Search Documents

By J. F. Haseman, J. E. Davenport

IN the brown rock phosphate fields of Tennessee there are large deposits of phosphate matrix in which quartz is a major constituent of the gangue, and which cannot be beneficiated by the conventional washing process to yield a concentrate of suitable grade for use in the electric furnace. A huge tonnage of high-grade phosphate concentrate is produced in the Florida pebble district from low-grade siliceous feed. However, the characteristics of the low-grade siliceous Tennessee ore are such that flotation under the conditions employed in treating the Florida ore1-2 results in inadequate beneficiation. INVESTIGATION OF FLOTATION METHODS Flotation has been used in Tennessee primarily to produce a concentrate of premium grade by moderate enrichment of a marketable grade of phosphate.3,4 A secondary use was to increase the recovery of phosphate from the fines (down to approximately 200 mesh) from medium-grade ores with a concomitant moderate increase in over-all grade.3,5 It was considered desirable to investigate methods of improving the grade of washed products from low-grade siliceous Tennessee ore when these products were substantially below the requirements for use in the electric furnace. The present paper describes the results of a laboratory-scale study of factors that affect the beneficiation of such siliceous phosphate ore by flotation. The primary objective of the investigation was to ascertain the conditions under which the ore could be made to yield a concentrate suitable for reduction in the electric furnace. It was assumed that a phosphate concentrate for electrothermal reduction should contain at least 26 pct P205 and should have a weight ratio of silica to lime of not more than 0.80. Since a concentrate of moderate grade can be used in the electric furnace, and since, as Grissom4 has shown in detail, the ore will not bear the cost of expensive treatment, the study of collectors was limited to the relatively inexpensive fatty acids. A secondary objective was to determine whether a portion of the phosphate could be recovered in a grade suitable for treatment with phosphoric acid to produce 45 pct superphosphate. The ore consisted of variably cemented sand interlayered with clay. The sand layers were composed of grains of quartz, phosphate, and clay embedded in a matrix of clay and phosphate. Some clay was finely disseminated in the phosphate grains. Little massive high-grade phosphate was present. The material used in the flotation tests was a washed sand that had been separated from the ore in a bowl classifier at the TVA phosphate-washing plant. The percentage composition of the sand was as follows: P205, 20; Si02, 40; CaO, 29; Fe203, 2; A1203, 3; F, 2.3. The particle-

Jan 1, 1947

Escalating energy costs and tough environmental standards were two major factors affecting the minerals processing area in 1978 For the most part, new startups and research and development initiatives were directed toward improving process dynamics, investigating alternative processing strategy, and lowering unit costs. In the flotation area, the trend to larger machines continued. Scientific investigation of the modeling and process control of flotation was apparent, as was the research and development of new flotation reagents.

Jan 5, 1979

CONTENTS PAGE Need for Research in Foundry Pig Iron. By Richard Moldenke. (With Discussion) 1 Carbon Characteristics of Copper-bearing Pig Iron. By W. B. Coleman. (With Discussion) 12 A Pig Iron, Low in Total Carbon, is in Demand for Use in Various Industries. By Enrique Touceda. (With Discussion) 24 Carbon in Pig Iron. By Ralph H. Sweetser. (With Discussion) 28 Second Session (Discussion) 37 Need for Research in Foundry Pig Iron BY RICHARD MOLDENKE,* WATCHUNG, N. J. So FAR as the quality of the product is concerned, the history of the production of pig iron for foundry purposes is one of constant retrogression. The steps in this deterioration began with cold-blast charcoal pig iron, then anthracite iron, coke iron; then gradually warm to hot-blast coke iron, with the charcoal furnaces also heating their blast to get greater tonnages, and finally the present-day hot-blast coke irons with scrap additions to the ordinary burden that, according to one European report, have gone as high as 65 per cent. Parallel with this quality retrogression is the enormous increase in furnace tonnages from about 15 to over 1000 tons per day in exceptional instances of modern practice. The key to this situation is economic pressure. The effect is a growing differentiation between furnace production for gray iron and malleable foundries and, for the

