Search Documents

By Leo P. Tarasov

Magnetic torque studies of ferromagnetic single crystals have been carried out in a number of laboratories during the last decade&apos;s2 and some work has been reported on polycrystalline material showing preferred orientation. Goss3 used the method extensively in developing electrical sheet with desirable magnetic properties, but he used it as a control rather than as a means of studying the texture. Bozorth4 made a quantitative correlation of a torque curve he obtained from some cold-rolled iron with the texture as determined from X-rays, but did not extend his studies beyond the one specimen. Other studies, which have been reported from time to time2,5 have also been incomplete in the sense that no effort was made to study a whole series of samples, differing only in degree of cold reduction or in the annealing temperature, in order to ascertain the effect of such treatments on the texture as revealed by torque measurements. It is the purpose of this investigation to make such a study, mainly in order to see how useful the method can be made when used under favorable circumstances and to find what kind of a correlation can be expected between magnetic and X-ray studies of texture. Before proceeding further, it is desirable to say a little about single crystals, so as to make clear the concepts involved in magnetic torque measurements. Magnetic Torque Method It is fairly well known nowadays that single crystals of ferromagnetic substances have directions of easy magnetization and of hard magnetization. In Fig. 1 are reproduced typical magnetization curves for a single crystal of iron, which show that in a < 100 > direction saturation occurs at low fields compared to those required to saturate the same crystal in a <110> or a <111> direction. (The magnetization intensity I is defined by the equation B = H + 4pI.) At fields high enough to

Jan 1, 1939

The industrial might of the Bowen Basin is primarily the result of Utah Development Co.&apos;s work- which has opened up the Blackwater, Goonyella, Peak Downs, and Saraji mines; built the Hay Point port; and is now developing the Norwich Park mine.

Jan 1, 1977

By I. Cornet

With the greatly expanding use of magnesium during the war, it appeared necessary to the War Metallurgy Committee that the notch sensitivity of magnesium alloy extrusions be further investigated and the influence of various factors upon notch sensitivity be noted. Accordingly, the National Defense Research Committee of the Office of Scientific Research and Development placed a research contract with the University of California, supervised by the War Metallurgy Committee. The work discussed herein was done under "Restricted" Project NRC-21, reported in Dec. 1943~; it has been released for publica-tion by the O.S.R.D. Scope of the Investigation The notch sensitivity of various magnesium alloy extrusions was determined under axial tension, and also under several conditions of nonaxial tension. Hardness, grain size and other metallographic features were observed; stress-strain data were obtained, and the chemical compositions of the alloys were determined, in order to correlate these quantities with thc notch sensitivity. Notch sensitivity under axial tensile load was determined for a few specimens which had been cold worked to various degrees by tensile prestraining. Magnesium alloy extrusions studied included Dowmetal 0, X, J, and A(. For comparison, extrusions of aluminum alloy 24s-T, cast bars of aluminum alloy 122-T2, and cast bars of magnesium alloy C were also tested. The specified chemical composition of these alloys is given in Table I. All bars tested were within specification limits of composition. Investigation of thc tensile notch sensitivity of various magnesium alloy extrusions, under conditions of axial and eccentric load, showed little or no correlation with stress-strain or other conventional data. Since the many uncontrolled variables present might mask significant relationships, one alloy was selected for intensive study. Magnesium 0 alloy extrusions were subjected to experimental heat treatments, and the ,Changing hardness, tensile strength, microstructure, and notch sensitivity observed. Experimental Techniques and Procedures Tensile Testing Bars used for axial loading were machined with % in.- and with 34-in. minimum diam1 and included specimens with 60" V notches (Fig I and 2). Each V-notched specimen was roughed out carefully and then finished with a honed tool. These Y-notched bars were sampled frequently, sectioned, polished, and examined at 500 X magnification to control

