Search Documents

By Steven J. Page, Andrew B. Cecala, John A. Organiscak

In This Chapter [Drill dust control: wet and dry Enclosed cabs on drills and mobile equipment Haul road dust control] Overburden drilling generates most of the respirable dust that affects workers at surface mines. Both wet and dry methods are available to reduce this drill dust. Overburden removal by mobile excavation equipment such as bulldozers, front-end loaders, and haulage trucks can be dusty, particularly under dry and windy conditions. Tightly enclosed cabs with dust filtration systems can substantially lower the dust exposure of both drill and mobile equipment operators. Haul road dust control can be achieved by water application or chemical application. DRILL DUST CONTROL [Drill dust is controlled with wet or dry systems. Wet systems can be more efficient, but may freeze in the winter. Dry systems require careful maintenance of the drill deck shroud. An improved deck shroud is shown.] Wet Suppression. Wet drilling systems pump water into the bailing air from a water tank mounted on the drill. The water droplets in the bailing air trap dust particles as they travel up the annular space of the drilled hole, thus controlling dust as the air bails the cuttings from the hole [Page 1991]. In wet drilling systems, typical water flow rates are 0.1 to 2.0 gpm depending on the size and type of drill and the moisture level of the overburden. The drill operator controls the flow using a control valve located in the cab. Some drills are equipped with a flow meter to give the opera-tor a visual sign of the flow rate. Raising the water flow will improve dust capture, but too much water causes operational problems. Because of this, the drill operator must exercise care in find-ing the best water flow rate.

Jan 6, 2003

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

Samples weighing 0·5 g are decomposed with hydrofluoric and other acids. Most elements are extracted ftom the acid, aqueous solution by Alamine 336 (tricaprylyl tertiary amine) and thorium is determined in an aliquot taken from the aqueous phase by means of its reaction with arsenazo III. Concentrations down to 4 p.p,m. may be determined at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

By M. Hagfors

Underwater explosions have been used several decades for the determination energy content of explosives. It’s the only test method by which shock and gas heave energy values can be determined separately. The total energy is a sum of these two partial energies. This test method enables us to develop explosives for different purposes; the military high explosives should contain more shock energy whereas the gas heave energy is a very important feature for the blasting explosives. The method also enables us to observe the changes and to adjust the energy content of an explosive as a function of increments of one or more energetic component.

Jan 1, 2006

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

By R. F. Pilgrim

"This first chapter of the SPOC Manual 1s intended as a general introduction to all the other chapters in which the mineral process evaluation and optimization methodology is presented. This chapter also provides a brief description of available software for mainframe and m1crocomputers and provides information on its distribution by the Technology Information Division. CANMETRESUMECe premier chapitre du manuel SPOC est un guide général qui présente les autres chapitres ou l'on traite de la méthodologie d'évaluation et d'optimisation des procédés miméralurgiques. Le lecteur y trouvera aussi une description sommaire des programmes de calcul développés pour ordinateurs centraux et pour micro-ordinateurs ainsi que la façon de les obtenir de la Division de l'information technologique du CANMETComputer simulation of mineral processes has slowly emerged as an established branch of activity in A&D centres and in several teaching institutions after decades of slow progress. Substantial efforts to develop application software based on years of research on process modelling are being pursued in many countries ( 1 .2,3,4.5). The late BO's should see a flurry of success stones about significant leaps of productivity achieved in several plants through systematic process evaluation and computer simulation studies.In Canada. the SPOC project (Simulated Processrng of Ore and Coal) was initiated at CAN MET in 1980 with the obJective of developing and transferrrng to the mineral rndustry a computer-based methodology for process evaluation and optimization. The proiect deliverables include:- an engineering manual covering most aspects of off-line computer simulation:- a bank of FORTRAN software accessible through data communication lines for user familiarization and distributed at a nominal cost in source form by CANMETThe yearly progress reports of the project contain detailed information on the project elements since 1980 16). The context of SPOC can be summed up by quoting Gordon Agar""s 1975 statement during a workshop on research needs in the mineral industry: ""What is needed is a joint effort between the academic community and one or more enliglitened industrial concerns. The effort will have to be an iterative one with data collection followed by testing the model modification of the model (s), more testing prediction, modification. data collection and so on (7). A few parallel in1- t1atives had been reported in papers or research contract reports (8, 9) but there was an obvious need for CANMET to bridge the gap between the R&D and the production sectors by undertaking a project that would document past applications and induce a new generation of initiatives through the consol1dat1on and transfer of suitable manuals and software. The effort took shape as the CANMET SPOC pro1ect in which methodology transfer was to play a key role (10)."

Jan 1, 1986

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to date and more nearly in line with present operating and safety practices in the industry. The rules are intended to supplement existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment, or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By J Charbucinski

Commonwealth Scientific and Industrial Research Organisation (CSIRO), Exploration and Mining, has developed nuclear spectrometric techniques for borehole logging. The paper reviews the latest developments of this technology for the metalliferous mining industries. The SIROLOG logging system developed by CSIRO Exploration and Mining has been commercialised and is available to the mining industry.

