Search Documents

By J. J. Lander, L. H. Germer

MOLYBDENUM and tungsten have desirable corrosion and temperature resistant properties, but the metals in bulk are expensive and their fabrication is difficult. Such considerations led to a search for a method of plating them upon base metals. This search was successful and led furthermore to a number of developments which could not have been foreseen. Neither pure tungsten nor pure molybdenum has been electroplated successfully, although the literature of electroplating is liberally sprinkled with the description of unsuccessful attempts. The process of plating these metals by thermal reduction of their halides has achieved only limited usefulness because of technical limitations and because of limited range of product quality. Plating by thermal decomposition of the carbonyls does not suffer from limitations of the same sort and the properties of the plate are readily controllable. This paper describes the plating of molybdenum and tungsten, and of compounds and alloys of these metals, by pyrolysis of their carbonyl vapors. Chromium also has been plated in this manner, but the experiments upon chromium have been less extensive and the results much less satisfactory. Probably the most important of the products which we have obtained are the alloys with carbon, and the carbides of the metals. Either molybdenum or tungsten can be deposited upon a base metal as a coherent and adherent coating. By adjusting the plating condition the carbon content of the coating can be made to have any value from substantially zero to about 35 atomic pct. The hardness is dependent primarily upon the amount of carbon in the plate and can be regulated over a very wide range, some coatings containing considerable carbon being harder than sapphire. In addition to products already known this method of plating has yielded new carbides of molybdenum and tungsten and alloys supersaturated with carbon. These new products are possible because, in the process of plating, carbonyl can be decomposed at temperatures as low as about 150'C, and thus in the presence of other substances reactions occur which could perhaps not be produced in any other way. In addition to carbides and alloys with carbon, sulphides and oxides of molybdenum and tungsten have been produced and studied. There are certain other advantages of the carbonyl method of plating. It is not required that the base have good electrical conductivity as in electrochemical processes, and the base need not have the temperature stability required in plating from a halide. Thus low melting glasses, as well as other ceramics, can be plated almost as readily as metals. In particular, the plating of glass with

Jan 1, 1947

By Charles R. Wraith

The property of the Roan Antelope Copper Mines, Ltd., is situated at Luanshya, north central part of Northern Rhodesia, and is connected with the main line of the Rhodesia Railways, Ltd., by a 24-mile branch line from N'dola. Most of the material and supplies that are not available in Africa are shipped into the country via Beira, on the East Coast of Africa, a distance of 1473 miles from Luanshya and the nearest ocean port. The output of copper is shipped by rail to Beira and thence by boat to the market. Passenger travel is mostly via Cape Town, a distance of 2162 miles from Luanshya. Excellent passenger trains operate on regular schedules between Cape Town and Northern Rhodesia. Luanshya is 13" south of the equator at an elevation of 4000 ft. above sea level, and has a mild healthful climate. During the rainy season, from October to March, the rainfall averages 53 in. The area is profusely covered with vegetation. An ample supply of water for industrial and domestic purposes is available throughout the year. The more important supplies for smelting purposcs, such as wood, coal, limestone, silica, quartzite, and clay for "dolly" mud, are conveniently available. Excellent grades of coal, coke and firebrick are obtained from the Wankie Colliery Co., Ltd., Southern Rhodesia. The Wankie colliery has just completed the erection of equipment for the manufacture of silica brick. An ample supply of quartzite of good grade is available for this purpose. Silica brick is also obtained from the Belgian Congo and from India. Limestone is quarried from a large deposit a few miles from Bwana Mkubwa, which is 30 miles by rail from the smelter. An abundant supply of clay for " dolly " mud and for lining launders is available within a short distance of the smelter. Metallurgy Copper is contained in the ore as chalcocite, chalcopyrite and bornite. Chalcocite predominates in the eastern end of the orebody almost to the exclusion of other copper minerals. The amount of chalcocite decreases with a corresponding increase of chalcopyrite and bornite toward the western extension, where the latter predominate.

