Search Documents

By J. C. Purcupile, R. L. Morris

Present methods of roof support require that first a hole must be drilled, and then a toggle belt or grouted resin bolt be set. Automating this system is very difficult. Therefore, we decided to develop a system which would insert pins into the roof in one step. We think that this type of system can be automated much easier. It would then speed up the roof bolting operation and eliminate the need for a man to work under unsupported roof, making roof bolting a much safer job. There are two ways that a pin can be inserted in a mine roof without drilling a hole. It can either be pushed in, using a very high, constant axial force; or it can be hammered in like a nail. The former method involves very high compressive stresses in the pin, and requires complicated machinery to prevent buckling. Since hammering the pin does not require high axial forces buckling is not as likely. Also, experiments have shown that there are no problems associated with getting the pin to go in straight. We chose to develop the second method. While investigating methods for hammering a pin into a mine roof, we learned that piles were being driven 10 times faster than by conventional methods with a method called "orboresonance." We decided to turn the pile driver upside down, and drive pins up into the mine roof. Sonic Pin Setting Machine The machine consists of a steel bar supported at the nodal points of its first mode of transverse vibration (Fig. 1). A mechanical oscillator, driven by a hydraulic motor, is attached to one end of the bar. This provides the forcing function for the vibrations in the bar. The hydraulic power is supplied by a portable unit. When the forcing function is near the natural frequency of the bar, large amplitudes of vibration occur and require little power input. An anvil is attached to the bar at a point of maximum deflection, providing a means for striking the pin. Since the bar is being driven near its natural frequency, it takes little energy to accelerate the bar back and forth between each hit. This means that most of the power being put into the bar is going into driving the pin. This is unlike conventional pile drivers which use most of their power to accelerate the hammer back and forth between hits. The resonant frequency of the bar we used is about 250 Hz, which is in the audible range, hence the term "sonic pin setting machine." The system benefits are: (1) elimination of the two-step drilling and pin-setting roof bolt operation, (2) increased speed, (3) more intimate contact between the formation and bolts, (4) less expensive roof bolts, (5) higher integrity, (6) potential for automatic operation. Modifications During the months from Oct. to Dec. 12, 1974, under U.S. Bureau of Mines grant No. 00144104, "Projects on Coal Extraction," six members of the senior class at Carnegie Mellon University designed and built the experimental machine. They drove three pins into the Safety Research coal mine at Bruceton, Pa., and determined that the project was worth continuing. In January 1975 we began making modifications and repairs in preparation for a more extensive program of testing at Bruceton. The major items were: 1) Design and build a collapsible pin guide to keep the pin parallel with the line of travel of the lift table. 2) Move the anvil to the center of the bar. 3) Refinish the nodal holes and install new node pins and bushings. 4) Realign the bar in its frame. 5) Install a relief valve on the lift unit to control the upward force. The upward force that we exert on the pin is relatively small, so there is no tendency for it to buckle. This means that all we need to do is hold the pin straight during its initial penetration. This allows the bushing to travel up and down in a straight line. At the beginning of penetration, the bushing

Jan 1, 1977

By FRED T. WILLIANS

INTRODUCTION. THE Park City mining-district is distinctively a camp of few properties, 5,000 acres, or one-third of the entire district, being under the management of but three companies. As a rule, the ore-bodies lie deep, with no outcrop, except where erosion has formed the deeper canyons and gulches. Ontario canyon exposed the famous Ontario ledge, and Woodside gulch showed the first ore of the Silver King Coalition mine. The Quincy ore-bodies were first brought to light in upper Empire canyon, and Thaynes canyon was instrumental in aiding the prospector during the early days of the camp. There are 22 shafts which have reached a depth of at least 500 ft., ten a depth of 1,000 ft., five a depth of 1,300 ft., and two a depth of 2,000 ft. The amount of lateral development has been proportionally extensive, including six long tunnels, four of which are in 3 miles, with a fifth now being driven. The Ontario lower drain-tunnel is now more than 4 miles long. The formations are sedimentary, dipping about 30° NW. and N., and traversed by many fissures, dikes, and faults. The principal ore-bodies are found associated either with the contact of the basal Ontario quartzite and the overlying limes, or on a quartzite stratum within the limes, or in the fissures, or along some of the porphyry dikes. The district covers the intersection of the Uintah and Wasatch ranges, which explains the existence of large folds and faults, and fissures of great length, width, and depth. In a general way, the geology of the district consists of a basal quartzite dome, which has been exposed by erosion at the Ontario property. The Ontario fissure lies entirely within this formation. Flanking this dome on the west, north, and east lie

Jun 1, 1911

FRIENDS of the late Charles F. Rand presented in 1930 a sum of money from which the income is available to support various phases of the work of the Institute in which Mr. Rand was so deeply interested. At present the fund amounts to $10,400. The specific terms of the deed of gift are as follows: "The fund collected to establish a memorial to the late Charles F. Rand shall be placed in the custody of the Board of Directors of the American Institute of Mining and Metallurgical Engineers, to be set up as a trust to be known as the `Charles F. Rand Foundation,' the income of which shall each year be applied to a distinct purpose to be decided upon in that year by vote of the Board of Directors. This purpose shall be such as to promote the general welfare of the Institute and to constitute a permanent memorial of the usefulness of Mr. Rand, who for many years gave unstintingly of his time and talents in its service. "It shall be within the discretion of the Board of Directors to establish a medal to be known as the Charles F. Rand Memorial Medal to be awarded at such a time and under such rules as may be determined by the Board of Directors, for Distinguished Achievement in Mining Administration." The establishment of this medal was announced at the annual meeting in February, 1932, the term "mining" being defined in its broad sense to include metallurgy and petroleum. Robert Linton is chairman of the Charles F. Rand Foundation Award Committee.

