Search Documents

What has happened to the basic coal industry during the past year? Has it been a better year for coal than 1961? What striking new developments have occurred in mining, preparation and utilization? Are there positive signs that production will go up? What has happened in the utility market, the metallurgical market and the export market? Is the controversial question of coal transportation nearer to a solution? What progress has research made for coal during the year? The answer to these and many other important questions are offered in the following review of the Coal Industry-1962.

Jan 2, 1963

By Leo Horvitz

PETROLEUM and natural gas are composed principally of the saturated hydrocarbons ranging from methane, the lightest, to nonvolatile liquids and solids containing approximately thirty-five carbon atoms. A technique for locating buried accumulations of these hydrocarbons before drilling obviously requires that some of the hydrocarbons leave the deposit and migrate toward the surface of the earth where they may be detected in their original form. Earliest attempts to link near surface hydrocarbons to petroleum at depth were apparently made by Laubmeyer1 in Germany and by Sokolov2 in Russia. These investigators collected samples of soil air from boreholes one to two meters deep and analyzed them for traces of hydrocarbons. They found that soil air over producing areas is richer in these constituents than is soil air over barren areas.

Jan 12, 1954

By R. J. Grissom

PHOSPHATE deposits have been worked in many countries of central and south central Tennessee, but only ht ebrown rock deposits of Maury and Giles Counties will be discussed at any length in this articles, as all of the major opeations are now located there. They are: Mt. Pleasant District-Federal Chemical Co., Hoover and Mason Phosphae Co., International Minerals and Chemical Corp. (Maury and Giles Counties), Virginia-Carolina Chemical Corp. (formerly Charleston Mining Co.), and Victor Chemical Co. Columbia District-Armour Fertilizer Works and Monsanto Chemical Co. In the near future, the well-known, extensive deposits of blue rock in Lewis and Hickman Counties,also the brown rock in Hickman, Willamson, Summer and Davidson Counties, will again come into production. Certain physical peculiarities of the Tenessee deposit have played an important part in the design and use of mining and milling equipment.

Jan 1, 1944

By J. F. Breedis

The morphology and crystallography of marten -site formed during quenclzing were examined by transmission electron microscopy in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pet Ni and Fe-33 wt pet Ni. Depending upon composition, four types of transformation products were observed in this portion of the Fe-Cr-Ni system. Three of these products are denoted as lath, plate, and surface martensite. The hcp structure found in association with martensite it? certain higlz-clzromium stairzless steels does not influence the transformation crystallogyaphy and cannot he Considered to act as a transitional structure in the transformation from austenite to martensite. DISTINCT changes in the characteristics of mar-tensitic transformations are produced by the partial replacement of nickel by chromium in austenitic iron alloys. Large, discrete martensite plates form in Fe-30 pct Ni, while aggregates of small crystals form in sheets parallel with (111)A austenite planes in stainless steels containing in the vicinity of 18 pct Cr and 8 pct Ni. These transformation structures are termed plate and lath martensite, respectively. In addition, an hcp structure (E) has been observed in certain high-chromium stainless steels in association with martensite. It has been suggested that the E structure acts as an intermediate step in the nucleation of martensitel-' and influences the morphology and crystallography of the final transformation product. However, this structure may be the consequence of the deformation of austenite arising from the shape distortion accompanying the transformation to bcc martensite.' An hcp stacking of atoms is produced in an fcc lattice by the introduction of an intrinsic stacking fault on alternate (111)A planes. At present, the arguments behind each explanation for the E structure are based on circumstantial evidence. This investigation seeks to determine the importance of the hcp structure to the martensitic transformation, and to examine the crystallography and morphology of the structures produced in bulk samples by quenching in alloys whose compositions lie between Fe-19 wt pct Cr-11 wt pct Ni and Fe-33 wt pct Ni. These aspects of the martensitic transformations occurring in these alloys have been studied by electron metallography and selected-area diffraction of foils examined in transmission in the electron microscope. EXPERIMENTAL METHODS The alloys have been prepared from thoroughly mixed powders of pure iron (99.6+ pct, 0.06 max pct C, 0.15 max pct N), chromium (99.9+ pct), and nickel (99.9+ pct). After sintering in an Ar-H2 atmosphere, the mixtures were melted by induction heating in recrystallized alumina boats under purified argon. The ingots were cold-rolled to 0.4-mm sheets (100 pct reduction in thickness) after the removal of at least 1.5 mm from their surfaces by grinding. Three-millimeter discs were punched from the cold-rolled sheet and annealed at 1150°C for approximately 24 hr in evacuated quartz capsules. The average grain size was 40 µ Thin foils for examination in transmission in the electron microscope were prepared from discs quenched to liquid-nitrogen temperature. A depression was first jet-machined into the center of a disc and a thin area (less than approximately 3000A in thickness) was produced at the base of the depression by electropolishing. Electron-microscope studies utilized the RCA EMU-3 and the Philips EM-100B microscopes operating at 100 kv. X-ray examination of the polycrystalline alloys was performed either in a diffractometer or in a

Jan 1, 1964

By M. J. Coolbaugh

Mining of potash more than 3000 ft beneath the water-bearing sediments in Saskatchewan presented the unique challenge of designing stable mine workings and assuring protection from overhead water in a material that was believed to flow plastically, but whose behavior as a plastic material was not sufficiently known. Under the stress conditions ordinarily encountered in mining most rocks behave as elastic materials; that is, they compress slightly under pressure, and rebound when the pressure is released. Salt and potash, however, are different. Even under the relatively low pressures encountered at shallow depths, these materials become slightly plastic and yield to stress by flowing.* The plastic properties become more pronounced at greater depth and pressure, and the question arises as to whether or not the plastic flow will be rapid enough and exert enough pressure to destroy underground structures or interrupt the mining process.

