Search Documents

By C. W. Tomlinson

The analyses which have been made by the writer according to the method described below were made as part of Professor Withey's investigation of the concrete aggregates1 of Wisconsin, in the hope of throwing light on the extent and nature of the influence of the mineral-ogical constitution of aggregates upon the properties of the concrete and mortar made from them. This method was found most satisfactory after four weeks of experiment and modification. It attains an accuracy quite sufficient for the purpose of the analysis, and is fairly rapid. mineralogical analyses may be thus made at a cost considerably less than that of chemical analyses of a similar degree of completeness. The results obtained by this method should not vary in any item by more than 1 per cent. of the total weight of the sample, and may be made very much better than this by the exercise of greater care in the microscopic counting (see below). The accuracy of the hand sorting is of course dependent upon the experience and carefulness of the analyst. After a month's practice, the writer was enabled to turn out these analyses at the rate of four in 33 hr. of working time. It was found most economical to handle four samples at once. The samples analyzed weighed from 290 to 340 g. each. The same method could be applied to larger or to smaller samples, within reasonable limits. The following list covers the necessary apparatus and equipment: 1 good balance capable of weighing accurately to tenths (or, better, hun- dredths) of a gram, and of handling quantities up to 200 g. in weight. 1 Westphal balance, registering densities to two or three decimal places. 1 Meker or Bunsen burner, and gas supply. 1 nest of sieves, 10, 20, 40, and 100 meshes to the inch.

Jan 1, 1916

By G. H. F. Gardner

The boundary conditions F = 1.0 and 4 = 1.0 (100 per cent) are dictated by the definition of F in the equation 1/F = aFp. These conditions have physical significance as the "limiting conditions" for the observed behavior in systems of dispersed particles. The other boundary conditions, cited by Gardner in his Eq. 3 as applying to this system, have no significance in the systems we studied. Maxwell's equation (Eq. 2) cited in Gardner's comments was developed for and limited to a regular, rather than random, dispersion of spheres which are sufficiently removed from each other so that they do not interfere with current flow about their neighbors. These restrictions also apply to Rayleigh's analysis. The title of Rayleigh's paper cited by Gardner is "On the Influence of Obstacles Arrayed in Rectangular Order upon the Properties of a Medium". He is not discussing randomly dispersed spheres. It might be inferred from Gardner's comments that Rayleigh specifically considered the differential equation (Gardner's Eq. 3). This is not the case. Mathematically, Gardner's Eq. 3 is exactly true for the system to which it applies, however, as both Rayleigh and Maxwell note that their equation for F in terms of F is not for randomly dispersed spheres. At the time we wrote our paper, we were aware of the work of Wyllie and Gregory as cited by Gardner. We cited their work in Ref. 5 of our paper. Our comment on page 287 of the paper about the validity of an m value of 1.3 for spheres with a porosity of 38 per cent remains as our answer to Gardner's question on this point. Our data, at 38 per cent porosity, show that the condition a = 1 and m = 1.3 holds for spheres near 40 per cent porosity.

