Search Documents

By H. M. St. John

THE melting department is the heart of the foundry. From it clean metal flows to the molding floor, in the right quantity, at the right time and at a sufficiently low cost-or, if not, the foundry fails to thrive. Since it is our purpose here to discuss present-day melting practice in the foundry, it may be well at the start to emphasize the wide differences in foundries and the conditions under which they must operate in order to reach the goal stated in the first paragraph. In every foundry, large or small, jobbing or captive, the same factors must be dealt with but they are of varying consequence and must be dealt with in varying ways in different foundries. Particularly in the nonferrous industry, there is so wide a variation in the composition of alloys used and in the character of castings made that no one type of furnace, nor any one method of operation, can be expected to produce the best results at all times. The present discussion will not attempt to include all nonferrous metals. It is intended to cover only the copper-base alloys in which copper is the dominant element, most of which are commonly known as brass or bronze. The discussion is further limited to the melting of these copper-base alloys for use in sand-casting foundries. Die-casting plants, the brass-rolling mills and certain other metal industries have melting problems peculiar to those industries, which will not be considered here. The following considerations are elemental in all foundries and are listed in what is believed to be the relative order of their present-day importance: I. The melting department must meet the foundry's requirement for dean, fluid metal, of specified composition and purity, at a temperature suitable for the work the foundry has in hand. This is the prime consideration in any foundry, at any time, anywhere. 2. Working conditions surrounding the melting furnaces and attending their use must be good. 3. The cost of molten metal at the mold must be as low as possible. 4. The operating characteristics of the furnaces must be sufficiently flexible, to meet normal variations in foundry requirements. 5. The operation and maintenance of the melting equipment must not require more skill and experience than is available in the particular foundry in question. METAL QUALITY It is not a function of the melting furnace to refine or improve the quality of the metal but simply to melt it without impairing its quality. Good practice requires, therefore, that care must be taken to supply the melting department with metal of inherently good quality, assured by specification or otherwise, having all the properties necessary to produce the castings desired. An alloy contains a number of primary elements, which must be present in definite proportions if the castings made from it are to have the desired properties. If the castings are made to a customer's specification, this will state the range within which these principal elements (for example, copper, tin, lead and zinc) are permitted to vary.

Jan 1, 1946

International Trade in Nonmetallic Minerals. BY J W FURNESS AND E W PEHRSON (Man &. Met, Sept, 432 2500 words) International trade in nonmetalic minerals (exclusive of fuels) is dominated largely by fertilizer raw materials such as phosphate rock, potash, nitrates, sulphur and pyrites and the miscellaneous group of minerals including asbestos, mica, graphite, fluorspar and china clay Cost of trans¬portation deters any substantial movement of the building materials which usually occur widely in nature and are thus available near consuming centers at relatively low cost This paper, which presents a summary for 1932 of the world production, consumption and principal trade relations of asbestos, china clay, fluorspar, graphite, gypsum, mica, phosphate rock and potash illustrated by world charts, is based on an original study of 15 nonmetallic minerals conducted by the U S Bureau of Mines Practical and Legal Aspects of Mme Financing See METAL MINING Economic Significance of High-grade Concentrates See MILLING AND CONCENTRATION

Jan 1, 1937

By T. A. Read, H. K. Birnbaum

Deformation of AuCd alloys having the 8 (orthorhombic) and (3" (tetragonal) structures occurs by the stress induced motion of twin boutdaries. A restoring force acts on displaced twin boutdaries as a result of internal energy increases in the volume through which the boundaries are displaced. The phenomonology of the twin boundary motion is described and a mechanism for twin boundary motion and the restoring force is proposed. A time-dependent stabilization behavior of the twin boundaries, which is observed after the twins are formed by the diffusionless phase transformations, is described. THE AuCd 8 phase (ordered bcc structure) exhibits a transformation to a phase having an orthorhombic structure, 8' (space group D'), for compositions in the vicinity of 47.5 at. pct Cd and to a phase having a tetragonal structure, 8" (point group 4/m, m,m), for compositions in the vicinity 50.0 at. pct Cd. Both transformations are diffusionless, occur on cooling at 60" and 30OC, respectively, and are crystallo-graphically reversible.' They are accompanied by an inhomogeneous deformation which was observed to be twinning in the low-temperature phase. 3'4 The transformations may occur by a "single interface" or by "multiple interfaces."5'6 In the "single interface" transformation, the twinned product phase consisted of two twin orientations as shown in Fig. 1. In the multiple interface transformation the product phase contained "domains" each of which contained two twin orientations, Fig. 2. Deformation of specimens containing transformation twins was achieved by motion of the twin boundaries. Releasing the applied stress resulted in the displaced twin boundaries returning towards their initial positions. This "pseudo-elastic" behavior of the boundaries varied with time after the formation of the twin boundaries by the transformation.