Jan 1, 2000

By W. C. Joughin

Problems with the stability and performance of rockpasses in deep-level mines are common. This paper presents the results of an investigation into the recorded performance of rockpasses in deep-level gold mines. Records relevant to the geological environment in which the passes are excavated, their excavation details, and their historical performance are not at all well documented on mines. In general, the quality of data available from mines is poor. The investigation showed that very large spans frequently developed in passes during use, and that rock mass quality, the orientation of the pass with respect to the dip of the strata, and the magnitude of the stress acting normal to the axis of the pass were the main factors of influence. From the historical information obtained, the risks of instability in rockpasses are identified.

Jan 1, 2005

By A. J. Lynch

Mineral processing models have been discussed for many years but it was not until digital computers became available about 1960 that serious attempts at circuit simulation could be carried out. Even then the work was primarily academic until PCs could be used by engineers in plants and design offices in the mid-1980s. Since then simulation has moved quickly and it is now at the point that most processes can be simulated reasonably accurately for purposes of design and optimization. There are still some significant deficiencies, notably in dry grinding and separation, and in the chemical interactions in flotation. Future work will involve: ?improvements of existing models ?dynamic simulation for automatic control and, in particular ,for training which is a weak link ?using advanced simulation models to predict liberation and separation from data acquired from SEM-based liberation analysers. Eventually mineral processes models will be part of total simulation systems which will incorporate mining and downstream processes including all environmental impacts.

Jan 1, 1999

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By Edward D. Graf

Once the heavy work of mining, supporting and completing an underground structure is finished, there is frequently the problem of handling unwanted water infiltration into the opening. Methods of controlling the infiltration vary from collecting and channelling the inflow to shutting off the water at the surface of the opening or within the ground formation. Discussed are various methods of controlling ground water inflow from within the structure including collector pipe systems, shotcrete, cement grout, bentonite, and various chemical grouts. Case histories illustrating some of the methods and materials will be presented.

Jan 1, 1987

By John C. Machisak

THIS PUBLICATION presents injury experience and employment data for the nonmetal mining industry in the United States for 1960. Data for the mines and mills are presented separately, as shown in the list of tables. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry for their voluntary submission of injury and employment data. As the information submitted contributes largely to the promotion of safety in the industry, special effort has been made to make these questionnaires as complete as possible.

Jan 1, 1963

By E. Carvajal I

Large diesel engines provide the mining industry the substantial power and torque needed to move large amounts of material efficiently. But the stresses generated by such power and torque necessitate complex maintenance programs to ensure the utmost operating capabilities are not compromised. Of all its available sensors, the Exhaust Temperature differential between the right and left banks can provide the most valuable indicator of the overall operating condition and potential degradation of a large diesel engine. BHP Billiton Escondida Mining has implemented real-time remote monitoring, diagnostics, reporting, and tracking of Exhaust Temperature differential using Modular® technology. As a result of the processes and procedures put into place surrounding their MineCare maintenance management system, Escondida has proactively replaced over 300 injectors, resulting in an increase of 4% in Engine availability.

Jan 1, 2011

By J K. Wright

In recent years the production of steel from directly reduced iron ore pellets has expanded rapidly. However, continued growth will depend on an adequate supply of suitable raw materials for the various commercial gaseous and solid reductant processes now in operation. Although at present Australia does not produce pellets primarily for direct reduction, there is an increasing awareness of Australia's potential role as a supplier of high grade ores for export and/or domestic use. The properties and quality requirements of iron ore pellets made specifically for direct reduction (DR) are reviewed and the laboratory techniques and test methods used at the CSIRO Division of Process Technology for the evaluation of potential DR feedstocks are described. At the present time most of the evaluation tests for DR pellets are extensions of those designed for existing blast furnace (BF) burdens. In the case of some physical parameters such as cold compression strength, abrasion index and cold strength after reduction this extension is quite satisfactory. In the measurement of parameters such as reducibility, swelling and sticking tendency, however, it is necessary to develop meaningful standardized tests so that ores and pellets can be ranked for DR performance. To do this, data from the laboratory tests and from operating plants must be correlated.

Jan 1, 1980

By Jelke Dijkstra

This paper presents the results of model pile load tests in a photoelastic material. The soil in this test is represented by an assembly of photoelastically sensitive glass particles, which allows for optical measurements of stresses. In the same test setup, displacements around the pile are measured using digital image correlation (DIC). During the pile installation stresses and strains are recorded. Tests were performed in loose and medium dense particle assemblies. The development of stresses and strains around the pile tip and pile shaft are quantified and presented in this paper. For the loose conditions the results show a small influence on the stress state. For the medium dense conditions a clear stress change is observed.