Jan 1, 1949

By R. J. Teitel

FOUR or five years ago an investigation was initiated to study and develop basic information on llquid metal fuels for future power nuclear reactors. The objective was to find fluid forms of uranium (solutions or dispersions) in low melting alloys. A summary of the different fuels was presented in a recent article by Teitel, Gurinsky, and Bryner.&apos; The combination of uranium and bismuth, with its low thermal neutron cross section and low melting point, is of basic interest to the development of these fuels. Most of the previous effort on the U-Bi phase diagram was done under security regulation. Ahmann and Baldwin&apos; reported their findings on the U-Bi system in 1945. Their results indicated that the phase diagram had at least two compounds and possibly one more. UBi, and UBi were established by chemical analyses of residues after high temperature centrifugation of alloys. UBi, decomposed peritectically at1980°C and there were signs of another reaction above that. UBi melted at a very high temperature, and there were also signs of a monotectic at high temperatures in high uranium alloys. The solubility of uranium in liquid bismuth has received attention by three groups of authors: Bareis,X ayes and Gordon,&apos; and Ahmann and Baldwin.&apos; The latest and most widely accepted data is that of Bareis, and it is included in Fig. 1 along with new data at higher temperatures. Brewer et al." and Ferro"&apos;&apos; have used X-ray diffraction to determine the number and crystal structure of the compounds. Brewer identified the structure of UBi to be a simple NaCl cubic structure having a cell edge of 6.364A. The density of the compound was calculated to be 11.52 g per cu cm. Two other unindexed patterns were presented as possibly belonging to two other compounds. Ferro agreed with Brewer on the crystal structure of UBi and identified the structure of UBi, and U,Bi,. The intermetallic compound UBi, has a tetragonal cell with a = 4.445A and c = 8.908A. The density of the compound was determined and the number of atoms per cell (six atoms) was calculated. The X-ray density reported was 12.35 g per cu cm. The compound UsBir was treated in a similar way and it was reported to have a cubic structure 9.35A on an edge and to contain 28 atoms per cell. The density was given as 12.59 g per cu cm. Teitel reported that there was a compound UaBi, and no UBi, compound. (The difference in the compositions is 3.3 pct U.) This conclusion was based upon the extrapolation of some 20 tie lines in the

Jan 1, 1958

By F. M. Lewis, J. F. Myers

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By J. F. Myers, F. M. Lewis

The paper reports the development of a large, slow speed ball mill closed circuited with a hvdro-scillator. This increased grinding efficiency 28 pct over conventional units. AS the title indicates, this is a progress report for the first year of experimental operation of a relatively large diameter, slow speed ball mill with 1-in. balls, with and without various classifiers, and including a hydroscillator. Several years ago the authors came to the conclusion that if any further progress were to be made in our flotation process, an understanding of the chemical and physical reactions and the control thereof, in the grinding circuit, was essential. It may be stated, at this point, that the preparation of a correct feed for the flotation process is still the number one objective of our grinding studies. This progress report deals with grinding "per se," and not with the chemical and physical reactions as the result of grinding. Prior to this time we had taken the naive position, that since grinding had been practiced by the industry for some fifty years or more, it had been well exploited and developed by a host of investigators. Consequently, we had given the matter only superficial attention. At the start of our study, we were aware of the fact that some difference in opinion existed, but we were not prepared for the controversial evidence that developed nor for the extent to which the experts differed in their viewpoints. There seemed nothing else to do but to tour the continent and decide for ourselves what was right and what was wrong, read all the published literature and visit with anyone who had ideas about the matter. This we did over the next few ensuing years. Since our study has met with some measure of success, we report, herewith, these data that ultimately they may be of help to other investigators. In 1944 it became necessary to increase our grinding capacity and at the same time to grind the sulphide portion a little finer. This provided the impetus to put our ideas into effect. As has been previously described, our grinding flowsheet at that time consisted of a 6x12 rod mill, followed by two 5x10 ft, and one 6x12 ft trunnion overflow ball mills, with conventional rake classifiers. Naturally, we first considered all the possibilities of altering or adding to the existing equipment. It became evident that if any appreciable increase in grinding efficiency could be obtained, it would pay to scrap the existing small mills and classifiers and install one big mill with adequate classification. Trying to determine just how much more efficient a big mill could be, in which were incorporated all