Jan 1, 1961

By P. E. Rider, K. A. Gschneidner, O. D. McMasters

The solid solubilities for thirteen rare-earth metals in gold were determined by using the X-ray parametric method. Solubilities ranged from 0.1 at. pct for lanthanum in gold up to 8.8 at. pct for scandium in gold. The solubilities from lanthanum to gadolinium were very small and essentially constant, but a sharp increase occurred from gadolinium to scandium. The large solubilities for the heavy rare-earth metals were not expected because of the large size and electrochemical differences between rare-earth atoms and the gold atom. Contributions from first- and second-order elasticity theory plus an electronic contribution were found to reasonably account for a more favorable size factor. Electron transfer from the rare-earth metal to the gold Is thought to occur such that the resultant rare-earth and gold electronegativities are favorable for solid-solution formation. It was also found that this mutual adjustment of size and electronegutivity does not occur if the pure-metal size factors are greater than a critical value of 25 pet. The eutectic temperatures for ten systems were determined and these remained fairly constant at approximately 809 "C for the lighter lanthanide metal-gold systems until the Er-Au system was reached, at which Point the eutectic temperature successively increased reaching a maximum of 1040°C in the Sc-Au system. This rise was correlated to the size factor becoming more favorable for solid-solution formation at erbium. The valence state of ytterbium was found to change from two in the pure metal to three when ytterbium is dissolved in the gold matrix. RECENT results1 reported concerning the solubility of holmium in copper, silver, and gold, showed that the solubility of holmium in gold was quite large, 4.0 at. pct, compared with 1.6 in silver and 0.02 in copper. The small solubilities of holmium in silver and copper are quite reasonable in view of the large size difference (22.2 and 38.2 pct, respectively), large electronegativity difference (0.59 for both systems), and possible unfavorable valency factor (assuming one for silver and copper and three for holmium). The large solubility in gold, however, is unexpected because these same factors are also unfavorable for holmium and gold (22.5 pct size difference and 0.69 electronegativity difference), and because the light rare-earth metals, lanthanum, cerium, and praseodymium, have negligible solid solubilities in gold.2 In view of this unexpected behavior, it was felt that a study of the solid solubilities of most of the rare-earth metals in gold would be desirable to better understand the factors involved in the formation of solid solutions. Of the rare-earth metals added to gold in this study, only ytterbium is divalent in the pure metallic state (the other rare-earth metals are all trivalent) and many of its physical properties (such as the metallic radius, electronegativity, and so forth) are much different from those of the normal trivalent rare-earth metals.' The properties of ytterbium are such that one would expect solid-solution formation to be less favorable for ytterbium in gold than for any of the normal trivalent rare-earth metals. But chemically ytterbium is known to possess a stable trivalent state, and it is quite possible that ytterbium may alloy as a trivalent metal under certain conditions rather than as a divalent metal. Because of the dual valency nature and because so little is known about the alloying behavior of ytterbium, the gold-rich ytterbium-gold alloys are of special interest. EXPERIMENTAL PROCEDURE Materials. The gold used in this investigation had a purity of 99.99 pct with respect to nongaseous impurities. In general the rare-earth metals were prepared by reduction of the corresponding fluoride by calcium metal.3 The impurity contents of the metals used in this study are given in Table I. Preparation of Alloys. Two- or 3-g alloy samples were prepared by arc melting. The samples, with the exception of some of the Er-Au alloys, had weight losses of 0.5 pct or less. All alloy concentrations noted in this paper are nominal compositions. After arc melting, the alloys were wrapped in tantalum foil, sealed off in quartz tubing under a partial atmosphere of argon, homogenized for approximately 200 hr at 780°C, and then quenched in cold water. X-Ray Methods. The X-ray parametric method was used in determining the solubility of the rare-earth metals in gold. filings were sealed in small tantalum tubes by welding under a helium atmosphere. The tantalum tubes were then sealed in quartz tubing under a partial argon atmosphere, and annealed for times ranging from 1/2 to 3 hr (the length of time was inversely proportional to the an-

Jan 1, 1965

By L. H. Levenson, Charles S. Barrett

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By Charles S. Barrett, L. H. Levenson

Plastic flow in metal crystals and the changes in orientation resulting from it are generally understood to take place by the following fundamental mechanisms: (1) slip on crystallographic planes, (2) homogeneous crystal rotation resulting from the slip, (3) bending of the 1attice between the planes of slip, and, under certain circumstances, (4) twinning. This paper and a preceding one on iron subjected to uniaxial compression1 concern two additional processes that must now be added to this list: (5) the formation of deformation bands, and (6) the bending and rotation of these bands. The present investigation yields a new understanding and definiteness to the common terms so loosely used when speaking of cold-worked metals —('grain fragmentation," "elongated grains," and "deformation twins," "deformation bands," "etch bands," or "X-bands." Bands have been noted on the polished and etched surfaces of cold-worked metals by various investigators for more than 25 years, ‡ yet their nature and their significance have been so little understood that they are not treated in the most comprehensive modern texts on the deformation of crystals. The experiments in this series show that they are one of the fundamental processes in the deformation of metals, of importance in the development of preferred orientations, in work-hardening (since they have the effect of reducing the effective grain size and interfering with slip), and in the recrystallization process. The present experiments were performed on the same stock of material that was used in the earlier compression experiments1—hydrogen-purified mild steel in which the carbon content had been reduced to the limit detectable under the microscope and in which single crystals could be grown by a strain-anneal treatment.2