Jan 5, 1967

By J. Paces, E. Miller, K. L. Komarek

The resistivity was determined as a function of temperature over the composition range from pure cadmium to 40 at. pct Cd. Melts with cadmium contents less than 85 at. pct had negative temperature coefficients of resistinity. On cooling below a transition temperature close to the liquidus temperature, the slope of the resistivity-temperature curve changed sharply. The activation energy calculated from the slope was 0.07 ev above the transition temperature and 0.14 ev below. The resistivity vs composition curve shows two maxima corresponding in composition approximately to CdSb and Cd3Sb2. THE relationship between the structure of a liquid and that of the crystal formed on solidification is at present not well-under stood. Various experimental determinations of the properties of liquids indicate that deviations from random atomic arrangements in liquids occur and that the properties of a solid and of its melt are closely related. Thermody-namic activities of liquids usually show negative deviations in systems where compound formation occurs in the solid,' and X-ray data indicate that close-packed solids and their melts frequently have nearly the same coordination number. Electrical resistivities and viscosities of liquids frequently exhibit maxima at compositions corresponding to compounds in the solid state. It should be of interest to study systems which have both stable and metastable compounds in the solid, and to determine if the short-range order in the liquid is affected by the existence of the metastable solid phase. The Cd-Sb system exhibits such a metastable phase. The phase diagram is shown in Fig. 1.3 The stable system has one intermetallic compound, CdSb, crystallizing in the orthorhombic crystal structure, with a melting point of 456°C. The metastable system also has one compound, Cd3Sb2, melting at 420°C and crystallizing in the monoclinic structure. Metastable alloys transform to the stable crystal structure in the temperature range from 250o to 350°C. Several distinct indications of very strong short-range order in the liquid phase have been reported in this system, with a close relation between the ordering in the liquid and the existence of both the stable and metastable solid phases. Scheil and Baach4 have observed distinctly different vapor pressures for liquid Cd-Sb alloys depending on whether the liquid solidified to the metastable- or stable-phase configuration. They observed an unusually sharp increase of the activity in a limited temperature interval immediately above the liquidus temperature of stable alloys, followed by a sudden decrease in slope to what they considered normal values. On cooling, the activity data reproduced the values in the normal range but then deviated from the values obtained on heating. They also observed that specimens of the stable phase upon melting and resolidifying always crystallized in the stable crystal structure as long as the melt was not heated to more than 485° to 525°C; otherwise solidification to the metastable phase occurred. However, in a later investigation, these results were not reproduced (13). The resistivity of liquid Cd-Sb alloys has been investigated by Matuyama 5, Oleari and Fioram, 8 and Belaschenko (141, but only above 500°C, the temperature region where Scheil and Baach observed no vapor-pressure anomalies. The data of Matuyama and of Oleari and Fiorani are reproduced in Fig. 5 and show a maximum in resistivity at 50 at. pct Cd. The data of Oleari and Fiorani, however, show the maximum as being rounded, and their values in general are slightly higher than those of Matuyama.

Jan 1, 1964

By D. T. Peterson, F. A. Schmidt, J. D. Verhoeven

The velocity of mig-ration of these solutes in thorium metal due to a high amperage dc current was measured at several temperatures. All three solutes migrated in the same direction as the electron flow. Diffusion coefficients were combined with the migration velocities to predict the steady-state concentration profile. Electrotransport was shown to be an effective method of removing carbon, oxygen, and nitrogen from thorium and resistance ratios several times larger than for crystal bar thorium were achieved. However, the maxirnum attained purification was well below the predicted values, apparently due to some form of contamination. THE migration of solutes in metals when a high current density dc current is passed has been known for many years. This phenomenon has been the subject of a number of reviews published in recent years.l~* Many of the earlier investigators of electromigration of interstitial solutes interpreted the direction and velocity of migration on the basis of a charge on the solute particle. This interpretation is unclear because, in a given experiment, one cannot separate the contributions to the force moving the solute which arise from the charge on the solute in an electric field gradient and the momentum transfer from the scattering of the electrons or holes. There have been only a few quantitative measurements of interstitial migration velocities and some of these have been characterized by poor accuracy or by errors in the analysis of the experiment. The electrotransport mobilities of carbon, nitrogen, and oxygen in thorium were determined by observing the rate of movement of a discontinuity in the concentration profile. This method was used by Carlson el a~.~ to determine the mobilities of interstitial solutes in yttrium and its advantages are discussed in that paper. The specimen is essentially a pair of semi-infinite, bar-type diffusion couples. The electro-transport velocity was measured by observing the displacement of the mean concentration point in a measured length of time. The diffusion coefficients were calculated by the Grube method from the concentration profile. The transport mobilities and diffusion coefficients can be used to predict the concentration profile in an electrotransport experiment of a given time, current density, and specimen length. At long times a steady state will be reached such that the natural logarithm of the concentration of each solute varies linearly along the bar with a slope which is equal to the velocity of the migrating solute divided by its diffusion coefficient. The estimation of the purification potential of electrotransport is discussed by ~erhoeven.' A comparison of the concentration profile and the purification which should be expected from known solute velocities and diffusion coefficients with that which is obtained in an experiment can be very useful in indicating whether the maximum possible purification has been achieved. EXPERIMENTAL METHOD The apparatus used in this study consisted of a sample chamber which was equipped with two electrodes, a sight glass, and a flange for mounting to a high-vacuum system capable of obtaining pressure of 2 x lo-? Torr. The chamber was made of stainless steel and was 4 in. in diam and 6 in. long. The seal between the electrodes and the chamber was made with "0" rings and compression bushings. The thorium specimens were threaded and screwed into tantalum "U"-shaped adapters attached to the ends of the electrodes. This arrangement is shown in Fig. 1

