Search Documents

By R. A. Wood, R. I. Jaffee, H. R. Ogden, D. N. Williams

Strain-induced porosity has been found to occur in titanium and other materials at tensile strains greater than the uniform elongation of the material. Porosity in titanium increases with increasing strain and temperature, being most severe at 300° to 800°F. Strain-induced porosity is believed to be a normal part of the mechanism of deformation in ductile materials. DURING the past few years there have been numerous references to the occurrence of voids in laboratory test specimens of metals subjected to strain.l-7 These voids have been referred to as intercrystalline cracking, strain-induced porosity, intergranular cav-itation, voids, and porosity. They appear to occur at grain boundaries or interfaces, and are generally associated with large amounts of strain and have been found mostly in creep specimens and to a lesser extent in tensile specimens. Because the phenomenon does not occur unless the material has been strained,

Jan 1, 1960

By Thomas T. Read

I. INTRODUCTION. WHEN so much has been written upon a subject on which so little definite information is available as upon this, some reason must needs be assigned for adding to the volume of literature. A sufficient reason is found in the probable great future importance of China as a producer of mineral wealth. The present undeveloped state of mining in the Empire is due to many causes, among which the most important are the relatively simple needs of the population, the lack of transportation-facilities, the inelastic regulations governing the industry, and the superstitious reluctance of the people to make excavations which might disturb the spirits of the earth and air, or of ancestors. Iron is the metal most in demand, yet the needs of the population, until recently, only made necessary a production of approximately 0.5 lb. of iron per capita per year. The present annual production of iron for domestic consumption, in the United States, is nearly 600 lb. per capita. The curious state of development of transportation in this interesting country has been a greater handicap upon the mining industry than upon any other. The point upon which it hinges is the absence of a road-system. Except for a few military roads, now almost impassable, there are no roads in China; that is to say, there is no land which is set aside as a right of way, belonging to the commonwealth. Throughout the agricultural districts, generally speaking, the entire area is in private ownership, and the lines of travel are between fields. There is a constant struggle for existence between the owners of the land and the traveling public, with the natural result that the so-called roads usually

Mar 1, 1912

By E. C. Olsen

This paper describes the unusual hazardous conditions encountered in mining thick, inclined coal beds under heavy cover in Carbon County, Utah. This description includes heavy roof conditions, sloughing ribs, steep pitches, and severe bouncing experience. Emphasis is placed on the top bench system of mining and development in the top half of a 16-ft seam, under the roof rock, which is bolted, and the recovery of the bottom coal on retreat; success of bolted roof and ribs; and shuttle car haulage on pitches up to 25%. The use of protective cages for operators of face equipment, the guarding of belt conveyor systems to prevent injury associated with deliberate entry, and the positive lockout of electrical equipment is described and illustrated. Most coal mining areas of the Western United States are characterized either by thick beds, steep pitches or heavy cover. Individually, each of these may present inherent safety hazards that in- fluence mining. When all are met at one location, the combined effect is to make the safe operation of the mining property a challenge to management. These combined conditions are met in the coal mines of the Columbia-Geneva Steel Div. of the United States Steel Corp., in southeastern Utah. This coal bed measures up to 16 ft in thickness, the pitch is as much as 25% and mining is under a cover approaching 3000 ft. The Sunnyside coal bed is found in the Book Cliff Mountains, a great escarpment extending from west of Castle Gate, Utah, some 180 miles to Grand Junction, Colo. West of Green River, Utah, the Book Cliffs swing sharply to the north because of the domelike uplift of the San Rafael Swell to the southwest. It is in this northerly extension of the Book Cliffs that the Sunnyside coal in the Blackhawk Formation of the Mesa Verde Group, Upper Cretaceous Age is found. The strata are transected by numerous faults with from a few inches to as much as a hundred feet of displacement. All of these faults have had some effect on the mining operation, either in roof control or, in the case of major faulting, the pattern of mine development. MINING PRACTICES Mining has generally been confined to the Lower Sunnyside Seam which measures from 7 to 16 ft in

