Search Documents

By I. S. Levy, J. L. Brimhall, B. Mastel

Specimens of' Hastelloy X-280, a low-cobalt version of the solid-solution- hardened nickel-base alloy Hastelloy X, were given a series of thermomechanical treatttzents. They were then Lensile-tested at room temperature and 1350°F. The Microstructures of the specimens tested at 1350°F were studied by electron Microscopy. Microscopy showed that dislocation tangling, caused by the cold working, mas still in evidence after aging-for 24 hr to temperatures as high as 1550oF. (Cr, Mo)23 C6, (Fe, Mo)6 C'. as well us an unidentifiable phase precipitale due to the combination of the thermomechanical treatments and subsequent tensile strain. The room -temperature and 1350°F tensile properties show a general increase ill strength and decreccse in ductility with increusing cold-work level. This is due to the dislocation taangling-. PerLurbatiot~s to this general trend occur- due to solid-solution weakening at the higher cold-work levels as a direct result of the preciplitation reactions. THE requirements for corrosion resistance and high-temperature strength place nickel-base alloys among the more promising materials for advanced nuclear reactor applications. However, when these alloys are irradiated at service temperatures, they generally suffer severe embrittlement'" and reduction in rupture life.3 Certain experimental treatments resulted in improvements in the tensile and stress-rupture properties of Hastelloy X-280, a solution-hardened nickel-base alloy.' To provide a basis for understanding these improvements, unirradiated tensile specimens were examined by electron microscopy. The results are reported in this paper. EXPERIMENTAL DETAILS Material. Hastelloy X-280, a low-cobalt version of Hastelloy X, is a member of the solution-hardened class of nickel-base alloys. The Hastelloy X-280 was obtained from 4- and 1-in: thick plates in the mill -annealed condition. Table I gives the chemical composition of the material as reported by the National Spectrographic Laboratories. ~x~erimental Treatments. Plates of suitable size, 12 by 3 by 1 in., or by + in., were cut under a water jet from the stock material and examined ultrasonic -ally for homogeneity of grain size and absence of voids. The acceptable plates were solution-treated at 2150°Ffor 1 hr and air-cooled. These plates were then reduced in thickness by cold rolling 0, 10, 15: or 20 pct along the original rolling direction. The plates were machined into buttonhead tensile specimens with a gage diameter of 0.125 in., with a gage length of 1.125 in., and with their tensile axes parallel to the rolling direction. The specimens were examined for quality of finish with a penetrant dye, ultra son ically checked for voids, and finally given a dimensional tolerance check with an optical comparator. The acceptable specimens were aged for 24 hr at either 1000" or 1500 F and air-cooled. These specimens were then held at 540°F in a water loop for approximately 18 days to qualify as controls for similar specimens irradiated under the same conditions of time, temperature, water chemistry, and flow rate. Table U summarizes the treatments. These treatments were investigated to establish whether prior precipitation and stabilization of carbide phases at strain sites within the matrix could reduce the amount of carbides available for precipitation at grain boundaries during service. Tensile-Test Conditions. Specimens were tested to fracture at room temperature or 1350 F in air on an Instron tensile-testing machine at a crosshead speed of 0.05 in. per min. The time for the furnace to reach equilibrium at 1350°F was approximately 30 min; soak time prior to testing was 15 min; and test duration was approximately 5 min.

Jan 1, 1968

[¦Abad, Leopoldo F., College of Min., Univ. of California Berkeley, Cal. '23 ¦Abarquez, Ramon F., Met., Bureau of Science Manila, P. 1. '24 ¦Abbey, Robert Graham, Student, Case School of Applied Science Cleveland, Ohio. '21 Abbott, A. N., Mines Supt., Mazapil Copper Co., Ltd ...Concepcion del Oro, Zacatecas, Mexico. '23 Abbott, Clarence B., Gen'l Supt., Iron Mines Div., Tenn. Coal, Iron & R. R. Co., 1405 Minnesota Ave., Bessemer, Ala.' '04] [ ]

