Search Documents

By D. Geiselman, A. G. Guy

Single cvystals were grown from high-purity magnesium containing known amounts of nitvogen in the range 0.0008 to 0.0048 wt pet. Crystals of known ovientation were tested in tension in an Instron ma chine to determine the yield strength and to obsevue wheather a yield point occurred. Slowly cooled crystals or those given a solution heat treatment did not show a yield point. However, crystals that were aged following a solution treatment showed a yield point for all of the nitrogen contents studied. It was concluded that nitrogen caused the yield point by the Cottrell mechanism. NITROGEN has been shown to produce sharp yield points in single crystals of cadmium, zinc,2'3 ß-brass,4 and iron,5,6 as well as in polycrystalline iron7 and molybdenum.8,9 Since magnesium has a structure similar to zinc and cadmium, it seemed reasonable that magnesium should also exhibit a sharp yield point provided it contained sufficient nitrogen. Bobalek and Shrader10 reported a total nitrogen content of 0.002 to 0.0065 wt pct in com- mercial magnesium alloys, an amount well in excess of that required by theory. However. magnesium differs from cadmium and zinc in that it forms a stable nitride, Mg3N2, which has a standard free energy of formation of -95,480 cal per mole at 25" c." If rather than being in solid solution, the nitrogen were predominantly combined as the nitride, it could not act to produce a yield point. This type of behavior is the basis for the elimination of strain aging and a yield point in steel by the addition of strong nitride formers such as titanium,12 columbium,13 aluminum,14 vanadium,15 and boron.16,17 Thus, there appeared to be factors both favorable and unfavorable to the production by nitrogen of a sharp yield point in magnesium, and the purpose of this investigation was to determine the actual behavior of magnesium crystals containing known amounts of nitrogen.

Jan 1, 1960

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By Dr. O’Neil Thomas J., Donald W. Gentry

The greatest of all gifts is the power to estimate things at their true worth. LaRockefoucauld INTRODUCTION The primary reason for performing a feasibility study on a proposed mining venture is to investigate all phases of the proposal in as much detail as necessary to justify either dropping the project or continuing expenditures through the next stage. The economic evaluation component of the feasibility study, therefore, must ultimately be based on information which provides an answer to the question, "What is it going to cost?" Unfortunately engineers preparing feasibility studies never have all the engineering or economic information they would like or need. Consequently, the economic portion of the analysis can only be performed if estimates of the various costs associated with the project are made. Project cost estimates, in turn, require estimates of all the physical factors affecting cost components, including anticipated performance of plant and equipment as well as all pertinent geologic, mineralogic, and metallurgical variables. Before useful cost estimating procedures can be applied considerable data must be collected, compiled, and organized. Preparatory work typically includes organization of cost data available for estimating purposes, development of techniques for updating historical costs, and establishing methods of forecasting prices and costs over the duration of the project. Cost estimates for mining and mineral processing projects involve so many features and variables that it is absolutely essential to have some means by which the vast amount of detail can be organized. It is very important to identify, in as much detail as possible, all the cost data available (historical and developed) to the estimator. These costs, after being properly identified in detail, should be com- piled, stored, updated regularly, and made readily available for use in developing new cost estimates Accessing files of current cost information requires a standardized numerical system of classifying cost data. When uniform definitions and procedures are used, every project record contributes to the common store of estimating data.

Jan 1, 1984

AT the meeting of the Board of Directors on Jan. 28, 1927, the tentative budget of this Institute for next year was discussed, and in connection with the evident necessity for a larger income to meet increasing demands for service, the advisability of in- creasing the dues of members, was brought up. W. Spen- cer Hutchinson advocated an upward revision of the dues "believing it necessary that the Institute have a larger income, in order that it may carry on necessary work and render adequate service to its membership." Since this is a matter that directly affects every member, .President Taylor was directed to appoint a committee, which he did, consisting of George D. Barron, W. H. Bassett, and R. H. Sweetser, with T. T. Read as secre- tary, to bring in a tentative outline of the main factors in the problem for discussion at the annual meeting, on Feb. 15, and to prepare, after they have had the benefit of the discussion at that meeting, a report for the board. The amount of the annual dues is fixed by the con- stitution and can only be changed by proposing an amendment to the constitution. This amendment would have to be submitted to the members by letter ballot at the time of the election of officers for 1928, so that no change can be made in the dues for 1927 in any case. WHY THE INSTITUTE NEEDS MONEY At the annual meeting past-president Reynders, as chairman of the executive committee made the follow-ing report, which since it admirably sets forth the rea-sons why an increase in the dues has been suggested, is included here. "The report of the president has covered the situation so fully that little is left for me to say. However, a word in regard to the functions of the executive com-mittee may not be out of place.