Jan 1, 1963

By Karl A. Bauer, Cornelis Bezemer

The deposition of calcium carbonate scale on surface and subsurface production equipment creates an operation problem in many oil fields. The formation water in which the carbonate-scale-forming components are initially dissolved becomes supersaturated with calcium carbonate as a result of the drop in pressure during production. The continuous flow of a supersaturated solution through the production equipment results in the growth of a dense layer of calcium-carbonate crystals. For a scale layer to be built up, the supersaturated formation water should contact the walls of the production equipment. The tendency for scale to be deposited, therefore, will be low, if the crude has a low water cut and if the water is finely dispersed in the oil. A scale problem will occur, if at a high water cut part of the water is present as free water. The rate of scale deposition will then be approximately proportional to the rate of free water production. Depending upon where the formation water becomes supersaturated, scale may be deposited in the flow line only, in both flow line and tubing, and in some cases even in the perforations and in the formation near the wellbore. In the South Sumatran fields (Indonesia) the main difficulties encountered due to the deposition of calcium-carbonate scale have been restriction of flow through tubings and flow lines, wear and abrasion of plungers and liners, and stuck plungers or wellhead valves. So far, the only methods of combating the *Presently associated with Brunei Shell Petroleum Co., Ltd.. Seria. scale problem have been routine acidizing and additional well pulling. As for the pumping wells, it was estimated that some 50 percent of the total well-pulling effort was directly attributable to scale deposition. The most promising alternative was to prevent the deposition of calcium carbonate scale by means of chemicals. Inorganic polyphosphates such as sodium hexametaphosphate and trisodium polyphosphate are known to retard the formation of scale by the "threshold action". They are adsorbed on specific faces of the crystal nuclei and thus prevent crystal growth, thereby stabilizing supersaturation. Polyphosphates are effective at very low concentrations ( a few ppm), and far less than stoichiometric quantities are required to keep the scaling ions in solution. Recent investigations on barium sulfate scale1 have confirmed this mechanism. The types of polyphosphate mentioned can be applied as concentrated aqueous solutions either squeezed into the formation, lubricated down the annulus or injected via macaroni string. Several squeeze jobs with polyphosphate solutions have been carried out in the South Sumatran fields, however, with disappointing results. Lubrication down the annulus and injection through a macaroni string were not considered attractive in this area because of the kind of equipment and the degree of supervision these techniques require. Polyphosphates are also available in a granular, glassy form, which, in contrast with the readily soluble types already mentioned, show an extremely low

Jan 1, 1970

By R. W. Stahl

Employees and dollars are necessary to all enterprises and any force, such as fire, which destroys either, can bring very serious consequences, including business failure. Since everyone acknowledges the necessity of conserving human life, we will devote most of our paper to the economic factors involved. A coal-mine fire is considerably more difficult to combat than a fire in a surface building because of the combustible surroundings in the mine, the explosive gases emitted from the coal, the suspension of explosive dust when mine timbers burn and the unsupported roof falls, the limited space in which approach to the fire can be made, and the limited avenues of escape. A survey of coal-mine-fire protection indicated that a rather low value was being placed on property and equipment. This prompted comparison with other industries. The comments made in this comparison are not intended as an indictment of the coal industry, since we do have mines that are well protected against fire, but the comments on conditions at the mines visited are factual and may help others to improve similar conditions. SURVEY PROCEDURES Plants of the steel, aluminum, rubber, chemical, and petroleum industries were surveyed, and all facets of the fire-protection scheme were covered. The industrial plant invariably had four times as much water readily available for instant use than the mine. In many mines where water is available, no equipment for applying it is provided, such as hose, nozzles, and adapters, so that time is lost in collecting this equipment. (See Table I.) EXTINGUISHERS Many more and generally larger portable extinpishers are available at the plant as compared to the mine. The extinguishers are generally placed nearer to sources of danger. In addition, respiratory protective equipment is always available at strategic points in plants but only in a few mines. (See Figs. 1 and Table 11) INSPECTING AND TESTING EQUIPMENT Plant water facilities are checked weekly and flushed at 6-month intervals, and hose is pressure-tested at least yearly; some mines check water yearly, but hose is not tested unless used. Fire extinguishers are inspected weekly in plants and completely overhauled yearly; one mine had monthly checks and overhauls only after use. FIRE BRIGADES AND TRAINING Every plant had designated fire-fighters and some complete full-time brigades; at one mine a chief mechanic was designated as being in charge of fires, and other depended entirely upon officials who might not be familiar with the equipment. COST OF FIRES AND PERCENTAGE OF CAPITAL INVESTMENT IN FIRE PROTECTION The direct cost of recent mine fires ranged from $128,000 to $240,000; indirect costs, such as lost tonnage, idled equipment, lost orders, and the like might run the cost to over $500,000. (See Figs. 2 and 3).

