Search Documents

By Lawrence Adler

In-situ rock has well-recognized rupture and yielding responses. Attention is called to an intermediate response, granulation, which consists of an evenly distributed, small-scale crumbling accompanied by swelling. Granulation results in a negative slope for the inelastic portion of the stress-strain curve as successive interlocks are destroyed, and the load-carrying capacity of the material is reduced. Volumetric swelling with softening also takes place. The prerequisites for such a response are moderate confinement and a uniformly distributed defect pattern. Since rock masses, as well as rock as an intact material, have such patterns in their jointing and texture, respectively, granulation is characteristic of them. The presence of granulation can be demonstrated for a very wide scale, ranging from laboratory testing to regional geologic phenomena. The response of an engineered structure is considered in detail. Granulation appears to be dependent upon internal moments, the formation of which can be controlled by engineering design. The practical implications of such control can be significant in optimizing underground instability and in improving excavation techniques. Rock is usually considered to behave inelastically under high load, by fracturing as a brittle material, or by yielding as a ductile material, ignoring time dependency. These responses, which are characteristic of metallic behavior, appear idealized in Fig. 1, where linear-elasticity approximates the initial behavior. However, another major deformation mechanism peculiar to rock has long been recognized in geology, the granulation of an interlocked material. Granulation consists of a uniformly distributed fracturing and crumbling of the material, accompanied by swelling and softening. Predictably, the associated inelastic portion of the load-deformation curve has a negative slope,

Jan 1, 1971

By P. A. Beck, M. V. Nevitt

All binary and a number of ternary u alloys formed by first long period transition elements were examined and found to be ferromagnetic at low temperatures. The Curie temperatures for these alloys were measured. It was found that the correlation of the Curie temperature with composition may be described qualitatively in terms of the contributions of the various component atomic moments to the saturation moment of the alloy. Ternary Fe-Cr-Mo u phase alloys were also found to be ferromagnetic, with a Curie temperature dependent on the iron content and largely independent of the unit cell dimensions. Similar relations were found for the Co-Fe-Cr and the Co-Cr-Mo a alloys, where the Co + Fe content appears to determine the Curie temperature. RECENTLY, it has become increasingly evident that the u phase is some kind of an "electron compound." Several papers1-' discussed the empirical correlation between the composition of the various u phases in alloys of the transition elements and the distribution of electrons in the partially filled d-levels of the component atoms. However, a picture of the latter can be formed only in a more or less intuitive manner, as in the Pauling theory," and the rigorous treatment of these problems is at present prevented by lack of adequate knowledge of the electronic structure of the transition elements in the metallic state. It appeared reasonable to expect that investigation of the magnetic properties, which are related to d-shell electrons, may help in clarifying the physical nature of the foregoing empirical correlation. Qualitative tests of samples of various compositions have shown that certain u alloys become ferromagnetic at liquid nitrogen temperature." The present investigation was undertaken to determine whether or not low temperature ferromagnetism is characteristic of a large variety of u alloys and to establish how the Curie temperatures of ferromagnetic u alloys are influenced by changes in composition and in lattice parameter. In the first portion of the in- vestigation, Curie temperatures were measured for a series of u alloys containing either vanadium or chromium with one or two of the elements manganese, iron, cobalt, or nickel. In the second phase of the work, data were obtained on the Curie temperature of ternary (Fe, Co, Cr)a, (Fe, Cr, Mo)a, and (Co, Cr, MO)U alloys, as a function of composition and of interatomic spacing. Experimental Procedures High frequency vacuum melting in high purity re-crystallized alumina crucibles was employed in the preparation of the u alloys, using metals whose lot analyses are given in Table I. Approximately two-thirds of the alloys were analyzed chemically, the analytical results being in acceptable agreement with the intended compositions, as seen in Tables I1 and 111. The specimens were annealed for homogen-ization in an atmosphere of purified 92 pct He and 8 pct H, mixture or in evacuated and sealed Vycor tubes at temperatures from 780" to 1300°C, depending on the temperature range of the u phase field for the particular composition. The annealing temwerature and time for kach alloy are given in Tables 11 and 111. Curie points were determined by an induction method; the change with temperature of mutual inductance between two coils was observed when the i-u specimen was inserted into the flux path between the coils. The transformer consisted of three coils each containing 1200 turns of 0.0050 in. diam enameled copper wire. The center coil, P in Fig. 1, served as the primary coil, and was linked magnetically with each of the two secondary coils, S, and S? which were connected in series opposition. The primary coil, P, was energized by an audio-oscillator, set at a frequency of 500 cycles per sec, while the signal from the transformer secondary circuit,