Jan 1, 1944

By W. F. Flanagan, K. R. Evans

The strong temperature dependence of the flow stress of bcc metals has prompted considerable interest and controversy concerning the rate-controlling influence of the Peierls' mechanism upon deformation in metals.18"21 Dorn and Rajnak" recently offered a criterion for Peierls' deformation utilizing a line-energy model of a dislocation to estimate the saddle-point activation energy, for the nucleation of a pair of kinks as a function of applied stress and the height and shape of the peierls9- barrier. It was found that Un/2Uk, where 2Uk is the excess energy of a kink pair, was a unique function of where is the effective stress and 7p is the Peierls' stress as defined in Fig. 20. The relationship found by Dorn and Rajnak between is given by the solid line of Fig. 21. may be expressed in terms of the temperature of test, T, and the athermal temperature, T,, defined in Fig. 20. Considering the strain-rate, 9, of deformation for a thermally activated process to be given by where fo is nearly a constant, it is seen that and the theoretical relationship of Fig. 21 may be examined with readily obtainable experimental parameters. Dorn and Coworkers analyzed a large amount of experimental data in this manner for materials sus-

Jan 1, 1967

By William P. Blake

THE phenomena of concentric arrangement of minerals in rock-masses, generally known as "orbicular structure," have of late received much attention from investigators. Lawson, of the University of California, has described the orbicular gabbro at Dehesa, San Diego county, Cal. Kessler and Hamilton, of Stanford University, working independently upon the same subject, published their descriptions,2 giving also a list of many other localities in Europe and America where orbicular rocks are found, adding copious references to the literature of the subject. The orbicular diorite of the type locality in Corsica., familiar to mineralogists and petrologists under the name "Napoleonite," was described by Vogelslang in 1862.3 Chrustschoff, of St. Petersburg, has also given much atten¬tion to the subject, and is the author of a classification of the various known forms of orbicular structure.4 No complete and satisfactory explanation of the origin of or¬bicular aggregations in rocks has yet been offered. The patent fact is generally recognized that the constituent minerals have crystallized from a more or less molten or plastic magma, but why these minerals should be arranged in concentric spheres or crusts has not been clearly shown. Vogelslang, for example,

Jul 1, 1905

By H. Kenworthy, R. B. Fisher, R. G. Knicherbocker, M. M. Fine

The progress made to date in the mineral dressing of complex Arkansas titanium ores is reported in this paper. Concentrates of rutile, a dioxide of titanium, were produced by treating a submarginal ore from the Magnet Cove Rutile Co., Inc., Magnet, Ark. The rutile recovery at present is 45 to 50 pct of the total TiO2, with the possibility of increased recovery with additional research. The work reported herein is part of a general study which will later include results of investigation of other titanium ore bodies in the Magnet, Ark., area. The fragile character of the rutile minerals, the softness of the gangue, the occurrence of pyrite and leucoxene, and the considerable proportion of extremely small size rutile in the presence of montmorillonite- and illite-type clays in the Magnet Cove open-pit mine are the important factors in the mineral dressing of this submarginal rutile ore. History The occurrence of titanium minerals in the Magnet Cove area of Arkansas was recognized as early as 1890, but it was not until about 1912 that any appreciable prospecting for the minerals was undertaken. At that time drilling was begun, a shaft was sunk, and several drifts were driven, but beneficiation to recover the titanium minerals was not attempted. The only successful mining and milling operation of the Magnet Cove rutile deposit was begun in 1932 by the Titanium Corp. of America and continued until 1942. The ore was washed by means of a rotary scrubber and then deslimed in a drag classifier. The discharge was ground in a rod mill, classified, and tabled to recover a rougher rutile concentrate, which was screen-sized and retabled on cleaner tables. The cleaner concentrates were given a reducing roast, screen-sized, and magnetically separated to produce a finished rutile concentrate. Most of the rutile produced during this period was sold abroad. In 1942, the Titanium Alloy Corp. of Arkansas (a subsidiary of the Titanium Alloy Manufacturing Co. of New York) purchased the property and rebuilt the mill. Subsequently, the plant and property were acquired by the Magnet Cove Rutile Co., Inc., of Little Rock, Ark., the present owners. Very little titanium has been produced since 1942. Although the Titanium Corp. activities yielded enough returns to allow continued operation for approximately 10 years, certain factors must be recognized. These are: (1) production of rutile in that period was during a low in the economic cycle which permitted low-cost operation on a small scale, and (2) a considerable portion of the production was above the water level and no drainage problems existed. Prior to this paper there has been no published report of any mineral-dressing investigation of the lower levels of the ore body. Reference is made in another paper1 to an earlier investigation of Magnet Cove rutile by the Rolla laboratory, in which it is stated that recoveries of 12 to 17 pct of the rutile were obtained. The present investigation was undertaken to improve the known milling processes and to provide adequate metallurgical information about the ore treatment. Titanium Technology The titanium mineral of primary interest in the present investigation was the titanium dioxide, rutile. Rutile is one of the industrial minerals whose annual consumption is relatively small but strategically important. The domestic production of rutile was 7100 tons in 1948. The imports of rutile in the same year were approximately 8000 tons.2 A major use of rutile is in the production of welding-rod coatings, for which a product containing a minimum of 92 pct titanic oxide is desired. Other constituents, such as lime, silica, and sulphur, must be held to a minimum, but hard-and-fast specifications for these elements cannot be drawn. It is necessary to incorporate the rutile in a welding-rod coating, make a sufficient number of test welds, and then determine the tensile strength of the weld metal in the as-welded and stress-relieved conditions. Such a test gives