Jan 1, 1961

By L. M. Kaas

Production planning techniques, particularly a production scheduling model are proposed for use in taconite mining in Minnesota. Applications of the scheduling model, on a two-year mine plan, which evaluates the equipment involved, are detailed. Data and tables are included. INTRODUCTION Fifty years ago Walter Swart, a mining engineer investigating the Minnesota taconites for the Jackling interests, made this report: "There is no doubt in my mind that this taconite mining is a game worth playing and that it can be played to a successful finish. It seems now only a question of men, money, methods and details."' The prosperous industry envisioned by Swart and other taconite pioneers is today a reality. Its growth has been spurred by technological advances in mining and beneficiation, depletion of natural ore reserves, and improvement of the economic climate. However, the massive problems that were solved to make this development possible are only a foreshadowing of the questions of "men, money, methods and details" that will be encountered in the future. The increasing demands for higher quality taconite pellets have already forced producers to examine better methods of quality control for their operations. THE NEED FOR PRODUCTION SCHEDULING The maintenance of fairly constant crude ore characteristics is of major importance to mill quality control. Through careful mixing of ore from storage bins, the concentrator staff can partially reduce the deviations of the feed analysis from the analysis desired. However, the limited effectiveness of bin mixing systems has caused some mining companies to utilize large capacity blending piles to reduce grade variations. Although the analysis of material being reclaimed from such a pile is relatively uniform, raw materials still must be scheduled from the mine into the pile in such a manner that the average analysis of all material is close to the feed analysis prescribed by the mill. PRODUCTION SCHEDULING MODEL Minnesota taconite mining companies have used three analyses to estimate how a certain ore will react to concentration. These factors are the crude magnetic iron content of the ore, the iron content of the plant concentrate produced from the ore at a standard grind, and the grindability index of the ore. The actual laboratory tests used to determine these factors have been described by Apuli.2 These data are obtained from analysis of diamond drill cores, and are the established criteria used by mine planning engineers to formulate taconite production schedules. Variations in the grade of mine output should be controlled by any production scheduling system. However, to be truly practical, production scheduling methods must also consider many of the less tangible variables that affect mine operation. These include pit layout, available equipment, and ownership of ore leases. The number and scope of the variables inherent in this type of mine planning suggested that a computer simulation could be used to solve the problem. The preparation of information for use with a computer simulation program was the initial phase of this project. Meaningful data was developed from logs of diamond drill cores. Analyses were related to their respective areas of influence by means of mine maps, Fig. 1. The three assay variables and tonnages for each area were punched on cards. In addition to these values, a location code number was punched in the first eight columns of the cards. This code is explained as follows: Column 1 Bench number Column 2 Quadrant location as determined by mine reference lines Columns 3-5 East-west coordinate Columns 6-8 North-south coordinate The heart of any simulation techniques is a well engineered mathematical model. To develop a model for taconite production scheduling, the relationship between the three assay variables had to be established. Because changes in each analysis factor affect the mill circuits in different manners, a weighting system was used to determine the relative im-

