface. Immediately after the reaming head is removed, the weak exposed materials are supported using remotely sprayed fibrecrete.The method has been successfully applied to four shafts since July 2007; 3 m and 4 m diameter shafts at Trident Mine, a 3 m diameter shaft at Wattle Dam and a 4.5 m diameter shaft at Athena Mine.Bored pile layout designs have varied from eight to 24 piles, of diameters 120 to 270 mm, in one or two rings. In one case, the top 10 m of the proposed shaft was pregrouted. Subsequent surveys have confirmed that fallout occurred in some shafts, out to the ring of piles, implying that the piles inhibited collapse.The practical implementation of the method was not always easy and many valuable lessons have been learnt. This paper documents key aspects of the method and the critical elements for its application.

Mar 21, 2011

By V Liebezeit

Data management is a significant, but perhaps unrecognised, consideration for any organisation embarking on a geometallurgy program. While resource geologists are accustomed to dealing with thousands or millions of samples and their associated assays, metallurgists and mineralogists have traditionally carried out only a few expensive and complicated tests and consequently tend to manage the resultant data in spreadsheets. The emerging discipline of geometallurgy arrives with significant challenges as a result of the sheer volume of data generated. As an example, the Olympic Dam geometallurgy program has generated more than:60 000 physical subsamples analysed for up to 30 analytes; 25 000 spreadsheet-based laboratory test results; 30 000 sized fractions analysed via QXRD, MLA and/or QEMSCAN;multiple external providers of data, and more than seven terabytes of data. Considerations for any geometallurgy data management system include storage space, data integrity, accessibility, traceability (sample provenance), maintenance and ease of use, integration with data providers and the ability to modify the system to adapt to changing requirements. Further, aspects of a geometallurgy program, such as conducting a range of tests on one sample, producing subsamples such as concentrates and tailings, compositing and routine QA/QC may not be well handled by existing software and providers geared to standard geochemistry, mineralogy or metallurgical test programs. The development of a geometallurgy database using existing software (AcQuire), and the associated file management system will be described for a large geometallurgy program at Olympic Dam. As with many aspects of geometallurgy there is no approach that meets the needs of every site or program. Recognition of data management as an issue, a structured approach in the program planning phase and commitment to executing the strategy will increase the chances of successfully mining the geometallurgical data.

Sep 5, 2011

By F Grobler

Many projects fail because project performance in unfavourable economic conditions was not anticipated at the investment decision stage. This type of failure may have been avoided through the selection of a strategy that enables the project to perform well under a range of possible future economic conditions (a ærobustÆ strategy); rather than an æoptimalÆ strategy for expected future conditions that will never eventuate. This paper describes a method of rapidly generating mine plans for a number of project strategies, and then evaluating it against a representative range of equally likely economic conditions. The key performance indicators derived for each strategy are the mean value and the distribution of values (variance). A prudent investor will identify prospective strategies not only on the merit of highest mean values (as a proxy for economic reward), but also on the probability of not meeting specified investment hurdles (a proxy for risk). A robust strategy will achieve its financial objective even under adverse economic variations. This paper focuses on the effect of commodity price uncertainty; particularly around the choice of mining and processing capacity levels. Results from enumerating 2000 prices scenarios against 63 strategy combinations show how processing and mining capacity can be manipulated to manage the risk-reward trade-off.

Sep 26, 2011

It is well known that the ability to influence project value reduces significantly as planning progresses and decisions regarding project parameters are made. However, at the prefeasibility stage in particular, where one of the main aims should be to evaluate a wide range of options in order to select the best for more detailed further study, there is often a reluctance to spend the time and money needed to do this rigorously. This paper demonstrates, by a number of case study examples, how significant increases in value may be obtained by fully evaluating the combinations of alternatives for various project design parameters, including (though not limited to) mining methods, haulage methods, mining rates, processing methods and rates, sequencing of mining, and cut-off grades, with changes and upgrades over time where applicable. The additional value unlocked is typically orders of magnitude greater than the additional cost of the more comprehensive study. The dangers of misuse of simplistic sensitivity analyses and failure to identify how strategies might change in response to changes in external factors are also illustrated, and the importance of selecting the best ægrade descriptorÆ is discussed.