Jan 1, 1950

By D. R. Bomberger, M. Deul

An automatic microscope has been developed to measure the size and populations of macerals and minerals in fine coal particles. Differentiations are made on the basis of reflectance. This study is concerned with the size distribution of pyrite inclusions. Most fine coal cleaning processes do not remove pyrite as completely as a straight density separation. Consideration of the pyrite size distribution is suggested as a more accurate method of predicting sulfur reduction by a cleaning process. Analyses of float-sink results and Deister Table operation in terms of pyrite particle sizes are made. Other potential applications of automatic microscopy are also discussed. In the study of coal cleaning by pseudo-gravity methods (tables, cyclones, hydrotators, etc.), it is customary to express the deficiency of the process relative to float-sink measurements in some form of "percent efficiency". These have been calculated in many different ways in order to provide a means of extrapolation of test data to untested coal feeds. This works quite well with coarse coal (here defined as larger than one-eighth in.). Large, heavy pieces of refuse are rejected rather thoroughly by many cleaning processes, and the efficiencies relative to float-sink results approach 100%. In coarse coals, the difference in the sizes of fine pyrite is masked by the averaging effect of the large coal envelopes. The existence and fate of fine pyrite is often hidden in the larger numbers representing coarse (and easily removed) pyrite. There are cases where it is desirable to subject fine coal (here defined as smaller than one-eighth in.) to cleaning processes. This is true of naturally occurring fie coal streams and in cases where comminution followed by cleaning is necessary to provide the quality desired. It is in this area that the use of process efficiency relative to float sink fails. Percent efficiencies decline to very low figures, and equivalent separation densities become a matter for conjecture. The net result is that an attempt to estimate product quality from float-sink data and a process efficiency figure often results in large errors. This work represents a new approach to the problem by observing the fate of pyrite particles, grouped by sizes, in a cleaning process. Examples are given which relate pyrite size measurements to float-sink washability and to a Deister Table operation. EXPERIMENTAL WORK The automatic microscope used here has been previously described.' Briefly, it is an instrument which measures the diam of particles (as defined by a range of reflectance) exposed on a polished specimen. The instrument scans a sample briquet, measures diam of exposed pyrite inclusions and records the data by size intervals. Preparation of the briquet is critical, due to the automatic nature of the process. The principal requirement is for an optically flat surface, so that focus will be maintained as the motorized stage moves the specimen under the lens. The various substances present must be polished to the same level in spite of the wide difference in hardness between coal substance and minerals. The polishing method must not pluck out small grains, which might be rather loosely held by surrounding coal. The procedure below was successful in producing all of these results. The coal sample (8 mesh or finer) was riffled (a micro vibrating riffle is essential) to obtain 15 g. One volume of Lucite powder (thermosetting plastic mounting medium) was mixed with three volumes of coal and mixed thoroughly. A briquet was formed using a cylindrical die (1 1/4 in. diam) at 3000 lb per in.* pressure and 150°C. Preparation of the optical surface was accomplished on automatic polishing equipment, according to the following schedule: 1) Grinding: 3 stages, using successively fine Carborundum grits of 180, 320 and 600 mesh. 2) Rough polishing: 2 stages, using 3µ alumina on cast iron, followed by 1µ alumina on lead. 3) Fine polishing: 2 stages, using 0.5µ alumina on napless broadcloth over bronze, followed by 0.1µ alumina on silk filament cloth over bronze. Raw data were corrected for the fact that the chords

Jan 1, 1964

By R. W. Nash, A. E. Schwaneke, V. R. Miller

The Bureau of Mines developed a detector for controlling sorting devices to separate the copper-bearing fragments from the barren portion of Michigan native copper and western prophyry copper ores. A successful sorter could be used to preconcentrate the ore and eliminate costly hoisting or hauling of waste. An induction balance unit was developed and used in sorting tests on crushed sized - 2.5 + 1. 3-cm (- 1 + 1/2- in.) ores from the Kingston (0.9% Cu) and Centennial (1.6% Cu) mines of Upper Michigan. Concentrates of 4.0% and 7.5% Cu, respectively, were obtained at recoveries of 85 and 80% of