Jan 1, 1967

By J. H. Swisher

An experimental study has been made of the possible mechanisms for foam stability in the system CaO-SiO2-Cr2O3, where Cr2O3is the foaming agent. The degree of lowering of surface tension by Cr2O3 was determined at 1600 "C for high -silica melts. Measurements were also made of foam stability under standardized conditions. The results of the two sets of measurements then were correlated by applying the Gibbs and Marangoni theories of film elasticity. It was demonstrated that the Marangoni elasticity effect is probably the largest single contributor to foam stability, although the high uiscosity of' silicate melts makes some contribution in controlling the rate of drainage of liquid from bubble lamellae. ThE tendency of metallurgical slags to foam has frequently been observed during steel-refining operations. In the open-hearth furnace,this tendency is considered undesirable because it slows down the rate of heat transfer from the burners to the molten-metal bath. On the other hand, it is sometimes desirable to have a "foamy" slag in the basic oxygen converter.' A more effective blanket over the steel bath is made by a "foamy" slag, and loss in yield of metal due to splashing is minimized. In addition, a flush slag can be removed more easily in this condition. Since slag-foaming problems in the field have been attacked largely on an empirical basis, it appeared desirable to obtain a better basic understanding of the mechanism of foam stability. The experimental work was directed almost entirely toward the behavior of Cr2O3 as the foaming agent in CaO-SiO,-Cr2O3 melts. In the first stage of the investigation, the degree of lowering of surface tension by Cr2O3 was determined at 1600°C. The second stage consisted of measuring foam stabilities under standardized conditions. The two sets of experimental results then were correlated by applying various theories of foam stability. For convenience in interpreting the surface-tension and foam-stability results reported here, a portion of the CaO-SiO2-Cr2O3 phase diagram2 is reproduced in Fig. 1. EXPERIMENTAL 1) Surface-Tension Measurements. Very little information is available in the literature on the lowering of surface tension of slags by foaming agents. Kozakevitch 3 mentioned that the addition of 1.5 pct Cr2O3 lowered the surface tension of FeO slightly. In another system, some data on the lowering of surface tension of foaming slags by P2O5 were reported by Cooper and Kitchener.4 The technique used for the surface-tension measurements was the maximum bubble-pressure method,' using a single tube immersed to various depths in the melt. This method has been used extensively in high-temperature systems, such as in liquid metals, slags, and glasses.6,7 It has the advantage that the contact angle between the liquid and the tube material need not be known. The equation used for calculating surface-tension values from maximum bubble-pressure measurements is the Schroedinger equatioq5 which can be written as follows:

Jan 1, 1964

By Robert Thomas

DURING the past 20 years the advantages of reinforced concrete as a substitute for timbering in so-called permanent mine openings have been fully recognized, and its use has become almost general practice in the larger mines. The term "permanent mine openings" is used advisedly and is assumed to embrace such openings as ventilation shafts, material shafts and main hoisting shafts, with their adjacent stations, ore pockets, etc. In the concreting of such openings, the actual cost as compared with that of timbering has been of secondary consideration, the support of large openings, elimination of fire hazards, and prevention of inter-ruptions to production being the primary objectives. The ultimate economy, however, of lining such openings with concrete when they are to remain in use during the entire life of the mine, and especially when they are in bad ground, will seldom be questioned. During this 20-year period there have appeared in engineering publi-cations a number of interesting articles on the use of concrete in mines, nearly always describing some specific project of major proportions, such as the concreting of ore pockets, large stations or main hoisting shafts. Such articles are unquestionably of interest, since the projects require considerable engineering thought, not only in the method of excavating large openings, but in their engineering design as well. Concreting of main hoisting shafts, particularly when this is done with the least possible interruption to production, provides some interesting problems. The concreting of haulage drifts of the dimensions commonly found in mines, on the other hand, soon develops into a routine operation, there-fore it is with some hesitancy that the author attempts to prepare an article on this subject. The writer can recall only one article on the concreting of mine haulageways, although several articles have been written concerning the concreting of tunnels considerably larger in dimensions than those required in general mine practice.

Jan 1, 1936

By R. W. Drier

THE conductivity of copper wire is of prime importance to the electrical industry and consequently to the copper refiner and wire manufacturer. Annealed copper wire has a higher conductivity than hard-drawn wire, but, on the other hand, its tensile strength is lower. In an attempt to explain the reasons for these changes in property or at least to study the conditions existing in these two types of copper wire, the experiments described here were carried on in the Department of Metallurgy of the Michigan College of Mining and Technology. This is only a partial and preliminary report on some of the work done to date on a research program of which the object is an intensive study of copper. It is offered with the hope that, though it is not an exposition of the most rigorous of conclusions, the general trend of inferences which may be drawn will be of value and interest.