Jan 1, 1925

By P. Duwez, L. Zwell

L. S. BUSCH—We have had presented two methods of measuring these variations in powder compacts. E. OROWAN—Tn connection with the rolling mill research work carried out at. the Cavendish Laboratory, Cambridge, with the help of the British Iron and Steel Research Association. Dr. E. A. W. Hoff, Mr. J. Los, and myself, have determined coefficients of friction at ex- treme pressures for a number of liquid and solid lubricants, both by direct measurement, and by calculation from measured values of the roll force. The most efficient lubricants at these high pressures (for the small amounts of sliding that, occur in rolling) were camphor and. in particular, borneol (Borneo-camphor). Perhaps such lubricants could be used with advantage in the kind of work described by Dr. Wulff. L. S. BUSCH—1 think Dr. Wulff has in the past mentioned experiments which have been performed in the extrusion and rolling of metals and which led to conclusions which can be applied to the compacting of metal powder. A. SQUIRE*—There have been some recent developments in the field of high pressure lubricants which indicate that boron nitride might be a very desirable material to employ as a die lubricant. At the present time its cost is prohibitive, but as the need arises for the material it will undoubtedly come down in price. The present price is $200. a pound. It is my understanding that one of the reasons for vacuum pressing both in ceramics and metal powders, is to prevent

Jan 1, 1950

By JOHN JERMAIN

In my opinion, the explanation of the fuel-requirements involving the conception of heat available and necessary above a critical temperature, as advanced by Johnson 1 and elaborated by Howe, Raymond and others,2 affords a theoretically correct basis for such an accounting. It is the purpose of this paper to set forth a first crude attempt to construct a formula which shall show quantitatively the relation between the various factors affecting fuel-economy, and afford a means of comparing the enormous amount of data on the fuel-consumption of various blast-furnaces, at various times and under various conditions of operation. I have also applied this formula to a large number. of individual cases, and have, by its means, compared the furnace-practice of several important iron-making districts. II. DERIVATION OF FORMULA FOR FUEL-REQUIREMENTS. The general expression for the fuel-requirements of the blast-furnace, which I believe to be theoretically correct as to form, is as follows Carbon per ton of iron = Heat per ton of iron necessary in hearth above Tc./Heat per pound of carbon available in hearth above Tc. XFactor of rate of driving. +Carbon dissolved by CO2 of flux. +Carbon dissolved incidental to reduction of ore. + Carbon dissolved in pig-iron. (NOTE.-Tc = critical temperature.) Since, according to Johnson's theory, fuel-economy is usually limited by heat available and necessary in the hearth, rather than by the total heat supplied and necessary, we may write Carbon needed in hearth = Hn/Ha in which Hn is the heat per ton of iron necessary in the hearth above some critical temperature, and Ha is the heat per pound of carbon available in the hearth above this same critical tem¬perature. 1 Trans., xxxvi., 454 (1906). 2 Trans, xxxvi., 792 to 798 (1906) ; Trans, xxxvii., 216 to 237 (1907).

May 1, 1911

ARTHUR PHILLIPS, Chairman C. S. SMITH, Past-Chairman L. W. KEMPF. Vice-Chairman. E. E. SCHUMACHER, Vice-Chairman H. A. MALONEY, Treasurer FRANK T. SISCO, Secretary °9 West 39th Street, New York 1S, N. Y. Executive Committee 1945 1946 S. BARRETT H. L. BURGHOFF T. A. WRIGHT GERALD EDMUNDS L. L. W MAN A. A. SMITH, JR.

Jan 1, 1944

By M. E. Straumanis, S. M. Riad

The lattice parameter of 99.999 pct pure Ag rtlas redetevnzined and found to be az5 = 4.08626 5 0.000041 with the vefnzctiotz correction included); the expatzsion coejjicient between 10° and 65°C was 18.73 X10-6°C-1. The lattice paratneter increased upon solution indium in silver in good agrement with other authors. The solid-solubility limit around room temperature was at 20.4 wt pct of in, which suggests that the high-temperature solubility (at about 689°C) determined by other authors is too low. The expansion coejficient of si1ver increases with the itzcrease of indium content between 10° and 65° C from, 18.73 (In = 0) to 20.9 x 10-6°C-1 (In = 20.4 pct), being only very slightly influenced by small amounts of indium. The expansion coefficents of all solid solutions increarsed strongly with temperature, reaching values > 27 x 10- 6 800°C. ACCORDING to the Ag-In diagram,' the solubility of indium in silver (the a phase) extends to about 18 pct by weight at room temperature. However, there has been only one investigation of the solubility limit by X-ray methods—that of Weibke and Eggers.2 Hume-Rothery, Lewin, and Reynolds measured only the lattice parameters of Ag-In solid solutions3 as did Owen and Roberts4 and Adler and Wagner.' The thermal expansivity of four solid solutions was determined by Owen and Roberts4 in a temperature range between 25" and 300°C. In view of the limited amount of work on Ag-In solid solutions, it seemed appropriate to redeter-mine the lattice parameters and the room-temperature solid-solubility limit, to find the exact expansion coefficients of the solid solutions at about room temperature (between 10° and 60°C) and the expansivity up to 800°C, and finally to derive the thermal-expansion coefficients for any alloy within the solid-solubility region. THE ALLOYS AND THE DETERMINATION OF LATTICE CONSTANTS The metals used were 99.9991 pet pure, supplied by the ASARCO company. Both silver and indium were weighed accurately on an analytical balance in