Jan 1, 1951

By Henry Wurtz

HERACLITUS, a sage of antiquity, called the dark philosopher, who refused a throne, preferring a hermit&apos;s cell, propounded, twenty-four centuries since, the maxim : [ ] War (or strife) engenders all things. This, though probably intended by Heraclitus to apply especially to the internal forces of nature, is often said, with equal reason, of the affairs of men. Controversial strife, whether fortunately or unfortunately, is a crucible through which all new discoveries in science, and all technical applications of science must pass-a test which they must all endure before they can become so vitalized as to germinate, so to speak, take root in the human mind, grow tip, and overspread the earth. The greater the number and the power of the elements arrayed against such a growth, and of the influences hostile thereto, the greater should be the inherent vitality of the germ, the more strenuous, skilful, and persistent its cultivators and upholders. During the decade last past we have had, in spite of the severe stringency of the times, an active growth of this kind in progress, whose prospective importance it would now be difficult to overrate. This is the movement which has for its motive the idea that, generally speaking, fuel should be gaseous in form, and which has for its goal the introduction into general public use of gaseous products, made by cheap and rapid processes and on a gigantic scale, distributed throughout our cities and towns in distribution-systems which shall be proportionately gigantic, and sold at prices which will bring such fuel within the means of the poorest householders. Personally, for ten years past, the writer has never failed, on occasions public or private, to urge his belief that the realization of this idea, deemed by him a certainty of the future, will bring about

Jan 1, 1880

By J. J. Kanter

The choice of a nonferrous metal or alloy for a given Application is frequently predicated upon a consideration of properties other than merely the capacity to withstand stress. When ability to withstand stress is the dominant engineering requisite of the material to be used, economic considerations seldom lead to the choice of nonferrous metals and alloys. In most instances where a nonferrous metal is used it is because of some special quality of either corrosion resistance, electrical properties, thermal properties, antifriction, or fabrication advantage that commends its application. The mechanical properties, as a rule, present an incidental engineering consideration entirely secondary to the special quality deciding its use. Indeed, great ingenuity has often been exhibited by engineers and metallurgists in overcoming the mechanical shortcomings of a nonferrous base material. in order to take advantage of some outstanding property. . With this thought in mind, we might better appreciate some of the problems in stress design. encountered with nonferrous metals and alloys pertinent to a symposium on their creep characteristics. Our considerations must necessarily be far from complete because of the broad range of materials in the nonferrous category for which creep properties assume a technical interest. Creep deformation of these metals can be subject for study at temperatures ranging from ambient to incandescent, depending upon which one is under consideration. Whereas the steel metallurgist thinks of creep as an essentially high-temperature engineering consideration, the same is not necessarily true in the field at hand. The diversity of the creep problems in the nonferrous field is perhaps accountable to some extent for its virginity as a symposium subject. Each research has necessarily been sponsored by some organization or group interested either in promoting the use of a certain nonferrous base or in obtaining data toward the solution of a mechanical difficulty encountered in applying a material indispensable for its special attributes. Perhaps as many techniques of creep testing have been used as there are base metals implied under "nonferrous." Some of the creep problems that have occasioned researches are associated with steam-pressure vessels such as tubes, drums, castings, and forgings of copper-base and nickel-base alloys, cable sheathings of lead and lead-base alloys, electrical transmission lines of copper and aluminum, engine parts die-cast from alloys based on zinc, aluminum, copper— soldered and brazed joints-—as well as numerous duties at extremely high temperatures met with alloys based on cobalt, nickel, tungsten, molybdenum, platinum, and other precious or semiprecious metals. Postwar technology will have the benefit of much creep research on nonferrous metals, which for reasons of security cannot be discussed on this occasion. Suitability OF Metals As already intimated, the bulk of the constructional metal that ordinarily is