Jan 1, 1929

By M. V. Mielke, R. E. Hagen, R. L. Bennett

FINE IRON ORES, and concentrates such as those produced from taconite, must be converted to lump form by some process of agglomeration before they can be used effectively in the blast furnace or open hearth. At the present time, four major processes for agglomerating these materials are being used on a commercial scale: sintering, nodulizing, pelletizing and briquetting. IN 1945 U. S. Steel Corp. through its subsidiary the Oliver Iron Mining Div., drew up tentative plans for an agglomerating plant on the Mesabi Range which would include a nodulizing kiln and a sintering machine. The purpose of the plant was two- fold: during its initial operation it would provide data on agglomeration of high grade ore fines, and would help relieve the shortage of ore for open hearth charging. Subsequently, it would be available for agglomerating taconite concentrates. While operating on fines screened from direct ore, it was planned to develop techniques and personnel so that a workable plant would be ready to handle taconite concentrates when the time came.

Jan 1, 1954

By J. E. Warren, J. H. Hartsock

An asymptotic solution to the equation that describes the flow of a slightly compressible fluid in an infinite porous medium has been used to estimate the interaction between two adjacent wells producing from a common reservoir. A direct method for approximating the interference time defined by Stevens and Thodosl has been suggested. An alternative definition for the time of interference, based on the minimum pressure change in the interference region, has been proposed; also, a direct method of determination has been prescribed. Examples have been employed to illustrate the use of both methods.

By E. S. Wheeler

The rapid increase in the use of monel metal and malleable nickel in the form of sheet, rod and tube has resulted in a similar increase in the demand for these metals in the form of castings. These castings range in size from small valves and pipe fittings weighing a few ounces to large centrifugal pumps, gate valves and marine propellers, some of the last weighing as much as 24,000 lb. A group of such castings is shown in Fig. 1. A large nickel agitator is shown in Fig. 2. Monel metal castings are widely used in accessories for steam power plants and in a variety of chemical plant equipment where the corrosion resistance, high strength and toughness characteristic of this metal render it particularly valuable. Nickel castings find extensive use in the construction of corrosion-resistant apparatus, and are often used in conjunction with wrought nickel sheet and tube in the fabrication of equipment for handling a variety of chemical and food products, particularly dairy products. In response to this demand for castings, numerous foundries have undertaken the production of castings of these metals and have met with varying degrees of success. The successful production of castings of monel metal and nickel requires careful attention to molding practice, proper melting equipment

Jan 1, 1930

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush's work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By C. G. Cheriton

The Bathurst mining district is located near the town of Bathurst on the north shore of the province of New Brunswick in eastern Canada. This region is the northeasterly extension of the Appalachian mountain system. The area is heavily forested and covered with a fairly uniform layer of glacial gravels and boulder clay. The relief is low, increasing to a few hundred feet in the north west and several hundred feet in the extreme southwest. Thus, rock outcrops are scarce and occur mostly along streams and ridges. These factors made conventional prospecting difficult and resulted in the district becoming an excellent place for the application of regional geological studies, air photo techniques, airborne and gound geophysical methods and soil sampling. Late in 1952, The Brunswick Mining and Smelting Company discovered a very large base metal sulphide body presently known as their No. 6 orebody. Early in 1953, another and even larger sulphide body was discovered and is known as the No. 12 ore body. Mining exploration was very active thoughout 1953 and in 1954, The American Metal Company discovered the orebodies which have been developed into The Heath Steele 'Mines. The location of these deposits is shown on figure one. In the latter part of 1954, The Anaconda Company became interested in the district and decided to make a geological study of this new and promising base rrietal area. The following paper presents the story of the application of modern geological and geophysical techniques, leading to the discovery of a large sul-nhidp liodv. The Bathurst district is generally underlain by the Tetagouche group of Middle Ordovician rocks.

