Search Documents

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By T. O. Hagan

A simulated rockburst experiment was conducted underground at a deep level gold mine. This was done by means of a large explosion detonated in solid rock close to a tunnel sidewall. The resultant shake-out damage is typical of that associated with a small seismic event in close proximity to a tunnel that is subjected to the estimated field stress, as in this case, of 50 MPa. The experiment involved: ?the design of a blast to mimic a seismic source ?seismic monitoring using a dense seismic array ?high speed video filming ?a study of rock mass conditions (fractures, joints, rock strength etc.) before and after the simulation using mapping and ground penetrating radar ?special investigations to evaluate the mechanism and the magnitude of the damage ?a study of support behaviour under excessive dynamic loading.

Jan 1, 2001

By S. Parada, P. T. Jones, M. Guo, S. Smets

The corrosion behaviour of a high-quality rebonded magnesia-chromite refractory in contact with a vacuum oxygen decarburization (VOD) slag with high Al2O3content (15?20 mass per cent) is investigated under VOD process conditions by rotating finger tests in a vacuum induction furnace. The refractory degradation mechanisms are studied by the characterization of corroded microstructures using scanning electron microscopy, equipped with energy dispersive spectroscopy. The influence on the refractory wear of the process temperature and the Al2O3content in the slag is discussed. Keywords: corrosion, magnesia-chromite refractory, VOD slags, vacuum induction furnace

Jan 1, 2004

By G. W. Jones

The results presented in this report deal with the elimination of explosion hazards of ether-oxygen mixtures by the addition of helium. The method is based upon the fact that every combustible gas, vapor, or dust will not burn or explode when the oxygen content of the mixture is reduced below certain definite values. These critical oxygen values are usually different for each combustible, varying with the percentage of the combustible present in the mixture and also with the inert gaseous material used to reduce the oxygen content of the mixture.

Jan 1, 1941

By John D. Spencer

Surveys to establish the quantity and quality of coals available for metallurgical, industrial, and energy use, investigations to develop better mining methods, and studies aimed at improving the health and safety of those who mine the coal highlighted Bureau of Mines research and technologic work on coal in 1968. Also being developed are more efficient methods of coal preparation, transportation, storage, and utilization. Supplementing this effort are projects designed to assure minimum disturbance of land, water, and air resources. Research centers and laboratories of the Bureau of Mines are listed in appendix A. Publications released during 1968 are cited with the various projects and in appendix C. Organizations that cooperated in the work in various ways are cited in appendix B.

Jan 1, 1969

By Donald A. Bruce

Pin Piles are small diameter, bored, cast-in-place piles used to underpin structures. They were first employed over 40 years ago in Italy, and have been used in the U.S. since the late 1970's. However, it is only in the last few years that their full potential in terms of load holding capacity has been exploited: whereas 100 kip working loads typified former practice, ultimate loads approaching 700 kips have recently been recorded for Pin Piles founded in sand. In order to better understand the actual performance of these piles, fundamental research has been conducted by a consortium of industry and academia. This paper describes the advances made in the laboratory and full scale field testing programs. In particular, the extensive field tests have been conducted in a variety of materials in which different pile configurations have been cyclically tested to failure. By using this test method, the elastic performance of the piles has been examined and so the progressive interfacial debonding phenomenon has been studied. This has led to the development of the Elastic Ratio concept which is proving extremely useful in analyzing and predicting Pin Pile performance. Data are provided from the full scale Test Pile Programs conducted at Mobile, AL and Port Vancouver, WA. Given that Pin Piles are usually installed in areas of low headroom or restricted access, and through difficult, occasionally contaminated soils, the paper also describes key aspects of construction.