Jan 1, 1945

By Paul M. Tyler

DOES mining pay? Inasmuch as the whining of minerals from Nature is one of the world&apos;s principal sources of new wealth, this question is of general economic interest but it is obviously of even more vital concern to investors and those engaged in mining. In a previous article on "Wage Costs in the Mineral Industries,&apos; published in the November issue, I attempted to show that wages paid workers on the job accounted for, roughly, 50 per cent of the mine dollar. Salaries normally range over 5 per cent - lower for large metal mines but higher in stone quarries and minor nonmetallic min. in, industries. Purchases of supplies, materials. fuel, and power generally aggregate within the range of 15 to 25 per cent of total receipts, with the average well under 20 per cent. The total of all such specified expenditures which may he loosely described as

Jan 1, 1934

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By K. E. Gray, M. S. Seth

Equations of elasticity for transversely isotropic, axisymmetric, homogeneous, porous media exhibiting pore fluid pressure were formulated. Using an analogy between thermal and porous body stresses, it was shown that the solution for a transversely isotropic porous body may be obtained by incorporating body forces and the stresses due to a boundary load into the corresponding solution for the thermal stress problem. Equations of elasticity ad the thermal analogy method were used to determine transient horizontal, tangential, and vertical stresses and radial displacement in a semi-infinite cylindrical region when either a constant pressure or a constant rate of flow is maintained at the wellbore. The vertical and tangential displacements are zero from the conditions of the problem. A numerical analysis was made of the solutions obtained by using a digital computer to determine the relative influence of each system variable. Considering rock as a porous body with internal fluid pressure generally gives results significantly different than considering the rock to be nonporous; the directional character of rocks leads to significant differences as compared to results based upon the common assumption of isotropy. Stress gradients are high near the wellbore but die out away from the well. Radial stresses are compressive or neutral, whereas tangential stresses are tensile, neutral or compressive, depending upon the boundary conditions and physical properties of the system Vertical stresses are compressive for an unbounded system. For constant wellbore injection rate, the vertical stress is proportional to the rate of fluid injection and decreases with time, whereas the radial and tangential stresses increase with time. At a given location, the radial displacement generally is very dependent upon time. INTRODUCTION A realistic appraisal of the state of stress in subsurface rock formations would be of considerable interest and use to the petroleum industry. For example, knowing the state of stress in proximity to a wellbore would be of fundamental importance in designing a fracturing operation or, more important, of clearly understanding the conditions necessary to produce rock failure of desired dimensions and geometry. Understanding conditions necessary for rock failure at the wellbore would also be of utility in a preventive sense. For example, borehole stability is an important consideration for many rock formations, and knowledge of the stress state at and near the wellbore under conditions of substantial pressure gradient due to fluid flow would be of great value. When fluid flows through a porous body which is initially at some uniform stress level, the following forces generate stresses at any point in the body. (1) Forces due to nonuniform pressure distribution. With increasing pressure the elements of a body are compressed. Such compression cannot proceed freely in a continuum when the pressure is not uniform throughout, and thus, stresses due to flow of fluid are set up. (2) Pore fluid pressure. This gives rise to normal stresses whose value at any point is the product of areal porosity and the fluid pressure. Although the fluid exerts uniform pressure, the stresses it creates in an anisotropic body may not be the same in all directions since the areal porosity in an anisotropic porous body is a direction-dependent quantity. This consideration leads to the concept of directional porosity. (3) Body Forces. The flow of the moving fluid imparts a force to the rock matrix, the magnitude of which depends upon the pressure