Jan 1, 2006

Economically significant gold-silver mineralization occurs in Miocene andesitic flows and tuffs at Golden Cross, eight kilometres northwest of Waihi, New Zealand. The highest grade mineralization occurs in a steeply dipping elongate zone of strong quartz veining and brecciation underlying, but contiguous with, a gently dipping tabular quartz vein stockwork containing potentially open-pittable lower grade gold-silver mineralisation. The stockwork zone is enveloped by argillic alteration and overlain by unaltered Pliocene andesites and recent tephra. Evaluation of the prospect involved underground and surface geologic mapping, rock and soil geochemistry, IP-resistivity, magnetic and gravity surveys as well as 1844 metres of reverse circulation drilling and over 30 000 metres of core drilling. The paper outlines the exploration history of the area and describes the results of the various exploration techniques used at Golden Cross.

Jan 1, 1986

By Aly M. Mohammad

The 12th and 14th Street Viaducts, which carry Route 139, are located west of the Holland Tunnel in Jersey City, New Jersey. The two viaducts, provide access to and from the Holland Tunnel (which connects New York City and New Jersey) and carry upwards of 50,0000 vehicles per day from Jersey City and New York City to points west. The New Jersey Department of Transportation (NJDOT) selected AECOM to perform design services including rehabilitation and seismic retrofit for the 12th Street and 14th Street Viaducts while maintaining traffic at all times. Building a new parallel bridge just north of the 14th Street Viaduct was essential in avoiding extremely costly traffic delays. Installation of the new foundation, in close proximity to the existing viaduct, required drilling through some of the existing timber piles supporting the bridge. As a result, the existing bridge was required to be reanalyzed for this new foundation configuration. This proposed structure consisted of 8 piers each supported on a single six (6) foot diameter drilled shaft. Currently this portion of the bridge structure has been constructed. The shafts were constructed with rock sockets that were five feet six inches (5?- 6??) in diameter and were extended 11.2 feet (3.4 meters) into rock. A 2300 ton Osterberg Load Test was performed on one production shaft to confirm the capacity of the shaft. The rock socket for the test shaft was in sandstone. This paper will present a description of the design methodology and construction methods adopted for the foundations. In addition, the paper will illustrate the Osterberg Load Test including: equipment used, number and locations of strain gages, and interpretation of results. Additionally, regarding the close proximity of the new foundation, the paper will present the type of equipment used to drill through the existing timber pile foundation while minimizing the impact on the integrity of the existing foundation. We will also present the method of analysis for analyzing the redistribution of load on the remaining piles. The results presented in this paper will assist the design engineer by providing a comparison between the geotechnical design assumptions and the actual measurements obtained by field measurements for this rock formation.

Jan 1, 2009

By Will Hunt, Darren Thornton

In March of 2013, an undisclosed gold mine (MINE X), located in the Western United States, performed blast movement monitoring of three blasts occurring in one of two active pits. Blast Movement Monitors (BMMs) were placed in the bench before blasting, and located after the blast to determine vectors of movement. Using blast movement software, ore/waste boundaries were translated. These locations were compared to MINE X’s standard ore translation procedure, which consisted of moving polygon boundaries by 17.5 feet (5.3 m) in the burden direction of the blast hole pattern. This translation amount, identified by MINE X as “average” motion, had been ascertained by performing a previous blast movement study.

Jan 1, 2014

By J Law, S Jahanshahi, R Holmes

Iron ore is AustraliaÆs largest commodity export and is vitally important to AustraliaÆs current and future prosperity. However, while major expansions are currently in progress to satisfy demand, the industry is also undergoing major transformations. Reserves of traditional high-grade Brockman ores that have underpinned the Australian iron ore industry since its inception are slowly being depleted and alternative ore types such as Marra Mamba bedded iron deposits, Yandi and Pannawonica channel iron deposits and magnetite deposits are now being developed. However, the impurity levels in some of these alternative ores are higher and they require blending and/or upgrading as well as an advanced knowledge of their downstream processing characteristics to facilitate cost-effective utilisation by overseas customers. The research challenge is to use advanced techniques for mineral exploration, ore characterisation, mineral beneficiation, agglomeration and sustainable processing to identify and develop innovative and breakthrough options for locating, unlocking and enhancing the value of AustraliaÆs iron ore resources. Furthermore, to sustain the steel industry and hence secure the demand for iron ore, there is a growing need to enhance the environmental and business performance of the industry through reductions in wastes and emissions. Therefore, cost-effective breakthrough and enabling technologies that massively cut waste generation, CO2 emissions and water consumption are also being developed. These include the use of renewable fuels and reductants, waste heat recovery and conversion of by-product slag into a saleable substitute for Portland cement. A number of examples of recent developments in the above areas are provided in this paper.CITATION:Holmes, R, Jahanshahi, S and Law, J, 2013. Research and innovation for the iron ore to carbon steel value chain, in Proceedings Iron Ore 2013 , pp 3-6 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013