Jan 1, 1956

NORTH AMERICA Number Members Alaska 31 Canada 302 Mexico 175 Newfoundland 3 United States Alabama 52 Arizona 131 Arkansas 9 California 723 Colorado 184 Connecticut 98 Delaware 19 District of Columbia 133 Florida 16 Georgia 6 Idaho 61 Illinois 241 Indiana 57 Iowa 7 Kansas 32 Kentucky 33

Jan 1, 1932

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By D. L. Katz

The Oklahoma City Wilcox sand, discovered on March 26, 1930, has produced 394 million barrels of crude oil and 819 billion cubic feet of natural gas as of July I, 1941. The 100,000-bbl. wells, pressures of 2600 lb. per sq. in., and flows of "Wilcox" sand caused exciting moments in the early life of the field. Today the reservoir is substantially at atmospheric pressure and produccs 75,000 bbl. of crude oil daily through 466 pumping wells. Early estimates of the initial crude-oil content of the "Wilcox" sand1 indicated that about 600 million barrels of crude oil would remain after the pumping wells ceased to produce economically. The Oklahoma City Wilcox Secondary Recovery Association was organized in March 1939, to study the possibilities of recovering a portion of this oil. Only a very brief summary of the information available can be presented in a paper of this nature. Some simplifications and generalizations are necessary to give the over-all picture in SO short a space and statements made may not apply to a specific well or small area. Since the area under consideration by the Association is that north of the south line of section 22-11-3, some information will be presented for areas A, B, C, 1, 2, 3 and part of 4 of Fig. 2, and some will be for the entire Wilcox zone west of the fault. This paper is essentially an abstract of an engineering report made by A. D. Small, B. T. Murphree, M. C. Sons and the author for the Oklahoma City Wilcox Secondary Recovery Association on Sept. 5, 1940. Some information is taken from a report to the Association by C. V. Sidwell on March I, 1940, and some data are from a recent report by A. D. Small. It gives a brief history of the Wilcox zone, estimates of the initial oil contents of the reservoir, present conditions in the reservoir, and probable results from several programs of "secondary recovery." History of Wilcox Zone The Wilcox sand lies on the flank of the general structure, as shown by cross section of Fig. I2,3,4 and areal map of Fig. 2. The sand is of Ordovician age and is composed of well assorted, rounded sand grains with no apparent cementing material. The loose texture of the sand is shown by the enormous quantities of sand production from the wells and from the soft cores. The productive sand varies from zero thickness on the east to 220 ft. maximum and to zero thickness on the west because of water. The development of the pool4 as dependent upon drilling restrictions within the city limits, which accounts for the spacing of drilling operations listed in Table I by years. In 1931, areas I through 7 of Fig. 2 were open for drilling with the exception of some west-edge properties, and all wells drilled before Feb. I, 1935, were in this portion of the field. Nearly all wells drilled from 1933 to 1037 were in areas A, B and C. Since 1939, the newly drilled wells have gradually enlarged the producing area toward the west in the northern portion.