Jan 8, 1978

By C. H. North, L. E. Lynd, W. W. Anderson, H. Sigurdson

CONSIDERABLE uncertainty is revealed in the literature regarding the nature of the titanium minerals which make up the bulk of the heavy, opaque fractions of numerous beach sand deposits of the world. An investigation was made, therefore, of beach sand concentrates of North Carolina, Florida, Brazil, and India. Magnetic concentration, X-ray, and microscope data were obtained which show that these concentrates consist essentially of ilmenite and its alteration products. The alteration, brought about by oxidation and leaching of iron values, has resulted in upgrading the ores to a range of 56 to 64 pct TiO2, as compared with 52.7 pct in ilmenite of theoretical composition. Conclusions drawn regarding the nature of the dominant titanium-bearing mineral in beach sand deposits have been based mainly on chemical composition, specific gravity, and petrography. This material has usually been referred to as ilmenite or weathered ilmenite. It has also been referred to as arizonite because in chemical composition it resembles an occurrence in Arizona which was described by Palmer1 in 1909.

Jan 8, 1954

By R. W. Wittkopp, J. D. Stephens

In a device known as the electron-beam microprobe, the mining industry has lately acquired a sophisticated new analytical tool that can dig out answers to a broad range of questions spanning all phases of mining activity. Essentially, the microprobe is a specialized X-ray fluorescence unit that makes it possible to obtain chemical analytical data for volumes as small as 1 cup. With this capability, it can be used both for determining the composition of small inclusions in rocks or metallic products and for monitoring changes in composition that proceed from a reacting surface. At the Research Center of Kennecott's Metal Mining Division, this versatile probe has successfully solved problems in mineral operations ranging from exploration through refining. A few instances of how the probe has been applied at the Center are presented here. In Mineral Exploration-A Good Look Before Leaping Since the objective of mineral exploration is to locate deposits of materials which can be processed at a profit, the mode of occurrence of elements or minerals in the deposits is important.

Jan 1, 1970

By G. L. Coleman, D. S. Hutton, W. C. Leslie

The occurrence of twins in a iron, generated during cooling through the ?-a transformation, is well established,1-8 but this phenomenon has been nearly ignored during the past 20 years. It is the purpose of this note to call attention to the prevalence of such twins and to illustrate their appearance. The work of paxton7 and Kelly8 has demonstrated beyond reasonable doubt that for Neumann bands (mechanical twins) in a iron the twinning plane is (112) and the twinning direction <III>. The agreement with McKeehan&apos;s earlier work4 on transformation twins indicates that both types of twins in ferrite follow the same twinning law. There is little doubt of this conclusion, but it could be strengthened by a microbeam X-ray determination of the orientation relationship between a single ferrite grain and a transformation twin within that grain, as in the technique used by Kelly8 on Neumann bands. RESULTS AND DISCUSSION Transformation twins, identified by their appearance on a polished and etched section, were found in

Jan 1, 1960

By L. J. Trilli

RECENT studies have indicated that there may be considerable difference in the cleanliness of the central pipe cavity of open top ingots. It has been speculated that some of this difference arises becausk of reactions that occur during reheating in the blooming mill soaking pits. In this respect, it has been recognized that an oxide coating or flow of slaggy material in the cavity could inhibit welding during hot rolling and thus reduce the amount of sound product which may be obtained. This note is intended to summarize some observations on the structure of a split ingot top which may be useful in describing a mechanism whereby the shrinkage cavity could be oxidized during reheating. A 221/2x241/2 in., big-end-down, test ingot was secured from a routine production heat. The chemical analysis representing this ingot is as follows: 0.08 pct C, 1.04 pct Mn, 0.062 pct P, 0.315 pct S, and 0.02 pct Si. The deoxidation practice used on the heat from which the experimental ingot was

Jan 1, 1957

By J. M. Lohr

A COMMERCIAL development requiring a suitable alloy or alloys for sealing into various grades of glass made it desirable to have a more exact knowledge of the expansion characteristics of the nickel-iron alloys than appeared in the published literature. The expansion of the more common. FIG. I.-EXPANSION CURVES OF SEVERAL FIG. 2.-EXPANSION CURVES OF TWO TYPES OF GLASS. (Courtesy of R. C. A.) TYPES OF GLASS. (Courtesy of R. C. A.) types of glass under consideration varies from 2.7 to 10.4 X 10-6 per degree Centigrade, over the range 20° to 400° C. For reference, the thermal expansion curves f several types of glass used for sealing by the lamp and tube industries are given (Figs. 1 and 2). This paper covers a detailed investigation of the thermal expansion of a series of nickel-iron alloys in which the nickel content varies from 30 to 70 per cent. Particular stress is laid on the alloys that contain between 40 and 55 per cent Ni.