Jan 1, 1969

By B. Post, F. W. Glaser

Three borides of zirconium have been reported: ZrB,l ZrB2,2,3 and ZrB12, 4 The phase relationships, ranges of stability, and some physical properties of these compounds are described. THE zirconium borides differ considerably from one another, particularly with respect to their relative stabilities at high temperatures in the presence of carbon.4,5 ZrB2 is extremelv stable at all temperatures (to the melting point) in contact with carbon. Both ZrB and ZrB12 tend to decompose at elevated temperatures when carbon is present in excess of about 0.5 pct. ZrB forms ZrB2 and ZrC, and ZrB12 decomposes to form ZrB2 and a boron-carbide phase. In the ZrB12 preparation, boron present in excess of that needed to form ZrB2 reacts with carbon, if present, to form carbides, in preference to forming the higher boride. Similar instability of borides, other than diborides of the transition metals of the 4th and 5th groups of the periodic table, has been reported.5,6 special precautions had, therefore, to be taken to minimize carbon contamination in the preparation of ZrB and ZrB12. Reactions below 1400°C were carried out by heating powdered mixtures of zirconium hydride and boron in quartz tubes in a hydrogen atmosphere. For temperatures above 1400°C, reactions were carried out in graphite molds. Carbon contamination from the molds was minimized by employing extremely rapid heating rates to reduce carbon diffusion into the body of the specimen, and by subsequent "shaving" of sample surfaces that had been in contact with the graphite dies. A heating rate of about 2000°C per min was obtained by heating the dies (by direct conduction), using a current of 40,000 amp. Although this type of heating cycle apparently allowed little time for "homogenization," close approximations to equilibrium conditions were usually obtained as a result of the very strongly exothermic reactions between zirconium hydride and boron at elevated temperatures. Reproducibility of results in repeated runs under varying conditions was taken as a reasonable indication that equilibrium conditions had been effectively achieved. Quenching was accomplished by rapidly immersing the entire die, containing the reaction products, in water. Specimens could also be cooled at controlled rates by adjustment of the rate of flow of water through the water-cooled copper electrodes in contact with the graphite dies.

Jan 1, 1954

By B. L. Averbach, M. F. Comerford, M. B. Rough

The volume fraction of ß phase was determined in a Ti-6Al-4V alloy by measurements of integrated diffraction intensities. The (0002), and (100)ß diffraction lines were chosen because this combination minimizes the errors resulting from preferred orientation. The difficulties arising from fluorescence radiation were eliminated by use of a diffracted beam monochromator. A specimen quenched from 1475OF (800°C) contained approximately 5 pct ß, but in specimens quenched from higher temperatures no ß was found. The ß phase formed during aging, and in specimens solution treated at 1570oF (855oC) approximately 10 pct ß was present after aging at 1000°F (540°C) for 24 hr. This ß appears to form by decomposition of martensitic a&apos;. ThE kinetics of the reactions which occur during the heat treatment of titanium alloys are complex &apos; and not completely understood. It has been proposed that hardening occurs in some alloys&apos; on aging by the precipitation of a transition phase w followed by the formation of the stable a and ß phases. It has been proposed for other alloys2 that the a&apos; marten-site decomposes by precipitating finely dispersed a particles. Most investigations have been hampered by the difficulties of determining quantitatively the amounts of the various phases present. This paper is concerned with the measurement of the amount of ß phase by an X-ray method, similar to one developed for the determination of retained austenite. The principal new feature was the use of a mono-chromator in the diffracted beam in order to reduce the fluorescence arising from the sample. EXPERIMENTAL PROCEDURE The experiments were carried out on an alloy of nominal composition Ti-6Al-4V (actual weight percentages: 6.2 Al, 4.1 V, 0.02 Mn, 0.17 Fe, 0.005 H, 0.03 C, and 0.02 N). The material was received as 5/8-in.-diam centerless ground rods in the annealed condition. The heat treatments were carried out in a vacuum of approximately 0.03µHg. The X-ray intensity measurements were made on 3/8-in. thick discs. The surface was prepared by grinding off about 0.060 in. and electropolishing in a solution af 60 ml (70 to 72 pct) perchloric acid in 1000 ml glacial acetic acid with a current density of 0.5 amp per sq cm.q The X-ray determination is based on the proportionality of the diffracted intensity of each line to the volume fraction of the corresponding phase. In calculating the intensities for a powder sample it is assumed that a large number of grains con- tributes to the diffracted intensity and that the grains are oriented at random. The presence of preferred orientation introduces serious errors in the relative intensities. The material used in this investigation exhibited a strong preferred orientation, which could not be removed by heat treatment. Other investigators have also found that preferred orientation may be retained after phase transformations. Glen and pugh5 performed a detailed analysis of the randomness expected after several allotropic transformations, but stated that this is not observed. Burgers,6 and Burgers and Ploos van Amstel,7 found that, in zirconium, the original orientation is retained after two phase transformations. Newkirk and Geisler8 observed similar behavior in titanium. On the basis of this evidence, it appears that, in the absence of plastic deformation, textures present in annealed titanium alloys are retained. Heating an a-ß alloy to the all-ß region and subsequent cooling to room temperature do not make the orientation of the mar-tensite different from that of the original a phase. In the present investigation it was possible to take advantage of the crystallographic relationships involved in the martensitic transformation to minimize the errors associated with preferred orientation. The relative orientation for titaniu-m marten-site9 takes the form (0001), 11 (110)ß; [1120], 11 [lll]ß. The same relationship has been proposed for zirconium&apos; and certain titanium-base alloys.10-12 Additional sets of approximately parallel planes have been determined for titanium-nickel alloys." The influence of preferred orientation can be minimized by comparing intensities from parallel planes in the two related phases. If it is assumed that each family of planes in a given phase is equally well populated, the effect of preferred orientation can be eliminated by using the normal multiplicity for the family of planes since each set of parallel planes is equally preferred for any orientation of the sample relative to the X-ray beam. The most suitable combination of reflections in the Ti-6A1-4V alloy appeared to be (0002), and (110)ß It must be recognized that the ß formed during aging of the Ti-6A1-4V alloy is a precipitate rather