Jan 1, 1967

By W. D. Robertson, R. E. Reed-Hill

DEFORMATION of magnesium crystals in a direction parallel to the basal plane has a special significance as a result of the preferred orientation characteristic of cold worked and recrystallized polycrystalline magnesium sheet and extruded rod in which the basal plane tends to lie in or near the plane of the sheet or the axis of a rod. The principal objective of the present study is a determination of the modes of plastic deformation in magnesium single crystals in this orientation. Evidence for nonbasal slip in magnesium has been presented by a number of authors. Schmid and Was-serman&apos; indicated that pyramidal slip on {1011} < 1120> or {1012} <1120> could occur above 225°C. Bakarian and Mathewson2 stablished that the slip system {1011} <1120> operates at high temperatures and that 225°C was a lower limit for pyramidal slip. The latter authors also showed that the critical resolved shear stress for {1011} slip was 400 g per sq mm at 330°C, while that for basal slip was 66 g per sq mm at the same temperature. Thus, at 330°C basal slip should be expected for all orientations except those in which the stress axis lies almost in the basal plane. More recently Burke and Hibbard3 oserved pyramidal slip at 25°C, when the stress axis was 6" to the basal plane and 14" to a <1120> slip direction. The critical resolved shear stress for pyramidal slip was 52 g per sq mm, which is only slightly greater than their value for basal slip (46 g per sq mm). Chadhuri, Chang, and Grant4 have observed non-basal slip in creep tests with polycrystalline specimens in the temperature range 250" to 350°C. The observed slip bands, which were extremely irregular in appearance, can be explained in terms of cooperative slip on {1011} and (1010) planes which have a common slip direction. Prismatic (1070) slip in polycrystalline magnesium was observed by Hauser, Landon, and Dorn.5 It was found to occur at low temperatures (78" and 195°K) and it was accompanied by cross slip in which the cooperating plane was the basal plane. Since prismatic slip occurred only at regions of high stress concentrations, the critical resolved shear stress could not be determined. Experimental Procedure The present work was performed on crystal specimens which were all cut from the same large single crystal. The original cylindrical crystal, 0.5 x 7 in., was grown in a Bridgman type furnace in which the temperature gradient was moved past the stationary crystal in the manner described by Jillson6 and Burke.&apos; High purity magnesium was furnished by the Dow Chemical Co. with the following spectro-graphic analysis in weight percent: 0.003 pct Al, <0.01 pct Ca, 0,002 pct Cu, <0.001 pct Fe, 0.008 pct Mn, <0.001 pct Ni, <0.002 pct Pb, <0.01 pct Si, <0.001 pct Sn, and <0.01 pct Zn. The large crystal was cut into four cylindrical pieces about 1.5 in. long. A flat surface parallel to the basal plane was made by hand grinding with lubricated metallographic paper on one side of each cylinder. In order to prevent bending in subsequent cutting operations, the crystals were supported by

Jan 1, 1958

By R. E. Holmes, T. W. Leland

The solution to the unsteady-state mass- and heat-transfer equations describing the adsorption of a dilute component from a gas stream flowing through a packed bed is readily applicable to the design of hydrocarbon recovery units. The solution to these equations depends on the assumption of a linear equilibrium equation to relate concentrations on the surface to concentrations in the gas. This assumption is shown to be justifiable for components which are very dilute in the gas stream. This approach permits the prediction of the effects of bed shape and size, cycle time, and gas mass velocity on the recovery of each component. It also allows the time and gas flow rate needed for regeneration to be determined. The equations involve a constant for each component and another constant characterized by the type of adsorbent. These constants must be evaluated from operating data. Values of these constants determined for silica gel are presented. This paper points out the type of experitrrental data needed for a thorough design of hydrocarbon adsorption units. INTRODUCTION The growing importance of adsorption processes to recover hydrocarbons from natural-gas streams has created an urgent need for better methods to design and predict the performance of these processes. Since the original use of solid adsorbents in natural-gas processing was for dehydration, most of the current design methods for hydrocarbon recovery re extensions of those developed earlier for dehydration. These methods are based on an adsorptivity or bed loading factor defined as the amount of a particular component adsorbed per unit weight or per unit volume of the packed bed. The recovery of a given component is then expressed as an empirical function of its adsorptivity on a given adsorbent. In spite of the simplicity and initial utility of these methods, they are not completely satisfactory in that they do not predict the effect of the dimensions of the bed in relation to flow rate and cycle time, and do not predict the distribution of various components along the length of the bed. It is possible, however, to make a considerable improvement in the design of these processes by applying the basic equations of mass and heat transfer applicable to gases containing small concentrations of adsorbing components flowing through granular beds. These equations have been developed and solved by Anzelius,&apos; Furnas,% nd Hougen and Marshall." where G = mass velocity of the inert constituents (assumed to be methane), lb/hr-sq ft, y = weight of an adsorbing component in the gas per unit weight of inert, lb of a given constituent per lb of methane, x = bed length, ft, p, = packed bed density, lb/cu ft, P, = gas density, Ib/cu ft, f = void fraction in the bed, t = time, hours, and w = weight of a given component adsorbed per unit weight of adsorbate free solid, Ib/lb pure adsorbent. The term on the left side of Eq. 1 represents the flow rate per unit bed volume of a component entering less the flow rate per unit bed volume of that component leaving the differential bed length. The terms on the right side represent, respectively, the accumulation rates per unit bed volume on the solid and in the gas phase within the differential bed section. The last term is negligible for this application since pgfv is quite small in comparison with p, and G. The partial differential is determined by the mass-transfer rate between gas and solid in the differential section.

