Search Documents

Jan 1, 1970

Jan 1, 1930

By John J. Strohl, Henry J. Schwellenbach

This paper relates the results obtained by decreasing the size of feed to a rod mill screen circuit. As would be expected, added production was gained and a finer grind with no tonnage loss was made possible.

Jan 12, 1950

Jan 1, 1969

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By Eugene Holman

UINQUESTIONABLY the petroleum industry not only can supply the world's present oil requirements but even can meet a considerable increase in demand if it should come. The United States produced last year 1 1/3 billion barrels of crude oil, or more than 60 per cent of the world's total. It could have provided more, if needed, because we has a large shut-in crude producing capacity. Our refining capacity of 4,500,000 0 barrels per day is more than 2 per cent above our average refinery run for 1940. Adequate crude supplies and manufacturing facilities also exist outside of the United States. Large crude reserves exist in South America, in Iran and Iraq, in Russia and Romania, in Sumatra and adjacent islands. The refineries of the Dutch West Indies, of Iran, and of the Netherland East Indies are well located in relation to crude reserves and world trade lanes. Furthermore, flexibility in the manufacturing facilities permits adjustment of yields to meet a considerable range in variations between demands for products. Only with regard to 100-octane aviation gasoline is there any apparent refinery problem. Even here so far as this country is concerned, additional refining facilities can be installed well within the time that would be required to turn out the airplane engines which will use this super fuel.

Jan 1, 1941

Rep. William S. Hill (R.- Colo.) will preside over a Congressional hearing investigating the problems of the mining industry to be conducted in Phoenix, Ariz., late in April. Rep. Hill has expressed the desire to hear from the industry itself all possible testimony on the needs of domestic mining and how Congress can help. Rep. John J. Rhodes of Arizona is also expected to attend the hearing. Two new features are incorporated into an SO2 process for treatment of low grade manganese ores disclosed by Chemical Construction Corp. The new approach includes a high temperature autoclaving step and a sintering operation. Data was given for work performed on Cuyuna Range ores.

Jan 4, 1953

By Richard H. Jahns

GRANITIC pegmatite deposits are the chief source of commercial feldspar, sheet mica, beryllium, tantalum-columbium, and lithium minerals, and certain types of kaolin. They also have yielded significant quantities of cassiterite, gems, scrap mica, molybdenite, tungsten minerals, uranium-thorium and rare-earth minerals, and zircon, either directly or as the sources of placer deposits. The output from pegmatite mines in the United States is small as compared to other mineral products in terms of bulk or value, and much of it comprises minor metals and nonmetals. Nevertheless, pegmatite minerals play a vital part in domestic industrial economy, particularly in the ceramic and electrical industries. Numerous special purpose uses also are important, even though they require small quantities of raw materials. Never was United States dependence upon pegmatite mining more clearly emphasized than during World War 11, when greatly expanded demands and uncertainties of foreign sources of supply caused much concern. Such commodities as beryl, tantalite, and sheet muscovite remained high on the critical list for months at a time, and for some minerals there was a real struggle to achieve and maintain a favorable ratio of supply to demand. Satisfactory stock piles of certain sizes and qualities of sheet mica, for example, were not built up until late in 1944, when wartime requirements already had begun to level off or even to decrease. Production of all the strategic pegmatite minerals from domestic deposits during World War I1 constituted only 10 pct or less of the total domestic consumption of these minerals, but the importance of this contribution should not be minimized. Domestic production often represented the difference between increase and further reduction of existing stocks of commodities already in seriously short supply, and in the early stages of the war it was the only assured source if imports were cut off. During the recent war period, the U. S. Geological Survey carried on a program of pegmatite studies in the New England and Southeastern States, in the Black Hills area of South Dakota, in the Rocky Mountain region of Wyoming, Colorado, and New Mexico, and in various parts of Washington, Idaho, Utah, Nevada, Arizona, and California as shown in Fig. 1. Several papers and reports already have appeared as an outgrowth of this work,'-= and others are in preparation. This paper outlines some results of data obtained by the writer during the period 1942 to 1946, when he was engaged in studies of pegmatites in the Southeastern, Southwestern, and Rocky Mountain States. Beryllium Minerals Beryl is the present commercial source of beryllium metal and beryllium compounds, which are used in ceramics, in the preparation of X-ray tubes and fluorescent lamps and screens, in special processes of paint and textile manufacture, and in the optical systems of some electrical instruments. The metal also is used in nuclear physics, chiefly as a source of neutrons. Beryllium is alloyed with aluminum for certain light-metal uses and is a constituent of some nickel and iron alloys. Currently the chief demand, however, is for copper-base alloys, which are exceptionally resistant to fatigue and wear, are responsive to hardening treatments after