Jan 3, 1927

By Julian Avery

IN its dual role of pig-iron smelter and gas producer, the blast furnace is a remarkably satisfactory and efficient apparatus. Many metallurgists and engineers have pointed out, however, that since the primary function of the blast furnace is to produce pig iron at the lowest possible cost, its function as a gas producer should be subordinated to this primary pur-pose. During the past 10 years or more, improvements in blast-furnace technique and economy have, in fact, been directed primarily to increasing efficiency in the use of the reducing power of the gases produced by com-bustion of coke at the tuyeres, to reduce iron ore within the furnace. The net over-all result is a decrease in the fuel value of the top gas per unit of volume, and per ton of pig iron, which is evidently more than offset in value by the corollary saving in coke and the possibility of increased furnace capacity, for otherwise there would be no point in making such improvements. The purpose of the present paper is to suggest that, while progress has been made in this direction, there is another approach to the problem of increasing the chemical and thermal efficiency of the blast furnace in its primary role as a pig-iron smelter, which appears to offer possibilities of improvement in over-all economy of a different order of magnitude than results thus far obtained by the use of other expedients. The present argument is based in large part upon the hypothesis that the effi-ciency and economics of pig-iron smelting are seriously and adversely affected by the phenomenon known as "solution loss," and that the problem of solution loss can be successfully attacked by increasing the over-all pressure; i.e., the "top pressure" under which the furnace is operated. It is indicated that pressure operation may also be expected to result in concomitant benefits, which may be summed up as generally improved operating conditions, together with a substantial saving in fuel and/or a substantial increase in furnace capacity.

Jan 1, 1938

By B. E. Mix, L. M. Barker

THe present methods of unloading ore and coarse-crushing at the Magna plant of the Utah Copper Co. are the developments of the pas five years. Hand dumping and breaking have given way to the rotary car dump and large gyratory; and the bucket elevators and stationary screens have been replaced by conveyors and shaking screens. The coarse-crushing plant may be broadly divided into two units the primary crushing and the secondary crushing, or primary roll, unit The former was erected in 1923; with the exception of the excavation the construction was carried on by forces of the company. Excavation was started in the middle of March, the first concrete was poured July 16, erection of the steel building started Oct. 30, and the unit was com pleted and operating Dec. 30. The unit has a capacity of over 24,001 tons of ore per day, and cost more than a million dollars. Remodeling of the primary-roll unit extended over a period of years preceding this some of the work having been done as early as 1918. Delivery of Ore from Mine, Yard Storage, and Handling Ori Cars to and from Primary Crushing Plant The ore is transported, in steel cars of 80 tons capacity, from the min' to the mill, where a reserve tonnage of loaded cars is maintained. Malle locomotives, handling trains of 45 cars, or approximately 3600 tons o ore per train, deliver the trains to a storage yard which contains thre tracks—a passing track and two storage tracks. All of this trackage i equipped with an overhead trolley system, so that electric locomotive can be used in yard switching. The storage tracks have a total length of 4500 ft. and provide storag space for 140 cars. The passing track, besides permitting switchin room for locomotives, is used for storage purposes between train arrivals thus giving intermittently a total storage capacity for the yard of approxi mately 200 cars. The amount of ore stored at any one time, howeve