Jan 1, 1965

By J. R. Mihalisin, J. S. Iwanski

The response of Inconel "700" to heat treatment has been studied by light and electron microscopy combined with X-ray and electron diffraction techniques. A heat treatment which vesults in low ductility for this alloy appears to be associated with the formation of MC carbide in a Widmanstdtten distribution. This type of precipitation can be suppressed by suitable heat treatment with concurrent increase in ductility. Various other phases precipitated in this alloy are also identified. RECENT studies of commercial nickel base su peralloys have demonstrated the importance of the morphology of carbide phases upon physical properties.' For example, empirical heat treatment studies applied to Nimonic "80" and Inconel "X" have resulted in prescribing double aging treatments for optimum physical properties. These treatments have subsequently been related micro-structurally to grain boundary carbide morphology.2 The purpose of this study was to obtain information about the morphology and identity of some of the phases precipitated in Inconel "700" after heat treatment. It was hoped that some correlation could be made of micro structure with heat treatment similar to that observed with Inconel "X" and Nimonic "80." EXPERIMENTAL PROCEDURE Specimens were obtained from a hot-rolled bar of Inconel "700" of the following composition: C Mn Fe S Si 0.10 0707 0.42 0.007 0.12 Cu Cr -A1 -Ti- Co Mo Ni 0.02 -14.90 TM 2.22 27.61 2.92-- Bal. Specimens were prepared in the following heat-treated conditions: (A) 2275°F for 2 hr WQ (B) 2275°F for 2 hr WQ + 2000°F for 1 hr (C) 2275°F for 2 hr WQ + 1600°F for 48 hr. (D) 2275°F for 2 hr WQ + 2000°F for 1 hr + 1600°F for 48 hr. Empirical stress-rupture studies had shown that treatment (D) resulted in optimum stress-rupture life and ductility. Treatment (C), although giving a good aging response, resulted in low ductility. Treatments (A) and (B), respresenting individual. steps in treatments (C) and (D) were added here for microstructural comparison studies. The procedure was to make an optical and electron microscopic investigation supplemented by X-ray diffraction analysis of electrolytically extracted residues. Electron diffraction studies were made utilizing selected area diffraction techniques with extraction

Jan 1, 1960

By Oliver Bowles

THE most important non-metallic mineral industries from a tonnage standpoint are those that are allied with the construction industries and are engaged in handling sand and gravel, crushed stone, building stone, cement, lime and gypsum. The greatest problem facing a number of these industries at this time is over-production. They have experienced un- usual, and in some instances phenomenal, growth during recent years, stinlulated by extensive highway and building construction, but in some localities expansion of producing plants has far outstripped industrial needs. The cement industry is operating at about two- thirds capacity. Over-production tends toward price- cutting and unprofitable and interrupted operation, involving maintenance expenses for idle plants and disorganization of working forces. This condition has encouraged active efforts toward reducing production costs by the introduction of labor-saving equipment. Also, there is a tendency toward the location of manufacturing plants, wherever possible, near the centers of consumption rather than at points of production of raw materials. In order to reduce overhead expense, or for other reasons, many consolidations of companies into larger units have taken place. An economic study of conditions in these industries is highly desirable. The U. S. Bureau of Mines has taken one step forward in this direction in the issuance of Economic Paper 7, entitled "Economics of New Sand and Gravel Developments." Briefly, this report emphasizes the importance of making a thorough study of all the economic factors involved before undertaking new .enterprises.