Jan 1, 1942

By C. O. Burgess, W. D. Forgeng

DESPITE the increasing interest in and the technical importance of iron-chromium-manganese alloys, very little published information is available regarding their constitution. F. M. Becket's paper1 in 1930 represents the first correlated effort in the field of these alloys. The paper served particularly to draw attention to the commercial possibilities of iron-rich alloys containing chromium and manganese in balanced proportions. The duplex structure of alloys within the commercial range was briefly discussed, but exposition of their structural constitution was necessarily limited because the physical properties and corrosion resistance of the alloys were the main subjects of the paper. Both prior to and following the publication of F. M. Becket's paper, and at his instigation, an extensive investigation of the constitution of iron-chromium-manganese alloys of commercial purity was in progress at the Union Carbide and Carbon Research Laboratories, Inc. The present paper is based on the results of that investigation. In the last few years, investigations covering various portions of this alloy system have also been made in Europe. W. Koester briefly mentioned the effect of annealing on chromium-manganese steel2 and later3 constructed approximate sections of the iron-chromium-manganese equilibrium diagram. M. Schmidt and H. Legat14 even more recently studied this system, and their article and conclusions are of interest as representing an entirely independent study of a number of iron-chromium-manganese alloys. Koester's sections are shown in Fig. 1. The figures summarize the effect of manganese additions to iron alloys containing 5, 10, 15 and 20 per cent Cr as well as the effect of increasing chromium content on iron alloys containing 3, 8, 20 and 30 per cent Mn. These diagrams, within their composition limits, substantiated in some measure the results of our investigation. However, in our work some differences as regards the position of the mixed alpha-gamma fields were found as compared to Koester's work, and we were able to detect the presence of

Jan 1, 1938

By R. G. Hudson, H. W. Paxton

The activities of iron and chromium in their binary system have been measured by the Knudsen orifice technique. The system is close to ideal at 1200- 1250 C with slight positive deviations. The effect of this on the liquidus and solidus is discussed and these are calculated for two limiting assumptions. The vapor pressure of pure iron, pure chromium, and one alloy is compared with that obtained by the Langmuir free-evaporation technique. The results agree, indicating a vaporization coefficient close to 1. HERE are no reported data on the thermody-A namic activity of iron and chromium in the solid portions of the phase diagram. It is generally assumed'.' that the liquid solutions of iron and chromium obey Raoult's law. Chen and Chipman" have inferred that the liquid solution obeys Raoult's law. The minimum' in the solidus-liquidus curves for the iron-chromium system shows that there are deviations from ideality in either the solid or liquid or both. Because of the importance of developing reliable techniques for obtaining activity data in alloy systems at high temperatures and of the data so obtained, an investigation of the activity of iron and chromium in the binary at 1200-1250 C was undertaken using the Knudsen cell. Experimental The apparatus and experimental procedures used in this investigation were described in a previous paper." The various materials used for the construction of the Knudsen cell are listed in Table I. The metal used for the determination of the vapor pressure of chromium was 99.9 pet pure, obtained from A. D. Mackay, Inc. The iron was obtained as electrolytic grade from Fisher Scientific Company. The Fe-Cr alloys used are shown in Table 11. The largest error and controlling factor in the accuracy in the experiments reported here are introduced because of temperature uncertainty, which is estimated to be ±3 deg C. This introduces an uncertainty of 26 pet in the measured pressure. Experimental Results and Calculations The vapor pressures of pure iron and pure chromium were calculated from the measurements by the Knudsen equation3 on the assumption that only Cr or Fe atoms were present in the gas phase. For metal vapors, at the high temperatures and low pressures involved in these measurements this should be a reasonable assumption. Whitman" corrections for the cells were made. The data and results of pressure calculations are presented in Table I, and are plotted in Fig. 1. In addition the heat of vaporization at the absolute zero, ?E°°, has been calculated for chromium. These calculations are summarized in Table 111. The data used in these calculations are as follows kelley13 (F° - E°°/T ) Speiser, et al H (F° - E°°/T ) 010 where F" — standard free energy at temperature T It was necessary to calculate the total pressure above the alloys from the total weight loss W of the cell during a run, because of the fact that all attempts to collect and analyze the chromium and iron vapor effusing from the cell in the apparatus available failed. The failure resulted from the re-