Jan 1, 1993

By L. McWilliams, L. D. Patts, J. D. Noll, S. E. Mischler

Elemental carbon (EC) is currently used as a surrogate for diesel particulate matter (DPM) in underground mines since it can be accurately measured at low concentrations and diesels are the only source of submicrometer EC in underground mines. A disadvantage of using EC as a surrogate for DPM is that the fraction of EC in DPM is a function of various engine parameters and fuel formulations, etc. In order to evaluate how EC predicts DPM in the underground mining atmosphere, measurements of total carbon (TC; representing over 80% of the DPM) and EC were taken away from potential interferences in four underground metal/non-metal mines during actual production. In a controlled atmosphere, DPM mass, TC, and EC measurements were also collected while several different types of vehicles simulated production with and without different types of control technologies. When diesel particulate filters (DPFs) were not used, both studies showed that EC could be used to predict DPM mass or TC. The variability of the data started to increase at TC concentrations below 230, µg/m3 and was high (>+20%) at TC concentrations below 160 µg/m3, probably due to the problem with sampling organic carbon (OC) at these concentrations. It was also discovered that when certain DPFs were used, the relationship between DPM and EC changed at lower DPM concentrations.

By W. D. Maier, H. V. Eales

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. A lithological and geochemical study revealed significant lateral variation of the interval over 170 km of strike, from about 30 m at the Union Section to 220 m near Brits. The cumulates also become more evolved and leucocratic with distance from the Union Section both towards the NE (Amandelbult) and SE (Impala, Rustenburg and Brits). It is inferred that the persistent heat flux from a putative major feeder zone near the Union Section impaired deposition of felsic cumulates in the vicinity, delaying crystallisation of successive phases in parts of the chamber near the feeder. New influxes were therefore deposited on a footwall of varying thickness and lithology in response to different degrees of crystallisation and accumulation along strike. The development of cyclic units of chromitite, harzburgite, pyroxenite, norite and anorthosite was interrupted at different stages in different parts of the chamber

Apr 1, 1994

By CHARLES L. WRIGHT

Coals may be divided into six classes-anthracite, semi anthracite, semibituminous, bituminous, subbituminous, and lignite. The first three cla~ can be distinguished by dHferences of composition, particularly the proportions of fixed carbon and the ratios of the fixed carbon to the volatile matter in the cools. The last three classes can be distinguished by di:fferences in physical character, chiefly in color and in manner of weathering. Lignite is brown, not black, and has generally a woody look, but it weathers in much the same way as subbituminous coals. On exposure to the air lignite slacks or crumbles. The lumps check and fall into small irregular pieces that exhibit a decided tendency to separate into extremely thin plates. Hence lignite deteriorates greatly during storage or long transportation. The most characteristic feature of the composition of lignite is a large percentage of moisture. '!his high moisture content reduces the fuel value of freshly mined lignite, and the partial evaporation of moisture, on expooure, causes th6 fuel to check and fall to pieces. Consequently, attempts to increase the efficiency of lignite as a fuel involve reducing its percentage of moisture and increasing its ability to endure storage and transportation. Both these results are accomplished by briquetting.

Jan 1, 1911

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognized and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economic restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist about application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2007

New Developments in Spirals and Spiral Plant Operations Records indicate that spiral separators have been utilised in mineral separation for over 100 years. The Spiral's predecessor, the sluice, has been in use for centuries in different forms and a spiral can be thought of as a sluice wound around a column. The spiral separator is distinguished from the straight sluice, and other flowing film separators, in uniquely introducing centrifugal motion. The elegance of the spiral concept was embraced due to significantly improved separation efficiencies, ease of operation and tolerance of variation in feed conditions. Advances in spiral technology have improved the metallurgical performance, modernised the materials of construction, increased unit capacities and simplified operation. These advances have ensured that spirals continue to play a major industry role amidst other advancing and competing technologies. Recent developments in spiral and spiral plant technology include: the launch of the VHG spiral model, specifically aimed at feeds with very high levels of high-density mineral particles; the introduction of a high capacity wash water spiral model; and innovations in feed stabilisation and control. Details of these developments are presented together with the resultant operational benefits including feed stabilisation, product control and improved metallurgical performances.