Jan 1, 2007

By A Hacket, M Haest, I Vitins

Infrared spectroscopy has the ability to accurately measure mineralogy of drill cores, allowing for better spatial characterisation of iron ore deposits and potentially improving the prediction of key mining and processing parameters at the deposit scale. BHP Billiton Iron Ore is using infrared spectroscopic drill core logging to provide fast and accurate mineralogy for diamond cores and reverse circulation (RC) samples.Mineralogy can be predicted from infrared spectroscopic drill core data with errors on estimates ranging from six to 12 weight per cent. The error on the clay estimates is significantly lower than for hematite and goethite content estimates. This manuscript presents the results from a study on a bedded iron ore deposit, hosted in the Brockman iron formation, for which infrared spectroscopic data were collected on all of the diamond and RC drilling. Results show that these mineralogy estimates improve drill core logs, the geology model and the metallurgical block model.CITATION:Haest, M, Vitins, I and Hacket, A, 2013. Infrared spectroscopic drill core logging - making inroads to deposit scale 3D mineralogy, in Proceedings Iron Ore 2013 , pp 251-258 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By N Setoudeh, A Nosrati, N J. Welham

The current surge of interest in lithium (Li) is due to the anticipated demand for electric vehicles and small scale power storage. Brine deposits contain most of the global Li resource, however hard rock deposits can be more readily and rapidly developed and comprise the majority of proposed projects. These projects plan to use the conventional processing routes of dense medium separation and / or flotation to produce a spodumene concentrate for sale. The standard route for subsequent processing of spodumene concentrate is thermal decrepitation, acid leaching, solution purification and precipitation of lithium carbonate. This is typically followed by further purification. A number of projects have ores which contain other lithium minerals, principally micas, lepidolite and zinnwaldite, necessitating an alternative treatment route. Several different routes for spodumene processing are under development to reduce costs to compete with brine projects. This paper will give an overview of the strengths and weaknesses of the current and alternative processes.CITATION:Welham, N J, Nosrati, A and Setoudeh, N, 2017. Lithium ore processing – an overview of the current and new processes, in Proceedings MetPlant 2017, pp 185–194 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

By H Esterhuizen, W Hartman

Rockfalls or significant deterioration of mine openings can have significant safety and financial impacts for mining operations. The failure of drives in underground mines sometimes highlight deficiencies in the mine risk management systems in detecting geotechnical hazards and to prevent events that can have significant impact. Consequences from these failures includes fatalities, injuries, loss of revenue, additional cost, and potentially a loss in Ore Reserves. Where the impacts are severe, it also affects families and communities linked to the operation. The assessment of underground excavations requires consideration of the full range and spectrum of geotechnical hazards, design aspects, ground support, layouts and sequences. Where the assessment of these are insufficient or incorrect, it can result in drive failures. Care must be taken that meeting production targets and personnel pressures do not result in a situation where production take preference over a proper risk-based assessment of the drives to be mined. The risk management approach is now widely accepted in the mining industry for the control and management of risks in underground mines. Codes of Practices (COP’s), Ground Control Management Plans (GCMP), Principal Hazard Management Plans (PHMP’s) and technical guidance documents has become the norm for describing the mines main hazards, risk levels and intimating controls for safe passage of vehicles and mine personnel. However, where there is a disconnect between these documents and what is actually being done at the mine site, the COP’s and/or Management Plans become ineffective (or vice versa). This disconnect may occur due to the actual content of these documents, a lack of resources, or a lack of understanding about the implementation. There is therefore a need for sites to have a documented and implemented risk-based approach for assessing underground mine development. This approach or system needs to identify all hazards and other factors affecting mine development stability early on in the design process, and outline the risk classification and controls required. This paper presents an amalgamation and modification of previous processes for a Geotechnical Risk Management System for Underground Mine Development. CITATION:Hartman, W and Esterhuizen, H, 2018. A geotechnical risk assessment tool for underground mine drives, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 235–253 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By R Atmuri, W Liang, R Prasad, Y Liu, E Wingate