Jan 1, 1952

By T. B. Massalski, Horace Pops

The occurrence and the temperature dependence of the athermal martensitic transformation in bcc Cu-Zn ß-phase alloys have been studied by cold-state microscopy, differential thermal analysis, and electrical -resistivity measurements. CinenzatograpJzic studies have shown that in the majority of alloys the transformation occurs in two stages. A thermoelastic phase, having a 'needlelike" uppearance, forms initially at the MS temperature and grows relatively slowly, chiefly in the edge (lengthwise) direction. With further cooling, an additional martensitic phase forms in rapid bursts at a lower temperature, MB, Both martensitic phases appear to have the same cry stallographic habit hut their modes of formation and growth are different. For the composition range studied, between 38.55 and 41.49 wt pct Zn, the habit planes determined are close to the (2.17 ,12) plane of the matrix, in general agreement with the prediction of the phenomenological theory of martensite formation. Thermal cycling through the MB temperature produces permanent plastic deformation in the 0 matrix and gradutally eliminates the typical burst phenomena. Thermal cycling only through the MS temperature produces no noticeable deformation effects. THE bcc Cu-Zn ß-phase alloys tend to become unstable at low temperatures and undergo a martensitic transformation,'-3 but the details of the transformation have not been completely determined. Following earlier metal log raphic and X-ray work1 Tichener and ever' determined by means of electrical-resistivity measurements the temperature range of the martensite transformation during continuous cooling. The transformation temperature was found to decrease with increasing zinc content, becoming about -130°C for an alloy containing 40.04 wt pct Zn. Hull and Garwood3 made a metallo-graphic study of Cu-Zn 0 brasses at temperatures down to -160°C, and determined the habit plane of the transformation product for an alloy containing 38.88 wt pct Zn. No metallographic studies below liquid-nitrogen temperatures have been reported. The martensitic transformation in ß-brass alloys can also be induced by deformation.1,4 The MD temperature corresponding to the appearance of the strain-induced martensite is some 300°C higher than that observed without strain, and hence the transformation can be strain-induced in alloys containing a higher percentage of zinc. Massalski and Barrett4 found that alloys containing as much as 51.89 wt pct Zn could be transformed into a faulted hcp structure by cold working at liquid-helium temperature. Because the details of the MS temperature and morphology reported in the literature are somewhat incomplete, a further study has been made of some of the above features. A design of a cryogenic stage for optical metallography5 has permitted the examination of specimens at temperatures down to 4.2oK, and the use of a cinecamera has permitted a study of the morphology on cooling and heating. The particular aim of the present work was to examine the transformation temperatures, the habit planes, and the growth morphology over a wide composition range in the ß-phase field. The effect of thermal cycling upon the subsequent transformation was also examined.

Jan 1, 1964

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By B. M. Larsen, T. E. Brower