Jan 1, 1934

By E. O. Jones

DURING the heating of cold-worked nickel silver, the tendency of the material to crack is well known. The present research deals with this question, and may conveniently be divided into the following sections: Changes in these alloys during heating and cooling, determination of the temperature at which cracking occurs, effect of grain size, quenching cracks, methods of overcoming annealing cracking. The work is far from complete, in particular the influence of impurities on this tendency has not been investigated, but the results so far obtained lead to certain definite conclusions, which are of theoretical and practical importance. CHANGES IN ALLOYS DURING HEATING AND COOLING During the annealing of many metals at a temperature just below that at which recrystallization sets in, there is evidence of some change, the effect of which is to harden and embrittle the material. This effect has been most clearly demonstrated in the cases of aluminum, copper, brass, and nickel silver, and appears to be a common property of cold-worked metals and alloys, or, at any rate, the non-ferrous ones. The effect would obviously offer an explanation for certain types of annealing cracking, but the trouble is so much more common in the nickel silvers than in the other alloys that some special cause should be looked for. There is, however, fairly good reason for believing that similar cracking may occur in some of the brasses; D. Bunting suggests that the a brasses toward the saturation limit are subject to a transformation closely allied in nature to that known to occur in the nickel silvers at around 320° C. Although the existence of this critical temperature range was known, it did not necessarily follow that this transformation was responsible for the trouble under investigation, so the first portion of this paper deals with the attempts made to determine whether other critical changes might not occur in these alloys. There were already reasons for the belief that such would prove to be the case, as the mechanical properties of the nickel

Jan 7, 1925

By F. H. Parsons

At the time that converting or bessemerizing of copper matte first began to be practiced by the smelters in the copper industry, converters were lined by tamping the flux, usually siliceous ore, into the steel shell. About 1910, practice in several plants had demonstrated the superiority of a basic lining of nonfluxing material and the addition of flux through the mouth of the converter. Adoption of the new method by nearly the entire industry followed. Basic linings are made of refractory "magnesite" brick manufactured, usually, from imported dead-burned magnesite. Either the linings are laid up in the shell dry or the bricks arc bonded with some mortar dictated by the preference of the user. Foreign, usually Austrian, magnesite was the main source of supply for these bricks, although there were domestic sources, but it was not until costs began to rise a few years after the first use of basic linings that these domestic sources were investigated to any great extent. Exigencies created by the World War necessitated the use of the domestic magnesite during this period, but the brick manufacturers reverted to the use of the foreign product after the war, because the impurities therein made a brick with a better fire bond than the purer domestic magnesite. Therefore the domestic product became available at a favorable price for any metallurgical process that permitted its use. The United Verde converting practice using magnesite linings has resulted in a high consumption of magnesite because of the zinc content of the low-grade matte. It was realized that the cost of these linings represented a large portion of the cost of converting, and an investigation was started to find means by which these costs might be lowered. In the neighboring state of California rather pure magnesite was being mined and treated for the market. The product, however, was purposely made to simulate the dead-burned grain magnesite product from foreign sources by the addition of fluxing impurities before burning. It was learned that this dead-burned California grain magnesite could be laid down in Arizona at a price one-third that of the same tonnage of "magnesite" brick manufactured from foreign magnesite. It was also learned that at least one California producer was ready to supply the market with periclase, which was a grain magnesia produced by burning the

Jan 1, 1934

By Ralph W. M. Lai, D. W. Fuerstenau

This paper presents the results of a study of the principles which control the distribution of ultrafine particles between an oil phase and an aqueous phase. Alkyl sulfonates were used to control the wettability of fine alumina particles and to stabilize the water-isooctane emulsion system in the extraction process. The effects of sulfonate chain length, sulfonate adsorption, pH, and oil-water ratio on the recovery of solids in the oil phase were investigated. Higher extraction was found under conditions which yield higher hydrophobicity and large interfacial area of the oil-water emulsion. Today there is considerable interest in developing methods for the recovery of fine particles from disseminated ores. One such method might be the extraction of fine particulate solids from aqueous suspensions into an oil phase, and one example of a successful industrial process based on oil-water distribution phenomena is the emulsion flotation process used in concentrating manganese ore.' The oil agglomeration process of Farnand, Smith, and Puddington has been suggested for concentrating tin ore. Patents 3-4 for oil flotation processes extend back to that of William Haynes in 1860. The basis of all these processes is directly related to the stabilization of emulsions with solid particles. The first extensive study of oil-water emulsions stabilized by finely divided solids was made by Pickering. Later, Briggs,6 weston, 7 Chessman and King,8 and Leja and Schulman9 experimentally demonstrated how solid particles control water-oil and oil-water systems. Hildebrand10 suggested that fine particles can stabilize an emulsion because the fine particles are partially wettable by both oil and water, that is, that the contact angle must be finite. Takakuwa and Takamori 11 recently applied emulsion inversion to the study of collector adsorption in flotation systems. At the Royal School of Mines, Shergold and Mellgren12 are currently carrying out a comprehensive study of the extraction of fine particles into an organic liquid phase. In the present study of the liquid extraction or oil flotation of ultrafine particles, the recovery of hydro-philic alumina particles of 0.1-µ average diameter was determined after separating an isooctane-water mixture (emulsion) into its two phases. Alkyl sulfonates of different chain lengths were used to change the wettability of the alumina and to effect emulsifi-cation of the oil-water mixture. The effects of the oil-water volume ratio, sulfonate adsorption, and pH on the recovery of the fine particles were investigated. Since the surface charge on an oxide such as alumina is determined by the adsorption or interaction of H+ and OH- with the surface, pH control is extremely important. Furthermore, since the zero point of charge (zpc) of alumina13-14 occurs at pH 9 to 9.4, major adsorption effects with anionic collectors in these systems will occur below pH 9. The results of the foregoing investigation are discussed in terms of the recovery of the fine particles, the oil-water ratio, contact angles, surface tension, the adsorption of sulfonate onto the solid surface, and the emulsifica-tion of oil. MATERIALS AND EXPERIMENTAL METHODS Materials: The particulate solid used in all the experiments was Linde "A" alumina, a high-purity, readily available form of a-alumina. The surface area of the alumina, as evaluated from measurements of stearic acid adsorption from benzene, was 14.5 sq m per gm, based on a value of 20.5 sq Å for the cross-sectional area of stearic acid.13 All aqueous solutions were prepared from triply distilled conductivity water. Other materials included high-purity crystals of sodium alkyl sulfonates, isooctane, and, for pH adjustments, reagent grade hydrochloric acid and sodium hydroxide-Because sulfonic acids are strong acids, they are