Jan 1, 1939

By C. S. Finney, John Mitchell

The introduction of ovens for the production of metallurgical coke is believed to be due to L. L. Norton who operated an iron foundry in the vicinity of Connellsville, Pa. Persuaded by his foreman, an English immigrant named Nickols from Durham, L. L. Norton put up a 12-ft square oven which produced coke in 1833. The coal used was taken from a local mine at Mounts Creek. The oven seems to have been used in conjunction with the customary method of coking in mounds. It was in the Connellsville district also, in 1841, that two carpenters, Provence McCormick and James Campbell, formed a partnership with John Taylor, a stone mason, for the manufacture and sale of oven coke. The task of the mason was to construct the ovens, while the carpenters were to build the arks by which the coke could be taken by water to the market at Cincinnati. The following account of the enterprise was given by McCormick: "James Campbell and myself heard in some way that I do not now recollect that the manufacturing of coke might be made a good business. Mr. John Taylor, a stone mason, who owned the farm on which the Fayette coke works now stand, and who was mining coal in a small way, was spoken to regarding our enterprise, and proposed a partnership-he to build the ovens and make the coke and Mr. Campbell and myself to build a boat and take the coke to Cincinnati, where we heard there was a good demand. This was in 1841. Mr. Taylor built two ovens. I think they were about 10 feet in diameter. My recollection is that the charge was 80 bushels. The ovens were built in the same style as those now used, but had no iron ring at the top to prevent the brick from falling in when filling the oven with coal, nor had we any iron frames at the mouth where the coke was drawn. The top and mouth had to be repaired when they fell in. In the spring of 1842 enough coke had been made to fill two boats 90 feet long-about 800 bushels each-and we took them to Cincinnati down the Youghiogheny, Monongahela, and Ohio, but when we got there we could not sell. Mr. Campbell, who went with the boats, lay at the landing some two or three weeks, retailing out one boatload and part of the other in small lots at about 8 cents a bushel. Miles Greenwood, a foundryman of that city, offered to take the balance if he would take a small patent flour mill at $125.00 hi pay, which Mr. Campbell did. He had it shipped here. We tried it, but it was no good, and we sold it to a man in the mountains for $30.00, and thus ended our coke business." So successful did the coke subsequently prove to be in use that the three partners were asked to deliver more. Evidently they had had enough of the coke business, however, for they refused to have anything more to do with it. Few ovens were built between 1841 and 1855, and it is reported that in the latter year, "there were only 26 coke ovens along the river above Pittsburgh". Successful coke makers of these years included Mordecai Cochran, Richard Brookius, and Colonel A. M. Hill. It was the use of coke in 1859 in the Clinton furnace erected by Graff, Bennett and Co. in a plant on West Carson Street, Pittsburgh, that brought the real beginning of the coke-iron era in America. Here the successful use of Connellsville coke as a blast-furnace fuel was demonstrated beyond all possible doubt, and from the year 1859 the coking industry expanded tremendously. The era of beehive coke ovens During the latter half of the nineteenth century and the early years of the twentieth, the major percentage of metallurgical coke produced in the United States came from beehive ovens. It was not until 1893 that the first battery of by-product ovens came

Jan 1, 1961

By J. O. Brittain, N. R. Adsit

A number of zinc bicrystal specimens with the grain boundary loaded in simple shear were plustically deformed in creep in a vacuum at 200°C and under an argon atmosphere at 350°C. The results indicated that the amount of grain boundary sliding at a given time was controlled by the slip in the grains and was proportional to the resolved shear stress on the slip plane. Curves of grain boundary sliding vs time were found to be cyclic with no regular periodicity. ALTHOUGH grain boundary sliding (G.B.S.) has been investigated in a number of different types of tests on various materials there is substantial disagreement on the interpretation of the various observations. Gifkins1 has presented a comprehensive review of the subject of G.B.S. and fracture. He reports that the activation energy for high-temperature creep is equal to that for volume self-diffusion and that pure metals show less tendency towards intercrystalline fracture than alloys. Pure metals show appreciably greater grain boundary migration than alloys, and both grain boundary migration and grain boundary sliding follow the same general trend in time as plastic deformation during creep.' While there have been a number of different mechanisms proposed to account for G.B.S., none of the models explains all the results. Since zinc has only one prominent slip system, it was hoped that experiments on G.B.S. in zinc bicrystals might enable us to separate the effect of grain boundary angle and the effect of matrix slip and thereby resolve at least one part of this complex phenomenon. EXPERIMENTAL PROCEDURE Bicrystals of pure zinc (99.99 pct) were grown by a Bridgeman technique in a furnace having a gradient of 20°C per in. The bicrystals were seeded to a desired orientation and grown in a split graphite mold which was 3/4 by 5/8 by 8 in. The mold was enclosed in a Pyrex tube and the tube was evacuated and then filled with a small amount of argon before it was placed in the furnace. The growth rates were 1/2 to I in. per hr for the bicrystals and 1/2 to 3 in. per hr for the single-crystal seeds. The longitudinal V notches served to hold the grain boundary in position during the growth process. A schematic rep- resentation of a specimen which had been cut with a jewelers saw from the bicrystals is shown in Fig. 1. All specimens of a series were cut from the same crystal, some of which were 7 in. in length. After specimen preparation the boundary was approximately 5/16 in. long and the V notches had a radius of 1/16 in. The boundaries were straight at a magnification of X100 with the exception of a few which had a gradual radius of curvature of greater than 3.2 in.-1. Laue back-reflection photograms were taken on the specimens to check the orientation of grains in the bicrystals. The method of relating the orientation of the two lattices is shown in Fig. 1, where 0 is the angle between normal to the boundary and the trace of the basal plane, is the angle in the boundary between the trace of the basal plane and a line parallel to the V notch, and x is the angle in the basal plane between the Burgers vector and the perpendicular to the grain boundary. After mechanical polishing the specimens were chemically polished.2 Subsequent to the polishing operation the specimens were encapsuled under a vacuum of better than 25 annealed at 340°C for 1 hr to remove the effects of this handling, and again chemically polished. Finally, fiduciary marks were scribed on the specimen using a micromanipulator. Creep tests, which were conducted in a modified Bausch apparatusS with the boundary loaded in simple shear, were run at a constant load (since the boundary area remained essentially constant this is approximately constant grain boundary stress). The temperature was controlled to ±1/4°C as measured on a semiprecision potentiometer with a calibrated thermocouple. The specimens were tested in a vacuum of better than 0.5 at 200°C and in purified argon at a pressure of 1/2 atm at 350°C. The op-

