Search Documents

Sampling of CIL/CIP circuits is typically done by compositing samples of feed and tails over eight or 12 hour periods. As the residence time in the leaching tankage may be approximately 20 hours, the tails from any period being derived from material entering the circuit 20 hours earlier do not correspond to the head from the same sampling period. Moreover, mixing in the series of tanks in a circuit also modifies correspondence between input and output. A special purpose simulator has therefore been developed to allow for the mixing and delay in the tankage and permit estimation of the head assays corresponding to any tailings sample. Thus more accurate assessment of the day-to-day recoveries of gold and silver follows. The model, programmed in Excel, assumes that the tanks are perfect mixers. By inputting the sequential head grades and considering that no leaching has occurred, the head grade which corresponded to the tailings for each period could be estimated. Allowance is made for variations in feed rate over the sampling period by computing the average flow rate of slurry and thus the residence time of each increment of the tailings. This simple model and its application have been found to be subject to some limitations, which are discussed in the paper, resulting in some unresolved variability in results. However, for a typical circuit even the simple model was able to greatly improve consistency of recovery data with variations being approximately halved by eliminating much of the anomalous variation arising from the lack of correspondence between head and tail when changes in head grade are occurring. Therefore, this permits genuine variations in metallurgy to be identified with greater confidence and thus operational shortcomings can be identified and addressed more quickly.

Jan 1, 2006

By S Bluhm, LádeáOliveira, R Funnell

Taquari Vasouras potash mine (Vale Fertilizantes) has many interesting features including virgin rock temperatures of 50¦C at depths of 700 m. The mine has a relatively small shaft system with limited ventilation carrying capacity, which was not adequate to exploit the full extent of the deposit. This limitation was overcome by installing two large-scale recirculation systems with underground reconditioning centres. This paper describes this unique mine ventilation and cooling system and some of its history over the past two decades. The two controlled recirculation systems have been operating safely for some ten years and the use of large-scale recirculation has been a fundamental component in the increase of production and extending the mining further-and-further from the shaft centre. The recirculation systems have played a huge role in the mine profitability and comprehensively extending the mine life. The paper also discusses a number of novel design and operating features such as reverse running pumps for energy recovery. The underground chilled water system design required a number of special safety features in order to minimise the risk of water leakage since this could be catastrophic in a potash mine. This paper describes a good example of a mine in which the final ventilation and cooling system design ends up very different to what was envisaged at the greenfields stage.CITATION:Bluhm, S, Funnell, R and de Oliveira, L, 2013. Controlled recirculation and refrigeration at ValeÆs Taquari Potash Mine, in Proceedings The Australian Mine Ventilation Conference , pp 237-248 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D Tuazon, M Powell, M Ziemski, G D. Corder

Although mining companies have made broad corporate-level commitments to adopt sustainability, there continue to be problems when attempts are made to adopt higher-level sustainability aspirations and translate them into appropriate targets and methods at the more-specific operational level. The integration of sustainability principles into minerals processing operational decision-making processes has unique challenges that are not addressed adequately by current tools and methodologies, yet impacts from operational decisions can have longer-term effects realised at closure and rehabilitation.This paper describes a proposed methodology to achieve the integration of sustainability at the operational level through a systematic and rigorous process of identifying and qualifying sustainability issues and opportunities in an operation. The methodology, starting from a sustainability point of view rather than an operational one, guides the identification of process issues and opportunities by examining the operation, unit-by-unit, similar to a Hazard and Operability (HAZOP) process. Each issue or opportunity is qualified according to its measurability, scopes of impact and consequences so that it may be understood fully and the correct engineering problems are formed. Through improved decision-making to account for broader sustainability factors, operations can better address environmental and social expectations and pressures (both corporate and community, as well as immediate and in the longer-term), whilst still delivering on operational and business goals.The methodology has been tested with two case studies at minerals processing operations. At one site, the methodology identified a dust issue which had considerable business risks (loss of valuable product) compared to conventional engineering analysis processes. The other site also benefited from using the methodology as an opportunity to improve the operation of the milling and flotation circuits was identified. The opportunity not only showed a potential to improve operational efficiency, but also potential improvements in water and energy efficiency and a resulting increased resilience against water and energy supply risks. It was important to utilise the holistic approach of the methodology in the identification of opportunities at this site; the goals of the operation showed a strong coupling between water and energy issues which would be difficult to overcome using the operationÆs current organisational model, which deals with such issues separately of each other.CITATION:Tuazon, D, Corder, G D, Powell, M and Ziemski, M, 2012. A practical and rigorous approach for integrating sustainability principles into decision-making processes at minerals processing operations, in Proceedings Life-of-Mine 2012 , pp 233-242 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By E J. Sellers, A Cocker