Jan 1, 1959

Jan 1, 1958

By R. B. Walker, R. Palmer, L. C. Bryner

The purpose of this investigation was to further study some of the factors affecting the air oxidation of sulfide minerals. Data obtained from laboratory studies on the effect of temperature, concentration of iron salts, pH, and other catalysts on the biological and nonbiological oxidation of sulfide minerals are presented. The oxidation of copper sulfide minerals and subsequent leaching of the soluble copper has long been a profitable operation. The chief oxidizing agent is oxygen from the air. This reaction is influenced by a number of different factors such as temperature, light, hydrogen ion concentration, oxidizing agents, and various catalysts. Sullivan1 found that copper sulfide minerals are slowly oxidized by the air and that dilute sulfuric acid and iron (111) increased their solubility. At that time it was not known that bacteria were involved in the oxidation of the sulfide minerals. It has been shown that pyrite, molybdenite, free sulfur, and the copper sulfide minerals found in the waste rock dumps in Bingham Canyon, Utah, are largely oxidized by chemosynthetic autotrophic microorganisms found in the leaching streams.2-6 Similar organisms have been isolated in other mining areas7,8 and from the effluents from coal rnines.9 The following are some of the questions that have arisen regarding the mechanisms of the reactions involved in the leaching process. How dependent is the leaching operation upon the biological reactions? How does the temperature effect the biological and non-biological reactions? How does the concentration of iron (II) and (111) effect the rate of oxidation of copper (II) sulfide? Does the iron act as a catalyst? Does activated carbon act as a catalyst on the oxidation of sulfide minerals? What effect does the hydrogen ion concentration (pH) have on the above reactions? The purpose of this paper is to report the results of laboratory studies on these problems. EXPERIMENTAL The apparatus used in this investigation was an air lift percolator described in our earlier work.' The percolator consisted essentially of an air lift which enabled the leaching solution and microorganisms to pass freely through a suspension of mineral (substrate) in Ottawa sand. The air lift served the additional purpose of maintaining an ample concentration of oxygen and carbon dioxide in the nutrient (leaching) solution. (See Fig. 1.) The percolators were so constructed that they could be immersed in liquid constant temperature baths for temperature studies. The thermostats were controlled to +0.5°C. The reactions were all run in the dark. The percolators were charged with one to three g of mineral, dispersed in 100 g of Ottawa sand and 100 ml of nutrient or leaching solution. The sand was purified to remove traces of iron by digesting with concentrated hydrochloric acid and washng with distilled water until free from chloride. After drying, the sand was ready for use. The compressed air supply was regulated to 5 psi and bubbled through an aerator containing distilled water, which was maintained at the same temperature as the bath used. The air was filtered through cotton plugs to maintain sterile conditions. The tops of the

Jan 1, 1968

By J. A. Botin, K. H. Singh

INTRODUCTION The Alfredo underground mine is one of the three mining operations of Rio Tinto Minera, S.A., all near the community of Rio Tinto in Huelva province of southwest Spain. The other two operations are Corta Atalaya open pit (Pyrite ore) and Cerro Colorado open pit (Copper ore 1. Underground mining of Alfredo Mine for pyrites started in the nineteenth century and continued without interruption until 1979 when it was discontinued due to economical reasons. In 1972, a new project was started for the mining of copper bearing ores on the footwall of the pyrite deposit. This copper ore is locally named “Cloritas” and it forms a nearly vertical and tabular shaped orebody which forms an envelope at the footwall of the San Dionisio pyrite orebody. Mining of the Cloritas commenced in 1975 using cut and fill stoping. In 1977, the original project was completely revised which led to the introduction of a bulk mining system to achieve a planned production of 3,000 tonnes of ore per day. This paper covers the economic and planning aspects of the mine and discusses the evolution of the mining method for the Cloritas orebody. A GENERAL DESCRIPTION OF THE CLORITAS OREBODY The “Masa San Dionisio” (figure 1 ) is a massive sulphide orebody located in the town of Rio Tinto, about 90 kilometres west of Sevilla, Spain. Extensive vein-type sulphide mineralization exists in the volcanic host rocks of the Masa San Dionisio. Within this area of stockwork veins, there is a higher concentration of copper in the form of chalcopyrite in a zone adjacent to and paralleling the contact with the massive sulphides. This copper envelope is locally referred to as the "Cloritas Orebody” and the ore within it is called "Cloritas”. The main zone of the Cloritas orebody, (figure 11, is tabular and nearly vertical having a length of 375-400 m east-west, a thickness of 20-50 m north-south, and a vertical extension of 500 m from the surface. In addition to this area, there is a second less important low grade area called zone 2A located to the north of the main zone below 26 Level which, in some sections, is not fully separated from the main zone. MINING METHODS Mining in Rio Tinto area can be traced back to the Phoenecians and the Romans. Modern day mining started with the demand for sulphuric acid during the last half of the nineteenth century. By 1971, more than 33 million tonnes of pyrite had been mined out of Alfredo Mine, (San Dionisio Orebody), using labor intensive drift and fill methods and also by open pit method. During the last decade, underground mining of the pyrite had become uneconomic due to lower prices and a slackening demand for pyrite, and the underground mining operations for pyrite were finally stopped in 1979. In 1971, a major change in the long range mining plans for Masa San Dionisio was established. Between 1971 and 1975, underground mining of pyrites was progressively reduced while open pit extraction was increased in