Jan 1, 1969

By Y. Nakada, B. Chalmers

The work-hardening behavior of surface layers of aluminum and gold single crystals was investigated by alternately deforming and then removing a thin surface layer by electropolishing or by etching. Aluminum crystals exhibited lower flow stresses after the surface removal; gold crystals did not. Abrasion of surface eliminated easy glide in both gold and aluminum crystals. By alternately deforming and removing the surface layer, it was shown that the abraded crystals work-harden preferentially under the abraded layer. It is suggested that this phenomenon is caused by the difficulty of propagating dislocations through the abraded layer. It has been demonstrated in numerous cases'-3 that the plastic behavior of metals in either single-crystal or polycrystal form is sensitive to the environment and to the condition of the surface; it has also been reported4-6 that single crystals of some metals, when deformed in tension, exhibit more work hardening near the surface than in the interior. A third type of effect that has been attributed to the special part played by the surface in plastic deformation is the influence of the dimensions of the specimen on the various parameters that define its plastic-deformation characteris- tics.?-'' Many of these experiments were made on aluminum, on which an oxide film is always present under available experimental conditions; many of the effects have been attributed to the oxide film, either in terms of its higher elastic moduli, which would cause local stress redistribution, or its higher strength, which would oppose the escape of dislocations at the surface of the metal. On the other hand, it has been suggested II,12 that the mere presence of a surface should be sufficient to produce the observed results. A rigorous examination of this question could, in principle, be carried out by comparing the behavior of aluminum with its oxide film with that of the same material without oxide. This experiment would present great difficulties. The most practical alternative is to compare aluminum with gold, which has no crystalline surface film at room temperature, and to study the effects of various surface treatments on gold. The experiments described in this paper fall into two groups, the objectives of which were to determine 1) whether single crystals of gold shared the property of aluminum that the removal of a surface layer after some plastic deformation reduced the flow stress for further deformation and, since the result of this was negative, 2) whether a surface treatment could be found that caused gold to behave in this way. I) EXPERIMENTS AND RESULTS All the tests described below were carried out on single crystals of about 6 by 6 mm cross section and of sufficient length to provide a gage length of about 10 cm.