Jan 1, 1961

By W. L. Saunders

WHEN work was begun in September, 1910, on the rock excavation for the foundation of the gigantic dam at Valhalla, N. Y., which is to convert Kensico lake into an important storage reservoir of the Catskill Aqueduct system, one of the first steps taken by the contractor, H. S. Kerbaugh, Inc., was the development of a quarry to supply the stone needed in the construction work.The importance of a bountiful supply of suitable rock in an accessible location is apparent when it is considered that nearly a million cubic yards of cyclopean masonry will be contained in the completed structure, not to mention dimension and facing stones, concrete blocks, and mass concrete. The dam structure will be over 1800 ft. long and about 170 ft. above the present river bed. However, for a distance of some 800 ft., it will be carried down to solid ledge rock, which will make the finished structure about 300 ft. in maximum height. It will be about 200 ft. thick at the base and directly beneath the coping it will be 28 ft. thick. This dam will raise the reservoir surface 110 ft. above old Kensico lake. The reservoir capacity will be 29,000,000,000 gal.-equal to New York's total needs for over two months. The contract price for this work is nearly $8,000,000 and is second only in amount to the cost, over $12,600,000, of the Ashokan Reservoir work. Fig. 1 is a view of the dam site.

Jan 2, 1914

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By C. E. Van Orstrand

An intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it mill be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. 11. Emmons minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. Mathematical Theory In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be as- sumed that the intrusive is a large par-allelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, 1 = o), which has the same thermal properties as the intrusive, is2,3 l-x v I FT 2 [2 2 — l-x m — y — m — y n — z In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. v = temperature at point x, y, z, time 1. v, = initial temperature throughout the intrusive, 1 = o. k = coefficient of thermal diffusivity. a, ß, y are variables of integration. Put n = m in Eq. I, and we have v I [2/5 [2I-x 2 — l-x m — y 2 2 2 kt 2 20xt e-a2da ebrdß

Jan 1, 1946

By Daniel T. Brian, O&apos

Exploration targets and results in the mining industry are commonly summarized in terms of tonnage and grade. Business appraisals require, as additional information, the expected profit or loss implied by the physical summay. The early incorporation of knowledge gained through financial analysis computations can provide a means for economically resolving many common exploration and development problems. Examples of such applications from the activities of exploration planning, reconnaissance, land acquisition, and development planning are presented. While prospecting for mineral deposits, geologists are frequently asked what they hope to find or have found. The response is usually descriptive, such as "50 million tons of 1% copper," and the economic implications are deferred until a capital investment decision is required. At that time, a financial analysis integrating the four analysis components is completed. These components are: 1) Tonnage and Average grade above cutoff grade 2) Capital and operating costs 3) Product value 4) Appropriate profit or loss accounting Close examination of these components reveals that there is no intrinsic reason for avoiding financial analyses at earlier stages in exploration, as long as the uncertainty of the estimate is realized. Tonnage and average grades are commonly estimated at early stages in exploration. For this component, the appropriate cutoff is the major uncertainty. Capital and operating costs are difficult to estimate before detailed quantitative information is available, but estimates useful for the types of applications pertinent to earlier exploration stages are possible. Product value estimates may or may not be difficult, depending on the pricing structure of the particular commodity. A simplified accounting procedure usually may be adopted without introducing any significant loss of validity. This paper describe some of the financial analysis applications which are pertinent during mineral exploration and deposit development. These applications lend additional insight during exploration planning, land acquisition, physical exploration, and development. The examples are oriented toward a hypothetical management investment policy which is based on a single criterion, a minimum 15% discounted cash flow rate of return. In reality, managements use multiple criteria. This simplification is convenient for purposes of presentation and does not invalidate the examples. Computers are useful, but not a requirement, for the applications described. The use of computers provides the results on a more timely basis at costs lower than equivalent manual computations. UNDERLYING PRINCIPLES AND ANALYSIS METHODS Data estimates are subject to uncertainty. The analyst may choose to assess this uncertainty by using one of two principles. Each principle has some advantages. The principle most commonly employed is "assumed certainty." Each financial analysis is based on one set of selected data, which may represent the average estimates, minimum expected conditions, etc. The critical data is identified by making successive calculations, varying the values used. Such studies, called sensitivity analyses, isolate the economic effect of various uncertainties, and guide the allocation of future efforts toward improving the overall accuracy of the analysis. A second principle, "assumed risk," examines the interactive effect of the current uncertainties by qualitatively assigning probability distributions to each data element. These probability distributions indicate the currently appraised chance that a given numerical value will prove to be true. The corresponding procedure, risk analysis, consists of processing many individual financial analyses, each analysis being based on randomly selected numerical values from the probabilistic distributions. The result is a numerical presentation of the uncertainty, but care must be exercised in the interpretation of results. The advantage of this procedure is the direct measurement of economic uncertainty caused by the interaction of uncertain estimates. Kennecott Copper Corp. has developed computer systems for accomplishing sensitivity and risk analyses.

