Search Documents

By R Blair

The Domain and Burnley Tunnels, which are major features of the Melbourne City Link Project, are MelbourneÆs first road tunnels. They are 1.6 km and 3.5 km in length respectively and are being constructed through a variety of ground conditions. Deeper sections of the tunnels have been driven through the Silurian mudstone which underlies Melbourne. Other shallower sections of the tunnels pass through a variety of ground conditions including silts, sands, clay and rock and have been constructed using both top-down and bottom-up cut and cover construction techniques. The Yarra River Crossing is a 140 m length of the Domain Tunnel which crosses under the Yarra River on a relatively shallow alignment. The crossing of the river using cut and cover techniques was identified in the early stages of design development as being one of the most challenging stages of the works on the Southern Link. The prevalence of varying geological conditions combined with the need for maintained traffic and stream flow conditions provided a demanding and often conflicting set of criteria for which there appeared to be no one clear solution. A team of designers, constructors, estimators and specialist contractors were involved in a concept evaluation and risk analysis study spanning a period of approximately 12 months. During this study, four concepts were considered as likely contenders. This paper provides a brief outline of the four concepts addressing their relative merits, disadvantages and risks followed by a detailed description of the adopted solution, namely top-down construction using secant pile walling (east bank) and bottom-up in situ construction (west bank).

Jan 1, 1999

By Mohammed Z. Islam

As cities are growing all over the world, the need for urban transportation facilities are on the rise. Designers (of these facilities) today are faced with a number of constraints for their design, of the most is the space limitation and impact of new construction activities to the community. A typical subway station, as the focus of this paper, is approximately 600 to 1000 feet long, 50 feet wide and 2 to 3 story high. With such a large volume of construction activities, it is easily realized why underground stations are becoming obvious choice for larger cities eventhough the cost could be 2 1/2 to 3 times as much as an aerial station and 4 to 5 times that of an at-grade station [O'Neil et. al.(1977)]. Since cost is an important factor which is always increasing, therefore, the designer should have a good planning, consider alternatives for design and come up with a realistic design with minimum impact to the community. This paper is about the geotechnical considerations that the designer should be aware of. PLANNING A 1977 report [O'Neil et. al.(1977)] on the construction costs for a number of underground subway stations indicate that about 4 0% of the cost is site-controlled, 35% is structural items, and 25% is finish and equipment. It is seen that of opportunity exists for cost savings in the site selection and proper use of the site. Once the site is selected, the cost of construction become controlled by urban conditions at the site, geotechnical conditions, station size and depth. Therefore, the design-solution is very much site-specific. The geotecnical designer should collect the following information at the early phase of the design:

Jan 1, 1993

By R. P. Rothwell

IN January last I published in the Engineering and Mining Journal a table giving, with a considerable degree of accuracy, the production of anthracite coal for the year 1874. At that time it was impossible to give any correct estimate of the production of bituminous coal, for the returns I had been able to secure from such distant and scattered districts were not always forwarded punctually, and the work of -obtaining anything like a true estimate of the coal mined in districts from which I was unable to obtain official returns was both laborious and tedious. As will be seen from the detailed reports furnished herewith, I have succeeded in obtaining tolerably accurate returns of 20,093,704 tons; and upon careful revision by numerous well-informed local authorities, my first estimate of the amount of coal not officially returned to me has grown very considerably; indeed, as I get more information on the subject I find that our bituminous coal production greatly exceeds the amount we have been accustomed to hear it placed at, aggregating as it does, 26,465,704 tons. Mr. Andrew Roy, State Inspector of Mines for Ohio, has reported the production of Ohio at 4,168,445 tons, while his first estimates were but 3,820,000 tons; and similarly, in other cases, the more full the returns direct from the mines the more incorrect do I find all previous reports. I am able now to furnish, not an accurate statement, indeed, but by far the most full and reliable one that has yet been published of our coal production. The amount of labor involved in obtaining this admittedly imperfect report has been simply enormous. In the following tabular statement it will be perceived that Pennsylvania produces nearly one-half of all the bituminous coal mined * Since this paper was read fuller reports from some of the States whose production had been "estimated" have modified the figures given. The most serious error is in California, which produces probably 200,000 tons less than these figures. Oregon and Washington territories also yield smaller amounts than here reported; but these reductions are probably fully compensated by fuller reports from other States that were here underestimated. The correct aggregate amount will not vary much from that here given. Early in 1876 I will be able to give a fuller and more accurate report for the year 1875.