Jan 1, 1964

By G. G. Hancock, H. H. Johnson

Hydrogen gas at atmospheric pressure is shown to cause substantial embrittlement in a martettsitic high-stretzgth steel. Subcritical crack growth is observed at very lom stresses and with high growth rates. It is suggested that an adsorbed layer of hydrogen atoms at the crack-tip surface provides the damaging hydrogen. Oxygen in small quantity, as little as O.7 pct by volume, is shown to eliminate subcritical crack growth in gas environments caused by hydrogen or water vapor. However, dissolved oxygen in water has little or no influence upon crack-growth rates. Oxygen-stopped cracks may be restarted by water, or by hydvogen or water vapor if oxygen is removed from the environment. These observations are interpreted in terms of preferential adsorption of oxygen at the crack tip and the formation of an oxide barrier. RECENT investigations1-3 have demonstrated that environmental factors are frequently responsible for delayed failure in martensitic high-strength steels. The environment causes crack initiation from preexisting cracklike flaws at unexpectedly low stresses, often far below the uniaxial yield strength. The crack then propagates at a rate controlled by the environment and the crack-tip stress-field intensity; during this period crack propagation will cease if either the stress or the aggressive environment is removed, and this may be considered a definition of subcritical crack growth. Fracture occurs when the crack has grown to a critical length, such that the fracture toughness of the steel is exceeded. Several liquids are known to cause delayed failure, but water and water vapor are the most severely damaging of the environments investigated to date.'-3 It has been suggested that hydrogen produced during corrosion reactions may be the actual embrittling agent2 The severe embrittlement caused by water vapor inevitably raises the question as to whether other gas environments are damaging. Previous work4'5 has demonstrated that high-pressure hydrogen (2250 psi or greater) is an effective embrittling medium, as measured by such criteria as reduction in area, notch tensile strength, and time to failure. Moreover, the embrittlement was eliminated by the addition of small quantities of air or oxygen to the high-pressure hydrogen, but it was not influenced by additions of nitrogen or argon.4 In the present study attention is focused upon gas environments at atmospheric pressure, in particular hydrogen and oxygen. The influence of these constituents upon the initiation and growth of a crack from a pre-existing cracklike flaw in a high-strength steel was determined directly by the electric-potential method of monitoring crack growth. MATERIALS AND PROCEDURE The H-11 steel was supplied by the U.S. Naval Research Laboratory as 3 by 12 by 0.065 in. sheet specimens with 1-in. transverse center slots. The slot tips were finished by Elox machining to a radius of 0.001 in. or less. The yield strength was 230,000 psi; chemical composition and heat-treatment schedule are given in Table I. The experimental apparatus, precracking procedure, and incremental loading sequence have been described previously.3 In the only significant change, precracking was sometimes carried out by a hydrogen embrittlement and baking technique. All experiments were conducted at room temperature; the hydrogen gas environment was purified by a commercial palladium purifier. Crack initiation and propagation were followed by the electric-potential method,'-3 using a calibration that has been recently dicussed. Stress-field intensities at the crack tip were computed by the conventional Irwin frmula; the plasticity correction was negligible and therefore not included. EXPERIMENTAL RESULTS A striking brittleness associated with molecular hydrogen at atmospheric pressure is demonstrated by the data in Table I1 and Fig. 1, which indicate that subcritical cracks in hydrogen initiate at lower stress-field intensities and propagate more rapidly than in fully humid argon. Ki and Kf are the crack-tip stress-field intensities at initiation and termination of subcritical crack growth, respectively. Termination, of course, corresponds to fracture. In both hydrogen and humid argon Ki is less than Kf

Jan 1, 1967

By P. LaRochelle, K. Y. Lo, A. L. Tamuly Phukan

In many civil or mining engineering works, the stresses and deformations of natural or excavated slopes due to the combined effect of self-weight and initial stresses are of interest. Because of the mathematical complexities of this problem, however, no complete exact solution exists for the simplest case, that of assuming the stress-strain relation of the rock to be perfectly elastic. Efforts have therefore been directed toward numerical and experimental technique. The stresses within an elastic slope have been obtained by LaRochelle,1 using the photoelastic and finite difference method to determine the difference and sum of principal stresses. Subsequently, Finn,2 Hoyaux and Ladanyi,3 and Duncan and Dunlop4 attempted to solve the same problem by using the finite element method. The problem was also investigated by Brown and Goodman5 and Brown and King6 who emphasize the importance of the effect of loading or unloading procedure on the stress distribution within the slope. Although the geometry of the slope and the boundary conditions involved are identical or similar, the results obtained by these various authors by no means agree. It is therefore necessary to review briefly the results of elastic analysis in order to lend credence to the methods used in the solution. Although the stress-strain behavior of some rocks may be reasonably approximated by the elastic modrl, other rocks generally exhibit an elasto-plastic behavior with strain hardening or strain softening as shown in Fig. 1. Experiments show that for most rocks, the stress-strain relationship is approximately linear from the origin to the point P (neglecting the small concave region under low stresses). At P, the curve deviates