Jan 1, 1930

By F. L. Bosqui, A. D. Wilkinson

EVEN though the world has not been crying for more copper for the last three or four years there has been some important mill and smelter construction. Discovery and development of large new high-grade copper deposits in Africa has led to the construction of extensive reduction facilities there, prominent among which is the concentrator and smelter of the Rhokana Corporation at N'Kana. Northern Rhodesia. The 3000-ton concentrator adjoins the central shaft. A little over half a mile to the southeast, at an altitude of 40,010 ft., is the smelter, designed on the site by 1. H. Wynne. It is arranged primarily to treat N'Kana copper concentrates, but can also handle concentrates and direct-smelting ore from outside sources. Excavations were started late in 1930; concrete was first poured on Jan. 6. 1931; and the first blister cop¬per was cast on March 1.9, 1932, less than fifteen months later. During this period, which included several months of heavy tropical rains, some 10,000 cu. yd. of concrete was poured and 41000 tons of structural steel erected under the supervision of construction engineer, A. Ek, with a labor force of 60 to 30 Europeans and about 300 natives. The steelwork was fabricated by Head Wrightson & Co. in England, and the boiler plant equipment furnished and erected by the International Combustion Co. Ltd.

Jan 1, 1934

By S. A., Taylor

IT is very difficult to arrive at exact figures for the cost of maintaining excess capacity of coal mines, but we can approximate the various items. To do this, I will take the Pittsburgh district of Pennsylvania and the other districts can be compared to this one. I believe we can take the depreciation item of plant ac- count as a whole and discount it over a period of 20 years; while this is high for some items it is low for others and I believe it is not far from a safe basis. This equals 5 per cent per year, and this depreciation will take place about as rapidly when not in use as when in operation. A fair value in the Pittsburgh district to- day for plant and houses is close to $4 per ton per annum. At 5 per cent this will equal 20 cents per ton per year. The item of keeping the mine in condition, free from water, etc., will be close to an average of 2y2 cents per ton per annum.

Jan 1, 1928

By J. B. Newkirk, A. H. Geisler

The alloy Cu4Pd has a disordered face-centered-cubic structure when quenched from temperatures between 478ºC and the melting point (about 1100°C). Below 478ºC an ordered phase is stable. The results of a Debye-Scherrer X-ray analysis indicate that the ordered phase has a tetragonal unit cell described by the space group C24h — P42/mt with 2 Cu in 2a, 2 Cu in 2f, 4 Cu in 4j (x = 0.2, y = 0.6), 4Pd in 4j (x = 0.4, y = 0.2), and 8 Cu in 8k (x = 0.1, y = 0.3). The orientation relationship between the face-centered-cubic phase and the ordered tetragonal phase is given by: [100],,. // [130]al,. COO1Ia.d.//COO1I,,.. • The behavior of Cu,Pd is typical of ordering alloys except that the transformation is very sluggish. The increase in hardness and the microstructural and X-ray diffraction effects are interpreted in terms of coherency strains caused by the ordering. AN anomalous construction in the Cu-Pd phase diagram (Fig. 1) was reported in 1939 and has been allowed to stand without further published attention since that time. The odd figuration about the composition 10 to 27 atomic pct Pd is derived mostly from the work of Jones and Sykes.1 Evidently several features of this binary system require further study if the constitutional forms are to be well understood. The present paper includes a study of one of these features, that is, the crystal structure of a single ordered alloy containing nominally 20 atomic pct Pd. This choice of composition was suggested by the work of Harker and associates who determined the structure of Ni4Mo2 and Ni4W.3 The nature of the ordering process in Cu4Pd was studied also by observing the hardness, microstructure, and Debye-Scherrer patterns of specimens which had been aged at various temperatures after quenching from an initial disordering treatment. Experimental Methods A 20 gram ingot of Cu4Pd was made by melting spectrographically standardized copper from Johnson, Matthey, and Co., and commercially pure (99.5 + ) palladium in an argon-filled quartz tube. Chemical analysis showed that the ingot contained 80.0 atomic pct Cu. The ingot was rolled about 60 pct to a strip 0.060 in. thick and was homogenized for 16 hr at 950°C in low pressure argon. Rods cut from the rolled strip were worked into wire 0.015 in. in diameter, and specimens for hardness and microscopic examination were cut from the remaining strip. All specimens, with the exception of some of the wire, were given an initial disordering treatment by heating for 16 hr at 950°C, followed by water quenching. A 10 cm length of as-drawn wire was water quenched after being held in a temperature-gradient furnace4 for 89 days. Room-temperature Debye-Scherrer photograms were then made at points along the wire to determine the temperature below which the ordered phase was stable. Although the accuracy of temperature determination in the gradient was only about ±10 °C, the temperature gradient was sufficiently gradual that the sensitivity was much better and locations which had differed by as little as 1°C could be distinguished. An analysis of the crystal structure of the well ordered alloy was made by X-ray diffraction using a specimen cut from this wire. The change of Debye-Scherrer pattern as ordering progressed was studied by using isothermally aged samples of initially disordered wires. The wires were sealed under low-pressure argon in small quartz tubes for heat treatment. After the aging treatment, the tubes were quenched in water and photograms were made at room temperature in a 10 cm diam camera using filtered Cu kX. (A = 1.540511) Hardness was measured on a Vickers hardness tester using a 10 kg load and 2/3 in. objective lens. Reported values are the average of at least three impressions made on flat specimens 0.060 in. thick. After the hardness of a heat-treated sample had been measured, it was resealed in low-pressure argon and returned to the furnace for continued aging at the same temperature. In this way, two samples served for all aging times at each temperature. Hardness specimens which had been aged 500 hr or more were used for metallographic examination after the final aging treatment. A dilute potassium-dichromate etching solution was used.