Jan 1, 1927

By S. Weinig, J. Winter

The grain boundary adsorption of solutes as a function of bulk concentration and solution temperature was studied using internal-frictimz techniques. From the variation of the cor-responding energy of activation for the Phenomenon, the inter-actior2 energy between a solute atom and a high-angle boundary was calculated. Interaction energies in the range of 0.3 ev were obtained, and were used to obtain the actual concentration of solute at the grain boundary. In corroboralory creel, studies the direct grain boundary contribution to the total creep strain was measured. It was found that the interface creep varied with the type and magnitude of the solute adsorbed. Subscribing to the theory of their being energetically favorable sites at the grain boundary for solutes of both Positive and negative size deviations, ternaries were investigated in Which solutes of both types were present. A marked increase in the resistance to grain boundary creep was manifested. THE major difficulty which has been encountered in investigations of the grain boundary segregation of solutes has been the lack of a sufficiently sensitive method of measuring the amount of adsorbed solute at the boundary. For the general case of a high-angle boundary, no direct method of measuring the adsorption at the boundary has been found to date. Internal friction has been used in several studies of grain boundary adsorption1-3 and although it is somewhat indirect, it was demonstrated to have the necessary sensitivity. In this investigation the authors have used internal-friction techniques in conjunction with a study of the grain boundary contribution to the total creep strain. As both parts of the investigation were performed on the same specimens it was possible to combine a highly sensitive technique with a somewhat more direct method in order to obtain information about the adsorption phenomenon. From internal-friction studies the rate of increase of the activation energy was observed to be a function of the difference in size between the solute and solvent atoms. It was proposed that if Gibbs' adsorption isotherm is considered, i.e., where r is the excess solute at the boundary, c is the bulk concentration, and ay/ac is the change in grain boundary energy with bulk concentration, then AH b/ac must vary in the same way as ay/ac and therefore In this way a relative measure of the grain boundary adsorption of solutes is directly obtainable from in-ternal-friction studies. If the previous work in the field of grain boundary adsorption of solutes is examined, certain apparent information is desirable if the phenomenon is to be understood. The most important questions that must be asked are as follows: 1) Is the adsorption of solutes at the grain boundary an equilibrium process? 2) Can the Mott model of the grain boundary be used as a basis of setting up an elastic interaction between the grain boundary and solute atoms? 3) Is it possible to obtain an exact measure of the excess solute at the grain boundary as a function of temperature and bulk concentration rather than merely a relative measure of the adsorption 4) Are the conclusions obtained from an indirect method such as internal-friction studies meaningful in considering gross grain boundary effects such as creep? EXPERIMENTAL PROCEDURE The material used in this investigation was Bureau of Mines "superpurity" titanium (79 Bhn—1500 kg

Jan 1, 1960

By H. K. Birnbaum

The termination of a twin lamella in the interior of a crystal requires accommodation of the strains at the tip of the twin which result from coherency of the twin and matrix. In zinc and magnesium crystals,