By H. D. Kynor

By the term mechanical mining is meant that operation, or series of operations, that replace the hand methods of mining. The first undercutting machine to operate in anthracite was placed in the Butler mine of the Hillside Coal and Iron Co., Dec. 23, 1910, by the Sullivan Machinery Co. The first Jackhamer used in the anthracite field was installed at the Wadesville colliery of the Philadelphia & Reading Coal and Iron Co. in Oct., 1912, by the Ingersoll-Rand Co. The first longwall conveyor was installed at the Dodge mines of the Delaware, Lackawanna, & Western Coal Co. in March, 1912. The first mechanical scraper equipment was installed in the Seneca mines of the Lehigh Valley Coal Co. in January, 1914. The amount of anthracite mechanically mined since the first mining machine was installed in 1910" is as follows: Penna. Coal Co. D. L. & W.. ScRanton Temple Hudson YeaR and Hill- Tons Coal Co., Coal Co., Coal Co., Total, side Coal Tons Tons Tons Tons and Iron. Tons 1920................ 372,737b 367,000d 322,892 74,127 371,878 1,508,634 1919................ 950,786 no record 306,616 81,575 319,356 1,658,333 1918................ 917,778 744,966 24,880 44,756 288,781 2,021,161 1917................ 757,940 838,800 5,050 57,279 164,180 1,823,249 1916................ 286,780 860,663 13,960 114,173 101,475 1,377,051 1915................ 428,819 592,169 8,253 1,029,241 1914................ 219,188 153,896 373,084 1913................ 171,505 1912................ 124,267 124,267 1911................ 40,319 40,319 1910................ 1,184 1,184 a A slightly greater production was obtained than here indicated, as the tonnage from individual operations is not shown. b Decrease due to strike conditions in 1920. c Does not include tonnage of D., L., & W. d D., L., & W. decrease in 1920 due to having fewer mining machines in operation. There are about 150 undercutters in use in the anthracite region, 80 mechanical loaders, and 10 longwall conveyors.

Jan 1, 1922

The amendment to Article III, Section 1, of the Constitution, raising the dues from $10 to $12 a year commencing in 1917, which was submitted to the members for letter ballot, was passed by a vote of 1,039 to 401.

Jan 4, 1916

By Edmund D. North

In making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

By H. R. Fife

AN extended study of dustproofing Freeport-seam coal has empha-sized several fundamental features in the successful treating of bituminous coals. The extent of the exposed surface area and its absorption proper-ties for the dust-retaining film were found to be the most critical factors affecting the efficiency of fly-dust prevention. From recently published screen data and specific surface-area measure-ments on United Kingdom coals, an approximation of the surface exposed by mine-run coal and by 1-in. slack was made. The total surface area exposed by an average ton of this mine-run coal was estimated at 3768 sq. yd., while a ton of 1-in. slack represents a total surface area of 8779 sq. yd. with no additions for porosity. It is important in coal treating to consider that in mine-run coal the fraction above 1/4 in. in size represents 79.5 per cent of the total weight, but only 4 per cent of the total surface, while the fraction below 150 mesh contains 47 per cent of the total surface and only 1.2 per cent of the total weight. Also, one should appreciate that, in a 1-in. slack, the domestic stoker fraction (1 in. to 8 mesh) contains 76.3 per cent of the weight and 8.2 per cent of the surface, while the fraction below 150 mesh represents 3.3 per cent by weight and 54.8 per cent by sur-face area. Wax extraction data on 1-in. to 0 slack from mine-run treated Free-port-seam coal showed that the coating was distributed uniformly as a function of exposed surface; hence, nonuniformly on a weight basis. This distribution of the coating on mine-run coal therefore limits the extent of treating that is desirable on bituminous coal at this point in the preparation. The treatment of Freeport mine-run coal before it reached the tipple gave a 70 to 80 per cent reduction of fly-dust in the tipple, a satisfactory treated commercial slack coal, and an indicated change in the trend of tipple degradation. The premium-treated domestic sizes required a supplemental treatment for complete dustproofness.

Jan 1, 1937

By John R. Hutchins

1ms is a report of nickel (wire) oxidation studies designed to test the validity of Valensi's1 equation developed for the kinetics of a reaction controlled by diffusion in a continuously growing product layer on cylindrical surfaces. The equation is:

Jan 1, 1968

The following list contains the names of members of whose deaths notices have be received at the Secretary's office between Jan. 1, 1935, and April 1, 1936. Bio¬graphical sketches published in MINING AND METALLURGY are indicated in the last two columns.