Yellow phosphorus (YP) has been commercially produced since the 1920s. First in the USA by the Tennessee Valley Authority (TVA), next in Russian (Kazakhstan) in the 1950s, and finally in China in the late 1970s and early 1980s. There are operations in Vietnam and Sarawak on a smaller scale. YP has become very in vogue due to its use in the production of lithium iron phosphate battery cathode precursor materials by the Chinese and other western battery manufacturers. The YP is also used to produce purified phosphoric acid and higher grades of acid using a thermal oxidation process after smelting. This paper will look at the basics of the smelting including slag chemistry, alloy chemistry and offgas chemistry. The paper will look at the design of the furnaces used in the YP production process as well as the downstream recovery of phosphorus from the smelter off-gas stream to YP. The next part of the discussion will focus on the operations of a YP smelter with regards to control of the furnace to optimise phosphorus recovery to YP. Will discuss tapping cycles for alloy and slag with a view to optimal phosphorus recovery. The discussion will close out with a review of operational challenges in the smelter and a brief description of the downstream conversion of YP to high purity phosphoric acid.

Aug 21, 2024

By S L. Martin, M Wimberger

The binary indicator coding of assay and lithological data according to a single criterion or multiple criteria is a powerful technique for representing mineralised shapes through the modelling of probabilities. This can be as simple as using a single indicator to model the probability of occurrence of a condition, usually a grade threshold or a lithology, but it can also be used with a number of categories. Case studies are presented to show the power of this approach, where the geological controls on mineralisation or on the distribution of a rocktype or alteration, often coupled with mineralisation, are unclear. The categorical approach is often used as a de facto grade filter in disseminated or stockwork mineralisation. The ultimate expression of the indicator formalism is in multiple indicator kriging (MIK), where a conditional distribution of probabilities is generated for each estimation panel. This has applications in recoverable resource estimation, as the input for continuous or categorical simulation, where the distribution of sample grades is multimodal, or when there are superimposed mineralisation events with different orientations. However, in some cases, MIK is being used as an excuse for ignoring a quality geological interpretation. Examples from the public domain show the abuse of the categorical and MIK approaches to modelling probabilities, together with a plea for greater consideration of the geology.

Mar 22, 2022

By J Pan

In this paper, the technology of producing fluxed pellets by using hydrated lime as binder instead of bentonite was carried out. The properties of the two types green balls (0.8 per cent bentonite and 2.0 per cent hydrated lime) were as follows: drop numbers of 4.8 - 5.0 times/0.5 m, compressive strength of 19.7 - 24.2 N/pellet and thermal shock temperature of 280° - 385°, respectively, under the same conditions of 1.5 per cent coke, 1.45 basicity and balling at 8.5 per cent moisture for 13 min in disc pelletiser. Comparing with bentonite as binder, the compressive strength of fired pellets with hydrated lime is elevated by 13.8 per cent and climbs up to 3113 N/pellet under the following conditions: preheating at 1050°C for ten minutes and fi ring at 1300°C for 15 min. In the mean time, the hydrated lime also improves the metallurgical performance of fired pellets. The reduction index was enhanced from 68.6 - 70.6 per cent, RDI+3.15+ increased from 90.1 to 98.8 per cent and reduction swelling index dropped from 22.4 - 7.4 per cent, respectively. The mineral compositions and microstructure of fi red pellets shows that the fired pellets containing 2.0 per cent possess more calcium ferrite and magnesium ferrite and compact microstructure, leading to the higher compressive strength.