Jan 1, 1875

By Ola Lindahl, Mark Irving, John Hutchings

"Blasting is a process starting with a geometric description of the block of rock and ending with a pileof fragmented material. A key step in improving the productivity and quality control over the processis the integration of blast planning software, explosive delivery control systems, and blast recordingwithin one seamless customer solution."

Jan 1, 1997

By Markus Schönit

Double rotary drilling combines continuous flight auger drilling with a casing for producing a cast-in-place pile. When producing a pile an outer casing and an auger (hollow auger) rotating inside the casing are driven into the ground in counter-rotation. The outer casing serves to support the surrounding soil and the inner auger excavates the drilling cuttings to the surface inside the casing. After reaching the projected drilling depth concrete is pumped through the hollow stem of the auger and outer casing and auger are extracted. After their complete extraction a reinforcement cage can be inserted in the fresh concrete. Compared to Kelly drilling the double rotary drilling method offers numerous advantages, including, for comparable diameter and length, shorter production times and higher accuracy (pile inclination and excess concrete) combined with increased occupational safety and lower noise emissions. Moreover, pile tests have proved that piles produced by double rotary drilling feature higher axial load-bearing capacities than comparable piles produced by Kelly drilling. This article offers an overview of the basic theoretical principles of double rotary drilling lists the required and currently available machinery and, finally, discusses the results and conclusions of a current jobsite.

Jan 1, 2011

By David D. Hottinger

Only a minimum amount of illumination is generally provided for many types of mobile surface mining equipment. This condition presents a hazard to operating personnel working on and around such equipment. To reduce this hazard MSHA has proposed safety regulations requiring minimum levels of illumination for hazardous zones on and in the immediate area surrounding surface mining equipment. This report describes a Bureau of Mines sponsored project demonstrating the feasibility and effectiveness of providing dragline illumination in compliance with the proposed MSHA regulations. A description of the computer aided design, on site installation and field evaluation of individual lighting systems for each of three different size draglines is presented

Jan 1, 1981

By Y. H. Wang

During the last two decades many research projects were conducted to study the load requirements for the powered supported longwall faces (1-6). Significant results had been achieved by these researches. Most of the previous studies were rarely designed to understand the mechanisms of interaction between the supports and the surrounding rock, or to correlate the stress conditions around longwall faces to the mining operations both in time and space. In case of the shield supported faces, the roof-to-floor convergence is very difficult to measure due to the high percentage of roof coverage. The external load on the supports can not be determined from the leg pressure data alone due to the existence of the lemniscate links. Therefore, there is a real need in that a simple engineering method be developed to monitor the variations of roof load on the shield supports, the roof-to-floor convergence and the roof stress restoration in the gob area as the mining proceeds. Only with the results of these measurements, a further understanding about the mechanisms of interaction between the supports and the surrounding rock can be achieved and a criterion of designing or selecting the optimum mechanical parameters of the shield supports can finally be developed.

Jan 1, 1986

By James C. Patterson

Sintered fly ash was shown to have promise as a modifier for poorly drained soils. Turf grown in mixtures of sintered fly ash and soil benefited from increased water-infiltration rates, greater total pore space, and higher moisture availability, The result was an improved turf stand with increased grass yield and root density.

Jan 1, 1970

By L. Li

The performance of microemulsified diesel and conventional diesel collectors in coal flotation was compared by flotation indicators, including combustible recovery, ash content of the clean coal, and the flotation index. An efficient separation with lower dosage was obtained using the microemulsified diesel collector. Under optimum separation conditions, the microemulsion consumption was 100 g/t less compared with diesel. The saving in diesel consumption using the microemulsion reached about 70%, disregarding the consumption of the surfactant and cosurfactant. Frothing tests showed that the frother dosage was decreased by using the microemulsion collector, because of the surfactant and cosurfactant added during preparation. The microemulsified diesel collector is superior to the conventional diesel collector in terms of diesel consumption and separation efficiency, but the selectivity requires further improvement. Keywords froth flotation, microemulsified collector, coal.