Jan 1, 1960

By Ralph E. Wood

X-ray fluorescence analysis can be profitably applied in the mineral industry by improving evaluation and control analyses, while offering lower cost and greater speed than conventional methods. Chemical analyses are not only a major item of cost in exploration and mining, as well as in milling and chemical treatment, but often cause evaluation and control of processing steps to lag behind operations. In the fields of geology and mining, the X-ray technique can be employed without destroying samples and, if necessary, specimens can be analyzed and then used, unchanged, in other evaluation techniques. Results are quickly made available for decisions on progress of exploration or sorting of waste and ore.

Jan 6, 1959

By C. N. Kravig

STANDARD raises at Homestake are 150 ft long. Raises of more than 150 ft, driven with the use of a cage and hoist, are considered long raises- some have been driven more than 900 ft. Long raises have eliminated the need for access drifts on each level when transfer and ventilation raises are driven. These timbered cage raises, 7x9 ft in cross section, include a rock compartment and a combination cage, pipe, and manway compartment. To prevent excessive weight on the timbers, 10x10-in. bearing beams are cemented into hitches cut in the rock at 150-ft intervals. The beams also hold back timber movement caused by daily drawing of rock through the rock compartment.

Jan 6, 1957

By William H. Spice

Drilling activities in South Central Texas for the year 1945 continued the steady increase over the past two years, while new fields discovered for the year included four new gas fields and one field extension. In the 30 counties included in this area, which comprises district No. 1, Oil and Gas Division, Railroad Commission of Texas, 141 exploratory wells were completed, compared with 61 drilled in 1944 and 29 drilled in 1943. Of these 141 tests, 55 were field well and 86 were wildcats; 38 were completed as oil wells, S as gas and gas-distillate producers, and 95 were abandoned as dry. Atascosa and McMullen Counties were the most active in the district, accounting for 73 of the wells drilled.