Jan 1, 1970

The regular activities of the Institute are financed mainly by income derived from members' dues, from advertising in MINING AND METALLURGY, and from the sale of publications to the public. In addition, collateral activities and special projects are financed each year by means of income from endowed funds controlled and administered by the Institute. In the aggregate, the principal sums of these endowments amount to more than $530,000. An active effort is being made to increase the endowment funds of the Institute through a standing committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, D. C. Jackling, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1941

By Phillip E. Deering, Robert M. Cox

A model pillar study was conducted in which the engineering principles of dimensional analysis were applied to the problem of coal mine pillar design. The paper reviews the theory of similitude as applied to the model pillar study conducted in the investigation. An example solution of a design problem is included to indicate how the results of the study may be used as a first approximation in the design of coal mine pillars. The design of mine pillars for adequate support with minimum loss of valuable raw materials has always presented a problem to the mining engineer. Most often, for lack of a better method, past practice has influenced the design of new mine pillars. This process has always left doubt as to the safety factor of the pillars. The work presented in this paper is an initial attempt toward adapting the engineering principles of dimensional analysis to the problem of pillar design in underground mines. The use of the dimensional analysis technique is advantageous because all the variables associated with the problem are considered, and by systematic analysis the relative influence of each variable is determined. The model material utilized in this study was taken from the Helena seam of the Cahaba coal field located in central Alabama. The research study was sponsored by The Southern Electric Generating Co. as part of an over-all rock mechanics investigation of the Helena seam area. THEORY OF SIMILITUDE Model analysis is used extensively in engineering today, particularly in the solution of design problems that defy the classical methods of analysis. Such problems arise when materials with a nonlinear stress-strain relationship are involved, when geo- metric boundaries are difficult to define in simple form, when strains become large, or when partial failure occurs. All of these difficulties usually exist in pillar design problems. Those principles which underlie proper design and construction of models, and the interpretation of test results, comprise the theory of similitude. That is, the theory of similitude includes a consideration of the conditions under which the behavior of two separate entities or systems will be similar, and the techniques of accurately predicting behavior of one from observation of the other. The theory of similitude may be developed by dimensional analysis. Dimensional analysis, as a powerful analytical tool, is developed from a consideration of the dimensions in which each of the important quantities involved in a phenomenon is expressed. It is based on two axioms: 1) Absolute numerical equality of quantities may exist only when the quantities are similar qualitatively. 2) The ratio of the magnitudes of two like quantities are dependent on the units used in their measurement, provided that the same units are used for evaluating each. Dimensional analysis, developed from these two axioms, differs from other types of analysis in that it is based solely on the relationships that must exist among the pertinent variables because of their dimensions, rather than on the relationship of natural laws. In itself, dimensional analysis ~rovides qualitative, rather than quantitative relationships, but when it is combined with experimental procedures, it may be made to supply quantitative results and accurate prediction equations. APPLICATION OF THEORY The design of an adequate mine pillar requires the determination of a design equation and the selection of a dimensional system with which to work. Since force plays an important part in the design of mine support, the FLT (force, length, time) system has been used. The factors involved in the dimensional analysis of mine pillars and their dimensions are: A = cross-sectional area L Cp = design strength FL- E, = tangent modulus of elasticity FL

Jan 1, 1969