Jan 1, 1938

By J. A. Elias, A. J. Heckler

A simplified method is described for the prepauatior~ of comnposite samples for determination of one quadrant of an X-ray pole figure of a sheet material by the Schulz reflection method. Other special conzposite sampling methods were used to investigate specific areas of the pole figures. Plotting nets for these sampling plans were drawn by a computer. Step-scanning techniques were used to obtain detailed information about specific regions of a pole figure. Satisfactory pole figures were obtained for large-grained (0.5 to 1 in. diam) sheet materials. COMPOSITE sampling techniques for preparing one quadrant of an X-ray pole figure have been reported by a number of authors.&apos;-5 All of these methods are similar in that they use a composite sample prepared by stacking and holding together coupons cut from a sheet material. The schulze reflection technique is applicable to the composite sample so that only minor corrections are needed for defocusing and absorption effects. Also, a relatively large area of a sheet is sampled through the use of multiple cross sectional pieces. In general, sampling methods necessary to obtain a composite-type specimen have been formidable enough to discourage their use in routine pole figure determinations. This paper presents a versatile sampling technique which is simpler than those previously described along with an accurate method for obtaining stereographic plotting nets for any orientation of a composite specimen surface. A step-scanning technique is used to obtain more quantitative determinations of specific regions in pole figures, and the composite technique is satisfactorily applied to determine pole figures of very large grained sheet materials. REVIEW OF PREVIOUS TECHNIQUES Mueller and ~nott&apos; first proposed a technique for obtaining one complete quadrant of an X-ray pole figure by using a sheet sample and six different composite samples in which the individual coupons were aligned and held together by two types of jigs. Data from the seven different samples were overlapped to obtain a single quadrant. ~eieran~ and Lopata and ~ula~ obtained a complete quadrant of a pole figure from a single sample prepared by forming a cube from coupons cut from a sheet. These coupons were bonded together using an epoxy cement, and a cut was made at 54.7 deg to the normal, transverse, and rolling directions of the sheet, Fig. I. The normal direction of the cut face projects into one quadrant of a stereographic projection at equal angles to the three principal orthogonal reference directions mentioned above. X-ray reflection data obtained along a spiral path in physical space could then be plotted on a stereographic net offset 54.7 deg from the normal, as shown in Fig. 2. A rotation about an axis representing the surface normal is designated as a, and a rotation about an axis lying in the plane of the surface is 4. From Fig. 2 it is apparent that a tilting angle of no more than 55 deg @ is necessary to obtain the complete quadrant. ~eber~ devised an improved sampling technique by cutting coupons 45 deg to the rolling direction of a sheet, stacking and bonding these with an epoxy cement at an angle of 54.7 deg to a reference plane, and finally grinding and lapping a flat specimen surface parallel to this plane. An important consideration of this technique and that of Lopata and ~ula~ is variation in the diffracting power of the specimen surface due to the bonding medium. While any composite-type sample will have some such variation due to boundaries between coupons, the problem can be minimized by elimination of the bonding medium and by avoiding prolonged etching times which could lead to significant inter lame llar attack of the coupon faces. EXPERIMENTAL TECHNIQUE We were working concurrently though independently on a technique similar to ~eber&apos;s,&apos; but which does not

Jan 1, 1968

By C. Chu

A theoretical investigation has been made of the forward combustion process using a one-dimensional linear mathematical model, taking into consideration the effect of the vaporization-condensation which occurs on the leading edge of the heat wave. This work involves the solution of five coupled partial differential equations. Besides the vaporization-condensation phenomenon, these equations account for conduction, convection, combustion, heat loss, diffusion and bulk fluid flow. For the one-dimensional linear model studied, the vaporization-condensation phenomenon does not induce appreciable change in the temperature at the combustion front; and its primary effect is to create a steam plateau and to increase the length of the heated zone ahead of the combustion front. This effect becomes more pronounced at lower pressures, higher porosities or reduced gas saturations. The peak temperature and the temperature profile on the leading edge of the heat wave stabilize after a certain period. The length of the steam bank remains practically constant, although the length of the water bank increases as the heat wave advances. INTRODUCTION The existence of the vaporization-condensation phenomenon in the heat-wave process and the important role played by the phenomenon have been recognized by several investigators. Kuhn and Kochl stated that steam plateaus were frequently observed on the temperature records of their experiments. The steam plateaus were attributed primarily to the vaporization and subsequent condensation of the interstitial water existing in the oil sand. Szasz2 suggested that both lighter hydrocarbons and water are vaporized on the leading edge of the heat wave, carried forward in the gas stream, and then condensed to create banks of oil and water. Martin et al suggested that the vaporization-condensation phenomenon is one of the main mechanisms of the heat-wave process, along with thermal expansion and viscosity reduction. Wilson et al. reported the existence of a steam plateau several inches in length in their small-scale tube-run experiments. However, this important phenomenon has never been taken into consideration in the numerous theoretical analyses by various authors. 5 The purpose of this work was to study the thermal aspects of a linear heat wave, taking into consideration the vaporization-condensation on the leading edge of the wave, to determine the effect of this phenomenon on the temperature profile of the reservoir, and to investigate how this effect varies when other process variables are changed. THEORY We consider a reservoir of porous medium of cross-sectional area A, extending from x = 0 to x = L. This reservoir contains, aside from the solid matrix itself, a gas phase and a "combined liquid phase" which is a combination of two immiscible liquid phases — namely, an oil phase and a water phase. The oil present in the reservoir is assumed to consist of three fractions, a noncondensable gas, a nondistillable residuum, and a vaporizable oil fraction which may be present in both the gas phase and liquid phase. Before the heat-wave process begins, preheating has taken place and has imparted an initial temperature distribution T,(x) to the reservoir. At the start of the process, a stream of oxygen-bearing gas is introduced through the face at x = 0. This gas supports the combustion of the residual fuel and supplies the heat throughout the process. In order to develop a tractable system of equations, the model properties are postulated as follows: (1) the system is isotropic and homogeneous; (2) there is a uniform fuel content throughout the reservoir; (3) combustion takes place in a moving vertical planar region of infinitesimal thickness; (4) the temperatures of the fluids and the solid matrix are identical; (5) radiation is negligible; (6) the gas and liquid saturations are uniform throughout the reservoir and remain unchanged