Sep 13, 2010

Senior staff representatives of the Bureau of Mines and the National Institute for Occupational Safety and Health (NIOSH) met in Washington on September 6, 1972, to review and evaluate their cooperative accomplishments to date and to consider the planning and conduct of future coordinated activities. The six presentations given at this joint staff seminar are published here for the benefit of those concerned with the problems of coal mine health, and especially those with responsibilities in administering the Coal Mine Health and Safety Act of 1969.

Jan 1, 1972

By K. S. Mortensen

The softwall mining system is a novel, new method of mining mineral deposits in soft, shallow, nonrock ground conditions. This method can mine the ore layer without substantially disturbing the existing overburden. The softwall mining system consists of machinery that is hydraulically controlled and powered, that can be buried (or used on the surface) to extract the ore or mineral from a layered deposit. The method is essentially an application of the longwall mining concept, modified for loose overburden and ore conditions, combined with hydraulic mining.

Jan 1, 2003

By Larry Patts, Jon Hummer, Jim Noll, Aleksandar Bugarski1, George Schnakenberg, Steve Mischler, Mike Crum, Shawn Vanderslice, Rick Anderson

This study is organized under the auspices of the Metal/Nonmetal Diesel Partnership formed by the National Institute of Occupational Safety and Health (NIOSH), the National Mining Association (NMA), the National Stone Sand and Gravel Association (NSSGA), the United Steel Workers of America (USWA) and the MARG Diesel Coalition. The ultimate objective of the study is to reduce the exposure of underground miners to diesel particulate matter (DPM) and gases, and to help in fulfilling the partnership’s goal of identifying technically and economically feasible controls to curtail particulate matter emissions from existing and new diesel powered vehicles in underground metal and nonmetal mines. The majority of current knowledge on the performance of the diesel particulate filter (DPF) systems and other control technologies is based on studies done under laboratory conditions, the results then being applied the results to on-highway vehicles. According to the best knowledge of the authors, only two comprehensive studies that were conducted recently at Noranda’s Bathurst Mining and Smelting Mine and International Nickel Company’s Stobie Mine under the sponsorship of the Diesel Emissions Evaluation Program [McGinn 2001, Bugarski and Schnakenberg 2001, Bugarski and Schnakenberg 2002] offered some insight into the problems associated with the deployment of modern DPFs to underground mining vehicles. The U.S. mining industry has expressed concern that this rather limited knowledge base is not sufficient to help them comply with the rule limiting DPM exposure of underground metal and nonmetal miners [30 CFR 57.5060 2001]. The partnership agreed that a series of comprehensive field evaluations of DPFs in several underground mines was needed to determine their viability of DPF systems and establish confidence in their performance. The first in this series of studies was the one conducted in Stillwater Mining Company’s Nye Mine, Nye, Montana. This study was conducted in two phases. The objective of the first phase was to establish the effectiveness of the selected technologies in reducing diesel emissions by using an isolated zone methodology. The objective of the second phase was to assess the effectiveness of diesel particulate filters in controlling the exposure of underground miners in actual production scenarios. As part of the first phase of the study a series of tests were conducted at Nye Mine from May 19, 2003 until May 30, 2003. The results of Phase I of the study are presented in this report.

Jan 1, 2005

By J. Talja

Keywords: drying, steam drying, concentrates, copper, lead During the past twenty years steam drying has become a prominent technology for drying of non-ferrous metals concentrate. This is mainly because of its low energy consumption and very low emissions. The first applications of significant capacity were stationary steam dryers, which however, faced severe challenges in maintenance costs and availability. That technology was soon replaced by Kumera?s rotary steam drying technology, which has been the dominant technology in new dryer installations world-wide for the past ten years, ever since the first installation in Hamburg in 1999. There are ten Kumera steam dryers in operation today and five more to be commissioned during 2011. Practically every dryer is different owing to continuous development, new innovations and operational experience with continuous feedback from the operators. Most significant improvements relate to capacity increase with the Kumera steam-dryer family, new feeder systems at the wet end, a completely new design of the dry material discharge with increased availability, heating element design and material selection, and control systems. This paper discusses the modifications and improvements introduced which have enabled the Kumera steam dryer to become the global leader in new dryer installations.