Jan 1, 1936

By W. G. Wender

The North Central Texas district, as known to the oil fraternity, is the area producing from sands and limes of Pennsylvanian age, roughly embracing the territory lying between Fort Worth and Abilene in an east-west line, and between the Red River and the Llano Mountains in a north-south line. The history of oil development in North Central Texas during the year 1927 is briefly reviewed in the following paragraphs. Brown County New discoveries and development in Brown County centered mainly around the Fry pool, located in the west central portion of the county. Important discoveries for the year were: Shoupe No. 1 John Byler, discovery well of the Byler pool, located 2 miles south of the Fry pool which camc in early in February, 1927, at 1262 ft. for 90 bbl. in the Fry sand of upper Strawn (Pennsylvanian) age. Rosenfield No. 1 P. Davis, discovery well of the Smith-Ellis pool located 1 1/2 miles northeast of the Fry pool, came in March 7, in the Fry sand from 1277 to 1279 ft. for 30 bbl. initial. Pandem Oil Corpn. No. 1 Mrs. T. Hutton, located 1 mile east of the Smith-Ellis pool, came in in December in the Fry sand from 1119 to 1130 ft. for 45 barrels. The Fry pool passed its daily production peak of 25,000 bbl. during the first part of June, and declined to a daily production of 5100 hhl. by the close of the year. The oil recovery from the Fry pool up to Jan. 1, 1928, slightly exceeded 4,000,000 bbl., averaging 4700 bbl. to the acre. over the entire pool. The Smith-Ellis pool passed its daily production peak of 5300 bbl. in Octohcr, 1927, and dropped to 3600 bbl. by the close of the year. The possibilities of the Byler pool will be unknown until the area is fully drilled up. In the Blake pool, production passed 2,500,-000 bbl. for the year. The per acre recovery in this pool up to lkc. 31, averaged slightly over 5000 barrels.

Jan 1, 1928

By NATHANIEI HERZ

(Cleveland Meeting, October, 1912.) THE formula very frequently used for computing the economical size of pipe to transmit compressed air is that of D'Arcy, as follows: d5(p1-p2)/w1l D-c w11 Where, D = the volume of compressed air delivered in cubic feet per minute,-at the final pressure. c = an experimental coefficient determined for the various sizes of pipe. d = the diameter of the pipe in inches. 1 = the length of the pipe in feet. P1 = the initial gauge-pressure in pounds per square inch. p2= the final gauge-pressure in pounds per square inch. W1 = the density of the air, or the weight in pounds per cubic foot at the initial pressure, p,. The most common case is that in which the given quantities are: the quantity of air required, the length of the pipe, and the initial pressure. The method of solution is to assume a pressure-loss and to compute the remaining factor, c/d5, thus giving the size of pipe corresponding to the assumed loss of pressure. It is always desirable to try two or more pressure-drops, in order to find the combination that is most satisfactory, since often a small change in the size of pipe will reduce or increase the loss of pressure several pounds. An alternative method is to assume a size of pipe and calculate the corresponding pressure-drop. Each method involves a series of tedious calculations to arrive at the most economical solution, and also requires the use of tables giving the constant, c, the actual diameters corresponding to the nominal pipe-sizes, the density of the air, w1, and often, for convenience, a table giving the

Dec 1, 1912

By R. W. Brauchli

The author has made a statistical analysis of the relations between recovery and length of cores, diameters of cores and of drill pipe, and cost of coring under different contractual conditions. The data are presented in tabular form. The length of the core appears to play a minor part in the percentage recovered, with a tendency to lower percentages with increased core length; approximately 50 per cent of the length cored is normally recovered if the cores are more than 2 in. in diameter. The diarneter of the core has a more pronounced influence on the recovery; 1 3/8-in. cores average 29.1 per cent, 2 1/8 -in. core 53.4 per cent and 3 1/8-in. cores with 6 5/8-in. drill pipe 68.5 per cent. Where 31/8-in cores were taken with smaller diameter drill pipe, i. e., 4 1/2 - in. drill pipe in 8 1/4-in. hole, the recovery dropped to 49.8 per cent, indicating that the more rigid drill pipe favors good core recovery, a conclusion also borne out by the results obtained in using large drill pipe for smaller diame-ter cores. Surprisingly good recoveries were obtained from both the Johnson and Simpson sands; shale, limestone and dolomite each gave less then average recoveries. No serious fishing jobs resulted from coring operations. Attention is called to the need of a core drill which will make it possible to drill a full-sized hole while coring, and thus reduce the cost of cores. Data pertaining to core drilling should be consistently recorded, such as, diameter of drill pipe and collar, diameter of core, recovery, size of cutter heads, type of core-barrel, coring time, speeds of rotation and of pumps, weight on core-barrel, etc.