By W. D. Robertson, A. S. Tetelman

The technique of decorating dislocations was employed to investigate deformation and fracture resulting from Precipitation of hydrogen in Fe-3 pet Si single crystals. It is shown that cracks are produced on (100) planes inside crystals, as a consequence of the precipitation of hydrogen gas, either when crystals are quenched from a hydrogen atmosphere at elevated temperatures or cathodically charged with hydrogen at room temperature. Plastic deformation in the vicinity of cracks, observed as arrays of decorated dislocations, is in conformity with the calculated stress distribution about a crack containing an internal pressure, and the observations provide information permitting a detailed analysis of the mechanics of crack growth. The fracture characteristics of crystals containing internal cracks were evaluated at 25o and -196°C and the results are related to the mechanism of hydrogen embrittlement in terms of the growth of preexisting cracks. HYDROGEN in bee iron or steel produces two characteristic changes in mechanical properties: I), a decrease in ductility (macroscopic strain at fracture) that depends on temperature and strain rate, and 2), spontaneous fracture under static load that depends on time and apparent stress. Resolution of these phenomena into the microscopic processes that combine to produce the macroscopic effects is especially difficult in the Fe-H system in which the active component cannot be directly observed and only maintained in equilibrium with great difficulty in the temperature and pressure range in which embrittlement phenomena appear. As a result of these complications, verification of the numerous hypotheses&apos;-5 that have been proposed to explain the microscopic mechanism of embrittlement depends on self-consistency with measured changes in macroscopic properties that are averaged over the volume of a specimen. It is obviously important to obtain a more direct evaluation of the microscopic processes that combine to produce embrittlement. Accordingly, the present investigation was designed to identify and observe, as directly as possible, the microscopic effects of introducting hydrogen into a bee crystal. It was concluded from a previous investigation6 of X-ray line broadening, produced by introducing hydrogen into pure iron at room temperature, that the only effect that could be associated with the introduction of hydrogen was plastic deformation; in particular, dilation of the lattice was not observed, within ± 0.01 pet, and no evidence was found that could be interpreted to support the idea7&apos;* that hydrogen occupies tetrahedral interstitial sites in the iron lattice. The absence of lattice dilation is consistent with the extremely small solubility of hydrogen in bee iron9,10 (0.015 at. pet at 900oC and 1 atm pressure), and the evidence of plastic deformation is consistent with the fact that hydrogen, introduced by cathodic charging, eliminates the carbon yield point.11-13 Following this investigation, the immediate problem was to devise a method by which plastic deformation could be observed directly. The technique employed by Hibbard and Dunn14 to observe the movement of dislocations during bending and subsequent polygonization of Fe-3 pet Si single crystals was adopted and modified for the present purpose to include the observation of dislocation arrays in the volume of the crystal, and their association with the fracture process. EXPERIMENTAL PROCEDURE Single crystals of a high purity Fe-3 pet Si alloy, containing 0.007 pet C, were grown in vacuum by

Jan 1, 1962

By Spencer S. Shannon

The lanthanide elements from lanthanum (atomic number 57) to lutetium (71) plus yttrium (39) are called the rare-earth elements; scandium (21) is chemically similar to yttrium and the lanthanides, but differs in occurrence. The rare-earth metals were divided into three categories by the chemist, Berzelius, in the early 1800s; however, modern usage defines only two groups. The cerium group is named after the most abundant -element and comprises lanthanum (57), cerium (58), praseodymium (59), neodymium (60), promethium (61), samarium (62), europium (63), and gadolinium (64). Traces of natural promethium were discovered in apatite in Finland (Erametsa, 1965). The yttrium group, also named after its most abundant representative, comprises terbium (65), dysprosium (66), holmium (67), erbium (68), thulium (69), ytterbium (70), and lutetium (71). Yttrium most closely resembles holmium in chemical properties, and occurs most commonly with the heavy lanthanides. The rare-earth minerals may be divided into cerium-group, yttrium-group, or mixed-group classes. A number of rare-earth minerals contain thorium and uranium, but these are variable in content and are not essential to the composition of the minerals. In monazite, a mineral that is a principal source of rare earths, the worldwide average content of thorium oxide is 7.2 % ; however, varieties of monazite contain as little as 0.001% and as much as 31.5% thoria. Monazite is the chief ore of thorium and, until recently, thorium has been the main product; the rare-earth metals were in fact byproducts. However, because of the great demand for rare-earth metals by the petroleum refining and the iron and steel industries since the early 1970s, the roles have been reversed so that thorium is now the byproduct. Uses A 9 to 1 mixture of yttrium and thorium oxides is used for high-intensity incandescent lamps and for high-temperature-resistant windows and lenses. Yttrium oxysulfide and orthovanadate, doped with europium oxide, are used in color television tube phosphors. Yttrium, as well as cerium, praseodymium, and samarium, is alloyed with cobalt to form strong permanent magnets. It hardens magnesium alloys and retards the oxidation of iron-chromium alloys. Yttrium-iron garnets are used for transmitting low microwave frequencies. Yttrium-aluminum garnets are used as host crystals for lasers and as artificial gems. Yttria also forms strong, stable, high-temperature refractories. Gadolinium-gallium garnets are used in substrate wafers on which bubble-memory films are deposited. Rare-earth chlorides, particularly of lanthanum, neodymium, and praseodymium, are used as catalysts for petroleum cracking. Mischmetal is used for lighter flints and to improve the ductility and impact strength of iron and steel alloys. Mischmetal also reduces the fatigue resistance of magnesium and aluminum alloys. Rare-earth oxides are used for polishing glasses and lenses. Individual or specific combinations of high-purity oxides are used as additives in glass to maintain or change its color, dispersion, or refractive index. High-purity oxide combinations are also used to color tile and to opacify porcelain enamel. Rare-earth fluorides and oxides are used in carbon-arc electrodes to provide incandescent white light. Lanthanum or gadolinium oxysulfide phosphors, activated with terbium, are used as x-ray screen intensifiers. Hydrogen can be stored by sorption on lanthanum-nickel alloys (Anon., 1979). Thorium232 is bombarded with slow neutrons in breeder reactors to create fissionable thorium233 for nuclear fuel cells. The 330-MW, high-temperature gas-cooled reactor at Fort St.