Movement of the fragmented rock mass is an inevitable consequence of open cut blasting. Uncontrolled, unaccounted movement from blasting commonly causes ore loss and dilution from waste mixing. Therefore, the prediction of the post-blast location of both ore and waste is vital in grade control and of direct interest to mining geologists. Direct measurement techniques have matured significantly over the past decade, but their use remains expensive and labour intensive. Access and safety issues are further disincentives to regular movement monitoring. What is needed is a combination of direct measurement to establish baselines and reliable predictive modelling.The W H Bryan Mining and Geology Centre of the University of Queensland has pioneered 3D blast movement modelling using ‘physics engines’ to handle in-flight collisions and predict the final resting place of blasted material. Open cut metalliferous mines are a demanding environment for this style of modelling as they can involve complex geometries and variable buffering, which leads to inconsistent confinement. A version of the model designed to deal with these complexities is under development. A well-controlled field trial was needed to validate this new version.A validation trial was completed at a gold mine in South-East Asia. The aim was to increase throughput by increasing the blast powder factor without losing grade through dilution and mixing with waste. Four blocks were blasted to identify the effect of bench height and face confinement on ore movement, fragmentation and process throughput. The powder factor and blast timing were kept constant. Movement of the broken rock was measured by placing blast movement monitors at known positions in the block and then locating them after the blast. The majority of sensors were recovered, providing a unique insight into blast movement dynamics and generating a substantial data set for model validation.The model (called ‘MetaMove ‘) was calibrated for one blast and applied to investigate the extent of grade loss and possible mitigation strategies. Conventional mining techniques that involved firing across the strike of the orebody, and no post-blast boundary adjustment of the ore/waste boundaries prior to digging, were found to cause up to 44 per cent loss of high-grade ore, depending on the grade distributions. Post-blast adjustment of the ore/waste boundaries can negate this loss. The model indicates that altering timing and ensuring that the block boundaries are well confined can further constrain the movement of ore/waste boundaries. Thus, the model can be successfully applied to minimise grade dilution and limit misclassification of ore as waste whilst using higher powder factors to increase mill throughput. Application of a calibrated model to move ore/waste boundaries prior to digging will enable the production geology team to add significant value to the mining operation.CITATION:Cocker, A and Sellers, E J, 2014. Modelling blast movement for grade control at an open cut gold mine, in Proceedings Ninth International Mining Geology Conference 2014 , pp 377–386 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By D Kent, D Eisner

A lot of talk has been generated about the so called ‘Internet of Things’ (IoT) and its potential to transform the way we interact with our homes and devices. But the true potential and value of IoT is not going to be realised by the general consumer but by businesses.This paper outlines the application of IoT in mining and how it is a natural extension to the base networks becoming commonplace in both surface and underground mines. The potential for ubiquitous monitoring throughout a mining operation at low capital and support costs will transform the ability to monitor, analyse, report and manage all of the key processes involved in a mining operation.Importantly, the paper will discuss the practical applications that the IoT offers mining and explain how this really is transformative technology, not just the latest buzz words from the information technology (IT) world. If leveraged correctly the impact on mining, its cost base and efficiencies, is enormous.CITATION:Kent, D and Eisner, D, 2015. What the internet of things means to mining, in Proceedings Third International Future Mining Conference, pp 65–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M J. Nugus

The Geita gold mines in north-western Tanzania have produced 5 Moz of gold from an estimated endowment of 15 Moz. They are generally classified as typical Archaean orogenic banded iron formations (BIF)-hosted gold deposits in banded iron formations as described by Goldfarb, Groves and Gardoll (2001); Neall and Phillips (1987); Phillips and Powell (1993) and Neall (1987). The controls on gold mineralisation have been reassessed to conclude that Nyankanga, and we conclude that Nyankanga, the largest deposits within the group, developed during a dynamic and protracted deformation history intimately associated with several stages of hydrothermal fluid flow and alteration. The fluid-induced fractures associated with gold mineralisation are primarily manifested as submillimetre to metre-scale fractures and breccias developed preferentially in rocks that have been previously deformed and altered by silicification or seafloor metasomatism. This realisation detracts from the exploration and mining strategies that would solely concentrate on fluid pathways and associated wallrock alteration and veining solely within the BIFs as hosts for economic gold mineralisation.