Jan 1, 1981

By Oliver Bowles

AMONG mining men as well as in the popular mind the conviction has held sway that mining is pre-eminently a western industry. True it is that gold, silver, copper and other metals have made the States of California, Colorado, Montana, Utah. Nevada and Arizona famous. The prominence attained by these States as mineral producers is, however, not measured alone by the money value of the products of their mines. While the metals are without doubt indispensable in industry, the glamour of the precious metals, and the lure of copper, lead and zinc have given to their ore deposits a sentimental interest that often quite out-weighs their commercial importance. Today a great group of more commonplace minerals are finding a place in commerce and industry rivaling that of the metals, but there is little sentiment attached to them, and,. therefore, they attain relatively little publicity. This is the great group of the non-metallic minerals, exclusive of fuels and oils, including stone, sand and gravel, cement, lime, gypsum, asbestos, mica, phos-phate rock and many others. Almost unnoticed they have grown in production to almost unbelievable pro-portions. The estimated value of metal production for 1925 is given as $1,380,000,000, of the non-metals (ex-cluding fuels) $1,294,000,000. The non-metallic industries are not new, many of them date back almost to pre-historic times; but, as the greatest of them (on a tonnage basis) provides raw materials for the construction industries, it required the activities of the present age of construction to bring about their enormous development. Many of them enter manufacturing as well as con-struction. Non-metallic minerals constitute the back-bone of our great chemical industries. While construction and manufacture reach to all parts of the country their widest development has been in the great industrial centers of the eastern Seaboard and the middle West. Consequently the raw materials of mineral origin required for these great industries have attained a remarkable growth in the eastern half of the- United States. In compiling figures of mineral production for 1924, for which more complete data are available than for later years, the surprising fact is brought to light that the non-metallic mineral produc-tion alone of some of the eastern and middle-western States exceeds by a substantial margin the total min-eral production of some of the western States that have been classed as essentially mining States. Thus the non-metallic mineral production, exclusive of coal and petroleum, of the State of Ohio, was approximately $150,000,000; of Pennsylvania $175,000,000; and of New York $107,000,000. For the same year, 1924, the total mineral production of Utah was $84,357,000; of Montana $70,632,000; of Colorado $61,488,000; and of Nevada only $26,226,000. Even Minnesota, with its enormous iron ore production, reached only $107,845,-000, or a sum about equivalent to the non-metallic min-eral production of the State of New York.

Jan 8, 1927

By Elbert Rowland

THE widespread interest in the alloys of beryllium with copper is due principally to the fact that certain compositions show very favorable precipitation-hardening characteristics and are, in fact, the strongest nonferrous alloys known at the present time. Investigations have been conducted by Masing and Dahl and others on the physical characteristics of ternary beryllium alloys, in an attempt to produce precipitation-hardening effects with a smaller amount of beryllium than that required in the binary copper-beryllium alloys (2.0 to 2.5 per cent Be). The results of these investigations show that ternary alloys of beryllium with Cu-Sn, Cu-Al and Cu-Zn, among others, exhibit promising improvements in physical properties after precipitation-hardening treatment and, while the increases in properties obtained are not as high as those realized from the binary copper-beryllium alloys, excellent properties are obtained with beryllium contents averaging about one-half the amount required in the binary alloys. This paper presents the results of an investigation of the equilibrium relations of certain alloys containing copper, tin and beryllium. The alpha-phase boundary of the ternary system is given for alloys containing from 0 to 1 per cent beryllium. The equilibrium conditions beyond the alpha-phase boundary are presented for alloys containing up to 32 per cent tin and 1 per cent beryllium. The data were collected by means of