Jan 1, 1955

By J. J. Gilman

WHEN a zinc crystal is immersed in liquid N, and then plastically bent, it is observed that it bends a certain amount and then fractures. This fracture occurs at a fairly reproducible radius of curvature, and the radius varies systematically with the crystal orientation. Because this phenomenon provides an unusually well-defined set of fracture conditions, it is possible to examine various possible fracture criteria and select the best one. Zinc crystals of various orientations were bent about axes lying in their glide planes (0001) and perpendicular to their glide directions [1210]. The crystals were 0.150 in. diam and had chemically polished surfaces. They were immersed in liquid N, while they were being loaded on an Instron testing machine. A three-point bending jig was used to load them. Table I lists the beam radius at which fracture occurred for each orientation. Each value is the average of at least six measurements. The normal stresses on the cleavage planes, at the time of fracture, were calculated as follows: First, from the fracture radius, R,, the orientation angle, x,, of the (0001) plane at the outer fiber was calculated. If x, = angle between the (0001) and the rod axis prior to bending, d = rod diameter, and X, = angle between the (0001) plane and a tangent to the bent crystal, then1 sinX, _ 2R, sin xn 2R, + d Since the glide shear strain is given by' y ' cot X, — Xo the glide strain at fracture, x,, can be calculated. Next, it is necessary to know the tangential stress in the outer fiber at fracture. This depends on the plastic flow curve, so a series of tensile tests were performed at —196°C on another set of zinc crystals. A curve of the average resolved shear stress versus glide strain was prepared. From this curve, shear stresses, r,, corresponding to the glide strains in the bend tests were taken. These values are listed in Table I. Then the normal stresses in the outer fibres, u,, were calculated from the relation U, = r, tan X, This analysis assumes that the fiber stresses in a bent beam are the same as the stresses in simple

Jan 1, 1959

By Marcus Nadler

WAGES in the United States, in spite of the wage freeze, have increased materially. Overtime payments have become standard practice in almost all industries. Now efforts are being made to place wages on an annual basis, and if this is adopted, it will result in an increase in the cost of production. Organized labor today is more powerful than ever before; union membership is large and steadily increasing, and in many instances membership in the union is a prerequisite to employment. The treasuries of many unions are strong as a result of the large membership and full employment. The unions, therefore, today are in a much better position than ever before to carry on long strikes. Politically, too, the unions are more powerful today than they ever were. On the basis of their strength, one may expect that some of the demands that the labor unions will make in the not distant future will be granted. It is, therefore, quite evident that before long, particularly when the curtailment in war production reaches about 40 per cent, this country will be confronted with a serious labor problem.

Jan 1, 1945

By Edward H. Bzirdick

THE territory under particular consideration in this article comprises portions of La Plata and Montezuma Counties, situated in the southwestern corner of Colorado, and around the base of the La Plata Mountains. (See Fig. 1.) In southeastern Utah and northeastern Arizona there are several mountain systems whose origin and structure are practically identical with the La Platas so that ore occurrences found in the latter can be hopefully looked for in the former. With this assumption, there is an area around the laccolithic ranges which offers promise for a successful exploration for gold ores. Ore occurrences of the Silverton, Telluride, Rico, or Ouray Districts will not be discussed, although in these areas the Mesozoic sediments are more or less involved within the ore-bearing complex. These have been intensively studied and developed. The idea is to set forth what my mining experience has been within the largely unaltered . Mesozoic horizon which remains around the extreme bases of the La Plazas. This, until recent years, has been almost entirely neglected by prospectors and operators and, so far as similar territory in Utah and Arizona is concerned, so remains.