Jan 1, 1970

By D. Turnbull, R. E. Cech

FISHER, Hollomon, and Turnbull have developed a theory for the nucleation of martensite. They first tested the theory on Fe-C alloys and low alloy steels. The major factor influencing nucleation of martensite was considered to be statistical composition fluctuations occurring in small regions at high temperature and frozen-in on quenching. These local regions of varying size and composition serve as nucleation centers. They become supercritical, one by one, as temperature is progressively lowered, resulting in temperature-dependent or athermal transformation. Fisher next applied nucleation theory to substi-tutional solid solution alloys. Detailed predictions were made for Fe-Ni alloys because of the availability of free energy data on this system. It was shown that composition fluctuations that were significant energy-wise did not occur, and nucleation frequencies could be calculated from average properties of the system. Nucleation was predicted to occur as time-dependent and having the functional relationship to give a C curve of nucleation frequency vs temperature. The analysis further predicted that the nucleation frequency was extremely sensitive to composition. Experimentally, it would be found that the transformation in some compositions is so slow that measurable amounts will not form in a reasonable length of time. With other compositions, only slightly different, the nucleation frequency becomes so great that the material becomes transformed while still distant in temperature from the maximum nucleation frequency. On quenching an alloy of such composition, the observed transformation kinetics would be similar to those found in Fe-C alloys. Cech and Hollomon repeated experiments of Kurdjumov n which the kinetics of transformation were similar to those predicted by Fisher for Fe-Ni alloys. The alloy studied in this investigation contained 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn. Fisher,' using an idealized model for the extent of transformation as a function of the number of martensite crystals per grain of parent phase, derived nucleation frequencies from the transformation curves of Cech and Hollomon. Complicating influences such as coupling effects between grains in the polycrystalline specimens were neglected. Nevertheless, excellent agreement was found between the theoretically and experimentally derived nucleation frequencies. These experiments, however, could not provide a critical test of the theory. Experimental nucleation frequencies could vary widely from those calculated, depending upon the extent of deviation from ideal partitioning and the extent of coupling effects. Further, since the compositions of material theoretically analyzed and experimentally determined were different, the free energy changes involved in the experimental work could only be estimated. Also, the effect of heterogeneities on the transformation kinetics was not considered. For these reasons, it was decided that experiments designed to test the validity of the Fisher analysis must be conducted on binary Fe-Ni alloys, which were the ones considered theoretically by Fisher. The martensite transformation in Fe-Ni alloys has been the subject of considerable study. Machlin and Cohen have shown that transformation proceeds in a manner quite unlike that in any other ferrous alloy system. They found that single crystals would transform to a large extent in a single burst. In large grain polycrystalline specimens, frequently more than one grain and sometimes the whole specimen would transform at the same instant in this manner. Results on filings indicated that different particles would undergo the burst transformation at widely different temperatures. These results support the conclusion that the transformation behavior could not be described by a single nucleation frequency as would be the case if the nucleation were homogeneous. It appeared that further work was necessary to define the factors responsible for burst-type transformation, so that the conditions could be altered to favor homogeneous nucleation of martensite if such could be accomplished. This report summarizes the results of some experiments conducted with powdered Fe-Ni alloys for this purpose and the re-

Jan 1, 1957

By Charles R. Keyes

PAGE. I. IntRoduction,...........139 11. Four Phases of Primary Ore-Genesis,......141 1. Extraction of Ore-Materials from Sea-Water,....141 A. Early Views,........141 B. Metals in Sea-Water,.......142 C. Metallic Content of Sedimentary Rocks,... 142 D. Adequacy of Metal-Percentage to Form Ore-Deposits, . 143 E. Derivation of Metallic Elements in Sea-Water,.. 144 2. Metallic Content of Igneous Rocks,...... 145 A. Two-Fold Meaning of Term,.....145 B. Significance of Ordinary Rock-Analyses,... 146 C. Wide-Spread Occurrence of Rare Rock-Forming Minerals,.........146 D. Occurrence of Metalliferous Minerals in Rocks,.. 146 E. Metallic Content of Igneous Rocks Generally,.. 147 F. Metals in Volcanic Rocks,......148 G. Originality of Metal-Content of Rocks,...148 H. Physical Condition of Metallic Minerals,... 149 3. Magmatic Origin of Metals,.....,.149 A. Association of Ores with Cooled Magmas,... 149 B. Deep-Seated Origin of Metals,.....150 C. Magmatic Waters in Ore-Deposition,.... 150 D. Ore-Materials of Volcanic Emanations,... 151 E. Exportation of Metals from Magmas,.... 152 F. Ores of Magmatic Differentiation,.... 152 4. Meteoritic Derivation of the Metals,.....- 153 A. Planetesimal Hypothesis,...... 153 B. Number of Meteorites,.......154 C. Abundance of Meteorites in Desert-Regions,.. 156 D. Petrologic Character of Meteoric Falls,... 159 B. Metals in Meteorites,.......159 F. Incorporation of Meteoritic Materials in Ores, , .160 811. RecapitulatioN,..........161 I. Introduction. If the long controversy waged between those who, on the one hand, advocated a strictly deep-seated origin of ore-deposits, and, on the other hand, those who argued for an ore-genesis by