Jan 1, 1965

By C. H. Mathewson

EXCEPTING the joint sessions on gases in metals held during the day on Tuesday, the Institute of .Metals opened its activities with a division dinner at the Commodore on Tuesday evening, with Sam Tour, retiring chairman, presiding. W. M. Corse, secretary-treasurer, outlined the financial status of the division and stated the investment fund is becoming large enough so that in the near future it will be possible to pay all expenses of a foreign lecturer once in two years and not rely on an extended speaking tour to cover expenses. W. B. Price reported on his attendance at the Zurich, Switzerland, meeting of the International Society of Testing Materials and gave a graphic account of his visit to the Grand Salon, his meeting with Mussolini, and his audience with the Pope. Buffalo was announced as the place of the fall meeting, to be held during the week of Oct. 3.

Jan 1, 1932

By John G. Tate, George W. Nicolson, James L. Bruce

FOR more than 25 years modern mining has been carried on in the Island of Cyprus, Mediterranean Sea, by the Cyprus Mines Corp. of Los Angeles, Calif. The general features of these operations have been described.1 From 1935 to June 30, 1940, top slicing in the Mavrovouni mine produced in excess of 2,000,000 long tons. The rate for the last part of this period was approximately 50,000 tons per month. DESCRIPTION OF ORE BODIES The shape of the ore body now being top sliced in the Mavrovouni mine is an inclined irregular pyritic pipe or chimney of large dimensions, extending from unknown depths below the bottom level at elevation 250 ft below sea level, to the highest level at elevation 400 ft above sea level. The present surface above the ore body lies between 550 and 650 ft elevation. Undoubtedly the ore body extended to surface and was mined by the ancients by opencast and underground methods. The old pits were gradually filled up by erosion until now they show as slight depressions in the topography. The largest area of the ore body is at elevation 170 ft below sea level, where the horizontal section is almost elliptical, with a width of 600 ft and a length of 1000 ft. Below this elevation the shape of the ore body continues to be elliptical but with reduced dimensions. Above this elevation it rises flatly towards the south with a substantial depression in the upperside of the chimney and irregular ridges or wings rising on each side. It gradually grows smaller as it rises. The ore body is a pyritic replacement of andesitic extrusives which occur as flows and pillow lavas. With the exception of the upper portions of one or two small offshoots rising from the main ore body, all ore is completely surrounded by andesite. Most of the andesite lying above the ore body is covered by marl and clay sedimentaries of Miocene and later age. The Miocene is presumed to be older than the ore mineralization. That portion of the andesites which lies between the sedimentaries and the ore body has been broken by slumpage, and weathered, and iron-stained by the descending meteoric waters. It is a mass of crushed material that caves and follows downward readily as the top-slice stopes retreat. The main ore body is a heavy cupreous pyrites mass assaying on the average about 4.0 pct Cu; 48.0, S; and 42.0, Fe. In places the copper drops below 1.0 pct. On the borders of this heavy sulphide ore body lie disseminated cupreous pyrites ore deposits of large dimensions. Some portions of these appear to be closely related to the heavy sulphide ore, as the ratio of copper to pyrite is about the same. The greater part of the disseminated ore, most of which lies immediately to the east of the main ore body, contains less than 0.10 pct Cu and about 25.0 to 30.0 pct S. This probably can

Jan 1, 1947

By W. B. Price

AT the New York meeting of the American Institute of Mining and Metallurgical Engineers held in February, 1926, W. H. Bassett and J. C. Bradley presented a paper entitled "Exudations on Copper Castings."' The purpose of the present paper, as the title suggests, is to call attention to somewhat similar phenomena which the authors have encountered in brass and bronze. From a study of the examples given, a more-or-less speculative theory of "inverse segregation" is advanced. Protuberances on Admiralty Brass In the rolling mill of the Scovill Manufacturing Co., there have been found quite commonly bars of certain alloys which had a sort of shaggy roughness on the surface due to slight metallic protuberances. No special attention was paid to these until some bars were found on which these protuberances were heavy enough at the bottom of the bars to produce a blistered appearance. A sample of the protuberances was milled off the surface of the bar illustrated (Fig. la) and upon analysis was found to contain 66.66 per cent. copper, 4.02 per cent. tin and 0.03 per cent. lead, whereas the average composition of the bar was 70.21 per cent. copper, 1.21 per cent. tin, and 0.01 per cent. lead. A sample of the shaggy-rough protuberances at the very top of a bar was also analyzed and was found to contain 2.45 per cent. tin, indicating that it was probably of the same origin as the blistered areas. These results were not entirely unexpected for previous analyses of this alloy had revealed that the surface was richer in tin than the rest of the bar. This, of course, is contrary to what we would expect from a consideration of the equilibrium diagram and has been called "inverse segregation." Fig. 16 is a cross-section of a bar through the protuberances on the surface. It reveals that there is a decidedly different structure through the raised areas and seems to indicate that the bar originally solidified