Jan 1, 1983

By R. D. Satterley

The Sherwood mine is an iron-ore mine owned and operated by the Inland Steel CO. in the Iron River district of the Menominee Range in Michigan. The property consists of an 80-acre tract in the village of Mineral Hills, about a mile north of the city of Iron River. The Ore mined is a reddish brown, nonbessemer hematite and limonite. The ore bodies lie in a large syncline having an east-west strike and are associated with a rock structure that is folded in a complex manner. The two 40-acre tracts run north and south and the shaft is at about the center of the north forty. The shaft is 1286 ft. deep, with the principal operating level at a depth of 1000 ft. from surface. A new level at a depth of 1200 ft. is in process of development. The ore body at the 1000 ft. level is east and west at approximately the line between the north and south forties and at this elevation is from 50 to 250 ft. wide and extends above the level at varying heights of from 50 to 250 feet. The 1000-ft. haulage drift extends south from the shaft, through the east-west ore body to the slates on the south side of the body. The ore body was intercepted in the drifting at about goo ft. from the shaft and was about 200 ft. wide at that point. A crosscut was extended to the east and west property lines along the south boundary of the ore body. This east-west ore body is laid out in areas go ft. wide for stoping with pillars 40 ft. wide. With this plan a stope is approximately 80 by 200 ft. and has a pillar on both sides that is approximately 40 by 200 ft. The ore has a height of from 50 to 250 ft. above the elevation of the level, therefore the height of the stopes varies in accordance with the height of the ore body at each location. From the crosscut, two main raises, each 6 by 7 ft., are put up into each 80 ft. stope area (Fig. 1). One of the main raises serves as a manway and the other as an ore raise, through which the ore is transferred from the stope to the tramming equipment. The original layout as for scraping of the ore from under the stopes into the ore raises. The ore raise is put halfway (east and west) along the 80-ft. stope area and usually is in iron formation. The manway and ore raise are on approximately 15-ft. centers. These main raises are Put up to a height of from 22 to 30 ft. above the level floor, then from the toll of the ore raise a scraper drift (8 X 8 ft.) is driven across the width of the ore body, which is in the neighborhood of 200 ft. From the scraper drift, mill raises are put up at 12½-ft. centers, staggered on opposite sides of the drift, and these are extended 23 ft. above the elevation of the scraper-drift floor. The sublevel connecting the top of these mill raises is called a mill "sub." Other sublevels are developed parallel to the scraper and mill subs at 25-ft. vertical intervals above the mill sub. The mill sub and the other subs above the mill sub are known as sublevels or dog drifts, and are 4 ft. wide and 6 ft. high. These dog drifts

Jan 1, 1946

By L. W. Sink, B. H. Kear, S. M. Copley, M. F. Hornbecker

IT is well known that under appropriate conditions of chill casting, many metals and alloys develop a columnar grain structure having a high degree of preferred orientation.&apos; In cubic materials, this principle has been employed to produce shaped castings with a unidirectional cube oriented columnar grain structure as well as shaped single crystals with a cube axis parallel to the growth ais.&apos; "he purpose of this note is to describe how this same principle can be enlployed to produce wires, rods, or more complex crystal Shapes with a variety of conlpositions in cube or random orientations by a single casting operation. The procedure for directional solidification of in Fig. 2. Examination under crossed polarizers indicated that the striations were a second phase (presumably the B19 phase) which frequently forms initially at primary grain boundaries and then grows toward the interior as thin ribbons. X-ray studies on filings of this alloy reannealed at 1300°C for 15 min indicated a strong pattern of the fcc phase together with a substantial pattern of the B19 phase. The un-annealed filings, however, showed only the pattern of a cold-worked, fcc structure. In these two-phase alloys it appears, therefore, that the B19 phase is transformed into a disordered fcc structure by cold-working. The mechanical properties of these alloys would be of some interest since a fcc structure might be expected to possess greater ductility than the or-thorhombic B19 structure from which it forms. The author wishes to thank Mr. Harvey Yakowitz and Mr. Richard Manuszewski for obtaining the photomicrograph in Fig. 2. This research was partially supported by Research Grant DE-02455 from the National Institute of Dental Research. columnar grained ingots involves pouring a melt into a preheated mold having a water-cooled copper chill at its base? and controlling the temperature gradient in the mold so as to maintain columnar grain growth from end to end of the ingot.4 This is illustrated schematically in Fig. l(a). It should be noted that the longitudinal temperature gradient promoting unidirectional columnar grain growth is maintained by heat loss primarily through the solidifying ingot to the chill, so that both the temperature gradient and the growth rate diminish with increasing distance from the chill. As the distance from the chill increases? the columnar structure coarsens, and the perfection in preferred orientation tends to increase progressively. Using this same procedure of gradient solidification, Fig. l(b) shows a simple scheme for producing a batch of crystals having the same cube orientation rather than an assemblage of columnar grains. Wires and rods are produced by cementing ceramic tubes to the wall of the mold. The steep temperature gradient produced in the central chamber is controlled by the mold heater to produce favorable conditions for crystal growth. Clearly the success of the operation lies in the selection of individual growing columnar grains by some kind of orifice at the base of each channel in the mold. Using simple constrictions, experience with nickel-base alloys has shown that 4 -in.-diam holes at a distance of -1 in. from the chill yield crystals within 7 deg of (100); closer control of orientation is possible by placing the crystal selector farther away from the chill.

Jan 1, 1970

By T. C. Poulter, B. M. Caldwell, D. E. Brink

The flash X-ray has been used more than a decade to study the configuration of the jet from a shaped charge. The high-speed, rotating-mirror smear camera has provided time-distance graphs of detonations and shock fronts in transparent materials, and the high-speed framing camera has given pictorial representations of the progress of explosive phenomena. Adequate means for measuring the paths and velocities of all parts of the shaped-charge cavity Iiner during the collapse phase have not existed heretofore. A technique enabling the single-lens framing camera to make stereoscopic photographs of the cavity liner while it is collapsing has been developed. Analysis of this photographic record gives the directions and velocities of various parts of the Iiner surface, permitting direct quantitative measurement where this has previously been impossible. Significant improvements in shnped-clrarge design are expected to result. INTRODUCTION The familiar oilwell jet perforating charge, generally referred to as a "shaped charge", is related to the Mun-roe charge first described by C. E. Munroe in 1888 and later by Neumann in 1910. It differs in construction from the Munroe charge in that its cavity is lined with some inert material (usually metal)&apos;, and it differs in performance by projecting a fast jet of dense liner material against the target instead of a stream of expanding detonation products. Fig. 1 represents a typical shaped charge in axial cross section. The charge is circularly symmetrical about its longitudinal axis. The cavity at the right is lined with metal, usually copper; and, with the exception of air, the liner is otherwise completely empty. High-explosive material is intimately in contact with the convex surface of the liner and extends in the other direction to the booster. This is a pellet of high explosive having somewhat different characteristics and serves to couple the detonator to the main charge. When the detonator is fired, a small hemispherical reaction zone of very high temperature and pressure occurs at its output end. The booster responds, adding its own latent energy to the reaction, thereby initiating the main charge. The reaction progresses throughout the main charge at a velocity of 7 to 8 mm/microsecond until all the explosive material has reacted. With a reaction pressure of about 160,000 atm, the surrounding material is moved rapidly away from the high-pressure zone. As the detonation proceeds along the cavity liner, moving from apex to edge, the liner is collapsed toward the axis of the cavity, where liner material from all parts of the concave surface converges. A zone of extraordinarily high pressure results. with only one escape path—outward along the axis. The particles from the liner, thus, become a jet of very high velocity, with a density characteristic of the material from which the liner was made. The kinetic energy of the jet, concentrated in a small area of the target, has great penetrating power. It overcomes the strength of any target, and the target material crumbles or deforms plastically to escape from the path of the jet. An unlined cavity charge, on the other hand, projects a turbulent body of hot gaseous material against a target and erodes the exposed surface. With equal quantities of explosive, the penetration effectiveness of an unlined charge is a small fraction of that of a lined charge. Given an explosive charge with a detonator at one end and an axially symmetrical metal-lined cavity at the other, one has a perforator of considerable potency. To maximize the penetrating and other desirable effects,