Nov 1, 2013

Recent literature is reviewed with emphasis on the design and scale up of mixers. Most important aspects of mixing have resulted from the study of Newtonian fluids and only a minor attempt has been made to extend the work to non-Newtonian materials.The rheology of non-Newtonian materials is outlined and the typical behaviour of mineral slurries is indicated.The importance of flow velocity, flow pattern, and fluid turbulence is discussed with relation to suspension of solids and rate of reaction.Data on experimental leaching of ore from Mary Kathleen, Queensland, show the effect of different mixing impellers.In conclusion, factors involved in the selection of a mixer are presented with emphasis on economic appraisal after pilot experimentation.INTRODUCTIONThe subject of mixing has attracted considerable attention during recent years, but relatively little work has been undertaken for the study of non-Newtonian materials. Most work has been restricted to Newtonian fluids because there are less inconsistencies in such study.Mixing, by definition, implies blending or combining, and ranges from gentle mixing which blends the contents of a large tank in 24 hours to violent mixing which completely homogenises the contents of a tank within seconds. Metzner and Otto (1957) have pointed out the present lack of knowledge on the degree (or quality) of mixing. Apart from this fact the design of mixers for Newtonian materials would seem to be reasonably certain.Both capital and operating costs rise rapidly with increasing mixer size. Therefore the design, or selection, of a mixer is a matter for economic consideration in the overall aspect of plant design and operation.

Jan 1, 1961

Bioleaching of Weathered Saprolite - Heavy Metal Adaptation Mechanisms of Aspergillus foetidus Nickel laterite ores remain important to the future supply of Ni and Co as they contain the bulk of known nickel and cobalt reserves (80 per cent and 90 - 95 per cent respectively). Current commercial extractions of Ni and Co from nickel laterite ores are energy intensive and operational costs are high. Microbial leaching of oxide ores has the potential to offer a much needed step-change in the technology for processing laterite ores. Biological leaching of low-grade nickel laterite is based on a non-traditional leaching of oxide minerals using heterotrophic micro-organisms. The organisms solubilise metals by excreting organic acids; these acids then form complexes with heavy metals. Optimisation of the process in in-situ application, however, has been hampered by the toxicity of the heavy metals that are being leached by the organisms. Our recent study has shown that organisms are able to develop tolerance towards heavy metals by adaptation. This study examined the extracellular metal detoxification mechanisms of A. foetidus in 0.2 per cent (wt/v) to 0.7 per cent (wt/v) of weathered saprolite ore. To support our analysis, FTIR, CHNS and microscopy were used to confirm the participation of specific functional groups in the extracellular detoxification process.

Sep 13, 2010

By Miles T. Stephens, Felipe Calizaya, Jacob O. Kingston

Currently, the Bear Canyon Mine is facing the challenge of excessively high coal and rock temperatures in one of its headings. In Mine No.3, the air temperature at the 6th Right panel reached 36.4ºC and the coal 83.9 ºC. Due to these severe work conditions, the mining plan has been altered by changing the mine direction to avoid the high temperatures. To investigate the problem, drill holes were developed from the entries and the rock temperatures monitored using K-type thermocouples. The measurements confirmed the existence of localized “hot spots” in the mine. This paper presents a summary of ventilation surveys that were conducted in this mine. It includes the results of coal and rock temperature measurements from drill holes, interpretation of results using a heat flow simulator and the identification of hot spot areas. It also includes a summary of methods that were developed to reduce the hazard and control the problem.

Jan 1, 2005

By K. [Muthukkumaran

An extensive program of laboratory model tests was undertaken to study the effect of slope on p-y curves under passive loading in dry sand. The paper concerns the method developed in a series of laboratory model tests to experimentally determine p-y curves. Bending moment curves are differentiated by using curve fitting method of cubic polynomial function. The study includes effect of slope angle and relative density on bending moment and non-dimensional p-y curves. The non-dimensional p-y curves for piles on sloping ground under passive load are developed modifying API method by including a Reduction Factor (R) using the experimental results.

Jan 1, 2006

By Steve Kral

For an industry that provides more than half of the nation’s energy needs, the U.S. coal industry still attracts negative publicity. However, the nation’s energy appetite continues to increase. And political leaders and the public are beginning to understand that alternative fuels will not be enough to keep up with that appetite. Does that mean the nation will now embrace the coal industry? No, according to speakers at the Rocky Mountain Coal Mining Institute (RMCMI) meeting. The industry still needs to sell the public on coal’s advantages over other fuels. And the industry must continue to develop technology that will allow coal to meet and exceed strict clean air and clean water regulations.