Jan 1, 2011

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979

By Sumner M. Anderson

Any discussion of outside support to Latin American mineral industries must concede at once the pre-eminent role of U. S. industry and business. American capital has developed the great copper resources of Chile and Peru, the lead-zinc of Peru and Mexico, the bauxite of Surinam and Jamaica, the petroleum and iron ore of Venezuela. American consumers have provided the market for their products. U. S. companies operating south of the border have trained Latin American geologists, engineers, chemists, and skilled labor—including metal, mineral, and fuel technicians—to new and greater competence. The industrial demands of World War II drastically altered world economics and concepts of U. S. foreign mineral requirements. In this country discovery of vital mineral resources fell far behind the alarming depletion rates, and there was new appreciation of the actual and potential importance of the world's less extensively explored areas. During the war and afterward, the task of supplying the nation's mineral requirements became greater than private industry could carry alone, and the Government assumed a position of continuing support. In Latin America, as elsewhere, this support applies in three categories: banking, procurement, and technical assistance. The first two are now generally accepted as necessary Government functions; the third has often been misunderstood and misinterpreted, although it has given rise to legitimate controversy. There have been major accomplishments in all three categories, as well as some errors of judgment. Since the beginning of World War 11, U. S. Government financing, procurement, and technical assistance have been applied on a large scale to a wide range of commodities and services throughout the free world. The present discussion—under the separate headings mentioned—will concern only the support related to a single industrial group in a single geographic area. During the War Federal banking was conducted on an emergency scale by temporary agencies created to meet the abnormal circumstances. Unfortunately, there are no readily available data on these activities that would permit evaluating loans and credits extended for mineral projects in Latin America. The only agency operating in this field since World War II is the Export-Import Bank, under its own authority and to some extent from credits authorized by the Office of Defense Mobilization. The Bank can offer more capital—on more favorable terms—than is available from most Latin American banks, and its staff of engineers evidently can appraise loan applications more favorably than commercial banks in this country are willing to do. The risks seem to be justified, as defaults have been well under 1 pct of total loans. From V-J day 1945 to the end of 1957, mineral loans to Latin America have been authorized for projects totaling $541.63 million in eight countries. In order of magnitude of credits, they have been made to Brazil, Peru, Chile, Mexico, Argentina, Venezuela, Guatemala, and Bolivia. In order of magnitude by industries. they are for development and expansion of steel mills, copper, manganese, nitrate plants, iron ore, zinc plants, sulfur plants, cement plants, tungsten, coal, and lead. Loan Distribution: By far the largest loans have been $307.9 million for iron and steel projects in Brazil, Chile, Mexico, Argentina, and Peru: $100.4 for developing the great low-grade copper deposits of southern Peru; and $55.3 million for developing manganese deposits in the Territory of Amapa, Brazil. Others range from $20.8 million for a zinc smelter in central Peru to $19 thousand for iron-mine trucking equipment in Chile. It has been noted that 59 pct of the loans have been to foreign companies, 14 pct to companies of mixed foreign and American capital, and 27 pct to American mining companies. About 40 pct of the total authorizations has been disbursed so far. In addition to these amounts, the Strategic Materials Division of the Economic Cooperation Admin-

Jan 1, 1959

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By Xuejing Xie, Tianxiang Ren

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). Standardised stream-sediment sampling procedures have been used in mountainous and hilly terrains. Special sampling procedures were developed for application in remote environments, such as high mountains, desert, semi-desert, karst and loess-covered regions. The diversified analytical methods used in more than 20 analytical laboratories participating in the project have been unified into two multi-element, multi-method analytical systems. A unified data monitoring procedure was developed based on primary and secondary standard samples. To date the project has covered about 4 000 000 km2 and the aim is to complete the coverage within the present decade

May 1, 1991