Jan 1, 1926

By Anthony Anable

THE definite trend to stricter specifications with respect to hydraulic concrete has become increasingly manifest in the last six years or so; but it remained for the vast reclamation projects of the Bureau of Recla-mation of the Department of the Interior of the last few years to focus attention on this trend, and to demonstrate how thousands of tons of concrete-making aggregates can be produced continuously and auto-matically with a control of fineness comparable with that obtained with small samples in well equipped private and governmental laboratories. Pioneer work in this direction was done, to be sure, by private com-panies, notably the Kaiser Paving Co. of San Francisco, prior to the present vast public works program. Then in 1931 came the first great aggregates-preparation plant of the Six Companies, Inc. to supply. construction materials for Boulder Dam' in Nevada, and now, in 1936, the aggregates plant of the Mason-Walsh-Atkinson-Kier Co., general con¬tractors on the Grand Coulee dam in Washington. At Boulder dam and to an even greater degree at Grand Coulee dam, sand production is recognized as probably the most important single element affecting the physical characteristics of the concrete. For in the construction of dams accurate grading of the fine aggregate has consider-able bearing on the attainment of a uniform and homogeneous concrete of a high degree of workability and placeability and, at the same time, combining high density and low cement content. Low cement content is of value not only from the standpoint of economy but also because the use of an unnecessarily rich concrete causes certain undesirable characteristics to develop. This paper will relate how at Grand Coulee dam methods that are more advanced than ever before are producing four sizes of gravel and a sand having a fineness modulus of 2.5-3.0. The design capacity is 1000 tons an hour. Significantly, the methods and equipment employed are broadly those that have been used for a generation in metallurgical mills for accurately sizing and grading both precious

Jan 1, 1936

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By N. L. ALISON

MUCH has been published on the general subject of metal mine ventilation but, so far as I can discover, few specific data on selection of fan equipment to meet the requirements of a given mine ventilation problem are available. This article is intended to point out some of the more important considerations which influence the selection of such equipment. It will be assumed that the mine operator is able to determine the quantity of air which is necessary in the various parts of his mine to produce the required results and the pressure in inches water gage needed to circulate this quantity of air through the mine. There may be instances in which this assumption is not justified, but the fact remains that, with proper engineering talent, these data can be approximated sufficiently close for practical purposes.

Jan 1, 1930

By R. W. Bond

The gas-lift is a comparatively recent development in the Oklahoma and Kansas fields. It was used to some extent in the old Dilworth field several years ago, but the first extensive installations were made in the Tonkawa and Garber fields in Oklahoma early in the year 1926. Compressor Equipment During the early development of the system, the equipment used generally consisted of small tandem compressors of about 250 cu. ft. per min. displacement, driven by automotive-type gas engines, using a short belt drive. These compressors were first installed at the individual wells largely as an experiment. After the experimental installations had proved the method a success, it was considered economically advisable to centralize the compressor equipment in strategically located stations. However, as the information in regard to "gas-lift flowing life" was anything but definite, and the most optimistic estimates in regard to it did not exceed six months, portability of equipment was still the first consideration in the minds of many operators, who continued to install srnall semi-portable com-pressors in their centralized stations. As electric power became available in the fields, the electric motor came rapidly into use as the prime mover for the small compressors. The operating cost of this motor is greater than that of the automotive-type gas engine for the same power output, but the greater continuity of service tends to balance the extra cost. Aside from the semi-portable units, a number of strictly portable compressors were used. These consisted of automotive-type gas engines direct connected to vertical compressors. The unit was assembled on one base and could be mounted on wheels or skids as desired. The chief objection to these, in the writer's opinion, was their small capacity— approximately 150 cu, ft. per min.—which made it necessary to use two, three, and sometimes more units per well, thus making the installation rather costly. However, they have been found valuable for test purposes and emergencies, where installation time is an important factor.

Jan 1, 1928

By J. B. Umpleby

PRoduction engineering in 1927 may be characterized by a great. clarification of fundamental conceptions, and many improvements in technique. During the year the profession has received tnarked recogni-tion by the industry and to an extent never before attained has become an integral part of it. History Petroleum production engineering is a new profession. Prior to 1925, when this Institute undertook the work, no forum existed for the open discussion of its technical problems. There was no attempt at a handbook of the subject prior to "Petroleum Production Methods by J. R. Suman, in 1921, and no textbook prior to Petroleum Production Engineering" by L. C. Uren, in 1924. As late as 1926, only six schools and universities offered special courses in petroleum production engineering. Prior to about 1923, engineers engaged by oil companies were used almost exclusively for construction and location work. Two of the leading production engineers in the Mid-Continent field, although with their respective companies more than twelve years, were not definitely assigned to production work until 1924. Both men now head large departments giving almost their entire time to production problems. Because of the newness of the profession, the leading production engineers of today have had their fundamental training in mining, civil, mechanical and electrical courses. Not unlikely this diversified training is in considerable part responsible for the amazing growth of the profession. I believe, however, that recognition is due principally to economic pressure within the industry which has directed attention more and more sharply on costs and efficiency. After all, the justification for the growth and continued development, of the profession is to recover more oil from a given unit of sand at less cost per barrel. In this new profession, it seems to me that greatest progress will result from focusing thought and effort on this single objective, and if I might offer one suggestion to the com-