By R. L. Smith, I. G. Greenfield

The binary system Ga-Sb has been investigated by thermal, X-ray, and metallo-graphic methods. &apos;The intermetallic compound GaSb melts at 705.9OC and forms a eutectic with antimony at 11.8 atomic pct Ga. This eutectic melts at 589.8OC. A eutectic appears to be formed at 29.8°C but is too close to the composition of pure gallium to be detected. IN the course of an investigation of the semiconducting properties of the intermetallic compound, GaSb, the phase equilibrium between gallium and antimony has been investigated. Recently, the phase diagram of similar systems, such as In-Sb,&apos; In-AS,&apos; and Bi-As3 have been determined. These diagrams have the same general appearance in that an intermetallic compound is formed at 50 atomic pct and a eutectic is formed on both sides of the intermetallic compound. Jenny,& who has been investigating the semiconducting properties of intermetallic compounds, has concluded from thermal data of several alloys that the phase diagram of the Ga-Sb system resembles those mentioned previously. This paper represents a more detailed study of the Ga-Sb equilibrium. Experimental Procedure The gallium that was used to prepare the alloys was obtained from A. D. Mackay Inc. and the Aluminum Co. of America; the latter reported the purity as 99.95 pct. The antimony was obtained from Bradley Mining Corp. who specified a purity of 99.997 pct. Since the intermetallic compound of GaSb was prepared primarily to be used for further studies of the semiconducting properties, additional purification by a standard zone-melting technique under an atmosphere of hydrogen was performed. Hall-effect measurements on this material indicated an impurity content of less than 3 ppm.5 The antimony also was purified by zone melting and used in conjunction with the compound GaSb to make the necessary alloys for the determinations of the antimony-rich side of the phase diagram. The antimony-rich alloys were chill cast in Vycor tubes which were evacuated to a pressure of less than one micron. Since these alloys expand on freezing, precautions were taken to prevent oxidation of the ingot in the event the tube fractured. To insure homogeneity, the brittle alloys were ground and then placed in the furnace for the thermal-arrest determinations. Since the cost of gallium is high, the experimental procedure was complicated somewhat because of the necessarily limited sizes of the melts. In order to economize, the gallium-rich side of the diagram was determined by using a 35 g ingot of pure gallium initially and adding increasing amounts of antimony in order to obtain additional alloys. The furnace used in the determination of the cooling curves is illustrated in Fig. 1. A 2¼ in. quartz tube, sealed at one end, was fitted with a brass flange which was attached with DeKhotinsky cement. The brass collar was water cooled to prevent the cement from softening. An "0" ring was used to provide a seal between the brass collar and the furnace cover. Nichrome ribbon was wound around a 2 ½ in. asbestos-covered copper core which was used to reduce the thermal gradient in the furnace. The insulation consisted of alternate layers of asbestos and aluminum foil surrounded by sil-o-cel refractory and

Jan 1, 1956

By P. Shahinian, R. L. Stegman, M. R. Achter

Creep strength has been determined as a function of oxygen pressure for nickel at 510" and 600°C. Creep-rupture life drops from its highest value at the ultimate vacuum of 10-7 torr to a high pressure plateau of nearly constant life which, at 600°C, commences at torr. This behavior is described in terms of a model that relates surface gas adsorption and the generation of fresh crack surfaces. In a calculation based a this model the predicted pressure beyond which the creep strength should not decrease further has been found to agree well with the observed value. The introduction of oxygen during creep in vacuum was found to cause a prompt rise of the creep rate. The magnitude of the environmental effect was much less than generally observed in fatigue and this is attributed to the diffarent crack morphologies in creep and fatigue. GASEOUS environments are known to affect creep resistance adversely1-5 but the effects have received less attention than the much larger ones in fatigue. At low temperatures it has been shown for nickel that the creep rates are faster and the rupture lives are shorter in air than in vacuum and that these environmental effects can be correlated with faster crack growth rates in the reactive environment.&apos; In support of a mechanism of gas adsorption at the crack tip to explain the above effects, a calculation based on kinetic gas theory showed that surface coverage by gas was not as rapid as the exposure of fresh metal at the crack tip in the ultimate vacuum but was in air.7 In fatigue a number of investigations have demonstrated that the reduction of life with gas pressure usually follows a step curve with most of the reduction occurring in a transition range at intermediate pressures and little or no change at high and low pressure.8 There have been no studies, however, in which creep strength has been determined as a function of reactive gas pressure to see whether similar effects would be found. This investigation was undertaken to study the kinetics of the environmental effect in the creep of nickel. EXPERIMENTAL PROCEDURES The environmental creep apparatus was constructed to minimize many of the experimental conditions which can cause scatter in data. Dead weight loading is employed and weights are contained within the environmental chamber to eliminate bellows and the necessity for compensation for gas pressure changes. Elongation over the specimen gage length is recorded from a Riehle Model DV Controlled Environment Extensometer which provides readout to 2.5 x 10- in. Temperature is monitored and controlled from a thermocouple at- tached to the specimen gage length to +0.5oC or better. The freon trapped oil diffusion pump vacuum system included an auxiliary liquid nitrogen trap and, with a wide range variable conductance leak valve, pressures from the ultimate vacuum of 10"7 to l03 torr of any desired gas are obtainable. Pressure is measured by means of a hot filament ionization gage below 10"3 torr and a NRC Model 530 Alphatron Vacuum Gauge above 10-3 torr. The oxygen, which was leaked into the environmental chamber, was an Aviator&apos;s Grade of 99.5 pct purity with a dew point of -80°F. Analysis of the nominal 99.8 pct Ni showed the following percentages of major impurities: 0.02 C, 4.01 Mn, 0.005 Si, 0.01 Cu, 0.02 Fe, and 0.034 Mg. Cylindrical specimens were machined with a 0.180