Jan 1, 1934

The annual report f the Secretary of the Navy for the fiscal year, ending June 30, 1917, but including operations and recommendations up to Dec. 1 of that year, contains the following remark about the activities of the Naval Consulting Board. The members of the Institute who are members f this Board are William L. Saunders, Benjamin B. Thayer, Thomas A. Edison, Thomas Robins, Lawrence Addicks, Joseph W. Richards, W. R. Whitney, assisted by 47 other members f the Institute, in the capacity of associate members of the Naval Consulting Board. During the year, the work of this board, organized and approved by Congress in 1915, has increased very materially in importance and volume, its meetings have been frequent and the work of its individual members has been such in some cases as to occupy almost their entire time in the service of the Government. Some time before the active entry of this country into war the board called a special meeting to which were invited some 50 of the leading scientists and industrial managers, whose special study fitted them to advise on the methods of meeting the

Jan 2, 1918

By N. R. Adsit

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from offman:"

Jan 1, 1967

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By R. G. Fenish

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from Hoffman:"

Jan 1, 1967

Henry LOUIS, London, England (communication to the Secretary) : Prof. Richards's paper has impressed me as highly valuable. Without entering upon any discussion of it as careful and thorough as it deserves, I venture to mention one or two points which a perusal of it has recalled to my mind in connection with my own study and practice of ore-dressing. I always mentally divide jigging into two phases: 1. A particle at rest on the jig-bed is lifted and carried upwards by the rising current of water, at an increasing velocity, which tends to a maximum. When the upward current is stopped, the particle continues to rise with rapidly diminishing velocity until it comes to rest. This completes the first phase. 2. In the second phase, the particle falls from its position of rest with an increasing velocity which tends again to a maximum, and continues to fall until the rising current of water has reduced its velocity to zero. This completes the second phase. The second phase will evidently be greatly modified by the effect of suction, as Prof. Richards shows; but I do not see that his experiments very clearly imitate the action of the second phase. And the brief intervals at the end of each phase, when the mineral particle, by reason of its acquired velocity, is still moving, though in opposition to the water-current, yet remain to be investigated. I feel especially, in Prof. Richards's paper, a difficulty which I have felt with regard to all similar previous investigations, namely, that the experiments deal with particles falling a long distance, when the velocity becomes uniform. I question whether this uniform maximum velocity is attained in actual jigging-practice. If so, it is certainly for a comparatively very small proportion only of each stroke. It seems to me that an investigation like that of Prof. Richards, but confined to the first 6 or 8 inches of fall only, and carried out with suitably delicate recording-apparatus, is what we

Jan 1, 1895

By R. D. Rubright, Owen J. Hart

In the Bingham district over a span of more than 90 years, 43,947,104 tons of "non-porphyry" copper, lead, zinc, gold, and silver ore have been mined from a folded and faulted alternating series of Pennsylvanian and Permian limestones and sandstones and from some Tertiary intrusives. This ore came from six major mine areas located east, south, and west of the Bingham stock, site of Kennecott's porphyry copper deposit. The sediments were affected by varying degrees and types of metamorphism within 2000 feet or more of the Bingham stock. The intrusives consisting of the mineralized Bingham and the unmineralized Last Chance stocks and numerous dikes and sills of granite and monzonite were intruded into the asymmetrical northwest-trending and plunging Bingham syncline. Extrusives, although present, contain no ore. The bulk of the non-porphyry ore in the district was found above the Midas thrust. The primary ores are found in three major types of deposits: concordant bedding fissures, crosscutting fissures, and replacement deposits. These deposits consist of both copper and lead-zinc ore bodies that contain various amounts of gold and silver. These are in places roughly zoned both laterally and vertically and have been mined for up to 10,000 feet outward from the center of the Bingham stock and up to 5000 feet vertically below the surface. Secondary ore was of minor importance and was found in and under the oxidized zone at shallow depths. Genetically the Bingham stock, the ores, and related phenomena have had a common source.

Jan 1, 1968