Jan 1, 1960

By John Chipman, Theodore B. Winkler

IN order to understand more fully the complexities of the reactions occurring between the liquid steel and the slag in the basic open-hearth steelmaking furnace, investigations in this country and abroad have turned to laboratory equilibrium studies. This paper is one of a series of reports on investigations being conducted at the Massachusetts Institute of Technology. The experimental work was completed early in 1942. The slag systems found in the basic open hearth are very complex, being made up of at least eight major components and as many others whose effect might be classified as minor. The first two papers of the series, by Fetters and Chipman,l,2 as well as the paper by Taylor and Chipman,3 dealt with the simplest possible slag system that would resemble those found in the basic open hearth-the slag system consisting of CaO-MgO-SiO2-FeO. (Taylor's rotating induction furnace eliminated the necessity of contamination of the slag by MgO.) Having arrived at some reasonable conclusions regarding the physical chemistry of the reactions between molten iron and the simple slags at equilibrium, the next step was to investigate more complex slag systems. The major purpose of the present investigation was to determine what factors control the distribution of phosphorus between molten iron and the more complex basic slags at equilibrium, and to what extent these factors are influential. The slags used contained CaO, MgO, Si02, FeO, Fe203, P205, MnO, A1203 and CaF2, but not all of the slag samples contained all of these components at one time. REVIEW OF LITERATURE Although a number of interesting papers have been published on the subject of dephosphorization of an iron bath, there are as yet no results from laboratory studies that give thoroughly reliable information on the dephosphorization reaction. Even for the supposedly simple Fe-O-P system involving iron-phosphorus melts and iron oxide-iron phosphate slags, the experimental results are contradictory and no formulas have been established that adequately fit the equilibrium conditions. The Fe-O-P system has been studied by Schackmann and Brings4' von Samson-Himmelstjerna,5 Oelsen and Maetz,6 Bischof and Maurer,7 Diepschlag and Schürmann,8 and Herty,9 and the results of their investigations appear in Table I. A number of different equilibrium constants and distribution ratios

Jan 1, 1946

THE decades immediately before and after the end of the nineteenth century (1890-1910) were a period of increased activity in mineral industry education. One reason for this, undoubtedly, was the rapid increase in mineral production in the decade 1880-1890; pig iron and copper production tripled; coal, lead, and zinc output more than doubled. Most of the other mineral substances followed the same general trend. Aluminum production began in 1886; petroleum output, which in 1888 was less than it was in 1882, almost doubled in the next three years. Gold alone showed no appreciable change until its discovery at Cripple Creek in 1891, followed by the Klondike in 1896, brought to boiling a public interest in minerals that had been simmering for some years previously. The first cyanide plant in the United States was erected at Bodie in 1892, and the first chlorination plant at Cripple Creek* the next year. Silver- lead smelting had already greatly developed, and the metallurgy of copper was almost transformed. The hearth area and smelting capacity of copper reverberatory furnaces more than quadrupled between 1878 and 1894; matte converters were first erected at Butte in 1884. Copper production of the United States in 1899 was 20 times that of 1872. While it was the increased technology used in mineral production that really made the field attractive for educated young men, undoubtedly they did not realize that, and were impressed mainly by the quantitative increase in output. Another factor was the increased general interest in engineering education; three times as many men took engineering degrees in the United States in 1890 as in 1880; 1892 showed almost a 56 per cent increase over 1890. Industry had come to recognize that technical training was worth while. The mineral industry lagged somewhat at first; the total number of mining degrees