Jul 11, 2011

By C Lower

An unprecedented, quantitative, deposit-scale understanding of major clay mineral distribution throughout the Yeelirrie uranium deposit has been achieved by adapting the existing HyLogger™/HyChips™ analytical technique to measure resource assay pulps. Spectral analysis via HyLogger™ and HyChips™ systems has previously been used as a small-scale geometallurgical research tool, but never before has it been quantitatively applied to an entire resource sample population for the purpose of developing stand alone block models for major clay minerals. Economic uranium mineralisation within the thin but extensive Yeelirrie?palaeochannel?primarily exists within the transition zone between a groundwater-derived calcrete and the underlying clay-quartz regolith. Early geometallurgical investigations identified that certain clay minerals could be deleterious to the efficiency of the uranium recovery process. Accurate calculation of clay mineralogy from resource assays proved too difficult due to chemical similarities between co-existing kaolinite, smectite and magnesium carbonate minerals. A relatively low-cost, efficient and accurate method of quantitative clay mineral analysis was required to measure over 70 000 resource assay pulps. After initial testing and comparison with QXRD, the HyChips™ 3-1 spectral logging system was implemented as a primary method of clay mineral analysis for the Yeelirrie uranium deposit. The resultant spatial data set allowed the interpretation and geostatistical analysis of geometallurgical domains across the deposit. Clay block models were generated and used in geometallurgical resource calculations to benefit the mine planning process.

Sep 5, 2011

By M Saghaeian, A H. Baladastian, A Dehghani Ahmadabadi, V Sheikhzadeh, R Hejazi

This research was done to reduce silica from mixed hematite concentrate of Barfkar Iron Ore Sample and increase Fe grade using reverse flotation method (Depressing Hematite and floating Silica). The used sample in the reverse flotation tests was a mixture containing two types of hematite concentrates (Spiral cleaner concentrate and Slon-VPHGMS cleaner concentrate) with the percentage of 16 per cent and 84 per cent, respectively. Fe grade of two samples was 59.31 per cent and 57.52 per cent and SiO2 grade was 5.83 per cent and 6.71 per cent, respectively. After mixing, the Fe and SiO2 grade of the mixed sample was measured at 58.10 per cent and 6.20 per cent. For flotation tests, effect of variable operational parameters including feed size distribution (d80 = 130 microns and d80 = 53 microns), pulp solidity (25 per cent and 30 per cent w/w), pH (9.70, 10.20 and 11), Sodium silicate as a dispersant (500, 1000 and 2000 g/ton), Starch as a depressant (500, 1000, 2000 and 3000 g/ton) and EDA as a collector (180, 300, 400 and 500 g/ton) were investigated. For evaluating the influence of Sodium silicate and Starch dosage, initial flotation tests were performed on the main sample (d80 = 130 microns). These two parameters had no significant effects on the yield, Fe, and SiO2 grade of flotation concentrate based on test results. In the next step, screen analysis was carried out on the main sample for mineralogical studies. Accordingly, the suitable size distribution for releasing Fe and SiO2 particles was smaller than 53 microns. Therefore, the sample was crushed until d80 = 53 microns. Then, supplementary tests were performed on the crushed sample for studying the pH range, pulp solidity, and EDA collector dosage. After doing silica removal flotation tests based on the designed pattern and comparison of the results, the conditions consisting of size distribution d80 = 53 microns, pulp solidity 25 per cent, pH 10.20, Sodium silicate 1000 g/ton, Starch 1000 g/ton, and EDA 500 g/ton was selected as optimum values. In the last test, Fe and SiO2 grade was measured at 60.00 per cent and 3.93 per cent, respectively, and Fe recovery was obtained at 74.93 per cent.

Aug 24, 2022

By H M. Parker, G Verly, T Postolski

Assessing the uncertainty and risk in mineral resource estimation is required for best practice and is implied by the public reporting codes in the categorisation of mineral resources and reserves. One industry best practice is quantifying the risk on future production for a given period, which can be done using two geostatistical approaches: conditional simulation and drill hole spacing studies based on estimation variances. Conditional simulation can provide a more complete and flexible answer to the problem, but it takes a fair amount of time to complete. Drill hole spacing studies are simpler, faster and can provide reasonable assessments of mineral resource uncertainty.This paper is a presentation of the principles, theory and practice of drill hole spacing studies. Various types of risk assessment are considered. Difficulties encountered in practice are discussed, and solutions are proposed. The important parameters impacting the results are reviewed. Examples of results and sensitivities are shown.CITATION:Verly, G, Postolski, T and Parker, H M, 2014. Assessing uncertainty with drill hole spacing studies – applications to mineral resources, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 109–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