Jan 1, 1928

By I. R. Taylor

Union Carbide has recently developed two open- pit vanadium mines in the Wilson Srpings area of central Arkansas about five miles southeast of Hot Springs. The ores from these mines, together with those from a larger vanadium deposit at nearby Magnet Cove, are processed at a new 1600- tpd plant built by the company in the immediate vicinity (Fig. 1). The Wilson Springs vanadium deposits are associated with the Potash Sulfur Springs intrusive, a circular igneous complex which is exposed over an area that is somewhat less than a mile in diameter.1 The complex has a crude ring structure similar to that of the larger Magnet Cove instrusive six miles to the east.2

Jan 4, 1969

By Herbert Hoover

This paper is in the nature of a rough preliminary report on the progress that has been made in the application of the mass spectrometer to various problems arising in the petroleum industry. A few years ago the authors considered a number of the problems that were arising in the qualitative and quantitative measurement of small amounts of hydrocarbons. The methods available of making analyses by chemical techniques appeared to leave much room for improvement. Without going into the reasons at this point, attention was turned to the possibility of employing physical instead of chemical methods of accomplish-ing the desired results. A preliminary investigation disclosed that the mass spectrometer presented a possibility of solving many problems which could not easily be accomplished by other methods. Work was begun in developing the necessary apparatus and technique. A great deal of encouragement and many valuable suggestions were received from Dr. Robert A. Millikan, Dr. W. R. Smythe, and Dr. W. N. Lacey, of the California Institute of Technology, and from Dr. E. 0. Lawrence, who recently received the Nobel Prize, of the University of California. The authors particularly wish to acknowl-edge the very great willingness of these out-standing scientists to be helpful in solving many of the problems that were involved. So far as the authors are aware, this was the first application of the mass spectrometer to commercial work. The results were considerably better than had at first been anticipated. Briefly, it is pos-sible to run a qualitative and quantitative analysis of an unknown mixture of hydro-carbon gases, with an accuracy of better than plus or minus 5 per cent of each of the various constituents. An exceedingly high degree of sensitivity has been obtained, and a relatively short time is required to com-plete an analysis. Furthermore, it is un-necessary to separate a mixture of gases into its various components in order to complete the analysis.

Jan 1, 1940

By THOMAS G. FEAR

THE COAL DIVISION started its share of the annual meeting Monday morning with a study of coal classi fication. A. C. Fieldner was in the chair. The report of the tellers of the ballot for division chairman, stating that Thomas G. Fear had been elected to that office, was read by M. D. Cooper. Mr. Fear acknowledged the honor in a few words. In reviewing the history of the Coal Classification Committee the chairman pointed out that this was its third symposium, the last previous one having been held at the 1930 Annual Meeting. Throughout its work the com¬mittee has had the active cooperation of the Canadian workers who are interested in the subject which should result in a uniform scheme of classification in Canada and the United States. F. E. Lathe, of the National Research Council, Ottawa, abstracted the first two papers of the session entitled "Determination of the Alkali-Soluble Ulmins in Coal," by Edgar Stansfield and K. C. Gilbart, and "Moisture Determination for Coal Classification," by the same authors. The third paper "Condition of Water in Coals of Various Ranks"' was presented by its author, A. W. Gauger. Written discussions of these papers were presented by H. C. Porter and Gilbert H. Cady. In the oral discussion which followed, W. T. Thom, Jr., brought out the advisability of considering age as a factor in classification. Mr. Fieldner favored retaining bed moisture as a partial classification basis, stating that a review of many coal analyses revealed a remarkable consistency in this item in samples from a given mine particularly where the moisture content was not high. Mr. Porter pointed out that the structure and porosity of coal often have much to do with its moisture content and that these vary in different parts of a seam, particularly in anthracite. Mr. Gauger expressed doubt as to whether the Stansfield method gives the true moisture content of coal, which is needed for classification purposes.