Jan 1, 1941

By A. G. Metcalfe, A. Siede

The hardening of annealed copper during fatigue testing appears to be independent of the applied stress and to occur largely within the first 4000 cycles. Copper hardened by fatigue is more resistant to annealing than copper hardened by static means, and softens by a multistage process. Creep studies at 300°C show that copper hardened by fatigue also has greater resistance to creep than statically hardened copper. Some theoretical explanations are discussed. RECENT interest in the behavior of metals subjected to fatigue stems from observations of phenomena which could not be explained by current theories of the structure of metals. In 1953 Bullen et al.l showed that the hardening caused by fatigue at low stresses did not cause severe bending of the lattice as did hardening by static methods. This was later confirmed by Wood, 'and Broom and Ham.3 Clarebrough et al4 showed that as the stress level used in fatigue hardening was increased, bending of the lattice was introduced, eventually approaching that of metals deformed by conventional cold-working methods. The type of hardening introduced by fatigue has other interesting characteristics. Kemsley5 showed that copper fractured by fatigue at low stresses resisted annealing as compared to copper hardened an equal amount by static means. The work of Clarebrough etal, shows that the manner of energy release during annealing differs for fatigue-hardened and statically hardened metal in both magnitude and temperature range of release. In addition to hardening of the lattice, fatigue has been shown to cause softening in materials previously hardened by static methods,5 and also in age-hardened alloys.7 The superposition of a small fatigue stress on the static loading of high-temperature alloys has been shown to increase their resistance to creep.' The present work was an attempt to determine the relationship between fatigue hardening, resistance to annealing, and the creep properties of pure copper. EXPERIMENTAL PROGRAM The program described here was designed to answer three questions: 1) Can stress-cycle combinations well below the failure values give significant increases in hardness? 2) Does hardening, under different stress-cycle combinations, give increase resistance to annealing? And if so— 3) Does superior resistance to annealing confer superior creep properties over statically hardened material? Three-quarter hard OFHC copper was annealed in vacuo at 550°C for 1 hr to produce a strain-free material having a fine grain size and uniform hardness. (The standard deviation of the mean hardness of the annealed samples was less than + 1.9 Dpn). Annealing was performed after machining the fatigue specimens so as to avoid work-hardened surfaces. Jigs were used to avoid distortion. The fatigue properties of the annealed copper were determined using an accurately aligned Baldwin-Sonntag SF1-U machine operating at 1800 cycles per min. This limited the minimum number of cycles which could be examined to about 4000 stress reversals. Since failure resulted in specimen damage, hardness increase with number of cycles was measured by testing specimens fatigued to different fractions of the failure values. The results are shown in Fig. 1, and are superimposed on the S-N curve of the copper in Fig. 2. The resistance to annealing of fatigue-hardened material was compared to that of material hardened by uniaxial tensile straining. Specimens hardened to equal values by both methods were progressively annealed for 1 hr at temperature in vacuo. After each annealing treatment the hardness was measured using a Leitz Durimet hardness tester with a 500-g load. At least five tests were made for each hardness determination. The standard deviation for individual specimens varied from 0.26 to 1.48 hardness points. The results are shown in Figs. 3 to 5. The discontinuous nature of the annealing process has been brought out by drawing idealized curves through the data points. This can be justified by the consistency of the results as well as by general agreement with results of Kemsley.5 The creep resistance of fatigue-hardened and

Jan 1, 1960

By K. G. Davis, P. Fryzuk

A study has been made of the effect of undercooling on the grain structure and solute distribution in small ingots of pure bismuth and of a 100 ppm Ag in bismuth alloy. Autoradiographic evidence shows that in undercooled melts a network of dendrites is formed throughout the melt immediately after nu-cleation. At large undercoolings the dendrites are very thin and closely spaced. The origin of the observed grain morphology can be explained on the basis of information about the mode of solidification revealed by the impurity substructure. WHILE a great number of studies of nucleation in undercooled molten metals have been made, comparatively little attention has been given to the mode of solidification from melts with large undercool- ings. Colligan and Bayles1 and Walker2 have measured the rate of advance of the solid-liquid interface in undercooled nickel melts, but the morphology of the solidifying material remained a matter of speculation. Fehling and Scheil3 have described the grain structure in ingots formed from undercooled melts of nickel, palladium, and copper, and a series of Ni-Cu and Ni-Pd alloys. At small undercoolings, equiaxed structures are observed, the grain diameter tending to increase as the temperature of nucleation is lowered. At greater undercoolings, a columnar structure is developed, while with still further undercooling there is a smaller grain size incorporating rather coarse subgrains. All-bright and Colligan4 examined the grain structure shown by ingots solidified from melts of nickel and of Ni-Ag alloy at an undercooling of 105°C, and concluded that considerable grain growth had taken place after solidification. The object of the present work is to correlate the mode of solidification from undercooled melts with both the grain structure and impurity segregation, using tracers to examine the latter.