Jan 1, 1933

By W. D. Donnelly, M. L. Rudee

THE crystallography and morphology of ?-Al3Fe precipitates in an A1 + 0.5 wt pct Fe alloy have been studied by transmission electron microscopy. The alloy was cast in cylindrical ingots, 15 cm in diameter and 60 cm in length, and cooled slowly. The measured composition was 0.527 wt pct Fe, 0.001 wt pct Mg, and 0.003 wt pct Cu. Spectrographic analysis revealed no additional trace impurities. Thin slices were cut from the ingot and reduced by more than 95 pct by rolling to a thickness of 0.1 mm with no intermediate annealing treatments. These thin sheets were then vacuum-annealed for 1 hr at 612°C and air-cooled in their capsules. Thin foils for examination in the electron microscope were prepared by electropolishing. The precipitate is found in the form of oval platelets on the (110) planes of the matrix. The major axes of the platelets are parallel to the (110) directions of the matrix, and vary in length from 1/2 to 2 p. The thickness is about 1/10 µ. Examples of platelets, both in the plane of the foil and normal to the foil, are shown in Figs. l(a) and l(b), respectively. lack' found that ?-A13Fe (more correctly Al13Fe4) belongs to the monoclinic system. Using Black's structural data and simultaneous electron-diffraction patterns from the matrix and precipitates, the habit planes and directions were determined to be: (001)? 1 (110)Al [100]?|| H [001]Al The orthogonal crystallographic axes of the precipitates are accurately in the habit plane, while the measured coincidences of the directions are only within 10 deg. The major axis of the platelet is parallel to [010] in the 0. This orientation corresponds to the direction of nearest registry of the lattices.

Jan 1, 1964

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4O10(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. SOURCES At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This

Jan 1, 1940

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth, W. L. Finlay

Titanium with up to 7.5 pct Al forms single-phase a alloys that are work hardening, not heat treatable, and ductile as welded. The high aluminum Y phase alloys are not usefully ductile, despite their low hardness, but they have excellent oxidation resistance and hot hardness. LITTLE has been published on the effect of aluminum on the mechanical properties of titanium, despite the fact that two of the first four commercial alloys released by titanium alloy producers contained aluminum as an important alloying ingredient. These were both a-ß type alloys, one containing 4 pct A1 and 4 pct Mn and the other containing 3 pct A1 and 5 pct Cr. However, neither of these alloys reflects the true alloying nature of aluminum, since each contains important amounts of the ß-stabilizing addition, manganese or chromium. In a previous publication on the constitution of Ti-A1 alloys,' the authors showed that aluminum had a high solubility in a titanium and was strongly a stabilizing in nature. About 25 wt pct A1 is soluble in a titanium at room temperature. With as little as 5 pct added aluminum, the a transus temperature is increased from 882" to 970°C, and the correspond- ing ß transus to 995°C. The first intermediate phase in the Ti-A1 system is the ordered face-centered tetragonal TiAl phase, which extends from 34 to 46 wt pct Al. The present paper presents hardness data over the entire titanium-rich region of the system, through the TiAl phase, and mechanical property data on the alloy range capable of being fabricated. Methods of Investigation The materials used and general preparation of alloys, as well as experimental techniques used in the investigation of Ti-A1 alloys, have been adequately described.' Briefly, the preparation consisted of arc-melting the desired amount of high purity aluminum (99.99 pct purity) and iodide titanium (maximum hardness 100 Vickers, as deposited) together on a water-cooled copper hearth under a partial pressure of argon. The resulting button ingot was of such form that it could be fabricated without further treatment. All work was done using ingots weighing 10 to 15 g, which were hot-rolled to strip form whenever possible. Tensile samples were 3.25 in. long, 0.5 in. wide, and 0.040 in. thick, with a reduced section 1.25 in. long by 0.250 in. wide. The gage length used was 1 in. Electrical strain gages mounted on the