Jan 1, 1932

By J. D. Doherty

A. R. POWELL*—Mr. Doherty has outlined in a most thorough manner valid arguments for the development of an industry in this country making syn. thetic liquid fuels from coal. No thoughtful person will dispute the statement that it is essential to carry on fundamental and applied research and acquire engineering "know-how" by the erection and operation of two or three large plants in the near future. Considerations of national security indicate that this should be done, irrespective of any temporary present surplus of natural petroleum. It is the belief of the discusser and of many others interested in coal technology that our energy picture of the future will include an increasing utilization of coal directly, without any conversion to liquid fuel, as a source of energy. A fact that is sometimes forgotten is that petroleum fuels have often been cheaper than coal in many locations and over long periods of time, and this price factor has been of great importance in expanding the use of petroleum fuels at the expense of coal. Synthetic liquid fuel made from coal must necessarily be several times as costly as the coal from which it is made, and this fact alone will have a profound effect on the future energy pattern of our country. This complete change in the economic relationship between solid and liquid fuels will lead to the substitution of coal itself for many uses now supplied by the relatively cheap petroleum fuels. From the standpoint of conservation of our natural resources, the substitution of coal itself for liquid fuels wherever possible when the age of synthetic liquid fuel arrives is also logical. At least 50 pct of the energy of coal is lost during conversion to liquid fuel. Nor is this com-pensated for by a higher utilization effi-ciency of the liquid fuel in most cases. For example, modern steam-boiler plants can operate at equal fuel efficiencies with either coal or fuel oil.

Jan 1, 1950

By C. J. Huffman

MAGNESIUM alloy tubing and hollow shapes are finding increasingly wider usage in practical applications today. Square and rectangular tubing and hollow shapes find [ ] greater diversification in use than standard round tubing. Typical applications are roller conveyors, ladder rungs, spools, furniture, tank car loading tubes, athletic equipment, and business machine parts. In general, the amount of tubing and hollow shapes produced represent a minor portion of the magnesium extrusion business. The magnesium alloys in which tubing and hollow shapes are being produced together with typical properties are presented in Table I. MI A alloy is a low cost alloy possessing good welding and stress corrosion characteristics together with moderate formability and corrosion resistance. It is widely used for low strength applications. AZ31 B, alloy is used for moderately stressed applications and possesses good corrosion resistance and formability with fair welding characteristics. AZ61 A alloy has slightly higher physical properties than AZ31 B alloy together with good formabil- [ ] ity and corrosion resistance but slightly poorer welding characteristics. AZ80 A, ZK60 A-F, and ZK60 A-T5 alloys are used where the maximum in physical properties is required. AZ80 A alloy possesses fair corrosion resistance but with formability and welding characteristics inferior to' the other alloys. ZK60 A-F and ZK60 A-T5 alloys, while only recently offered for com¬mercial use, are finding favor due, to the higher permissible extrusion rates. These alloys possess greater toughness than AZ80 A alloy and, while of moderate formability at room temperature, are very formable at 300° to 500°F. The major portion of tubing and hollow shape production at the present time is in AZ3I B alloy. Magnesium alloy tubing is commercially available in the as-extruded condition or, in the case of ZK60 A-T5, in the as-extruded and aged

Jan 1, 1951

By M. G., Corson

1. In addition to the alloys of copper with iron previously found by Hanson and Ford to show an increase in the concentration of the alpha range with increase in temperature the following binary and ternary systems have been found by the author to exhibit: the same feature: (a) Copper-chromium. (b) Copper-cobalt. (c) Copper-silicon. (d) Copper-nickel-silicon and its pseudo-binary section Cu-Ni2Si (formula of compound definitely established). (e) Copper-cobalt-silicon and its pseudo-binary section Cu-Co2Si (formula of compound established with some probability but not as definitely as for Ni2Si). (f) Copper-chromium-silicon; formation of a compound definitely established (compare Figs. 1 and 2). The formula of this compound may be either Cr2Si or Cr3Si. (g) Copper-iron-silicon; presence of a phase containing both iron and silicon established in an indirect way only. No definite microconstituents observed. 2. RANGES OF SOLID SOLUBILITY (percentage at various tempera¬tures). (a) For copper-chromium: 0.8 at 1000° C.; 0.5 at 900° C.; 0.25 at 800° C.; 0.05 to 0.1 at 500° C. (b) For copper-cobalt: 3.4 at 1000'C.; 2.4 at 900'C.; 1.7 at 800'C.; 0.9 at 600°C.; 0.35 at room temperature. (c) For copper-silicon (Fig. 3) : 6.8 ± 0.1. per cent. at 800° C.; 3 per cent. at 400° C. and probably below 2 per cent. at room temperature if sufficiently long annealed. (d) For copper-cobalt silicide: 3.3 at 1000° C.; 2.4 at 900° C.; 1.6 at 800° C.; 0.7 at 600° C.; 0.3 at 300° C. (e) For copper-nickel silicide (Fig. 4): 8.2 at 1000° C.; 5.5 at 900° C.; 3.6 at 800° C.; 1.6 at 600° C.; 0.7 at 300° C.