Jan 1, 1965

By L. C. Raymond

Valuations in the mineral industry differ from those of other enterprises because mines and oil wells have a definite life so cannot be considered a perpetuity. This requires that in any mineral-property evaluation the recovery of invested capital is necessary during the life of the property. Capital write-offs for nonextractive industries are assumed to be continuously plowed back to sustain the operation and produce yields on the capital invested. The extractive or mineral industry, however, generally attempts to return to the investor both interest and principal during the life of a property. Normally this is done currently and the dividend includes both items. Where the mineral property possesses large reserves and the life factor approximates a perpetuity, the return on investment is generally comparable to that of industrial stocks. The valuation of a mineral property, at best, is based on educated estimates and judgment factors. This is particularly true as it relates to estimating selling prices over a long term or assessing the quality of management. Also, it is possible to make various assumptions as to rapidity of working out the deposit, varying time for start-up of operations, varying earning rates, so as to obtain different results with the same basic facts. Thus it is not surprising that two engineers, irrespective of their abilities, may not agree exactly even when given the same facts, but their results should be close enough to be used in establishing a fair value for trading purposes. The valuation is no better than the source of basic data and the soundness of judgment factors. Fundamentally the basic principles of mineral valuation are similar for base metals, sulfur, oil, or any other mineral. Each mineral, however, requires an engineer to have a knowledge of such factors as its occurrence, distribution, mining and processing methods, and marketing problems in order to gather and analyze all the facts and data that have a bearing on the earning potential of the property. Present Value of a Mineral Property In essence the present value of a mineral property is a sum of money in today's dollars that future income from the property are worth. It differs from the total anticipated earnings by the amount of the interest that the unrecouped investment could be expected to earn during the period of recoupment. Thus, if one could accurately estimate what a mineral property will earn during its life, after deducting all operating, administrative, capital, interest, and tax charges, the determination of present value would be a relatively simple mathematical calculation. Normally, where the expected life of the mineral property extends beyond 20 or 25 years, the discounted value of earnings beyond this period is relatively small. The petroleum industry generally discounts the annual cash flow of an operation rather than earnings since, for tax-saving purposes, earnings are kept

Jan 1, 1976

By M. R. Geer, J. D. Davis, H. F. Yancey

ALTHOUGH the mechanical cleaning of coal is carried out at plants on the surface, preparation is actually begun at the face in the mine. Here the character of the coal and the amount, character, and distribution of the impurities within the bed may be seen. Blasting methods, dust-allaying procedures, location of mining cut with respect to bands of impurity, and the practice of discarding segregated impurities underground, all have an important bearing on the successful operation of surface cleaning units. The most important single characteristic of both coal and its associated impurities from the standpoint of cleaning is specific gravity. Other characteristics related in one way or another to the preparation , of coal are rank, petrographic composition, structure and hardness, and friability. These and still other coal properties are discussed in the first section of this chapter and impurity characteristics in the second. COAL CHARACTERISTICS RELATED TO PREPARATION Rank As a result of work done over a period of several years by committees of the American Society for Testing Materials and the American Standards Association, standard specifications are now available showing the 'classification of coals according to rank and quality of grade.' The term "rank" expresses the degree to which the original coal-forming material has been changed by metamorphism through successive stages from peat to anthracite. Table 1 shows the classification of coals according to rank as devised by the committees of the organizations mentioned. The basic scheme of classification for the higher-rank coals is according to

Jan 1, 1943

By P. Payson

INTERGRANULAR corrosion in corrosion-resistant chromium-nickel steels has been widely discussed in the last few years. So far as the author knows, nothing has been published which definitely shows that this tendency can be eliminated, although suggestions have been made that a remedy is possible if certain specifications are satisfied. Strauss, Schottky and Hinueber1 suggested an increase in chromium content to an extent that would prevent the impoverishment of chromium on carbide precipitation sufficient to cause impaired corrosion resistance in the matrix. Pilling2 suggested an increase in nickel, so that the stability of the austenite matrix would be increased. Aborn and Bain,3 say that "intergranular attack-may be eliminated by preventing carbide precipitation (e. g., by lowering the carbon content or somehow raising its solubility) or by precipitating it permanently under conditions which will not remove chromium from solid solution so drastically at any points." In a later paper Aborn and Bain4 state that many different metallic elements, tungsten, vanadium, copper, aluminum, molybdenum, titanium and zirconium, have been added in small per-centages to increase the stability of these alloys, but that it has been reported that according to the copper sulfate test these added elements act only to retard the intergranular corrosion, and that increased nickel and chromium contents have similar effects. Newell5 showed that the lower the quenching temperature before reheating, the less severe was the intergranular attack.