Jan 1, 1970

By N. F. Fiore, M. C. Mangalick

DISLOCATION damping in single crystals is orientation dependent.&apos; If dislocations are distributed uniformly over all the slip systems in a crystal, and if each dislocation contributes identically to the damping process, then a damping loss or decrement 6 arises. In fact, however, for a crystal of axial direction (hkl), dislocations on certain slip systems are oriented to make a larger contribution to the damping loss than are dislocations on other slip systems. Thus the measuring damping, 6 (hkl) is proportional to an orientation factor (hkl), which weights the ability of each slip system in the crystal to contribute to the total damping. If it is assumed that dislocations are distributed uniformly on all slip systems, then for a given orientation of an fcc crystal this factor is determined2,3 by the three nonzero elastic constants Cll, C12, and C44 and the density p. In this communication measured values of elastic constants for two Fe-18Cr-Ni alloys are reported, and the dislocation damping results on two different orientations of each alloy are analyzed for orientation dependence. Elastic constants were determined by measuring the ultrasonic velocities of one longitudinal and two shear waves in (110) direction of the fcc crystals.4 Variation of velocities with the change in orientation is very small for (110) orientation,3 and so this direction is ideal for orientation factor and comparative damping measurements. Experimental Procedures. The nominal compositions of the alloys studied are given in Table I. These alloys were vacuum-melted and vacuum-cast from high-purity materials at U.S. Steel Applied Research Laboratories. The single crystals were grown by the modified Bridgeman technique. The specimens were homogenized at 1350°C for 20 hr, cut to shape and size with a spark cutter, and then annealed at 1100°C for 20 hr prior to use. In the KHz frequency range, the Marx composite piezoelectric oscillator was used to obtain the damping. The ultrasonic pulse technique was used to measure the ultrasonic velocities and the attenuation in the MHz frequency range. M.c.mANGALICK,-- StudentMemberAIME,formerly Research Assistant, University of Notre Dame, is now with Casting Laboratory, Chase Brass and Copper Co., Cleveland, Ohio. N. F. FIORE, Associate Member AIME, is Assistant Professor, Department of Metallurgical Engineering and Materials Science. University of Notre Dame, Notre Dame, Ind. This communication is part of a Ph.D. thesis presented by M. C. MANGALICK to the Graduate School of the University of Notre Dame. Manuscript submitted May 20. 1968. IMD Elastic Constants. Table I gives the values of the ultrasonic velocities. Values of C11, C12, and C44 calculated from these velocities are also given in Table I, and it is evident that there is very little variation in C11, C12, and C44 with nickel content. This slight variation may be attributed to inaccuracies in velocity measurements and practical differences in the orientations of the specimens. For example, in B the time interval for vl was 2.4 ± 0.05 sec giving an error in v1 of 0.235 x or 0.005 in. per sec. The elastic constants obtained by pulse technique were tested by calculating E<110>, Young&apos;s modulus for the (110) direction, from the equation: This value was compared with the value computed from the resonance bar measurements in which where fr is the resonance frequency and I, is the length of the specimen. In all cases, the values calculated from the ultrasonic velocity measurements

Jan 1, 1969

By F. G. Stone

A strain anneal process has been developed for the production of iron tensile test specimens, the gauge length consisting substantially of a single crystal. Since the method has been quite successful and the results of general interest, the process will be described in detail. The essential feature of the method is the continuous, slow increase of furnace temperature during the grain growth annealing treatment. Briefly, the procedure is as follows: I. Heat machined bars to 950°C in vacuum, hold I hr, furnace cool. 2. Strain to 3.5-3.8 pct elongation (axial loading). 3. Anneal, continuously raising furnace temperature from 450 to goo°C at a rate of so0 per day. 4. Hold at 900°C for 100 hr, furnace cool. Tensile test bars with a 1/4- X I-in. gauge section have been machined from 35 in. Armco iron plate and from 3/8 in. rounds of Puron, a high purity laboratory iron. The axes of the test bars were parallel to the rolling direction. During the machining operation the bars were polished in the lathe with No. 600 emery paper, and this polished surface proved satisfactory for subsequent macrographic examination. A micrographic examination of the materials showed that both were high in FeO inclusions, those of the Puron being smaller but much more numerous. An initial vacuum anneal of I hr at 950°C followed by furnace cooling resulted in a ferritic grain size of ASTM No. 3 for Armco and No. I for Puron. Special heat treatments which reversed these initial grain sizes produced no marked improvement in single crystal production after subsequent treatments. The strain for subsequent grain growth was determined by measuring the decrease in diameter of the tensile bar during elongation. The change in diameter could be measured with a micrometer to +0.0001 in., corresponding to an accuracy of 0.08 pct for the elongation. The accuracy of the diameter measurement is also dependent on grain size because of surface roughening during elongation, and for this reason, a No. 3 grain size is preferable. Optimum grain growth was obtained for strains between 3.5 and 3.8 pct elongation. Once this critical range had been cstablished, all tests were held within it, and thus only meager data were obtained on grain growth following strains outside this range. In general, grain size decreased with increasing strain to about 5.5 pct elongation. Grain growth was occasionally ohserved with less than 3.5 pct elongation although this may have been the result of error in measurement. The program control device for the grain growth anneal consisted of a I rpm motor and worm gear drive, operating the dial shaft of a pyrometer controller through a pulley. Dial speeds of 33 and 50°C per day were tried, but the results at the slower speed were not sufficiently better to warrant the increased furnace time. The furnace tube was evacuated at intervals during the run and kept sealed the remainder of the time. When the controller reached 900°C, it was stopped and the temperature held for 100 hr. This eliminated most of the numerous minute crystallites of about 0.5 mm dimension usually visible on the etched surface of the single crystal. Since recrystallization occurs at the A3 point, the top temperature of 900°C provided a 10"