Jan 1, 1954

By J. D. Pelletier

SAN MANUEL orebody is a disseminated copper deposit in quartz monzonite, monzonite porphyry, and diabase. Quartz monzonite, which is Pre-Cambrian1 in age, is exposed in an area including No. 1 and No. 4 shafts and extending about 2400 ft southeast from No. 1 shaft. It is also exposed in the bottom of No. 2 shaft and in a zone roughly 500 to 1200 ft southeast of No. 2 shaft having its long dimension along a northeast-southwest axis. Churn drilling has shown all these exposures to be parts of a contiguous mass of quartz monzonite lying within and beneath the ore zone.

Jan 7, 1957

By E. W. Dewing

ROLIN1 in 1961 published a phase diagram for the CaF2-Na3AIF6 system in which substantial (-20 wt pct) solid solubility of CaF2 in Na3A1F6 at the eutectic temperature (945°C) was indicated. The evidence was that the halt in cooling curves associated with the eutectic was lowered progressively on the Na3AlF6 side. H olm2 has recently confirmed the experimental fact, but attributes it to evaporation losses shifting the composition into the ternary NaF-CaF2-Na3A1F6 system with a consequent lowering of the eutectic temperature

Jan 1, 1970

By L. F. Mashburn, T. J. Ferree

A Reichert cone concentrator was installed in an aggregate plant circuit to recover the extremely fine "flour gold" known to exist in the deposit. The gold content of the bank- run gravels averages about 0.1 g/t-about $1.29/t, based upon $12.86/g ($400 per oz) gold. The fineness of the gold averages between 950 and 960. The Reichert cone, in conjunction with a conventional shaking table, recovers in excess of 85% of the gold. A screen analysis of the gold particles shows 44.1 % is - 74pm (-200 mesh) in size. The plant operates with a two-man crew.

Jan 1, 1983

By EDBIUND U. NORTH

IN making a glass model of mine-workings, each mine will present some little individualities, to meet which will call for the exercise of special ingenuity. Having made several models, I offer the following details of the model of the Montana-Tonopah mine-workings, believing that with small changes for different conditions the method described can be successfully used in making a glass model of the workings of any mine. The model, Fig. 1, has the top, one end, and the front removed. The case is made of kiln-dried pine, painted with several coats of dead-white paint. It is made to take sheets of glass 24 by 42 in. in size, and is 18 in. high, the workings shown being on a scale of 1 in. = 40 ft., or 4800 : 1 scale. The base is made of four pieces of 2-in. material, well pinned and glued together. The back, of material 1 in. thick, is secured rigidly to the base by screws and countersinking. The four posts, 1.5 in. square, are so cut that. the front and two ends of the model fit in flush with the outside edges of the posts. The top rails, 1 in. square, are fastened rigidly to the front and back posts by means of small iron braces. The ends, front, and top of the case are of 0.5-in. material; the ends and front are held in place at the bottom by pegs fitting into the base ; at the top the ends are held by buttons and the front by cupboard-hooks on the inside. Hinged hasps on the cover, fitting over staples in the end-pieces, make it easy to lock the entire case. Before the back is fastened to the base, it is cut with horizontal and vertical grooves to receive the horizontal and vertical sheets of glass, shown clearly in Figs. 1 and 2. The horizontal grooves, spaced to scale, represent the vertical distances between the levels at the shaft. The vertical grooves are placed wherever cross-sections of the workings are desired.