Jan 1, 1932

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By C. R. Hayward

CARLE R. HAYWARD.-I do not want it understood that I think that the conclusion that the time of tempering temperature is immaterial has been definitely proven, but since these are the first definite figures put out, I thought before continuing on more work ourselves, it would be well to present them as progress and for information. J. A. MATHEWS, Syracuse, N. Y.-I think that if Prof. Hayward would consult the paper of Profs. Barus and Strouhal,1 1885, he would find about 250 pages, mostly figures, on this subject, in which they investigated the tempering effect by electrical and magnetic methods. There are so many figures in the paper that it is very difficult reading. One point particularly brought out was that even at a low temperature, such as the boiling point of alcohol, about 60° C., there is a tempering effect, increasing up to 4 hr. One reason they obtained those results, with which the present authors are at variance, was that they started with a high-carbon steel which hardens thoroughly, whereas the steel Prof. Hayward and his collaborator used was a comparatively mild steel which does not take a great deal of hardening. About 3 years ago Mr. Stagg and I published 2 a few figures bearing on the same subject, but we used .a low-carbon alloy steel of high tempering qualities and found a great deal of improvement, particularly in ductility, by continuing the drawing up to 4 hr. We used a chrome-vanadium steel showing after heat treatment 250,000 tensile strength. On short drawing, we got almost no ductility, but by continuing to 4 hr., we raised it to 12 per cent. I believe Prof. Hayward's results are due to using comparatively mild steel, whereas Prof. Barus used drill rod and carried out a, wonderfully exhaustive

Jan 4, 1917

By AIME AIME

THE Tuesday afternoon session", H. A. Bedworth chairman and T. S. Fuller, vice-chairman, was opened with D. J. McAdam, Jr.'s paper entitled "The Influence of Cyclic Stress on Corrosion." This paper dealt with the influence of cyclic stress on corrosion of alloy steels, corrosion-resisting steels, monel metal and aluminum alloys. The paper was discussed by T. S. Fuller, who pointed out that steels under stress corroded more than unstressed steels when subjected to steam.

Jan 1, 1930

By E. B. Spice

Although much may be learned about the economics of cold weather operations by studying successful mining ventures in southern and central Canada, it is the purpose of this article to extend the study by considering only permafrost areas. Geographically this means most of the country north of the 60th parallel. In this area, at the present time, only five Canadian companies are carrying on routine and successful mining operations on a year-round basis. However, there have been some score of unsuccessful ventures, and a number of properties in the development stage show promise of being producers. Problems of cold weather are worthy of study. It may be pointed out that successful mines in this area face problems of isolation and costly transportation as well as cold weather. To reach valid conclusions, consider the development of a mythical mineral deposit located on the 65th parallel in the heart of the barren lands; problems of isolation and transportation will be ignored.

Jul 1, 1956

By L. L. Oriard

In order to predict the influence of blasting on slopes, one must first understand the action of explosives, the manner in which rock is broken or displaced, and how seismic waves are transmitted, and the nature of these seismic waves. In this paper, the author describes the action of high explosives on rock masses, beginning at the source of the explosion, extending through the zone of rupture to a distance where only elastic waves of low energy persist. The paper describes the relationships between explosives charge quantities and distances, including the character and intensity of the seismic waves in various types of terrain. In looking at the analysis of slopes subjected to seismic waves, it has been common practice to assume a simplified model in which the anticipated acceleration is applied horizontally to the slope as an equivalent static force, or a model in which there is a rigid base subjected to mechanical shaking. Such models do not accurately portray blasting activity taking place within or near the slope in question. In dealing with blasting effects, it is important to under- stand seismic wave types, wave lengths, attenuation and transmission paths, as well as vibration intensity. In most cases, those slopes that are the least stable under static loading will also be the least stable under dynamic loading, although there may be rare exceptions. Thus, the more that is known about a slope statically, the better will be the assessment of it dynamically.