Aug 22, 2011

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

By G J. Sparrow, M J. Fisher-White

A mineral and chemical characterisation study was conducted on ilmenite-rich heavy mineral concentrates sourced from the western sector of the Eucla Basin in southern Australia. Test work involved using X-ray diffraction (XRD), scanning electron microscope (SEM) and electron microprobe-based characterisation methods. Results showed considerable variability in the degree of ilmenite alteration between deposits with TiO2 contents varying from 53 - 63 wt per cent TiO2. Notwithstanding variability between individual deposits, the samples all had [Ti]/[Ti+Fe] ratios >0.5 consistent with a mineral assemblage of hydrated ilmenite or the hydrated, Ti-rich alteration phase pseudorutile (Fe3+2-x Ti3O9-3x (OH)3x). Accessory phases consisted of rutile (primary and secondary), zircon, aluminosilicates, quartz, Fe oxyhydroxides and spinels. Results for the most altered material are broadly comparable with data for ilmenite concentrates from the eastern margin of the basin. The mineralogy of the western Eucla Basin concentrates and the minor element composition of the ilmenite grains suggest they could be upgraded to synthetic rutile by a modified Becher process.

Jan 1, 2008

X-ray analysis of polycrystalline powder samples has grown beyond its roots in the world of laboratory research and is now regarded as one of the most powerful industrial process-control tools in the field of building materials. This is the key to characterise the element and crystalline phase composition of the material. This is due largely to the development of industrial X-ray analytical systems such as PANalyticalÆs twin solution, which has transformed the advanced analytical techniques born in the laboratory into a robust, workmanlike and easy-to-use tool for todayÆs heavy industries. The increasing use of alternative fuels makes the Bogue method less reliable. Therefore, the real phase quantification by the Rietveld method is the only choice. Additional fine-tuning of the Rietveld method by using alternative methods guarantees the most accurate quantitative results. Moreover, the recent development of ultra high-speed X-ray detectors allows for æon the flyÆ quantitative X-ray diffraction analysis and a truly interactive process and quality control.

Jan 1, 2008

By C Zschiesche, alam, A Abadias Llamas, A K

An integrated experimental and thermodynamic modelling study of the phase equilibria in the FeOFeO1.5- SbO1.5-SiO2 system in equilibrium with liquid Sb and Sb-Ag metal has been undertaken to develop thermodynamic model of the Na-Si-Fe-O slag system with S-Sn-Sb-Pb-As minor elements based on the experimental investigation of the selected sub-systems. New experimental phase equilibria data at 575–1600°C were obtained for this system using high-temperature equilibration of synthetic mixtures with predetermined compositions in sealed silica ampoules, Fe3O4 basket in sealed silica ampoule, or Re foils, a rapid quenching technique, and electron probe X-ray microanalysis of the equilibrated phase compositions. Experimental results on phase equilibria in the Fe-Sb-Si-O+Sb metal system obtained helped to produce initial set of model parameters in the slag. The primary phase fields of quartz/tridymite/cristobalite (SiO2), 2 high-SiO2 immiscible liquids, olivine (Fe2SiO4), wustite (FeO1+x), spinel (Fe3O4), schafarzikite (FeSb2O4) and valentinite/ senarmontite (Sb2O3) were identified in the binary Sb2O3-FeO, Sb2O3-SiO2 and ternary FeO-Sb2O3- SiO2 systems. Further refinement, particularly the distribution of excess Gibbs energy among the ‘FeO’-Sb2O3-SiO2 and ‘FeO1.5’-Sb2O3-SiO2 interactions, required the study at more oxidising conditions. Oxygen potential was increased using an inert metal (Ag) rather than using the gas flow due to the high volatility of Sb-containing gaseous species. Liquid Ag-Sb alloys with low concentrations of Sb of a few percent were used. At these conditions, the concentration of AgO0.5 in slag was below 1 mol per cent, which had a small effect on observed phase equilibria in the system. In addition, important information on the solubility of silver in slags is produced, which can be valuable when treating electronic recycling materials or primary silver-containing ores through the Pb process. Two main areas were addressed: the spinel-tridymite boundary (40–70 per cent SiO2 in slag) and spinel liquidus near 15 per cent SiO2 in slag. This allowed to deconvolute the separate contributions of the FeO-Sb2O3(-SiO2) and Fe2O3-Sb2O3(-SiO2) systems.