Jan 1, 1911

By Foster Bain

MOST of us householders in the East burn anthra-cite, so the problem that interests us most is the distribution and supply of the domestic sizes of anthracite. That, however, is only a small part of the coal problem and has its own peculiarities. Whether anthracite prices are high or low is largely a matter of relativity, depending on the size of the transaction, the available supply, and other things. As an isolated example which I hesitate to quote because it is not entirely representative, you may be interested to know that the Government fuel yard has been delivering to the Government buildings in the District of Columbia, white-ash stove coal at 16 c. a ton less during January, 1923, than during the same month of 1922. The reason is that the Government deals only with large companies who have been wise enough not to boost their prices and the small increase at the mine has been more than offset by the decrease in railroad rates. The total cost is $12.50 per ton, but I want to make it perfectly clear that it does not follow that this would be a just price for a retail dealer to charge the domestic consumer. For example, in the Government business there is no such thing as a bad debt, and certain other fixed or general charges are charged to other departments. The Bureau of Effi-ciency made an effort to determine what would be a. legitimate handling charge for a retail dealer, in Washington, and concluded that if the Government's cost of handling was $1.00, then $1.88 would be the corresponding fair charge to pay a retail dealer carrying the same volume of business, allowing for bad debts, complete depletion and depreciation of his equipment, and 10- per cent. profit. Assuming that this is the correct differential for Washington, it does not' follow that it would be equally just for Pittsburgh, New York, or elsewhere; nor does it by any means follow that it is a fair differential this year, because the dealer, after being unable to use his equipment in the summer months, now has to deliver an unusually large quantity of coal. I merely cite this instance to show that on the basis of primary cost of coal plus railway charges the retail price is not necessarily higher this-year than last.

Jan 4, 1923

INCREASING realization that pouring and ingot-mold practices involve many factors of fundamental importance to ingot quality and general steel-mill operations has caused these phases of steelmaking to become major concerns of operators and metallurgists engaged in control of quality and costs. Methods of pouring steel from the ladle into the ingot molds have some direct effects on ingot quality. The mold itself governs solidification and dimensions of the ingot and in so doing exerts some very tangible influences not only on ingot quality but also on product yields and general steel-mill processing. In addition, practices are employed' in the handling of molds during daily open-hearth operations that are important to quality and production costs. Therefore, pouring and mold practices must be considered highly specialized and important steps in steel-mill operations. MOLD DESIGN Mold design is difficult to discuss in a precise manner because it varies greatly throughout the industry, both in theoretical concepts and practical application, and few well developed data are available. Most ingot molds are designed to meet conditions peculiar to a given plant wherein quality standards are dictated by end-use requirements, which may differ considerably, even for the same grade of steel. The mold designer must also consider the equipment available to process ingots and the product obtained from them. Such equipment, used for stripping, heating, blooming and finishing operations, is seldom, if ever, exactly the same in any two steel plants. Thus, pronounced contrasts in mold designs can be expected to continue, even among plants making strictly comparable types of product, particularly because some producers are just beginning to realize the benefits possible from specialized designs. Certain fundamentals are used in mold design but even these

Jan 1, 1951

By R. A. Flinn, John T. Norton

A CONSIDERABLE number of experiments in recent years have definitely established the fact that the internal friction or mechanical hysteresis of a metal under cyclic stress is a property that is highly "structure sensitive." Because of this fact, it has been suggested that an observation of this property, which often is referred to as "damping. capacity," might be a useful indicator of structural. changes taking place when a metal or alloy is subjected to any of a number of metallurgical treatments. Damping capacity is of interest to both engineer and metallurgist, but from a rather different point of view, and the information that each desires from such observations is of a different nature. The metallurgist is in search of various external indications of changes taking place in the interior of a metal; changes which are in themselves not directly observable. Even if the observed phenomenon cannot be explained in fundamental terms, it may be empirically related to certain characteristics of the material and prove of real value in research. Internal friction os mechanical hysteresis occupies such a position, and, although it is nor well understood in terms of basic metallic theory, an observation of itt changes can serve in a very useful capacity. Of course, there is nothing new in the measurement of damping, but the use of this property in metallurgical research constitutes a vast field, which has received all too little attention: The present work is essentially of an exploratory nature in this field and is an attempt to evaluate the process as a research tool. The phenomenon of age-hardening was chosen as a typical example of a structural change and one method of measuring damping was examined in considerable detail.

Jan 1, 1938

By Dennis V. D’Andrea, Joseph L. Condon

Laboratory crater tests were performed in two-dimensional plates and three-dimensional .blocks of Holston Limestone. Fractures in the blocks were exposed by sawing through the crater region, and a technique employing dye penetrants is described for examining the resulting fracture systems in both blocks and plates. Crater fracture patterns changed from extension of radial fractures to spa11 fractures parallel to the free face as charge depths were increased. The amount of fractured rock was found to be greater than the amount determined from standard crater volume measurements. Graphs and photographs illustrate these findings.