Jan 1, 2002

By R. W. Stahl

An emergency is defined as an unforeseen combination of circumstances that calls for immediate action. When applied to a coal mine, an emergency may call for prompt removal of the men to the surface through travelways other than the haulageway or intake airways, which are generally contaminated with irrespirable air as a result of an explosion or fire. Therefore, maintenance of adequate and travelable escapeways from all working areas of a mine is vitally important insurance against disaster. Several mine disasters could have been avoided if well-defined escape routes had been provided and made known to all mine employees. Such occurrences, unnecessary as they generally are, unfairly indict the industry when only a small segment thereof is involved. As a result of a rather recent disaster, which might not have happened if good escape routes had been provided, the Bureau of Mines decided to delve into the escape procedure to determine (1) what is being done in the industry and (2) what might be done at reasonable cost.

Jan 1, 1962

By V. F. Parry

[Subbituminous coal or lignite when stored in random piles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. These changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently, stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.]

Jan 1, 1941

By D. R. Brox, J. Levell

The Montana Tunnels Mine was mined out to a depth of 900 feet at the end of 1999. The first signs of instability were recognized in 1996 along the upper slope area of the northwest sector when the pit was mined out to a depth of approximately 500 feet. To extend the life of mining operations, it has been proposed to extend and steepen the northwest highwall to a depth of 1000 feet. Slope stability analyses were carried out using the UDEC software program to assess the stability and deformation of the proposed highwall design. Back analysis of an instability in 1997 along the upper slope section and highwall deformation to date has indicated reasonable agreement with the observed mode of failure and displacement monitoring results. The results of detailed analyses of the proposed highwall design have indicated very limited additional deformation, further development of tension cracks is unlikely and large-scale instability is not expected to occur. A total of 40% of additional mining has been completed and ongoing displacement monitoring to date has confirmed very limited additional movement and no further tension crack development.

Jan 1, 2001

By B. Gazea, A. Kontopoulos, A. Kourtis, K. Adam

Static tests give a measure of the balance between acid-producing and acid-neutralising mineral components in a material, while kinetic tests determine acid generation and neutralisation over a long period. Drill-core samples from the amphibolite and gneiss host rocks of the Stratoni lead-zinc sulphide deposit in Greece and mine/mill waste samples from Stratoni and Olympias were examined by the standard acid base accounting, BCR and net acid production tests. Mineralogical data on the materials and resulting residues were used to illustrate the differences between the methods and establish their ranges of applicability. BCR seems to simulate most closely the conditions prevailing during generation of acid mine drainage but is time-consuming and requires elaborate equipment. Acid base accounting is suggested for standard screening; net acid production might be used in the field or for solids with less than 10% S

Jun 19, 1905

By B. S. Terry, C. L. Harris

Reduction kinetics from slags containing CuO(0.5), ZnO, PbO, NiO and SnO into a Cu-based metal phase were subjected to computer simulation using a previously developed model for the kinetics of metal-slag-gas reactions that assumes mass-transfer control in all phases. The effects were examined of changing bulk Fe oxide activity, gas reducing potential, temperature, Fe content of the Cu phase and metal/slag ratio. The results permit practical conclusions to be drawn about industrial slag-cleaning practice, but the model is still limited in terms of thermodynamic inputs and the idealisation of reaction conditions

Aug 1, 1995

By Hamid Maleki

In this paper, the authors present a review of data gathering programs and stress analyses for improving mine layout designs at BRL mines located near Paonia, Colorado. BRL and other companies have used both longwall and continuous miner methods for the extraction of the Upper D, Upper B, Lower B and C seams from the multiple-seam reserves in the North Fork Valley. Historic mining in the B and C seams has created stress footprints in the neighboring unmined seams compounded by stress transfer from recent longwall extraction in the Upper D Seam. Thus optimum positioning of workings in the remaining reserves requires careful collection of pertinent data and consideration of load transfer from previous workings through remnant abutment pillars. Based on long-term subsidence monitoring, underground mapping and stress analyses, we have confirmed initial load transfer analyses finding mild interactions between the UD and LB workings, and the mining conditions have proven to be good and manageable during the development stage of the LB Seam. This has been achieved through prudent mine planning, prudent positioning of the gateroads in multiple seam workings and support allocations.

Jan 1, 2007