Discovered in 1954 and mined since 1966, the X41 copper orebodies have produced over 143 Mt @ 3.3 per cent copper. By June 2002 the production from these orebodies had depleted the Mineral Resource to 36.6 Mt @ 2.8 per cent Cu (including 31.5 Mt @ 2.5 per cent Cu combined 2002 Ore Reserve). Mine production will ramp down to cessation beyond ten years. The 2002 Copper Business Study was commissioned to review the status of the Mount Isa copper business and to optimise the long-term strategy of the operations. The study resulted in a vastly improved geological and geostatistical model, and financial studies led to the optimisation of mine cut-off grades. Utilising these new models, a near-mine target generation workshop was conducted by the copper stream geology team. The workshop focussed on exploration for new ore sources and the extension of existing orebodies to supplement the Mineral Resource inventory for future conversion to Ore Reserves. Several prospective targets were identified and the Conceptual Northern 1100 Drilling program was subsequently designed. This paper shall discuss the practicalities of near-mine target generation in Mount Isa, the issues faced when locating and preparing drill sites in a mature mine environment, and the preliminary results of the drilling program so far.

Jan 1, 2003

Late Cretaceous and early Tertiary coals in the Greymouth, Ohai and Kaitangata coalfields represent a major national energy resource comprising-up to 2500 x 106 tonnes of coal in ground. The three coalfields are closely related in terms of age and sedimentary and structural character. The most striking feature common to all is the complexity of the geology which has severely restricted exploration and mining of these coal resources. This complexity is manifest in the irregular lensoid nature of coal seams and by the incidence of unpredictable medium and small scale faulting and folding. There are many geological similarities between these coalfields which are considered to arise from a common origin which can be related to the plate tectonic evolution of the southwest Pacific region. In order to efficiently assess and exploit these coal resources it will be necessary to know their geology in great detail. This can he achieved by increasing the understanding of the sedimentary and structural evolution of the coal bearing basins. This knowledge may be gained by the application of traditional (ie drilling, field mapping) and innovative techniques (ie high resolution seismic, in seam seismic) with on going research-oriented studies (ie basin analysis, coal petrography).

Jan 1, 1987

By M A. González, J A. Romero, D L. Fuentes, C J. Poblete, O Abdrashitova

"Robustness can be defined as the ability of a system to resist change without adapting its initial stable configuration. Robust design methodology, which is widely accepted in the manufacturing industry, allows the establishment of robustness and reliability metrics in scenario analysis.In the mining industry, a mine can be considered as a system with design parameters such as processing plant and mining capacities. Traditionally, a limited number of scenario iterations are performed in an attempt to determine optimal capacity values. An important strategic decision such as process plant capacity in particular is made during the very early stages of a mining study, often based on a low level of information. Lack of time and tools to run and analyse a larger number of possible scenarios for different design parameter combinations are usually the main reasons for not performing a full analysis. In addition, the uncertainty of other mining study input parameters creates more risk in decision-making.With advances in technology, it is now possible to automate the process of generating several thousands of scenarios in an affordable and timely manner. This allows performing the results analysis and assessing robustness and reliability criteria within a reasonable time frame. It is possible to generate a surface of results based on the net present value (NPV) for each scenario. This surface will reflect the efficiency level of the capture of the economic rent for each production scale. In addition, each scenario can be tested under diverse conditions of volatility of other external variables such as prices, costs or recoveries for example.This paper aims to establish a methodology that applies robustness criteria to determine the best scenario on several surfaces of value, which is then assessed with real data from a mining project. Obtained results demonstrate the advantages of using the proposed methodology in dealing with the above-mentioned multidimensional problems. It allows better decision-making on key design parameters and better control of the risks of a strategic mine plan.Citation:Poblete, C J, González, M A, Romero, J A, Fuentes, D L and Abdrashitova, O, 2016. Use of Robust Design Methodology for Production Scale Definition in Open Pit Mining, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 284–291 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By Kerr I. D, Kennedy M