Jan 1, 1971

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By Gilbert Soler

Producers of alloy steels recognize the importance of chemical composition in relation to the hot-working properties and the typical surface defects found in their product. Each analysis of steel has its own peculiar characteristics. Under conditions of standard mill practice each analysis is susceptible to certain types of defects. Mill practice must be varied to obtain the best combination of surface and internal quality in the product. Chemical composition influences the cast structure and crystallization characteristics of the ingot. It also determines the rate of heating and cooling, the plastic hot-working range, and the phase structure of the steel at various temperatures. as well as the tendency toward scale formation and decarburization. This paper endeavors to emphasize the manner in which chemical composition affects the various properties of steel, and to indicate the relative importance of these factors in relation to the hot-working properties and surface characteristics of killed steel. The influence of chemical composition may be outlined as follows: I. Effect on the cast structure of steel, including: A. State of deoxidation, and type of inclusions. B. Gas content of steel. C. Freezing point and melting point of steel. D. Crystallization characteristics and segregation. 11. Effect on the hot-working properties and surface characteristics of steel, including: A. Plastic hot-working range. B. Phase structures at hot-working temperatures. C. Rate of heating. D. Cooling characteristics. E. Scale formation. F. Surface decarburization. EFferect of Chemical Composition on Cast Structure of Steel State of Deoxidation and Type of Inclu-sions.—The state of deoxidation is limited by the final chemical analysis desired in the finished product, and is controlled primarily by carbon, manganese, silicon, and aluminum, and to a lesser degree by chromium, titanium, vanadium, or other deoxidizing elements. The degree of deoxidation affects the density of the cast structure and broadly classifies the steel as killed, semikilled, or rimming. This in turn manifests itself in surface characteristics. The manner and extent of deoxidation also controls the amount, type, and distribution of nonmetallic inclusions formed. The equilibrium of manganese, silicon and aluminum with the slags and pouring refractories with which the metal comes in contact is important, especially in regard to inclusions of fire-clay origin. Some surface Seams and hot-working difficulties can be traced to nonmetallic inclusions.

Jan 1, 1941

By Reno H. Sales

Jan 1, 1914

By R. F. Stahl, W. A. Martin, R L. Huntington

A marked gravitational segregation of liquid has been observed to take place in a number of volumetric fields toward the later stages of their oil-producing periods. This phenomenon has been pronounced in thick, highly permeable sand formations such as those of the wilcox zone in Oklahoma City. This observation has prompted considerable research directed toward the semiquantitative determination of the equilibrium saturation distribution of oil vertically throughout a formation at final depletion. In this paper, data are also presented showing the transient distribution of liquid at different stages of the depletion period. Other experimental results show the effect of temperature on the drainage rates of water, Wilcox crude oil, and a close-cut heptane fraction. Intermittent drainage of liquid produced saturation gradients that might well be expected from the flow theories involved, Yields of the various liquids varied from 50 to 75 per cent of the original fluid content of the sand-packed (4 in. by 8 ft.) vertical tube. Introduction In certain volumetric Oil fields the performance of the reservoir during the latter part Of its producing life is governed to a large extent by the downward movement of liquid due to the force of gravity. This is especially true of formations having thick or tilting beds of uniformly high permeability, free of shale breaks. Laverett4 and Katz3 have presented original data and discussed the theory relating to the capillary and gravitational forces acting On liquids contained in a sand body. These investigators have pointed out the importance of such studies in the estimation of future reserves as well as the original fluid content of a reservoir. In this previous work, no data have been reported showing the history of saturation distributions during the drainage period. Since a knowledge Of these transients is helpful in obtaining crude Oil from such a reservoir, the authors have obtained these data during this investigation. Experimental Apparatus The drainage tests were carried out in two vertical tubes, 8 ft. high and consisting of 2-in. and 4-in. standard wrought-iron pipe, respectively. Each tube was equipped with a water jacket, which could be kept virtually isothermal ( ± 1.0ºF.). A diagrammatic sketch of the 4-in. tube and its auxiliaries is shown in Fig. 1. At 6 in. above the base of the tube, and at every foot above this point, core nipples were inserted through the water jacket. These nipples were closely fitted with steel-plug inserts during each drainage run. At the end of the run, these inserts were removed so that cores could be obtained from the sand-packed tube.