Jan 1, 1927

Discussion -of the paper of I. N. KNAPP, presented at the New York meeting, February, 1915, and printed in Bulletin No. 96, December, 1914, pp. 2783 to 2793. A. C. LANE, Tufts College, Mass.-Is there any noticeable effect in drilling against salt water? Mr. Knapp says that the mud settles very quickly when brine is added-. What is the effect when you strike a strong salt water ill boring? I. N. KNAPP.-You are supposed to have enough mud pressure in your well to keep the saltwater out. I have drilled against what I knew to be 80 ft. head of water, and hot water too at 99.5°; this water did not show until the well was bailed and the mud pressure reduced. HENRY Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).-Mr. Knapp may be interested to learn that the use of mud in drilling through porous strata is much older than lie appears to be aware of. It has been used notably by Honigmann for boring shafts in Holland and in some of the adjoining portions of Germany. At the Oranien Nassau colliery, shafts about 12 ft. in diameter and 425 ft. deep were sunk in. this way-namely, by boring with a rotary borer, a thick mud puddle being pumped into the shaft, so as to maintain a pressure in the shaft greater than the hydrostatic pressure in the surrounding loose sands and thus keeping the sides of the shaft from collapsing. He will find references to this method in Das Abbohren von Schächten; Handbuch der Ingenieurwissenshaften, p. 134, also in the Transactions of the Institution of Mining Engineers, vol. xiii (1896-97), p. 155. The process appears to have been employed even before 1895, though I cannot give the exact date when it was first used.

Jan 5, 1915

By F. C. Bond, J. T. Wang

H. J. Kamack (E. I. du Pont de Nemours & Co., Inc., Wilmington, Del.)—Rittinger's law usually is stated to the following effect: "The work (or energy) consumed in particle size reduction is proportional to the new surface area produced." The law has been stated substantially in this way by Taggart20 Berry21 Dalla Valle22 Coghill and DeVaney,23 Richards and Locke," Gross,25 and many others, and, according to Gaudin,26 was originally expressed by Rittinger in the same form. Consequently there can be little doubt that this is the understanding of the law among most workers in the field of particle size reduction. Bond and Wang, however, express the law in the form "the useful work accomplished . . . ." (italics theirs). The distinction is critical, for in the form used by Bond and Wang the law becomes, as they themselves remark "merely a more or less arbitrary definition of useful work," while in its usual sense the law expresses a physical hypothesis which has been verified experimentally within certain limitations. Considering the way the law has been used, it might be stated more explicitly as follows: "In a given machine operating under a given set of constant operating conditions, the work consumed in the particle size reduction of a given material is proportional to the new surface area produced." Or, as Coghill and deVaney have said,27 "the (Rittinger) law holds only when the tests being compared are made under analogous conditions." There are occasions when the law transcends these limitations; for example, the surface area produced per unit energy consumption for a given material in a ball mill does not vary much over a fairly wide range of operating conditions. But by and large, the surface area production per unit energy consumption will vary with the operating conditions, the type of machine, and the material. The essence of Rittinger's law is that the surface area production per unit energy consumption is independent of the particle size, and this has been verified experimentally by numerous workers for numerous materials, within certain limits. An important limitation is that when one grinds to very small particle sizes, agglomerative forces may tend to interfere with size reduction so that the surface area increases less rapidly than Rittinger's law would predict. Within such limitations, Rittinger's law can be regarded as empirically established. The law has, however, certain theoretical implications, and it seems to be chiefly against these that Bond and Wang direct their criticism. Solids are believed to possess surface energy which is proportional to surface area. Thus, Rittinger's law implies a proportionality between surface energy produced and mechanical energy expended (for a particular material in a particular machine). It does not imply that all or most of the mechanical energy is transformed into surface energy; in fact it is known that most of the mechanical energy is transformed into heat. Bond and Wang assert that most of this heat arises from the damping of elastic vibrations of stressed particles. This may possibly be true for crushing (with which they are chiefly concerned), although in grinding it is probable that much of the heat arises from friction between particles. However, the fact that the surface energy is small compared to the heat energy does not invalidate Rittinger's law, which implies merely that they are proportional. The authors also criticize Rittinger's law on the grounds that "this theory cannot be justified mathematically, since work is the product of force times distance, and the distance factor is ignored," and "energy input must be the product of force times distance, and the Rittinger theory completely ignores large variations in the distance (strain dimension or deformation) throughout which a force must act to produce breakage of different materials." However, the quantities force and distance as such are irrelevant to Rittinger's law, which considers energy input as an integral quantity. The fact that different materials require different forces and strains (hence, different amounts of energy) to break them is incontrovertible but again is irrelevant to Rittinger's law, which, as mentioned before, applies -only to a single material. Even in theory, it would not be expected that the surface area produced per unit energy consumption would be the same for different materials, because the surface energy per unit area is presumably specific to each material. Bond and Wang advance another argument of a