In two previous paperslJ dealing with the carbon-oxygcn reaction, and the simultaneous content of each, in liquid steel in the furnace, we have made use of the quantity A[O], defined as the excess oxygen beyond what would be in equilibrium with carbon then present if the pressure of carbon monoxide were I atm.; that is, if [C] X [O] is taken as 0.00222, A[O] = [O] - 0.0022[C] where [O] is the percentage of oxygen by weight as measured by the method described earlier.3 This quantity ?[O] proves to be substantially independent of carbon content over the range 0.08 to I,z per cent, as well as of the basicity of the slag, and is nearly always within the limits o.o15 to o.oz5 per cent when the bath is boiling normally and is in what we have termed a steady state, Apparently it must be at least about 0.014 per cent before boiling occurs; but this threshold value seems to depend upon the ease of bubble formation at the metal-hearth interface, hence upon the condition of the surface of the hearth. In any case, ~(01, on the average, changes considerably following any disturbance of the bath, as by addition of ore. The present paper deals with the average changes in A[O] level following addition of spiegel or crop ends, or after procedures to promote stirring, or by tapping of the steel from the furnace. The observations were made on a large number of commercial heats, and consequently are subject to the influence of various disturbing factors; the results have the compensating merit of showing the consistency obtainable under the limitations imposed by practical operation. Variability of Excess Oxygen in Normal Open-hearth Operation The preceding genera' statements refer to the average value of A[0] particularly in heats that are boiling actively; on individual heats, which are less active, there may be a variable time lag between the disturbance and its effect, which complicates the interpretation of what is going on. For instance, if in the normal refining process boiling is sluggish, the slag usually is gaining Oxygen from the gas phase above it, Or from added Ore$ faster than it is losing oxygen to the metal; Yet when the bath starts to boil vigorously, the opposite condition may prevail for Some time. The consequence of this lag is a variation of A[o], the interpretation of which in a sing1e heat may not be immediately obvious. This condition is illustrated in Figs. I and 2. In Fig. 1, A[0] at the beginning of the test period was near the lower limit of its usual range (dashed lines) in the steady state as a consequence of the lime boil, which had ended about as indicated. The bath is now cold, carbon drop is slow, and the first small orc feed causes only a small rise in A[O]; as the temperature rises and as lime dissolves in the slag, and the bath becomes more active, the

Jan 1, 1948

By F. W. C. Boswell, R. L. Cunningham, H. M. Weld

Chemical analysis shows the partition of the magnesium addition between the metal and the graphite is independent of whether the graphite is in the form of nodules or flakes. The bright central spot observed in nodular graphite polished sections is shown to be due to the structure of the nodules. DURING the past few years numerous papers have been published on the production1-7 and heat treatment" of nodular cast irons. However, very little information is available on the structure of the nodules and the reason for their formation. It would appear that an explanation of the phenomenon of nodulation must await a detailed knowledge of the nature of the nodule. Disagreement exists among various workers on such a fundamental point as to whether or not a nodule actually contains a microscopically visible, nongraphitic nucleus.9-11 Work was initiated with a view to obtaining definite information on this and other aspects of the problem. Chemical Separation and Analysis Microscopic appearance had indicated9-11 that a nongraphitic core might exist in nodules (Fig. 1). It appeared that a chemical comparison of separated nodules and flake graphite would be profitable, for if the core is nongraphitic a relatively large amount of certain elements would be found in the nodules as compared to the flake. This comparison could best be made by obtaining nodules and flake from the same melt of cast iron, part of which had been in-noculated with a suitable addition reagent for the formation of nodules. A 300 lb melt was produced. About half of this was innoculated in the ladle with an Fe-Si-Mg alloy to produce nodules and cast into keel blocks; the remaining half of the melt had silicon added in an effort to compensate for the silicon in the innoculant used in the other half of the melt and this was cast into similar keel blocks. The analyses of the resultant irons are given in Table I. Nodules and flake were chemically extracted from 2 kg samples of metal as described in the appendix. While this method dissolved the iron and chromium carbides, it did not dissolve the titanium, vanadium, and molybdenum carbides. These latter carbides could have been removed by nitric acid, but in other experiments it was found that it attacked pools of metallic iron entrapped in the nodules which had, until the nitric acid treatment, been protected from the attack of the sulphuric, hydrochloric, and hydrofluoric acids. It will be shown in the next section that entrapped iron exists in nodules but not in flake. On microscopic examination many tiny irregular particles were observed to accompany both the nodules and the flake. These were identified by tabling a sample of nodules from which a sufficient fraction was obtained for X-ray analysis. A good pattern of titanium carbide was obtained indicating that this was the predominant compound present. Since it was not possible to determine how completely the carbides could be removed mechanically and since their removal from flake is much more difficult, it was decided not to resort to any separation as this would render further comparisons more difficult. The samples were ashed in a combustion