Jan 1, 1943

By R. F. Stahl, W. A. Martin

A marked gravitational segregation of liquid has been observed to take place in a number of volumetric fields toward the later stages of their oil-producing periods. This phenomenon has been pronounced in thick, highly permeable sand formations such as those of the wilcox zone in Oklahoma City. This observation has prompted considerable research directed toward the semiquantitative determination of the equilibrium saturation distribution of oil vertically throughout a formation at final depletion. In this paper, data are also presented showing the transient distribution of liquid at different stages of the depletion period. Other experimental results show the effect of temperature on the drainage rates of water, Wilcox crude oil, and a close-cut heptane fraction. Intermittent drainage of liquid produced saturation gradients that might well be expected from the flow theories involved, Yields of the various liquids varied from 50 to 75 per cent of the original fluid content of the sand-packed (4 in. by 8 ft.) vertical tube. Introduction In certain volumetric Oil fields the performance of the reservoir during the latter part Of its producing life is governed to a large extent by the downward movement of liquid due to the force of gravity. This is especially true of formations having thick or tilting beds of uniformly high permeability, free of shale breaks. Laverett4 and Katz3 have presented original data and discussed the theory relating to the capillary and gravitational forces acting On liquids contained in a sand body. These investigators have pointed out the importance of such studies in the estimation of future reserves as well as the original fluid content of a reservoir. In this previous work, no data have been reported showing the history of saturation distributions during the drainage period. Since a knowledge Of these transients is helpful in obtaining crude Oil from such a reservoir, the authors have obtained these data during this investigation. Experimental Apparatus The drainage tests were carried out in two vertical tubes, 8 ft. high and consisting of 2-in. and 4-in. standard wrought-iron pipe, respectively. Each tube was equipped with a water jacket, which could be kept virtually isothermal ( ± 1.0ºF.). A diagrammatic sketch of the 4-in. tube and its auxiliaries is shown in Fig. 1. At 6 in. above the base of the tube, and at every foot above this point, core nipples were inserted through the water jacket. These nipples were closely fitted with steel-plug inserts during each drainage run. At the end of the run, these inserts were removed so that cores could be obtained from the sand-packed tube.

Jan 1, 1943

By A. W. D. Hills, M. R. Moore

An apparatus has been developed in which metals can bc solidified under closely controlled unidirectional heat flow conditions. The metals are cooled by a multiple-air jet system, designed so that the heat transfer coefficient is uniformly distributed over the cooled surface. They are contained in a special furnace system of low thermal mass which enables unidirectional heat flow conditions to be rigorously maintained for certain specific cooling rates. This apparatus has been used to study the solidijication of pure lead and pure tin at zero superheat, solid metal thicknesses being determined by thermal analysis, and by dipstick readings. Detailed thermal balances have been drawn up on the experiments in order to determzne the cooling conditions that most rigorously correspond to unidirectional heat flow. Solid metal thicknesses, measured experimentally for these conditions, have beetz shown to agree closely with the theoretical wedictzons of different integml-profile methods. lt is concluded that any errors inherent in the integval-profile method are no greater than the errors inherent in experimental investigations of solidification. A knowledge of the influence of heat transfer rates on the solidification of metals is essential to the understanding and control of industrial casting processes. Since very few formal methods are available for solving the heat conduction equation under solidification conditions several authors have developed approximate techniques for doing so. One of the most promising is the integral-profile technique that has been used by Goodman,1 Hills,2,3 Tien4 and Hills and ~oore' to predict solidification rates under certain specific heat transfer coniditions. In the first of this present series of papers6 Hills has further generalized the method and developed a universal integral-profile technique that can be used to predict solidification rates under a wide variety of unidirectional heat flow conditions. Since the method is approximate it is necessary to investigate the accuracy with which it predicts actual solidification rates. A review of the literature7 shows that solidification rates have seldom been measured under accurately known heat transfer conditions and it was therefore decided to develop experimental techniques that would enable this to be done. Results obtained would then be available as a check on the approximate solutions already developed, and in the development of further solutions that would be applicable under more complicated conditions. The initial work in this experimental program which is described here, is concerned with the solidification of pure metals at zero superheat under unidirectional heat flow conditions. Subsequent experiments have been concerned with the solidification of pure metals at appreciable superheats, under varying unidirectional heat flow conditions and under two dimensional heat flow conditions. In a series of experiments recently initiated, the solidification of binary alloys is also being investigated. The results of these subsequent experiments, together with relevant theory, will be described in later papers. The solidifying metal has been cooled in all the experiments, by a multiple air jet system designed so that the heat transfer coefficient to the cooled surface is constant and is uniformly distributed over the surface. This type of system has been chosen since only one parameter is needed to specify the heat transfer conditions and since these conditions are analogous to those met in certain continuous casting processes.' Air cooling was chosen in preference to water cooling, however, since it offers a wider range of heat transfer conditions, and since it can be investigated by analogous mass transfer techniques. The first part of this paper discusses the existing integral-profile solutions that correspond to the heat transfer conditions used in the experiments, and describes the development and use of the experimental apparatus. In subsequent sections the heat transfer and solidification results are presented, and the various theoretical predictions are compared with them, and with one another.

Jan 1, 1970