Jan 1, 1935

By D. W. Fuerstenau

Recently R. J. Charles1 showed that comminution of brittle or semi-brittle materials in batch operations is described more appropriately by a variable energy relationship than by the specific relationships proposed by Rittinger,2 Kick,3 and Bond.' That is, the value of n in the empirical differential operation which applies to crushing and grinding (Eq. 1) is variable. Independently, Holmes' developed an identical generalized equaton for size reduction. The experimental data of Charles and Holmes show that the value of n is determined by the material and the comminuting machine and is constant for a given combination of these two conditions. The general objective of the present article is to extend the Charles-Holmes concepts to continuous ball milling. The specific objective is to analyze the operation of a vibratory ball mill dry-grinding chromite in a continuous open circuit and to develop an equation for the comminution of chromite in this mill. Basic Principles: In a batch mill the length of time during which the material is ground is a direct measure of the energy expended on the material, except possibly for exceedingly fine grinding. However, in a continuous operation, the fraction of the total expended energy which is useful for grinding will vary according to feed rate and amount of material in the mill. If the amount of material within a continuously operating vibratory mill is low enough so that only part of the expended energy is used for grinding, the extent of size reduction at constant power input must depend upon the length of time the material is retained within the mill, namely, upon retention time. The following analysis pertains to a continuous mill operating under these conditions. The empirical differential equation that applies to the comminution of brittle materials is:" dE = -Cdx/x" [1] where dE is an infinitesimal energy expenditure, C a constant, dx an infinitesimal size change, x the particle size, and n a constant. For continuous grinding in an open circuit at constant power input, P, Eq. 1 must be written as (dtr)P = -C dx/x" [la] where dt, is an infinitesimal time during which a particle of size x is in the mill, and C' is a constant. A ground product never consists of particles of single size but always comprises a distribution of sizes. In comminution, the expenditure of energy causes a lateral shift in the size distribution.', ' " The general objective of any engineering study of comminution is to correlate the magnitude of this size distribution shift with the energy expended, the ultimate aim being to cause the greatest shift with the least amount of expended energy. Although a number of criteria can be used to measure this shift, Schuhmann's size modulus has been found convenient.' Mathematically, the Schuhmann size distribution can be expressed as follows:" y = l00(x/k) [2] or in differential form: dy = [F- xa-' dx ] K, where y is percentage of material finer than size x, a is a constant that determines weight distribution among particles of various sizes, and k the size modulus that denotes the theoretically maximum-sized particle in any size distribution. By considering the energy required to reduce an element of weight of material, dy, from size x, to size x, the element of time during which the material must remain in the mill at at power will be (dt..).= J'-Cax!(dy) [3] Summing up all the elements of weight from zero to 100 for a product that conforms to the Schuhmann size distribution yields C C f Cdx,\( 100«x°-'dx\

Jan 1, 1960

By Linn M. Farish

SOVIET RUSSIA reserves must be stupendous. In 1937 I. M. Goubkin placed the reserves of all categories it approximately 48 billion barren which was about twenty billion horn Is in excel:, of all the oil produced in the world since 1857. It is not unlikely in fact it is probable, that these huge stores of petroleum may ultimately be proven to exist within the present boundaries of the U.S.S.R. The size of the country is almost beyond imagination it is 2.7 times as big as the United States. Great sedimentary basins exist in all its different geological provinces, much of which are entirely untested and barely prospected. Oil in commercial quantities is actually produced from formations in every period from the Devonian to the Pleistocene. In the Emba region alone, 300 salt domes are known with an estimate of 700 still to be found. Only 22 of the 300 have been drilled and all showed oil. Of the 22 domes drilled six are now producing. There are 400 mapped structures reported in Azerbaijan

Jan 1, 1940

By P. H. Dudley

A Discussion of the Paper of Prof. Howe. (Bi-Monthly Bulletin, No. 14, March, 1907, pp. 169 to 274.) P. H. DUDLEY, New York, N. Y. (communication to the Secretary*) :-The characteristics of Prof. Howe's metallurgical papers are, that he is able, from the mass of confusing evidence on the subject, to make an analysis and present hypothetical and essential principles in concrete form for consideration and discussion. I can appreciate, from the practical side of the subject, the arduous labor of collecting and investigating the data that is essential to prepare the paper. Much of the data necessarily came from material of preceding years. of manufacture in which there was allowed time for chemical reactions of the recarburizer, and for the elimination of the oxidation-products before teeming the ingots. This condition gave a favorable tinge-element to free the metal from slag- and other impurities, but, in allowing the. ingot to cool before charging in the furnace, the time-element entered as a detrimental factor in the development of the pipe or shrinkage-cavities, which gave an ingot-structure deficient in soundness. The interpretations from such material must be made with due allowances for the methods of manufacture, and must be given proper weight, as general facts, in subsequent arguments. The difficulties under which investigators labor are not easily surmounted in differentiating between reliable and unreliable data incident to variables of methods of manufacture, chemical composition of the alloys of steel, mediocre practice and that of the highest state of the art. Modern practice and large outputs in Bessemer steel have reversed the effects of the time-element-by cutting short the chemical reactions of the recarburizer and the elimination of

