Search Documents

By I. A. Mwamba

Plain and alloyed titanium aluminides of composition Ti-47.5 at.% Al were prepared by melting commercial-purity titanium and aluminium with additions of 1 at.% precious metal. The as-cast alloys were subjected to potentiodynamic scans in 5, 15, and 25 wt% HCl aqueous solutions at room temperature and compared for their abilities to spontaneously passivate. Addition of precious metals resulted in a general improvement of corrosion resistance by increasing the open circuit potential to more noble values. Addition of 1 at.% gold or silver to titanium aluminide did not significantly increase the corrosion potential (Ecorr) above that of the plain titanium aluminide alloy, indicating that gold and silver are not sufficient cathodic modifiers to improve the corrosion resistance of titanium aluminide in all the solutions tested. However, platinum, palladium, and iridium additions shifted the corrosion potentials to the position of the passive region of plain TiAl for all solution concentrations. This indicated that TiAl alloyed with these platinum group metals would passivate spontaneously by cathodic modification. TiAl alloyed with palladium performed the best in 5 wt% HCl solution with the most positive corrosion potential. In 15 wt% HCl solution, alloys with platinum exhibited the most positive corrosion potentials, while alloying with iridium or palladium revealed more negative corrosion potentials. Thus, palladium alloying led to the best cathodic modification of titanium aluminide in low-concentration HCl solution, whereas platinum and iridium alloying additions resulted in the best cathodic modification of titanium aluminide in high-concentration HCl solutions.

Jan 1, 2013

By J D. St George

Flyrock is the unexpected and undesirable projection of rock fragments during detonation of a blast and managing this risk is becoming an increasing challenge as urban development encroach toward mineral extraction sites. The basic factors associated with flyrock are discussed in relation to geology, blast design and management. Published data of historical flyrock events are investigated and compared with local information on incidents. Good agreement was found between the data sets. A computer program of flyrock was developed using projectile motion based on launch velocity and angle, rock size, shape and density. This deterministic model was coupled with a probability model to simulate blast events. The impulse time ?t of the explosive pressure was taken as the stochastic variable to replace launch velocity. The variables were calibrated to replicate field data. A simulation was executed to demonstrate the capability of the approach to defining flyrock danger zones. For a simplistic situation it was identified that an appropriate distance to be cordoned off for the blast danger zone is a radius of 120 m in front of the blast and 65 m behind.

Jan 1, 2001

By Shachar Magali

This article describes two new concepts regarding the CFA (Auger Cast) piles. The first one, MALI Effect, is an approach to control the casting phase, while the second one, NETA Shear, is a technique which converts the drilling rig into a geo-mechanical tool. We look upon the system of the auger and the ground as a piston inside a cylinder. When concrete (grout) is pumped into that system, an up lift force is generated (We call that force MALI Effect). That up lift force reduces the needed tension in the pull up cable. By analyzing the tension force in the cable we detect the up lift force of the concrete. That pushup force is the product of the real concrete pressure at the bottom of the auger by the area of that bottom. As the area is known, the real pressure is accurately calculated. A control loop which is based on MALI Effect is very sensitive, precise, objective, reliable and easy to be used. All the process is based on pure real physical measurements. The system has no assumptions, no comparisons, no parameters, no zeroing and no adjustments. When we penetrate into the ground like a theoretical screw, for about a meter in depth, and then brake the main cable while rotating the auger, a set of forces generates. As the auger tends to keep penetration, but the cable holds it - a tension force develops (We call that force NETA Shear). Analysis of that tension force shows that it relates to the ultimate shearing capacity of the ground.

Jan 1, 2000

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions 5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1962

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchange-ability, and speed, it has become even more important. In spite of the supply of other abrasive and hard materials and of ultrasonic, electrospark rued other substitute grinding, methods, world industry seams likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting roes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determined the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has affected substantial savings.]

Jan 1, 1964

By Henry P. Chandler

[Diamond, because of its extreme hardness and abrasion resistance, has an important function in precision engineering and automation. With the increasing; requirements of modern production for fine tolerances, interchangeability, and speed, it has become even hors, important in spite of the supply of other abrasive and hard materials and of ultrasonic, electrospspark rued other substitute grinding methods world industry seems likely to absorb large quantities of diamond for industrial purposes. An increasing part of the world's needs will be supplied by manufactured diamond, which was introduced commercially by General Electric Co. in 1957. Use of diamond for glass cutting goes bark several centuries, mid diamond drilling of rock became important to the mining industry M the 1870's. Today, diamond drilling is the most extensively used method of exploring the world's ore reserves; diamond drills two also used to determine the nature of bedrock below the foundations of buildings, dams, and bridges. Diamond drill bits are now used extensively in the petroleum industry, and replacement or steel rock bits with diamond drill bits in hard rock formations has effected substantial savings.]

Jan 1, 1964

By M. M. Fine

Chalcocite flotation concentrates (26-34 percent Cu and 6-7 percent S) were roasted in air to determine sulfur elimination as a function of temperature, airflow rate, and residence time. Fluosolids roasting was evaluated batchwise and continuously in a 4-inch fluid-bed reactor. Kiln roasting tests were carried out in a 4-inch ID by 6-inch-long rotary drum. Pelletizing the very fine concentrates prior to roasting was essential to minimize dust losses and accretions. Concentrate pellets, sized minus 10 plus 20 mesh and bonded with 2 percent bentonite, were excellent feed for fluosol¬ids roasting and limited dust losses to 10 percent or less. One-fourth-inch pellets were best suited to kiln roasting. Both techniques were capable of producing copper calcines analyzing well under 1 percent residual sulfur when operated at 900° C with average retention times of 3 to 4 hours. Calcined pellets were strong, porous, and readily reducible.