Jun 17, 2024

By E Amini, N Beaton

Application of ore pre-treatment technologies such as Grade Engineering and in-pit ore treatment require comprehensive analysis to show proven value is being generated by switching away from the current practices. Considering most mining operations last several decades; the pre-treatment technologies must be investigated over life of mine (LOM) to truly show value was generated or lost. Therefore, a value chain flowsheet model has been usually developed to run those analysis/simulations over LOM using a set of defined ore characteristics and the operating equipment capacities. The Integrated Extraction Simulator (IES) has been used for this type of LOM simulations as it has the necessary flexibility to accommodate the whole mining value chain flowsheet in one platform and provide essential computation power to run mass simulations for the given scenarios using the resource block model. This allows to forecast the value chain response over the LOM for all given scenarios in a feasible amount of time. The traditionally developed flowsheets for the analysis/simulations are usually limited to the mineral processing plant and were developed based on a single audit conducted on the plant in a very short time, e.g. several hours. The process plant is being operated with a certain ore at a certain condition during the short audits which would not reveal the true capacity of the operation equipment when ore characteristics changes. Therefore, it would be impossible to define the true capacity of the equipment and identify the constraints along the value chain. In this study, a methodology was developed to identify the constraints along the value chain and implement those in the IES flowsheet using process information. Also, the equipment models were fine-tuned to represent the true capacity of the equipment in the flowsheet using the same data set. The methodology was tested over five process plant in two operations and showed the performance forecast was significantly improved over the traditional methods being used so far. Then those high-fidelity flowsheets were used to evaluate the ore pre-treatment technologies proposed by the relevant resource company experts.

Nov 10, 2020

By I Gray

While in some cases it is vitally important to measure the virgin stress in rock prior to tunnelling there are a number of cases where such stress measurement is really not required. The concept of having to have a number to put in a numerical model representing a continuum is often quite inappropriate. This paper discusses the cases when virgin stress measurement is required and the most appropriate means to measure it. The techniques discussed cover all of the overcoring systems, hydrofracture and borehole breakout measurements. It also covers the use of rock surface stress measurement, which is easy to perform and should be used to check for changing stress conditions. Unfortunately this technique has been ignored in recent times because engineers are addicted to numerical models requiring far field stresses rather than measuring the real values that exist where they matter – at the tunnel wall. A case is presented in which the measurement of surface stress in a tunnel boring machine tunnel enabled the far field stress to be determined in what must be the world’s largest overcore.CITATION:Gray, I, 2014. The measurement of rock stress for tunnelling, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 153–160 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Underlain by and intruded into the sedimentary rocks of the Transvaal Supergroup the Bushveld Complex is the largest known layered intrusion in the world and contains one of the richest ore deposits on earth. It has been the world's major source of Platinum Group Metals (PGM) since the mid-1900s with Chromite and PGMs the two most economically important components of the Bushveld Complex. The lower group (LG), within the critical zone, consists of seven chromitite layers and it is within this sequence of chromitite layers, the most important target of the lower chromitite group is found, ie the LG6 chromitite unit. The LG6 chromitite unit consists of a chromitite duplex composed of the lower LG6 chromitite layer (Steelport seam), averaging 1 m thick, overlain by a 0.66 m waste parting and a thin 0.34 m thick LG6a chromitite layer (leader layer).Two mining methods are commonly applied in the Bushveld Complex to extract the LG6 chromitite layer package. One method consists of footwall development utilising rail bound equipment to gain access to the orebody and then extracts only the LG6 chromitite layer by means of hand held rock drills and scraper winches. The second method is the use of mechanised equipment to access the orebody on the plane of the ore utilising bord and pillar mining method, which extracts the full mineral resource, ie the LG6 and LG6a layers. Conventional narrow vein stoping is often selected due to the large conventional mining skills base found in South Africa, the perceived cost and dilution implications of utilising mechanised equipment, and the difficulties of using mechanised equipment at dips above 12¦. The driving factor for mechanised mining is the perceived ability to access the orebody quickly and inexpensively, and extract the entire mineral resource package (LG6 and LG6a) while limiting capital expenditure and improving safety.This paper investigates these two commonly applied approaches, highlighting the benefits and problems associated with the two approaches. Comparisons will be made of the two mining methods and recommendations given for the mining engineer to consider before selecting the appropriate mine design.