Jan 1, 1949

By F. R. Brotzen, A. R. Troiano, E. L. Harmon

Precipitation processes leading to drastic property changes are a frequent occurrence in titanium alloys containing large amounts of the retained high temperature P phase. In order to establish the kinetics and nature of these precipitation processes, a series of Ti-V alloys was studied. Time-temperature-transformation diqgrams were obtained for 12.5 and 15 pct V-Ti alloys. These diagrams consisted of two intersecting C-shaped curves: one in the high temperature region for the euilibrium transformation P +u+P, and another at lower temperatures depicting the formation of the meta-stable transition phase, o. Presence of the transition phase retarded the precipitation of the equilibrium a phase. Deformation of retained P resulted in the formation of the o phase. Reversion and retrogression phenomena of the transition phase were observed. A negative temperature coefficient of resistance was found in quenched alloys containing from 15 to 20 pct V. CERTAIN titanium-base alloys can be heat treated to produce appreciable changes in properties. For example, remarkably high hardness values may be obtained by aging or isothermal quenching treatments. Most of the information available to date on the hardening of titanium-base alloys has been systematized recently in an article by L. D. Jaffe.&apos; It was pointed out by that author that the hardening was the result of the decomposition of the retained j3 phase to the equilibrium constituents, a and p, and that this decomposition had many of the characteristics of an age-hardening reaction. Recent work by Frost et al.&apos; 3 has contributed much to the fundamental understanding of the hardening mechanism in titanium-base systems. These authors established the presence of a transition phase in the transformation from j3 to a + j3, which they designated o. The transition phase, in their opinion, was at least partially responsible for the hardening and embrittling effects which accompanied low temperature aging. The present investigation of the mechanism and kinetics of the hardening reaction was carried out for the Ti-V system. Ti-V alloys were ideally suited for a study of the decomposition of j3, since age hardening was known to occur readily in this system." Moreover, no intermetallic compounds occur in this system, Fig. 1, thus simplifying the interpretation of the results. Material and Procedure Alloys containing 12.5 and 15 pct V were prepared by Battelle Memorial Institute from iodide titanium furnished by Watertown Arsenal and vanadium of 99.8 pct purity. Ingots of 8 Ib each were prepared by arc melting in an inert atmosphere with a tungsten electrode and water-cooled copper crucible. Each of the ingots was melted once, forged at 1600°, and rolled at 1400°F. Following this, the ingots were remelted, forged, and then rolled to % in. sq bars, which were subsequently grit blasted, pickled, and wire brushed. Another set of alloys containing nominally 17.5 and 20 pct V was produced by the Research Div., New York University. These alloys were arc melted in an inert atmosphere in lots of 20 g each. Heat-Treating Procedure: Whenever feasible, specimens were heat treated in high vacuum resistance furnaces at pressures below 5x10." mm of Hg. Aging and isothermal quenching treatments were generally carried out in salt baths. Specimens were not attacked by the salt, provided the tempera-

Jan 1, 1956

By W. C. Hagel, H. J. Beattie

Phases present at 2200° and 1500°F (1204° and 816°C) were identified in sixty wrought developmental austenitic alloys possessing wide compositional variations. The bases were iron-, cobalt-, and nickel-rich as well as a base with equal parts of each. There are only two structure types previously not found in similar alloys, viz .-the Co3 W and the Fe3Al types. A molybdenum-rich monocarbide decorates dislocations with unusual clarity. Other results provide correlations between alloy composition and phas e precipitation. Grouping intermetal -lic phases into three general classes : I) geometrically close-packed, 2) topologically close-packed, and 3) bcc derivatives, the nickel base prefers the first, the iron base the second, and the cobalt base the third—each base tending to shun the other two classes. Thus, a crystal-chemistry effect previously noted by Laves and Wallbaum can he expanded for these Group VIII elemental bases. There appear to he no quaternary or higher -order structure types requiring more than three atomic species. AFTER studying aging reactions in many diverse commercial austenitic alloys1-4 as a function of detailed time-temperature variations in heat treatment, it became apparent that matrix composition influenced structure types and morphologies to a large extent. These tendencies were related4 to a crystal-chemistry effect uncovered by Laves and Wallbaum.5,6 We have now directed our efforts to exploration of the whole ternary field, covering the standard base elements—iron, cobalt. and nickel— with 10 to 20 pct Cr and moderate amounts, up to 10 pct, of the usual alloy additions. Solutioning and aging treatments were held constant with major emphasis on X-ray identification of microconstituents. The possible existence of exceptions to the Laves-Wallbaum effect, or any new phases, was sought. Phases appearing in austenitic alloys can be classified as geometrically close-packed (gcp), octahedral or nonoctahedral interstitial compounds, topologically close-packed (tcp), semicarbides, and bcc derivatives. Crystal structures of the first four classifications can be visualized as a dense packing of semirigid spheres of different sizes, while the bcc derivatives represent a less efficient packing of spheres. The Laves-Wallbaum effect involves the gcp and tcp phases. Gcp phases possess both tetrahedral and large octahedral interstices; examples are Ni3Ti(n), NiSAl(y&apos;), Co3W(E), and other ordered AB3 compounds where B atoms are smaller than A. Their precipitation is primarily intragranular, presumably coherent with an austenitic matrix, and a chief source of strengthening. Most octahedral interstitial compounds (e.g., CbC, Tic, TiN, Mo2C) have a gcp lattice of large metal atoms which accommodate small carbon or nitrogen atoms in the octahedral interstices. The compound Ti2SC, previously designated Y phase or T phase, can, with some reservation due to its partial co-valency, be placed in this category.7 The nonoctahedral interstitials (e.g., M7C3, Fe3C) represent close-packings of spheres in structures that provide larger triangular-prism interstices for carbon, since the octahedral interstices formed by chromium and iron atoms are too small. Tcp phases possess only tetrahedral interstices; examples are Laves (Fe2Ti, Fe2Cb, Fe2W...AB2), p(Fe7MO6, Co7W8.... A8B7), and (FeCr, Co2Cr3)

Jan 1, 1965