Flash X-radiographs were obtained of commercial electric No 6 and No 8* strength aluminium tube detonators in small-diameter cartridges of emulsion explosive at various times after fusehead operation. The trigger system for the radiography was based on the detection of light following fusehead firing via optical fibres inserted into the fusehead cavity during detonator assembly. These experiments were simulated using a finite element hydrocode with realistic treatment of the non-ideal reaction kinetics. Excellent agreement was demonstrated for the shape and position of the shock waves. In both cases, initiation of the emulsion was predominantly forward from the detonator. For the No 8* strength detonator, this initiation resulted from the shockwave delivered through the sides of the detonator, while for the No 6 strength detonator, initiation was the result of a complex interaction between shockwaves originating both from the sides and from the endcap. In the reverse direction (towards the crimped end of the detonators), initiation was only weakly dependent on detonator strength, being controlled mainly by the competing processes of rarefaction from the cartridge boundaries and comer turning of the detonation wave from the forward initiation. The consequences for field performance of small-diameter emulsions will be discussed.

Jan 1, 1990

By T Honeyands

At present we are witnessing large investments in the iron ore industry, fuelled by demand from Asia. At the same time, there is a changing landscape in pricing of iron ores, with the recent demise of the benchmark system and the evolution of market based index pricing systems. From a customer perspective, it is the behaviour of iron ores in downstream processing that gives them their value; their impact on the sintering or pelletising process and subsequently blast furnace ironmaking. It is therefore important to consider this value when developing projects, making mine planning/cut-off grade decisions, and in setting quality price differentials.This paper describes the use of the Marx value in use (VIU) model to quantify the downstream value of iron ores. The Marx model consists of heat and mass balance modules for sintering, pelletising and a rigorous two-stage heat and mass balance model of blast furnace ironmaking. Mass balance and cost models are applied for steelmaking, casting and rolling. The use of a heat and mass balance allows accurate comparison of the impact of raw material properties on blast furnace operation. The impact of minor elements, such as alumina, silica and phosphorus, and metallurgical properties on ironmaking is described, and examples given for the relative value of haematite, Marra Mamba, and channel iron deposit (CID) ores.

Jul 11, 2011

By T A. Helms, P Gottlieb, S E, R Bateman

In response to the ever-increasing challenges facing the modern gold mining industry and the need for improved gold recoveries within all processing streams, CSIRO has upgraded its latest automated mineralogical analysis system, QemSCAN (formerly QEM*SEM), with special purpose hardware that speeds up the location and measurement of precious metal-bearing phases. By rapidly scanning the surface of polished blocks, and accepting only fields that contain the minerals of interest, QemSCAN is able to find, map, and quantify target minerals in extreme detail. Phase identification and quantification is achieved by placing a grid of points over the target particle and collecting X-ray information at each analysis point. The resulting mineral maps provide the metallurgist with a complete textural description of all gold-bearing phases within the product measured, together with quantification of the gold phases in terms of their modal abundance, particle size, mineral associations, relative contributions to gold deportment and liberation characteristics. Examples are presented which illustrate how QemSCAN is able to find and quantify gold-bearing phases within low-grade ores from the Super Pit, Kalgoorlie. This work is the result of a collaborative project between Kalgoorlie Consolidated Gold Mines (KCGM), CSIRO Minerals, and the University of Queensland, and is on-going.

Jan 1, 2000

By Showers JAF

The Western Mining Corporation mining lease on the Bendigo Goldfield measures 5krri x 18km with more than 20 anticlinal folds parallelling th long north-south boundaries. Numerous closely spaced shafts and extensive underground workings on the reef lines along the folds flooded with groundwater following the progressive abandonment of the field. Preliminary water sampling and assessment demonstrated that a major dewatering programme and acceptable disposal methods were necessary to dewater interconnected old workings in areas of interest prior to any underground work taking place. A field wide geohydolic investigation was undertaken to establish geohydraulic parameters, groundwater recharge rates and water qualities. Data from the field investigation together with estimates of the volume geometry of the submerged workings as obtained from old mine plans, production history, and limited pump testing results were used with an appropriate analytical model to obtain estimates of water discharge rates required to reach various dewatering targets. Water disposal options were limited by relatively high salinities, arsenic levels, contained hydrogen sulphide, and the mine locations within the urban areas surrounding Bendigo. Direct disposal to the surface drainage system could not be considered, treatment to acceptable discharge standards was not economically feasible, and it was necessary to adopt a strategy of collection, containment, and evaporation.

Jan 1, 1988