Jan 5, 1908

JAmes E. Howard, Watertown, Mass.:—In connection with this paper, it is the desire of the Watertown laboratory to receive suggestions as to the lines of work and the particular direction along which the examination of the ingot-metal should proceed, and any suggestions so offered will be noted with care, and the tests conducted so as to embrace such features as it is thought desirable to have investigated. To me the question of structural continuity seems of para-

Jan 1, 1909

By C. W. Goodale

I. INTRODUCTION. In the summer of 1909 the Boston & Montana reduction department of the Anaconda Copper Mining Co. completed a new flue system, at a cost of about $1,100,000, and -is this includes the largest and highest chimney in the world, and some new features of flue construction, a description will be of interest. At the Spokane meeting of the Institute in September, 1909, a brief mention was made of this flue system, in discussing Mr. Brunton's presidential paper on the Progress of Metallurgy in the West, and a promise was given that when a long enough time had elapsed, so that operating results could be given, a paper would be offered. The smelting plant includes blast furnaces, MacDougall roasters, gas-fired reverberatories, and converters.

Jan 8, 1913

By Orville R. Lyons

THE removal of moisture from coal has been a coal-preparation problem ever since the first wet-washing preparation plant was placed in operation. Today, when most of the coal produced in the United States is wetted at the working face when mined, or is cleaned by wet methods, the removal of moisture is a necessity for any one or a combination of the following reasons; (1) to avoid freezing difficulties during shipment, (2) to increase the B.t.u. content, (3) to effect savings in freight costs, and (4) to so improve the coal that it may be used for specific purposes-for instance, in the production of briquettes or the production of metallurgical coke-or so that it can be treated by dry cleaning methods. In general, the amount of water retained by coal particles varies with the size-consist of the coal. Fine coal has a larger surface area per unit weight than does coarse coal, so its capacity for retaining moisture is proportionately greater. The removal of moisture from coarse coal is relatively easy, while the removal of water from minus 10-mesh coal or finer is a major problem, usually requiring an individual solution at each preparation plant. As a result, a multitude of methods and a variety of equipment have been designed to solve both general and specific moisture-removal problems. Definitions In order that misunderstanding may be eliminated insofar as possible, it is necessary to define the terms to be used. The moisture content of any given increment of wet, washed coal is made up of two parts, inherent and surface moisture. Inherent moisture has been defined in various ways and as yet no standard definition has been agreed upon. However, in general, it is considered as the moisture that is present in the coal in the bed. The important point to remember is that coal with any amount of inherent moisture, whether 2 or 20 per cent, will appear dry if there is no surface moisture. Also important is the fact that inherent moisture can be removed, in part, by air drying at atmospheric temperatures. Surface moisture is that attached to the surface of the coal particles or that retained in cracks and fissures other than capillary openings in the coal substance. Essentially, insofar as the bituminous coal and anthracite indus-

Jan 1, 1950

By Galen G. Waddell

Several years of rock-burst research conducted by the U.S. Bureau of Mines in cooperation with the mining companies of the Coeur d'Alene mining district, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem. A rock burst is the sudden, violent release of stored strain energy in rock by some mechanism of rock failure, generally accompanied by expulsion of rock with consequent damage to the mine. A burst may be audible for only a few hundred feet, or on the surface it may sound like a sonic boom miles away. A Dictionary of Mining, Mineral, and Related Terms, U.S. Bureau of Mines (USBM)* 1968yand defines a burst as Bureau "That phenomenon which occurs when a volume of rock is strained beyond the elastic limit and the accompanying failure is of such a nature that accumulated energy

Jan 1, 1971