Jan 1, 1946

By J. C. Shyne, T. D. Gulden

The steady-state creep behavior, in compression, of indium containing a dispersion of atomized glass particles was studzed over a range of temperature, stress, and composition. The observed behavior was not consistent with a simple model of dislocation climb over dispersed particles. From room temperature to about 100°C the temperature dependence could be described by an activation energy about one and a half times that of self-dijfusion in indium while at higher temperatures a much higher ternperature dependence was observed. THE value of dispersion-hardened and precipitation-hardened alloys has long been recognized. The mechanism of hardening, however, is not completely understood, especially at elevated temperatures where dispersed particles increase creep resistance. Following the suggestion of Schoeck1 that the rate of creep in dispersion-hardened materials is controlled by dislocation climb over second-phase particles, Ansel and weertman2 derived steady-state creep equations for dispersion-hardened materials. Their derivation was based on dislocation climb over non-deformable spherical particles in a metallic matrix. For low stresses they predicted a linear relation between applied stress and steady-state creep rate. For stresses large enough to cause dislocations to pinch off around the precipitate particles, the theoretical creep rate was shown to be proportional to the fourth power of stress. For very high stresses an exponential stress dependence was predicted. In all cases the theoretical creep rate is linearly proportional to the diffusion coefficient. This provided the primary temperature-dependent factor. Subsequently, Ansel and Lenel3 reported some experimental data on SAP, a composite of aluminum and aluminum oxide, that was in good qualitative agreement with the above theories. Their experimental creep rates, however, were four orders of magnitude less than the theory predicts. This was attributed to a low density of active dislocation sources in the material; somehow the dispersed particles inactivated the dislocation sources instead of merely interferring with dislocation motion. Meyers and sherby4 have recently reported on the creep behavior of SAP. Their results were inconsistent with a simple dispersion-strengthening model and led them to conclude that a continuous network of oxide controls the high-temperature mechanical characteristics of SAP. Because of the rather complex mechanical behavior of SAP and the lack of agreement about the morphology of its oxide phase, it appeared desirable to study the creep of a dispersion-strengthened material of controlled morphology. For the present work a dispersion of spherical glass particles imbedded in a matrix of indium was chosen. The microstructure of this material was similar to the idealized uniform dispersion of hard spheres in a deforming matrix assumed by Ansel and Weertman in their theoretical treatment. SPECIMEN PREPARATION For experimental convenience, it was decided to use a low melting-point metal in this investigation. It was necessary that the metal not be oxidized readily up to its melting temperature and that it wet the second-phase particles. It was desired that the material chosen for the dispersed phase be available as a fine powder with closely controlled size and shape. The material chosen to satisfy these requirements consisted of a matrix of indium metal containing a dispersion of atomized particles of a soft soda-lime-silica glass ranging from 5 to 30 µ in diam. The glass particles had a highly regular spherical shape. The composite was made by stirring the glass powder into liquid indium maintained at a temperature just above the melting point of indium, 156°C. The creep specimens were prepared by a hot pressing operation. Five to ten g of the mixture were placed in a steel die and pressed at 125°C for 5 min under a pressure of 30,000 psi. The resulting specimens were cylinders about 3/8 in. in diam and ranged from 0.4 to 0.7 in. high. By following this procedure a uniform dispersion was obtained in the creep specimens. Typical microstructures of specimens containing twenty and forty volume percent glass powder are shown in Figs. 1 and 2. Unfortunately, grain size could not be determined by the metallo-graphic techniques used. CREEP TESTING PROCEDURE Creep tests were performed in compression under constant stress. The specimens were placed in

Jan 1, 1963

By Robert F. Mehl

EXTENSION of physical and chemical methods of research in the study of metallic behavior continues rapidly, particularly in the correlation of behavior with crystal structure, and in the analysis of elastic and plastic properties. The growth of the science of metals during 1933 calls for special comment; the need for special reviews and for textbooks and monographs is now acute, as might he supposed from the number of references appended to this article, a list which is much abbreviated.