Jan 1, 1952

By P. Rama Rao, D. H. Sastry, T. R. Anantharaman

Deformation (a) and twin (a') stacking-fault densities in cold - wor ked filings of fcc silver alloys containing 2, 4, and 6 wt pct Sb have been estimated from Debye-Scherrer peak shifts and asymmetries, respectively. Evidence has been obtained for a possible strain-induced transformation in a two-phase alloy containing 9.0 zut pct Sb. Using Fourier analysis of X-ray line profiles, the effective particle sizes and root mean square strains have been determined for the three fcc alloys in the cold-worked condition. The values of the compound fault probability 0.5a + a') evaluated from peak shifts and asymmetries are in reasonable apeement with those derived from peak broadening. COLD work of fcc metals may produce both deformation and twin (also called growth) stacking faults, which can be detected and quantitatively estimated by X-ray diffraction techniques.' In addition to peak broadening, deformation faults produce a shift in peak positions and twin faults an asymmetry of the Debye-Scherrer reflections. Besides stacking faults, a reduction in the size of coherently diffracting domains and distortion within these also broaden the powder reflections of deformed fcc metals and alloys. Fourier analysis' of peak shapes provides quantitative infor- mation about the effective domain sizes, lattice strains, and also the compound fault probability (1.5a + a'), where a and a' represent deformation-and growth-fault density, respectively. The Paterson method2 for determination of a from peak shifts, the warren3 or wagner4 method for evaluation of a' from peak asymmetries, and the Fourier analysis for quantitative estimates of all the contributory causes of peak broadening have, in the course of the last decade, been extensively applied to obtain data for a number of deformed fcc metals and alloys. One of the useful results of earlier measurements of a in several solid solutions is a correlation between a and the solute valence as well as electron concentration per atom (p) in alloy systems based on a particular solvent. The work of Smallman and westmacott5 on Cu-Zn, Cu-A1, and Cu-Sn, of Foley, Cahn, and ~aynor' on Cu-Si and Cu-Ge, and of Rama Rao and Anantharaman7 on Cu-Si and Cu-Sb has revealed a common trend in the increase of a with p and also a with valency of the solute. Cahn and Davies' and Ad-ler and wagnerg have observed similar trends for silver alloys containing cadmium, indium, and tin. Data on a for silver alloys with a pentavalent solute element are not, however, available. It is primarily to fill this need that the present investigation on Ag-Sb alloys was undertaken. Utilizing the Patersonand Warren methods, values of a and a', respectively, have been determined in three silver alloys containing 2, 4, and 6 wt pct Sb. By Fourier analysis of the broadening of Debye-Scherrer peaks, effective particle sizes, lattice strains, and the compound fault probability (1.5a +a') have also been evaluated.

Jan 1, 1967

By executive order of the President, dated June 25, 1918, the investigation of matters relating to gas warfare, which had been initiated by the Director of the U. S. Bureau of Mines early in 1917, and had been continuously maintained and improved since, that time, was transferred to the recently created Division of Gas Warfare of the War Department. On the occasion of this transfer, both the President and the Secretary of War took occasion to speak most highly of the efficient service that had been rendered by the Bureau of Mines. It gives us great pleasure to reproduce here a letter from the President and from the Secretary of War, bearing on this subject and also to append a brief review of the work of the Bureau of Mines, prepared by its Director, Mr. Van H. Manning. The White House, Washington. June 26, 1918. MY DEAR MR. MANNING: I have had before me for some days the-question presented by the Secretary of War involving the transfer of the chemical section established by you at the American University from the Bureau of Mines to the newly organized Division-of Gas Warfare in which the War Department is now concentrating all the various facilities for offensive and defensive gas operations. I am satisfied that a more efficient organization can he effected by having these various activities under one direction and control, and my hesitation about acting in the matter has grown only out of a reluctance to take away from the Bureau of Mines a piece of work which thus far it has so effectively performed. The Secretary of War has assured me of his own recognition of the splendid work you have been able to do, and I am taking the liberty of enclosing a letter which I have received from him, in order that you may-see how fully the War Department recognizes the value of the services. I am to-day signing the order directing the transfer. I want, however, to express to you my own-appreciation of the fine and helpful piece of work which you-have-done, and to. say that this sort of team work by the bureaus outside of the direct war-making agency is one of the cheering and gratifying evidences of the way our official forces are inspired by the presence of a great national task. Cordially yours, Dr. Van. H. Manning, WOODROW WILSON. Chief, Bureau of Mines, Department of the Interior. War Department, Washington, June 25, 1918. MY DEAR MR. PRESIDENT: In connection with the proposed transfer of the chemical section at. American University from the Bureau of Mines to the newly constituted and consolidated Gas Service of the War Department, which you are considering, I am specially concerned to have you know how much the War Department appreciates the splendid services which have been rendered to the country and to the Army by the Department of the Interior, and especially by the Bureau of Mines under the direction of Dr. Manning. In the early days of preparation and organization, Dr. Manning's contact with scientific men throughout the country was indispensably valuable. He was able to summon from the universities and the technical laboratories of the country men of the highest quality and to inspire them with enthusiastic zeal in attacking new and difficult problems which had to be solved with the utmost speed. I do not see how the work could have been better done than he did it, and the present suggestion that the section now pass under the direction and control of the War Department grows out of the fact that the whole subject of gas warfare has assumed a fresh pressure and intensity, and the director of it must have the widest control so as to be able to use the resources at his command in the most effective way possible. The proposal does not involve the disruption of the fine group of scientific men Dr. Manning has brought together, but merely their transfer to General Sibert's direction. Respectfully yours, NEWTON D. BAKER.