Jan 1, 1965

By R. A. Graham, R. W. Rohde, J. R. Holland

In a shock wave compression study of a martensitic Fe-30 pct Ni alloy, Graham, Anderson, and Holland&apos; found a region of unusual compressibility extending from a few kilobars up to about 20 kbars. This region was characterized by a continuously decreasing shock wave velocity with increasing stress. In this note, we report the results of a study initiated to determine the source of this unusual compressibility. In earlier shock-loading experiments on martensitic Fe-30 pct Ni, Loree et a1.&apos; determined that a phase change occurred at about 80 kbars. Subsequently, Bowden and elly found that samples of a similar material shock-loaded at about 100 kbars experienced a martensite-to-austenite transition. Their crystal-lographic analysis showed the transition was a direct reversal of the established martensite system to the austenite phase. The shock loading in the present experiments was accomplished by precisely controlled plane impact between two discs of the sample material. This configuration created a state of uniaxial strain in the two the front of a projectile which was accelerated to various velocities. Planarity between the impacting discs was controlled to 5 x 10-4 rad, and impact velocities were measured to 0.5 pct. From a knowledge of the Hugoniot relationships of the material and the impact velocity, the shock-wave stress can be calculated. Samples were shocked at 18, 50, 70, and 100 kbars. The specimen discs shocked at 18 and 50 kbars were instrumented with quartz gages to observe the stress time profile. A more detailed description of the experiment has been given previously.4 The shock-loaded specimens were recovered intact by decelerating them in a catcher filled with soft wood. Discs of Fe-30 pct Ni nominally 12.7 mm thick and 64 mm in diam were cut from bar stock. Chemical analysis of the material provided the following composition in weight percents: 29.5 Ni, 0.50 Mn, 0.21 Si, and 0.10 C, with traces of Cr, Cu, Mo, Al, and Co. The discs were austenitized at 650° C for 2 hr at a pressure of less than l0-&apos; torr, and furnace-cooled. Martensite was then produced by quenching the discs at -196" and holding 168 hr. The initial martensitic structure formed is shown in Fig. l(a). Typical microstructures of samples shock-loaded at 18 and 100 kbars are shown in Figs. l(b) and l(c). The banded structure with the austenite regions running parallel to the shock propagation direction was characteristic of samples shock-loaded at all stresses. No such banding was found in samples that were not shock-loaded. Comparison of Figs. l(b) and l(c) shows that, although under the optical microscope the two microstructures are quite similar, the martensite plates of the specimen shocked at 100 kbars etched in a distinctly different manner. This unique etching behavior of martensite in samples shock-loaded above the 80 kbar transition point has also been observed by Leslie el al.&apos; These investigators determined from X-ray and electron microscope studies that fcc martensite, similar in appearance to normal bcc martensite, had been formed under shock loading. A quantitative determination of the amount of austenite present after shock loading was made by X-ray techniques. Both the methods of Lindren&apos; and Miller&apos; were utilized. The results are shown in Table I. The error limits are those experimentally observed from two independent analyses of each sample and represent the precision of the experiment. The absolute error, which should be similar for each sample, is believed to be about 10 pct. It is seen that as the shock stress increases the amount of austenite present also increases. On the basis of the X-ray and microscopic observations, we conclude that shock loading below the 80 kbar ersal will initiate a martensitic reversal: the amount of reversal that occurs increases with in-