Jan 1, 1927

By Josiah Royce

To evaluate chemically the sample of rock obtained by diamond drilling, it has long been recognized that the analyses of the two components of the sample, core and sludge, must be given appropriate influence in computing the average analysis of any unit of depth. The purpose of this investigation is to set forth what means are available for apportioning the effect of core and sludge on the final analysis, what variables affect the problem, and what combination of applied mathematics will closest approximate the truth under each condition as these variables proceed within their limitations. A drill hole is bored in iron ore ex- ploration principally to test variations in rock composition with depth and is usually directed as nearly normal to the bedding of a horizon to be tested as possible. This practice has a tendency to minimize variation in composi- tion laterally which in any event is not likely to be great. It is obvious that the opportunity for change in analysis of a particular rock is not statistically as great radially in a diamond drill hole where the distance in which such a change may occur is from 0.719 in. (EX bit) to 1.469 in. (NX bit) as there would be longitudinally even in a run as short as 5 ft. Variations in composition of bedded or layered rocks are usually greater normal to the bedding than parallel thereto. Even in massive rocks, like porphyries, varia- tions are functions of distance. Hence, in either case, variations along the hole are of greater effect than across it.

Jan 1, 1949

By J. J. Rutledge

THE first method of working coal mines in the middle western states, more particularly in Illinois, Indiana and Missouri, was by means of the so-called single-entry method. In this method a single main passageway, or entry, was driven in the coal seam. with no parallel passageways, and from this pas-sageway or entry there were turned at intervals sim-ilar cross-passageways or entries, and from these cross-passageways, if the coal seam worked lay fairly horizontal, rooms were turned right and left. These crude methods of working were followed when the com-panies opening the mines were small and of very limited capital, and when the demand for coal was small and irregular. The principal desire was to produce coal in the short-est possible time and at the cheapest price. The chief evil resulting from such method of working was de-fective ventilation, although there were other serious drawbacks. There were then few or no good mining laws and no restrictions on those operating the coal mines. The hours of labor were long, the wages low, and the miners accordingly worked hard. All the coal was either sheared or undercut with a pick by hand. Very little solid shooting and no machine mining was done. What little air entered the mine, openings was introduced through the entries or. headings and thence conducted through the rooms by means of curtains; in many cases, as the workings became more exten-sive, the number of curtains added so materially to the mine resistance that ventilation was extremely in-efficient. Shots were fired by the miners at any time during the working shift and consequently there was more or less powder smoke or fumes in the mine work-ings all day long. Moreover, the working days were much longer than at present. The fine, dry coal-dust falling from the miners' picks while they were shear-ing or undercutting the coal filled the mine atmosphere and was taken into the lungs of the mine employees.

Jan 2, 1927

By T. Fraser, R. L. Sutherland

Under a cooperative agreement between United States Bureau of Mines and the Truax-Traer Coal Company, some operating-scale experiments have been made with the cyclone thickener in the preparation plant of the Shamrock No. 1 mine at Kayford, West Virginia. These tests were made with a 14-in. cyclone of the type developed by the Dutch State Mines in Limburg. It was applied experimentally to the thickening of solids in washery water to obtain performance data to show the range of sizes that may be recovered and other operating characteristics that would indicate the field of usefulness of this device in coal preparation practice. This is a progress report only. It covers results obtained in a series of 17 tests of the operation of what has been considered a unit of commercial size operating on suspensions of fine coal mixed with a relatively small amount of freeimpurities. The underflow material, after further dewatering in centrifuges, is a marketable grade of coal.

Jan 1, 1949