Jan 9, 1918

By R. L. Slobod, B. H. Caudle, R. A. Erickson

In predicting the sweepout pattern efficiency to be expected in a .secondary recovery operation, the reservoir engineer is often confronted with a situation in which part of the producing formation lies between the last row of wells and the reservoir boundary. To date, there has been little or no reference in the literalure to sweepout pattern efficiencies in such areas. This paper presents the results, of a laboratory study in which the area contacted around the edge of a reservoir injected in a five-spot pattern was determined. The X-ray shadowgraph technique was used in this study. It was found that surprisingly large portions of the reservoir area lying outside the well network are conracted by the injected fluid before, abndonment conditions are reached. In fact, it can he said that at least 00 per cent of the circa lying outside the last row of wells and within a distance of one well spacing of these wells will ultimately be contacted by the injected fluid in the case of most water floods. Frorn the results given in this paper, it is possible to estitilate not only the extent to which encroachment into these areas will occur but also the injection volume necessary to produce the wells to abnndonment conditions. INTRODUCTION While considerable work has hern done in recent years1.?.'.''.' evaluating the fraction of the reservoir contacted as a function of the mobility ratio for several different well patterns, there has been practically no mention of what happens to the oil in that portion of the reservoir which lies between the last row of wells and the reservoir boundary. In fact, the assumption is generally made that little or no recovery can he expected From this area. This assumption is incorrect and in many cases will lead to seriouq errors in calculating reservoir performance. The fraction of the area outside the regular well pattern contacted in a five-spot injection system has been studied using the X-ray technique5 to follow the progress of actual floods in porous models of reservoir elemental areas. In this paper, the method for carrying out such a study and the results showing the fraction of the area in question swept as a function of mobility ratio and the produced fluids are presented. THE REPRESENTATION OF A RESERVOIR BY ITS ELEMENTAL AREAS She portion of the reservoir lying between the edge of a reservoir and a line connecting the outermost wells may be roughly designated as the part of the reservoir outside the regular well pattern. An example of such an area is shown as the shaded portion in Fig. 1. The case of a square reservoir utilizing a five-spot injection program and with one full well spacing between the outermost wells and the boundary (Fig. 1) was selected as the single example which would provide the most insight into

Jan 1, 1956

By H. C. Chao, Y. E. Smith, L. H. Van Vlack

ThE phase relationships for the MnO-MnS system have been investigated only in the eutectic region. wentrupl reported a eutectic at 1280°C (2345°F) with approximately 50 wt pct of each component, as based on the earlier work of Andrew, Maddocks, and Fowler.2 More recently silverman3 corrected these figures to 2275° ±10°F (1246°C) with 63 wt pct MnS and 37 pct MnO. Neither Wentrup nor Silverman investigated the solid-solution limits in this system. However, Wentrup did suggest with his phase diagram sketch that the maximum solubility of MnS in MnO is 10 wt pct, and the solubility of MnO in MnS is nearer 20 wt pct, Fig. 1. These figures have been utilized in subsequent publications without further verification.4 There had been evidence found in this laboratory that the above solid-solution figures were high. An investigation was therefore conducted using the following procedure. Samples containing MnO and MnS were contained in platinum foil, heated just above the eutectic temperature in a purified nitrogen at- mosphere, and quenched into distilled water. The MnO had been prepared by calcining reagent grade MnCO3 in nitrogen at 1400°C. Only MnO was detected in subsequent X-ray diffraction analyses. The MnS had been prepared by sulfur deoxidation of reagent grade MnSO4 according to the reaction: MnSO4 + S2 ? MnS + 2SO2 The details of the sulfide preparation procedure, which utilized atmospheric sulfur pressures at 950°C, are discussed elsewhere.5 The sulfur content of the sulfide was determined to be 36.8 * 0.2 pct, which matches the stoichiometric value of 36.9 pct. No evidence of either MnO or MnSO4 was detected microscopically or by X-ray diffraction. The single-phase combinations of MnO and MnS at the eutectic temperature indicate the limit of solid solution as shown in Fig. 2(a) and (c), and the revised phase diagram is shown in Fig. 2(d). The melting temperature for MnO is that provided by Glasser.6 The eutectic temperature of 1232° ± 5°C and eutectic composition of 64 wt pct MnS are in close agreement with Silverman's correction of Wentrup's work. The maximum solubility of MnO in MnS was determined to be 1.7 ± 0.2 wt pct. The maximum solubility of MnS in MnO was determined to be 1.8 ± 0.2 wt pct. These figures represent the lower limit for the presence of liquid at 1260°C and are significantly lower than the earlier estimated solid-solution figures. The authors wish to acknowledge the support of U.S. Steel's Edgar C. Bain Laboratory for Fundamental Research. The comments and critical suggestions of Drs. A. S. Keh, R. Rickett, and R. B. Snow are appreciated.

Jan 1, 1963

By Nicholas J. Grant, H. C. Chang

EMPHASIS on the importance of grain boundary sliding as a mode of deformation at elevated temperatures has been presented elsewhere.' The extent to which boundary sliding occurs under certain creep conditions has been determined for high purity aluminum2,3 and aluminum alloys.' In general, boundary deformation extends quite far into the adjoining grains, resulting in a rather wide band of deformation along the grain boundaries. This has led some investigators to doubt that grain boundary sliding consists of shearing along the boundary surface; it has been contended instead that boundary sliding is a result of concentrated slip in the neighborhood of the deformed grain boundaries."' The purpose of this note is to present evidence that grain boundary sliding takes place by a bulk shear process. gh purity polycrystalline aluminum, wherever and whenever there is grain boundary sliding, boundary migration and concentrated deformation along both sides of the deformed boundary are associated with it. Therefore, it has been rather difficult to obtain unambiguous evidence of boundary sliding. On the other hand, it would be expected in certain alloys of aluminum, when tested under particular conditions. that the severity of the interfering effects of boundary migration and concentrated deformation along the deformed boundary might be reduced. Current research in this laboratory' shows that a 20 pct Zn-A1 solid solution alloy fractures in an intercrystalline manner during creep at 500°F with a small total elongation of not more than about 14 pct, and that it does so with extremely limited grain boundary migration. Accordingly, this alloy was chosen for the present study. The experimental procedure was similar to that used in previous work and has been presented elsewhere.' Two parallel flat surfaces were milled from a round specimen. The gage portion of the specimen was 1 in. x .09 in. x .17 in. The specimens, which were annealed at 1030°F for 24 hr, showed two to four grains across the width of the test bar. The specimens were subjected to creep at 500°F at stresses of 2000 to 5000 psi. The rupture times were from 10 sec to 3 hr. Appreciable boundary sliding occurred in all the tests. A typical example of boundary sliding is shown in Fig. 1. (The tension axis is vertical in the micrographs.) Sliding has taken place along the boundary between grains A and B unaccompanied by important boundary migration. The sharpness of the offset at the triple point can be clearly seen in grain C. As a result of sliding along the boundary between grains A and B, a new boundary surface between grains A and C was created. The offset at the triple point is about 0.07 mm. This boundary sliding is accompanied by the formation of rather sharp kinking bands and, of course, slip on several slip systems in grain C. This type of deformation has been referred to as fold formation' in previous work with high purity aluminum.