Jan 1, 1953

By J. W. Hickman

INTRODUCTION RECENT work by the authors1 on the oxide films formed on alloys of titanium and zirconium with nickel and copper indicated that an investigation of the oxides which form on alloys of copper and nickel might permit the relative rates of formation and diffusion of the ions of. these metals to be determined. This binary system is of further interest since the alloys which form are of the solid solution-type over-the entire range. In addition nickel is much more oxidation resistant than copper. A comparison of the free energies of formation of the simple oxides which may occur on these alloys indicates that nickel oxide should be observed over the entire time and temperature ranges of oxidation for all alloy compositions.1 In. order for nickel oxide to predominate on the surface, it is necessary that nickel ions form and diffuse to the surface. Two factors which may influence the formation of nickel oxide may be the ionic sizes, where Cu+ is 0.96Å and Ni-++ is 0.70Å, and the charges on the ions. On the basis of size, Ni++ should diffuse more readily than Cu+ while on the basis of charge, Cu+ should form more readily than Ni++. According to Uhlig2 passivity to corrosion in an alloy appears at a critical composition which for copper-nickel alloys is related to the tendency of the d band of electronic energy states to fill with electrons. This composition in the copper-nickel alloys corresponds to 40 at. Pct nickel at which composition Uhlig2 (quoting La Que's data) states that the alloy system becomes passive. Magnetic and specific heat data indicate that the d band of copper-nickel alloys is filled at 6o at. pct copper or 4o at. pct nickel. Mott and Jones3 have shown that if, on alloying nickel with copper, one considers a copper atom to be identical with a nickel atom except for an extra electron (nickel -has the-configuration: 3d8 4s2 and copper: 3 d10 4s) then at 60 at. pct copper or 4o at. pct nickel enough electrons are contributed by copper to fill the d band of the alloy. At this composition the magnetic susceptibility approximates zero according to Grew.4 Although the electron diffraction data will not determine the rates of the several reactions which may occur during oxidation, yet a determination of the structures of the surface oxides may yield information concerning the relationships, if any, which may' exist between the oxide structures which form and that composition where the magnetic susceptibility approximates zero. It is quite possible, of course, that the mechanisms of the oxidation and corrosion reactions may be so widely different that no correlations between them may be possible. SURVEY OF LITERATURE The metals, copper and nickel, which are face-centered cubic, form solid solution alloys which are face-centered cubic with no superstructure for all compositions. Three oxides of nickel have been investigated structurally by X ray diffraction. Of

Jan 1, 1948

By Charles A. Stetefeldt

This treatise is the sequel of a paper on "Russell's Improved Process for the Lixiviation of Silver-ores," etc., read at the Chicago meeting, in May, 1884, and published in the Transactions, vol. xiii., page 47. The facts it presents are principally compiled from Mr. Russell's notes on his practical experience gained in various places where the Russell process has been introduced. For a complete understanding of this paper a perusal of my former one is desirable, as can be seen from the frequent references here made to it. All silver-ores that do not carry a large percentage of lead or copper can be treated by Russell's process with success and economy. I do not mean to create the impression that from ores containing considerable quantities of lead and copper a high percentage of the silver cannot be extracted by this process. Such ores, however, will, in many localities, be reduced to better advantage by smelting. In case lead-bearing silver-ores are suitable for concentration, it may be profitable to concentrate the ore by Krom's dry system, obtaining a smelting-product high in lead, and to lixiviate the tailings and the dust. This plan has been adopted in a mill recently erected in Cortez District, Nevada. The dry system of concentration deserves the preference because it delivers the tailings and the dust in a condition ready for chloridizing-roasting. In wet concentration the drying of the tail ings would be expensive, and there would be a considerable loss of silver in slimes. Oxidized ores, containing silver chloride and lead minerals, may be lixiviated after crushing, and the tailings may be concentrated for lead. In this case wet concentration would be most suitable. This has been done at the Old Telegraph Mine, Utah. I would give, however, the preference to dry concentration in all cases which, of course, requires that concentration should precede lixiviation. The Russell process is also adapted to the treatment of tailings resulting from ores which have been worked either by the old