Jan 1, 1910

LINN BRADLEY, H.' D. EGBERT and W. W. STRONG (communication to the Secretary*).--In the discussion of the paper, a request was made for a further explanation of the curves given on Chart I. In preparing the curves given on this chart, a typical blast-furnace top gas having the following composition by weight was assumed: Per Cent. C02 21.00 CO 24.00 Hz 0.25 CH4 0:25 N2 54.50 For any given top-gas temperature, Curves A, B, C, D, and E indicate in British thermal units the sensible heat lost in cooling the top gas to 60° F. by wet-cleaning methods. Top-gas temperatures are plotted as abscissae, sensible heats above 60° F. in British thermal units are plotted as ordinates, and separate curves are drawn for top gases carrying various amounts of moisture. For any given stove exit-gas temperature, curves A1,-B1, C1, D1, and E1, indicate in British thermal units the sensible heat carried out of the stoves by the moisture which is left in the top gas when it is dry-cleaned and enters the stoves hot. This moisture is removed when the gases are wet-cleaned and the sensible heat which it carries out of the stoves is therefore saved. As before, separate curves are drawn for top gases carrying various amounts of moisture. The curves in Fig. 1, therefore, indicate graphically how much more sensible heat is conserved by cleaning the top gases by the dry-hot method than is conserved by cleaning the top. gases by a cold-wet method and thus removing the greater part of the moisture carried by them. They also show of how little moment it is from a heat conservation standpoint whether or not the moisture carried by the top gases is removed before they enter the stoves. That wet cleaning secures the removal of this moisture and is thus to be recommended from a heat conservation standpoint is an argument often advanced by advocates of wet cleaning. The curves of Fig. 1 show how fallacious such an argument is.

Jan 6, 1917

By B. C. Craft

Development and exploratory work in Mississippi during 1934 was rather active, resulting in the expansion of the proven area and the drilling of a number of important wildcat wells. Mississippi showed a decrease in drilling operations during 1934. There were 36 completions from 18 counties during this period compared with 58 completions from 22 counties during 1933. There was a considerable decrease in activity in the Jackson gas field in Hinds and Rankin counties with only 9 completions, resulting in 8 gas wells and 1 dry hole compared with 17 gas wells, 2 oil wells and 7 dry holes during 1933. Leasing and geophysical work was reported from several sections of Mississippi last year. Extensive exploration and drilling were carried on in Lamar, Hancock, Pearl River, Greene and Stone counties and on the flanks of the Jackson anticline. Exploration will be continued in these areas during 1935. Four important wildcats were completed during 1934, all of which were reported as being structurally high, but without having important shows of oil or gas. These tests were: Hix and Germany's, J. J. Newman Lumber Co. No. 1, sec. 21-4N.-15W., Lamar County, abandoned at 3520 it. in the Wilcox; United Gas Public Service Company's Davis No. 1, sec. 30-1N.-5W., Greene County, abandoned at 7439 ft.; Gulf Refining Company's May L. Williams No. 1, sec. 33-5S.-17W., Pearl River County, abandoned at 4800 ft.; and Clarke County Oil Company's S. B. Kirkland No. 1, sec. 10-2 N.-16E., abandoned at 4002 ft. in the Eutaw. Another interesting wildcat was Gulf Refining Company's Dantzler Lumber Co. No. 6, sec. 22-4S.-llW., Stone County, abandoned at 7700 ft. (according to reports below the Selma chalk). A total of 114 of the 132 gas wells completed in the Jackson gas field are still producing and have a combined open-flow capacity of 4,145,-696,000 cu. ft. Four of the abandoned gas producers were never connected to the lines. The open-flow capacity of three wells in the Amory field is approximately 1,000,000 cu. ft. Producing against a line pressure of 50 lb., the demand during December greatly exceeded the capacity.

Jan 1, 1935