Dec 6, 2010

The low grade Mount Charlotte orebody was first mined with minimum capital expenditure by mechanised cut and fill stoping. The lower block was prepared simultaneously for open stoping by shaft sinking and installing another crusher and services. Similar development for the third block was discouraged by economic factors and reduced tonnage. Decline develop- ment required less capital and opened up ore reserves commensurate with advance, providing flexibility to stop operations without commit- ment: A 1 in 7 decline measuring 4.25m x 5.5m to accommodate standard Euclid 25 tonne dump trucks was developed south of the orebody. A fleet of four trucks average 12 loads each per shift over a haul distance of 700m.

Jan 1, 1973

By A R. Sale

This paper highlights two aspects of the mineral sands industry in Australia: the development of the industry from approximately 1870 through to 1980, and the author’s experience in the industry from 1966 to date.The first real heavy mineral (HM) mining in Australia started in 1870 with the mining of heavy mineral slicks on the beaches along the east coast of Australia. The real potential of Australian heavy minerals was however only realised in the 1920s with the first production of a heavy mineral concentrate that was shipped to Canada for processing. Post WW 11 and the Korean War, Australia was the largest producer of mineral sands products in the world as well as a significant developer of associated separation equipment and technology. The number of producing companies in the east coast peaked at 33 in 1957, was reduced to ten by 1965, and subsequently further reduced to five in 1980 as a result of potential mining areas being declared National Parks or Conservation Reserves. Today there is one company, Unimin Australia Pty Ltd (formally Consolidated Rutile Ltd) operating on the east coast. In contrast there were three companies on the west coast in 1965, four companies in 1980, and four companies today (albeit not the same companies).There have been considerable ups and downs for the industry in Australia, however world wide it was renowned in the past as being an industry that attracted numerous interesting and innovative characters that played a major role in developing it into the vibrant industry that it is today. This, given the current climate, is predicted to continue into the future.The author has been continuously involved in the industry for over 45 years from 1966, initially as an electrician at Consolidated Rutile Ltd culminating in the role of General Manager/President of Iluka Resources Limited USA, prior to his retirement in 2009. His exposure has been world wide and has covered all aspects of the industry but in the main focused on project development and operational areas. During this time there have been significant technological advances, yet to some extent the basic principles have not changed at all. Some of the most noteworthy advances include the development of the Wright Spiral in 1977, the development of the Reading High Intensity Wet Magnet (WHIMS), the rare earth magnets, the CRL floating thickener and the improvement of analytical techniques. From a safety, health and environmental perspective there has been significant advances that the industry has much to be proud of. These include wetland restoration both in Australia and in the US, the restoration of farmland in Virginia and Capel, and the re-establishment of native species, for example at Eneabba and Richards Bay to name but a few.

Oct 5, 2011

By P Martin, A Somarin, S Bailey

Field-based research was conducted to investigate the performance of field portable X-ray fluorescence (FPXRF) in the analysis of reverse circulation (RC) drill chips in iron ore exploration. For years, FPXRF has been considered unsuitable for iron ore exploration due to the limitations of the elements it is capable of analysing for, in particular its inability to measure light elements (Mg, Al, Si, P, S). With the advent of the use of silicon drift detectors (SDD) in FPXRF, light elements are now measurable elements. However, doubt over the appropriate use of this new technology still exists due to the absence of reliable comparative field data. These doubts concerned the ability of the FPXRF data to correlate strongly with the laboratory assay of the same samples. It was believed that inconsistent grain size and other variables not being controlled would contribute greatly to this perceived unreliability.We tested RC chip samples on-site in the Pilbara, with the portable Thermo Scientific Niton XL3t X-ray fluorescence (XRF) analyser for a range of elements including Fe, Mn, Al, Si and S and then compared the results with laboratory assay data. A strong correlation indicates that the FPXRF results are reliable. Furthermore, to show the effect of simple sample preparation, we also analysed pulps of the same samples in the same way.The correlations were good for all of the elements of interest for the RC chip samples (R2 values between 0.82 and 0.9), and excellent for the pulps (R2 values between 0.89 and 1). The results also showed a direct correlation between sample preparation and improved quality of results with the FPXRF. This indicates that FPXRF can produce data from unprepared RC chips for Al and Si that, when compared with laboratory assays, is reliable for a field application in drilling and grade control. CITATION:Somarin, A, Martin, P and Bailey, S, 2013. Non-destructive analysis of diamond core for light elements using Niton field portable x-ray fluorescence, in Proceedings Iron Ore 2013 , pp 117-230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By J Mar·n, R Anderson, S Strohma, R Harvey