Jan 1, 1887

By V. F. Parry, E. O. Wagner

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrapment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pet, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented. THIS paper presents a summary of investigations by the Coal Branch of the Bureau of Mines during 1949 on the removal of internal moisture from low-rank coals by processing them in the entrained and fluidized state. A paper on this subject, giving a summary of the early work, was presented at the 1949 AIME annual meeting1 and gave a the- oretical discussion of the time and heat required to dry various sizes of low-rank coal. The investigations on two pilot plants were presented in the foregoing paper. During 1949, three additional pilot plants were built to study phases of the drying problem and to investigate different techniques of handling fine coal in the entrained and fluidized state. The present paper gives operating data on the new units and presents detailed data on the drying of seven coals having bed moisture ranging from 62 to 24 pct. The problem of removing surface moisture from fine coal is principally one of heat exchange and dispersion of the coal particles so that heat can reach the liquid moisture to permit evaporation, and it does not involve the factors of size and time of contact to any great extent. If enough heat can reach the surface of the particles at temperatures higher than 250°F, moisture evaporates almost instantly, and the factors of time and size are of secondary importance compared with the factors of heat balance and dispersion of the coal. Therefore, it does not appear to be necessary to employ a fluidized bed when removing surface moisture, and the most efficient process would be one in which the coal particles are entrained in a hot gas stream of optimum temperature traveling at a velocity that causes the particles to disperse into a low-density phase. When low-rank coals are dried, the fluidized bed is necessary to provide control of time of contact. This is done by adjusting the superficial velocity which controls the density or dispersion of the particles. The density of beds having fluidized properties suitable for drying low-rank coals appears to range from about 5 up to about 15 lb per cu ft. When the density is below 5 lb per cu ft, which represents a low-density phase, optimum conditions for removal of surface moisture should be found, and this requires superficial velocities of about 15 fps. The problem of removing bed moisture from low-rank coals involves consideration of size of coal, temperature, mass flow, heat balance, pressure, time of contact, and method of dispersing the coal in the heating mediums. The experimental work presented here gives data on these factors. Coal sizes up to 1/2 in. x 0 were dried with hot gases having initial temperatures ranging from 1900° to 2400°F. Coal

Jan 1, 1951

By E. O. Wagner, V. F. Parry

This paper summarizes investigations during 1949 on three pilot plants for drying low-rank fine coal by entrapment in hot gases. Detailed operating results on processing seven coals having moisture ranging from 24 to 62 pet, formulas and data for calculating performance of large units, and general conclusions on the problem of drying fine coal are presented. THIS paper presents a summary of investigations by the Coal Branch of the Bureau of Mines during 1949 on the removal of internal moisture from low-rank coals by processing them in the entrained and fluidized state. A paper on this subject, giving a summary of the early work, was presented at the 1949 AIME annual meeting1 and gave a the- oretical discussion of the time and heat required to dry various sizes of low-rank coal. The investigations on two pilot plants were presented in the foregoing paper. During 1949, three additional pilot plants were built to study phases of the drying problem and to investigate different techniques of handling fine coal in the entrained and fluidized state. The present paper gives operating data on the new units and presents detailed data on the drying of seven coals having bed moisture ranging from 62 to 24 pct. The problem of removing surface moisture from fine coal is principally one of heat exchange and dispersion of the coal particles so that heat can reach the liquid moisture to permit evaporation, and it does not involve the factors of size and time of contact to any great extent. If enough heat can reach the surface of the particles at temperatures higher than 250°F, moisture evaporates almost instantly, and the factors of time and size are of secondary importance compared with the factors of heat balance and dispersion of the coal. Therefore, it does not appear to be necessary to employ a fluidized bed when removing surface moisture, and the most efficient process would be one in which the coal particles are entrained in a hot gas stream of optimum temperature traveling at a velocity that causes the particles to disperse into a low-density phase. When low-rank coals are dried, the fluidized bed is necessary to provide control of time of contact. This is done by adjusting the superficial velocity which controls the density or dispersion of the particles. The density of beds having fluidized properties suitable for drying low-rank coals appears to range from about 5 up to about 15 lb per cu ft. When the density is below 5 lb per cu ft, which represents a low-density phase, optimum conditions for removal of surface moisture should be found, and this requires superficial velocities of about 15 fps. The problem of removing bed moisture from low-rank coals involves consideration of size of coal, temperature, mass flow, heat balance, pressure, time of contact, and method of dispersing the coal in the heating mediums. The experimental work presented here gives data on these factors. Coal sizes up to 1/2 in. x 0 were dried with hot gases having initial temperatures ranging from 1900° to 2400°F. Coal

Jan 1, 1951

New York Meets first Wednesday after first Tuesday of each month. DAVID H.-BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. . ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 11, 1915