Jan 1, 1983

By N. H. Emmons

An interesting development of copper blast-furnace construction has been brought about in adapting the blast-furnace to be a "burner" for sulphuric acid making. When the Tennessee Copper Co. first decided to construct an acid-plant, the standard type of brick-top furnace, supported by structural steel, was the only one in use at its plant. All the tests for temperature and strength of gas had been made on these furnaces, and had been satisfactory. When, however, the acid-plant was put on the flue, and the flue had to have a damper put in it to force the gas into that plant, troubles began. The furnaces were fairly tight, and for a few months the work was quite satisfactory. Fig. 1 shows the old type of furnace-top used at the start. It was soon found that this top would not stand the temperatures, particularly when dampered back, as was necessary to force the gas into the Glover towers. The structural steel, of which the furnace skeleton was constructed, warped and twisted so badly that it was not safe to use the furnaccs. This effect is shown by Fig. 2, which is a photograph of old No. 4 furnace, after the brick-work had been removed. It became apparent that a new type of top mas necessary and the engineering force was started on the design of a new furnace-top, with the result that a low top, with brick-lined flues at each end below the feed-floor, leading to the main concrete dust-chamber, was constructed. This furnace, No. 7, is shown in Fig. 3. The charging-doors are made of cast-iron sections, three sections to a door, and three doors to a side. A door to the furnace was made of east copper, but the heat was great that the copper bent readily, due to the jarring of its

Jan 1, 1911

By Raymond E. Birch, Oscar M. Wicken

THE mineral magnesite, formerly the source of nearly all magnesia, now shares this role with brucite, dolomite, and the world's natural and artificial brines. The mineral magnesite is the normal carbonate of magnesium, MgCO3, composed when pure of 47.6 pct MgO and 52.4 pct CO2. It is one of the calcite (CaCO3) group of rhombohedra1 car- bonates, which also includes dolomite, CaCO3.MgCO3, and siderite, FeCO3. Magnesite does not form an isomorphous series with calcite or dolomite; consequently, these lime-bearing carbonates commonly present in magnesite deposits are there only as mechanical mixtures. Magnesite and iron carbonates form a continuous isomorphous series and therefore are inseparable mechanically. The variety of magnesite known as breunnerite is an isomorphous mixture of iron and magnesium carbonates. Magnesite may be either crystalline or amorphous (cryptocrystalline). The former, which includes breunnerite, is often termed spathic magnesite. Crystalline magnesite varies from finely to coarsely crystal- line in texture and has a hardness of 3.5 to 4. The color is white, yellowish, blue-gray to drab, red, pink, black, or mottled. It is seldom found pure but usually contains variable amounts of iron, lime, silica, and sometimes manganese. The color cannot be used as an index of purity. The cryptocrystalline variety is perhaps the more common type but the crystalline variety usually occurs in larger deposits. The amorphous type is fine grained and compact, showing no cleavage. It is usually snow white but sometimes is light to pale orange yellow or buff, owing to impurities. The fracture is conchoidal to uneven and the hardness 3.5 to 5. Silica may be present as inclusions of serpentine, quartz, chalcedony, or other minerals. The lime and iron contents are usually low. In general, amorphous magnesite is somewhat purer than the crystalline variety. The specific gravity of cryptocrystalline magnesite is 2.90 to 3.00. Pure crystalline magnesite has shown a specific gravity of 3.02 but iron

Jan 1, 1949

Jan 1, 1916