Xstrata is the operator of both Minera Alumbrera Ltd (50 per cent Xstrata, 50 per cent Wheaton River) and Ernest Henry Mining Pty Ltd, (99.99 per cent Xstrata), both copper-gold deposits, using conventional SAG/ball milling at current capacities of 36 Mt/yr and 10.3 Mt/yr respectively. Alumbrera is located in Catamarca Province, in the north west of Argentina. Ernest Henry is located in Cloncurry, north west Queensland, Australia. Both operations started in late 1997, with commercial production achieved in early 1998. Different designs and equipment are in use for both operations, however the evolution of SAG milling performance, although logically related to their specific features, reflect similar trends of consistent increases in throughput. This paper will discuss the main changes to the SAG mill liners in both operations and the results achieved to date. A summary of the operating strategies will be included.

Jan 1, 2003

By Morinaga K

The optical basicity (A, Pb2+ as probe ion) of various oxide glass systems has been measured to establish the new basicity scale of slag melts. Best conditions of glassy fragments to measure A were as follow, (1) 1 ti 4 x 10-2 wt% Pb content, (2) 0.2 mm in thickness, (ii) enough annealing (about 10 hr) at a temperature 200¦C below Tg., and (4) polishing a surface well. the variation of A with composition was correlated to that of relative oxygen activity of slag melts. The estimation of basicity of slag melts from it could be valid. The A of opaque and coloured quenched slags could not be measured. An approximately linear relationship, however, exsisted between the isomer shifts (b) of Fe3+ ion in slag derived from the Mossbauer effect and A. Therefore, -4 of various metallurgical slag could be estimated from this relationship. These results can be expected to establish the new basicity scale of slag melts as the Louis basicity.

Jan 1, 1980

By G M. Jeffress, D C. Arne

There are two discrete aspects to collecting portable X-ray fluorescence (pXRF) data to obtain reliable results and to comply with reporting requirements under the 2012 edition of the JORC Code (JORC, 2012) – sampling method and quality assurance. A robust sampling program is required to obtain representative material for analysis. The appropriate method should be established for a particular project using a small orientation study. A variety of approaches to sampling soils, drill cuttings, rock faces and diamond drill core are discussed. These include using multiple spot analyses, scanning using a single operating beam and the collection of cutting saw pulps. The operator must also be aware of the attenuating effects of analysing through sample bags of different material types for various elements as well as the limitations of current pXRF instruments in reporting reliable data for certain elements. The analysis of the samples must also be accompanied by a quality assurance program in order to generate data that are ‘fit for purpose’. This includes recording X-ray tube resolution on a routine basis, using matrix-appropriate standards for which total elemental concentrations are available, using silica blanks, capturing sufficient duplicate analyses to constrain data precision and obtaining check assays to calibrate pXRF data against laboratory data. Examples of quality control approaches and data are presented. Table 1 of the 2012 JORC Code also recommends that information on instrument make and model, reading times and calibration be provided in any reporting of pXRF data. To this should be added information on operating mode and temperature, software version and moisture content of the samples. A robust sampling methodology with a suitable quality assurance/quality control program should produce pXRF data of sufficient quality for public reporting purposes, provided that the data are presented using appropriate cautionary language and adequate supporting information.CITATION:Arne, D C and Jeffress, G M, 2014. Sampling and analysis for public reporting of portable x-ray fluorescence data under the 2012 edition of the JORC Code, in Proceedings Sampling 2014 , pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014