Jan 1, 1957

By Leonard Bernstein, Harry Bartholomew

MANY of the properties of metals and alloys are structure dependent. Not the least of these is the grain structure. For example, in producing alloy bonds between silicon or germanium and gold-alloy foil at temperatures above their eutectics (which are, respectively, at 370" and 356°C) but below the melting points of the individual constituents, it was found that wetting was more complete with a fine-grain structure than with a coarse-grain structure. In cases where the assemblies were held together for long periods of time at elevated temperatures, wetting was not as critically dependent on the grain structure as was the case for shorter periods of time. When liquid phase forms, it first forms in the grain boundaries due to the fact that most of the impurities are concentrated at the grain boundaries and that most impurities tend to lower the melting point of the gold alloy somewhat. In addition, grain boundaries are at high-surface free-energy levels and are thus in a more favorable condition to initiate good wetting. A fine-grain structure will have more grain boundaries per unit area than coarse-grain structure thereby making wetting somewhat easier. To make the grain structure of an alloy sys- tem visible, a satisfactory method for differentiating between the different grains of which the system is composed must be employed. For the alloy bonding system previously described, the grain structure on the foil surface is of primary interest. Conventionally used etchants for the gold-alloy system will not adequately delineate grain boundaries in their structures. For this reason an alternate method is proposed for those cases where such a determination is necessary. Foil between 0.0005 and 0.005 in. thick has been used in this determination. The equipment used in this investigation was described in a previous publication.' Essentially, it employs a resistance-type filament which can be heated up very rapidly and cooled very rapidly. A thin refractory material is placed on top of the heating element. This refractory material may be molybdenum, tantalum, tungsten, or even ceramic but its thickness should be less than 0.010 in. to minimize the temperature gradient across it. The gold-alloy foil is placed on top of this refractory material. The temperature of the heating filament is raised to 900°C and cooled down to below 100°C in 5 to 10 sec. During this cycle, the foil can be observed to plastically deform due to its own weight. With no further chemical etching, this assembly is then viewed under a standard metallurgical microscope and the grain size measured. Fig. 1 is a Au-1 pct Sb alloy at 400X magnification and Fig. 2 is a Au-1 pct Ga alloy at 130X. This technique has proved to be an adequate means for controlling processing conditions in producing large quantities of gold alloy foil.

Jan 1, 1963

By Ronald C. Koo

THE effect of grain size on the mechanical properties of the bcc metals has been a subject of intensive theoretical and experimental study.'-l5 Quantitative relationships have been established experimentally between yield stress and grain size and between the ductile-brittle transition temperature and grain size in a number of metals.6"15 Much significance has therefore been attached theoretically to the grain size dependence. In all these experiments, different grain sizes were always achieved by annealing specimens at various temperatures. The implicit assumption was that any change in the dislocation substructure or in the distribution of impurities which might occur simultaneously with the production of various grain sizes had only a negligible effect on the mechanical properties. The validity of this assumption, however, is questionable. transformation in iron-nickel alloys is actually an extraneous phenomenon due to inadvertent compositional changes in the martensite if the heating rate is not sufficiently rapid. This complication can be avoided by up-quenching for the reversal treatment,5 and then the stabilization does not appear. Clearly, the lattice imperfections and strengthening produced by the reverse transformation are not responsible for the marked stabilization which has been observed by other investigators in these alloys. Data will be presented in this note to show that, at least in recrystallized tungsten of commercial purity, the difference in the ductile-brittle transition temperature of specimens annealed at various temperatures is more a result of a variation in the distribution of impurities rather than of the difference in grain size produced by the anneal. Ductile-brittle transition temperatures in tension were determined on powder-metallurgy tungsten specimens recrystallized at various temperatures. Tensile specimens having a gage length of 1.50 in. and gage diam of 0.18 in. were recrystallized at 1450°, 2000°, 2350°, 2550°, 2750°, or 2800" for 30 min in a vacuum furnace at a pressure of 1 x 10"5 mm of Hg and then tested at a constant extension rate of 8 x 10 per sec in an argon atmosphere from 100" to 800". Typical quantitative analyses of impurities are given in the Table. These results show that, within the precision of the analyses, see Table, annealing did not result in any detectable change in the impurity contents of the specimens, nor was there any detectable difference in purity between specimens having large differences in grain size annealed at the same temperatures . The results of the tensile tests yielded three distinct ductile-brittle transition curves approximately 225' apart. As shown in Fig. 1, data of specimens annealed at 1450°C and those of specimens annealed at 2000°C (O) fell on Curve A. Data of specimens annealed at 2350" and 2550°C fell on Curve B, and those of specimens annealed at 2750" and 2800°C fell on Curve C. The decrease in ductility with increase in annealing temperature became so pronounced that one third of the specimens annealed at 2750" and two thirds of the specimens

Jan 1, 1963