Jan 1, 1934

By W. Hodge, A. F. Haskins, R. M. Evans

Refractory boron compounds are shown to resist corrosion by molten zinc. Coatings were made from ferroboron and manganese boron by several methods: welding, hard facing, and pack diffusion; and techniques of coatings are very important. Mechanical failure of the diffusion coatings can be partially eliminated by applying them to type 416 chromium steels rather than carbon steels. Welded coatings made with a tungsten arc are better than those made by other welding methods. Sintered compacts of mixtures of iron and chromium borides developed strengths of about 30,000 psi. They resisted corrosion of zinc at 600°C and oxidation at higher temperatures. MOLTEN zinc rapidly attacks common metals of construction. The rate of attack is greatly amplified at temperatures over 500°C. However, there are many applications where it is necessary, or at least advantageous, to use metal construction, such as for galvanizing pots and zinc smelter equipment. Condensers and agitator linings used in continuous zinc smelting processes are eroded and corroded by violently agitated molten zinc. Pumps, tubing, and other parts to permit transfer of molten zinc would be desirable in many zinc handling operations. The development of metallic materials which are resistant to molten zinc also might permit its use as a heat-transfer medium in modern high efficiency power plants. In reviewing previous work on zinc-resistant metals, it was evident that most of the available data refer to corrosion at temperatures just above the melting point. Tungsten and high Mo-Fe alloys containing more than 80 pct Mo resist corrosion by molten zinc.&apos;, &apos; Imhoff states that because chromium is not attacked by zinc, chromium plating improves galvanizing pot life." Nitrided cast iron has been used in die-casting machines&apos; where the molten alloy is 96 pct Zn and 4 pct Al. Other metals that have been suggested as of possible value for zinc resistance are columbium, tantalum, and titanium.V he corrosion of steel by zinc has been discussed by many authors,z, "2 None of these materials resisted corrosion by molten zinc at the temperatures used in this investigation, i.e., 600" to 700°C. I. Exploratory and Resistant-Coating Tests To make a study of zinc-resistant metals, exploratory tests were conducted to sort out roughly those materials which seemed most worthy of further development. This preliminary study included both solid metals and surface coatings. Exploratory Corrosion Tests in Molten Zinc—In initiating a study of this problem, numerous samples of metals and alloys were evaluated by dynamic corrosion tests made at 440 °C. Each metal was tested in its most readily available form, which, because of shape and size, was often unsuited for standard corrosion testing. The equipment used for dynamic corrosion testing of all materials, except in a few initial experiments, is shown in Fig. 1. Samples were tied to tungsten rods with tungsten wire, immersed in the zinc, and revolved at 12 rpm about the circumference of a 4 in. diam circle. Speed of travel was about 12.5 fpm. The molten zinc was protected from oxidation by an atmosphere of carbon monoxide, or, at a later period in the program, by a 9:1 mixture of nitrogen and hydrogen. When the effect of both molten metal and atmosphere was desired, the zinc level was lowered. Special high grade zinc was used in all of the corrosion tests. Corrosion losses for materials tested are shown in Tables I and 11. Whenever the materials were available in suitable form, the losses are reported in mils per year. It was recognized that weight losses on irregularly shaped specimens did not show the corrosion rate but the important consideration—poor resistance to corrosion—could be determined readily.

Jan 1, 1956

By W. C. Elli, M. E. Fine

YOUNG&apos;S modulus of elasticity in metals ordinarily decreases with rising temperature. The range of the thermoelastic coefficient at room tem- 1/E dE/dT perature (temperature coefficient of modulus, is illustrated1 by the values for tungsten and hard-drawn aluminum, —95 and —1220x10-6 eg C-1. However, a nearly zero thermoelastic coefficient is observed in some ferromagnetic alloys over a limited temperature range. In these alloys, as the temperature is raised, an increase in modulus arising from loss of ferromagnetism compensates the normal decrease. Iron-nickel alloys containing 36 to 52 pct Ni behave in this manner. In the present investiga- tion, the dependence of the modulus and thermo-elastic coefficient on cold working and annealing were studied in iron-nickel alloys in this range of nickel. Although these alloys, when fully annealed, have a coefficient near zero over a very small temperature interval, the temperature range of low coefficient can be extended greatly by straining and then stress-relief annealing. The modulus of face-centered cubic iron-nickel alloys annealed at 1000°C does not vary linearly with composition at room temperature but, as shown by the solid line of fig. 1, from Koster,&apos; is minimum at 40 pct Ni and maximum at 87 pct Ni. The modulus increases with applied magnetic field but retains the minimum near 40 pct Ni. Schematic change of modulus with temperature for three compositions is shown in fig. 2.&apos;. &apos; With increasing temperature, the slope becomes less negative, goes through zero (temperature of minimum modulus for the alloy), becomes positive, and resumes its normal negative value above the Curie

Jan 1, 1951