Jan 1, 1969

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By Elmer A. Jones

Development work in mines of St. Joseph Lead Co., Southeast Missouri, using trackless loading equipment shows definite advantages: Speed of cleaning, ability to work on steep grades and sharp crosscuts, good later tracking conditions, and possibility of wasting rock in old abandoned stopes. THE Desloge mine is one of a group of mines owned by the St. Joseph Lead Co., in the so-called Lead Belt of Southeast Missouri. It has been operating approximately 40 years producing a daily tonnage ranging from 1600 to 3800, depending on various factors. On an average, the present mine is 300 ft deep with an extreme extent of 2.7 miles by 1.7 miles. Most of the present mining is in the lower horizons of the Bonne Terre dolomite, a fairly soft rock requiring no support except occasional channel iron and roof pins. Due to the contour of the underlying sandstone and porphyry, some development work has been through short stretches of these different formations. In some areas the lower part of the dolomite is quite sandy and generally is considered abrasive. Sizes and Methods of Drifting Have Changed: Development work has, like other phases of mining, changed considerably in the last 20 years, from cleaning by hand to the use of a mechanical method. The conception of a standard drift has also changed. Before the advent of mechanical loading in stopes there were many pieces of main line drift averaging 7 ft high x 9 ft wide. With the coming of the St. Joe shovel the drift was increased to 8 ft high x 10 ft ELMER A. JONES, Member AIME, is Assistant General Mine Superintendent, St. Joseph Lead Co., Bonne Terre, Mo. AIME Columbus Meeting, September 1949. TP 2859 A. Discussion (2 copies) may be sent to Transactions AIME before July 31, 1950. Manuscript received Sept. 16, 1949. wide. Now with the Joy loader and shuttle car, a 9x11 ft drift is coming to be standard size. Methods of cutting drifts have changed considerably over the last few years. Some changes in drilling equipment have been made such as reducing the weight of column, clamp, air feed, and fittings to go with the HC10 Cleveland jackhamer. Other changes have been made in drill steel such as the use of detachable bits; throw-away variety, screw type, and the tungsten-carbide insert bits. Later developments have introduced spiral-welded pipe with victaulic couplings, millisecond exploders, bulky powder, and the use of electric cap lamps. Experimental work is going on continually in various phases of development work, some to be tried and discarded, others gradually to become standard practice. To sum up, the standard method of development now in use at Desloge is as follows: The work is done on a two-shift cycle 7:00 p.m. to 3:00 a.m. and 7:00 a.m. to 3:00 p.m. Two men known as development drillers comprise a crew on each shift. These two men arrive at their work about 7:30 to find a round blasted by the previous shift. After scaling down back and walls they proceed to the cleaning operation, using either a Joy loader and shuttle car, a drag hoist mounted on a slide ramp, or an Eimco Finlay to load into a 21/2 ton mine car. Cleaning may take from 2 to 4 hr depending on conditions such as length of round broken, length of haul, and other variables. After fitting up pipe and setting up columns and drills they are ready to drill a round which should measure 9 ft high x 11 ft wide and break from 5 to 7 ft advance. This may also take from 2 to 3 hr. Then they are ready to charge and

Jan 1, 1951

By K. Tangri, M. Chaturvedi

The addition of 0.5 wt pct Cu to Zr-2.5 Cb alloy increases the as -quenched hardness of the hexagonal martensitic a&apos; phase, produced by water-quenching bccß-Zr phase, by about 35 pct. This strengthening has been attributed to the solid -solution hardening of the matrix. On aging ternary martensite, a&apos; phase reverts to equilibrium a and Zr2Cu and ß-Cb precipitate out, mainly at the twin and grain boundaries, causing a secondary hardening of the matrix. COLD-worked Zircaloy-2 pressure tubes have been in use in power reactors for a considerable period of time. The search for a better material led to the development of Zr-2.5 wt pct Cb alloy which in the quench-aged condition develops 50 pct more strength than that of cold-worked Zircaloy-2, however, its corrosion resistance in water and steam in the temperature range of 316" to 400°C, in absence of neutron flux, is inferior to that of zircaloy-2.&apos; Work carried out by Ells et al.1 and Dalgaard2 has shown that the corrosion properties of Zr-2.5 wt pct Cb alloy can be considerably improved by the ternary addition of 0.5 wt pct Cu. This paper is concerned with the effect of 0.5 wt pct Cu on the formation of martensitic a and its aging characteristics in a Zr-2.5 wt pct Cb alloy. MATERIALS AND EXPERIMENTAL TECHNIQUES Zr-2.5 Cb-0.5 Cu (referred to as the ternary alloy) and Zr-2.5 Cb (referred to as the binary alloy) alloys, supplied by the Chalk River Nuclear Laboratories of the AECL were used. The detailed chemical analysis is given in Table I. Cold rolling and swagging with frequent intermediate anneal of 1000°C were used for the initial fabrication of the alloys. All the heat treatments were carried out after the specimens were wrapped in zirconium foils and encapsulated in silica tubes under a vacuum of 5 x 10-6 mm of Hg. For optical metallography and hardness measurements specimens were mechanically and then chemically polished in a 45 pct HNOj, 45 pct HzO, and 10 pct HF solution. Hardness was measured on a Vickers hardness tester using a 10-kg load. For each specimen at least fifteen indentations were made in order to obtain a representative value. The phase identification and structural analysis were carried out using X-rays and electron diffraction techniques. Wires of 1.5 mm diam reduced to 0.12 mm diam by chemical etching were used for making Debye-Scherrer powder patterns using Cu Ka radiation in a 114.6 mm diam camera. Carbon extraction replicas were prepared by etching the specimens, after depositing a layer of carbon on the metallographic specimen, in one part HF and thirty parts ethyl alcohol. Thin films were prepared by electropolishing heat-treated 3/4 by 1/2 by 0.005 in. thick strips using a modified Bollman-Window technique. The 10 pct perchloric acid-90 pct methyl alcohol bath was kept at -50°C and polishing was done at 5 to 10 V. The thinned specimens were washed in ethyl alcohol at -30º to -40°C and dried between filter papers. Replicas and thin films were examined in a Phillips 300 G electron microscope. For resistivity measurements thin strip specimens 0.02 by 0.3 by 10.0 cm long were used. The potential leads were spot welded to the specimens in order to maintain a fixed length for the initial and the final resistivity measurements. The resistivity was measured by a Kelvin bridge in a temperature controlled room. The temperature was maintained at 72º ±1°F and the accuracy of the resistivity measurements was 0.03 µa-cm. RESULTS As-Quenched Structures. In order to produce a homogeneous matrix to study the precipitation reaction the solution-treatments of both the alloys were carried out in the -field region. From the Zr-Cb phase diagram due to Lundin and cox3 ß/a + ß phase boundary for Zr-2.5 wt pct Cb alloy is 820°C. Ells et al.1 have reported this boundary for Zr-2.5 Cb alloy containing 1100 ppm 0 to be at 920°C. Also, the addition of 0.5 wt pct Cu reduces this temperature by 50°C. Therefore, the solution-treatments were carried out at 1000°C to ensure that the alloys were in ß-phase region. The soaking time was 1 hr and the specimens were water-quenched. The as-quenched hardness of the binary alloy was 245 Vpn whereas, that of the ternary alloy was 330 Vpn. The X-ray diffraction studies indicated that the as-quenched structure of both the alloys consists of martensitic hexagonal phase a&apos;, with a c/a ratio of 1.591, and some retained ß-Zr. The presence of a&apos; phase was further confirmed by thin film electron microscopy. Electron micrographs of typical ß-quenched structures of the ternary and the binary alloys are shown in Figs. 1 and 2, respectively. Fig. 3 shows the diffraction pattern from an area similar to that shown in Fig. 1. Although, the as-quenched hardness of the ternary alloy is about 35 pct greater than that of the binary alloy, the structure of both the alloys seems to be the same. The matrix of both alloys is heavily twinned and shows very few dislocations. Furthermore, there is no evidence of any precipitation taking place in either of the two specimens during quenching from the solution-treatment temperature. Aging Behavior of Martensitic a&apos;. The aging kinetics of the ternary alloy were followed by resistivity and hardness measurements. The as-quenched values

Jan 1, 1970

By M. M. Rao, P. G. Winchell

The growth rates of bainitic plates were measured at 400°C in Fe-Ni-C alloys containing 0.10 atom-fract~on nickel and 0.0012 to 0.0075 atonz-fraction carbon. The growth rates are adequately represented by where xc is nearly the atom fraction carbon of the bulk austenite and PXCy is nearly the carbon atom fractlon in the ferrlte of radiids p In equilibrium with austetzite. The form of the equation is that predicted by a model in which carbon diffusion in austernite controls the gvowth, but the numerical constatnt is two orders of magnitude below that suggested by the model. THE growth of bainitic plates in steel is often assumed to be controlled by the diffusion of carbon away from the advancing plate tip. This hypothesis predicts that the growth rate will increase as the carbon content of the austenite, xCz, is reduced toward the carbon content of the saturated ferrite comprising the plate tip, PxCY The growth rate should vary approximately as (xCg- pxCy)-1. Experimental observation of the growth behavior at low carbon levels should provide a significant test of this model. An alloying element in addition to carbon is required so that low-carbon austenite can be experimentally observed while undergoing bainitic transformation. Nickel was selected. The presence of nickel complicates the interpretation of the data in two ways: First, diffusion of nickel during the transformation would make analysis very difficult. Nickel is assumed immobile during the transformation. Second, nickel affects the solubility of carbon in ferrite and austenite in equilibrium. This effect has been evaluated.&apos; At the completion of our experimental work Goode-now et al.2 published data in essential agreement with the observations to be reported here. Since their discussion is abbreviated and their data are scanty in the region of interest, we believe the present work is of significance. I) THE MODEL OF BAINITIC PLATE GROWTH The rate of lengthening of a plate is assumed to be controlled by the diffusion of carbon from the advancing ferrite-austenite interface into the surrounding austenite. The precipitation of carbides is assumed to be a secondary process. For ease of analysis the carbon-atom ratio,* pxCy, of austenite in equilibrium with ferrite which is convex with minimum curvature radius p, and the carbon-atom ratio, PxCY, of that ferrite in equilibrium with austenite are assumed independent of location on the ferrite-austenite interface. Since these carbon contents vary with the radius of curvature of the ferrite, p, their assumed positional independence must be held as an approximation. The consequences of these assumptions have been developed approximately by zener3 and Hillert,4 and the resulting equation for a platelet has been applied to bainite by Speich and cohen5 and Kaufman, Radcliffe, and Cohen.8 The Zener-Hillert equation* for plates is: The analysis of Hillert is supported by that of Hor-vay and cahn7 which involves no mathematical approximations but does include the assumption that the a/y interface coincides with an isoconcentration line. The solutions of Horvay and Cahn for elliptic paraboloids are replotted in Fig. 1. The shape of the paraboloid is expressed in terms of the ratio of the principal radii of curvature at its tip, A =p1/p2, which is also the ratio of the minor to the major axis of the elliptic cross section. The Zener-Hillert equation for plates is also plotted. The agreement is within a factor of two for (pxyaCr - xyC )/(xyC - PxCaY) between 0.5 and 100. This is the range of interest here and in most other work on bainite. The original form of the Zener-Hillert equation was the form given above with the right-hand side replaced by (pxCya -xCy)/(PxCya). This replacement is not appropriate here. 11) THE EXPERIMENTAL PROCEDURE Alloys were prepared and three kinds of experiments carried out. Continuous-cooling-transformation experiments were carried out on wires by measuring temperature and resistance during continuous cooling. Isothermal-transformation experiments were carried out on wires by measuring electrical resistance as a

Jan 1, 1968