Jan 1, 1970

By A. Normanton, B. Harris, V. Ludlow, S. Riaz

Why does a continuous casting mould powder, which works successfully on a particular caster with respect to semi quality, fail to perform on a caster of a similar design utilizing liquid steel from a similar route for an identical product without some tuning of its make-up and composition? In casting sequences of the same steel grade, why do some apparent random heats produce poor surface quality with respect to cracking when otherwise good surface quality is realized? The answer to these questions lies in the interaction of the mould powder, the casting hardware, and the casting process variables. Using, as examples, data collected from within Corus UK and during collaborative work on the assessment of mould powder performance and its effects on surface quality, the interaction of the mould powder, the casting hardware and the casting process variables is explored. The steelmaking route and its associated alumina load, unexpected changes to slag chemistry, infiltration of the slag into the mould strand gap, and the nature of the slag film are all shown to affect powder performance. Keywords: continuous casting, mould powders, alumina, slag films

Jan 1, 2004

By F. Dai

Due to difficulties associated with gripping in direct tension, indirect methods are commonly used to measure rock tensile strength. In this work, we adopt an innovative indirect tensile test method: Semi-Circular Bend (SCB) to measure the tensile/flexural strength of Laurentian granite (LG). The static tests are carried out with a servo-controlled material testing machine and the dynamic tests are conduced with a Split Hopkinson Pressure Bar (SHPB) system. Pulse shaping technique is adopted to achieve dynamic force equilibrium in SHPB to facilitate data regression. Finite element method is used to relate the failure load to the tensile strength. Strong rate dependence of the tensile strength is observed. The flexural strength is higher than the tensile strength measured using Brazilian Disc (BD). This difference is rationalized using the non-local theory. To further validate the method, a coupled Finite element/Discrete element method (Fem/Dem) in conjunction with the smeared crack model is utilized to simulate the fracture process during dynamic SCB tests. The resulting fracture patterns are qualitatively consistent with those from recovered samples. Both the experimental and numerical methods have validated the results and this new method is readily to be used for other rocks and other brittle materials.

May 1, 2009

By B. Das

he flotation studies on hematite were carried out using di (2-ethylhexyl) Phosphoric acid (D2EHPA) as the collector. The possible mineral reagent interaction was studied through electrokinetic and dissolution studies. The shift in zeta potential (PZC) and decrease in dissolution of iron in the presence of D2EHPA indicated that D2EHPA was specifically adsorbed on hematite surface. The adsorption imparted necessary hydrophobicity for flotation of hematite. Hematite could be floated selectively from hematite and quartz synthetic mixture. Key words: Hematite, D2EHPA, flotation, electrokinetics, dissolution.

Jan 1, 2003

[ ]

Jan 1, 2008

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

By F. H. McDowell

The increasing interest in the subject of electrical separation warrants the addition to what has already been written of a few lines covering the practical workings of the Tilly Foster mill under the direction of Mr. E. S. Moffat, General Manager. Since my last paper was presented to the Institute, Mr. S. P. Tomkins, the superintendent, has had thrust upon him for solution several problems complicated by the introduction of new conditions. 1. The richer portion of the lean ore dump, and that nearest the railroad track, having been worked up in 1890, the handling of the balance, including a largely increased amount of rock, could only be accomplished at an increased cost. 2. The tailings had accumulated close about the mill to such an extent that arrangements had to be perfected to move them further away.

Jan 1, 1893

By R R. Large

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The formation of orogenic gold deposits is commonly a two-stage process. The first stage involves preconcentration of gold in a suitable source rock, such as carbonaceous black shales, felsic volcaniclastics or komatiitic volcanics. The second stage involves the release of gold (commonly with arsenic and/or tellurium) from the source rocks during metamorphism or magmatic intrusive events, accompanied by the replacement of source rock pyrite by pyrrhotite. Recent research suggests that synsedimentary gold trapped in the structure of diagenetic arsenian pyrite in reduced carbonaceous facies of continental margin sedimentary basins is an ideal source of gold for many orogenic and Carlin-style gold deposits. The conversion of diagenetic arsenian pyrite to pyrrhotite during basin closure and greenschist facies metamorphism is the key process releasing gold and arsenic to the metamorphic fluid, with metal deposition in structural trap sites to form the deposits.CITATION:Large, R R, 2015. Orogenic gold deposits – a two-stage process of gold enrichment, in Proceedings PACRIM 2015 Congress, pp 335–340 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By O?Connor. D. F.

The ever increasing energy costs associated with mining at depth has become an important issue that needs to be addressed for future sustainable production. Vale Inco Limited?s Creighton Mine being the deepest has the highest energy cost per ton due to the ventilation system requirements. A review of the ventilation systems was undertaken with respect to current practices and identification of opportunities to the practical application of technology that would facilitate energy savings. Energy conservation initiatives such as time of day controls have been implemented; however there still remained some opportunity for further reduction. Based on previous studies that identified opportunities due to actual time spent in the workplace, our mining method and ventilation design, it was determined that Ventilation on Demand (VOD) could provide further additional energy reductions with respect to our auxiliary fans. A pilot project has recently been initiated to apply a Ventilation on Demand concept to two 112 kW auxiliary fans and their related workings located on the 2340m level of Creighton Mine. The project objective is to determine the practical methodology and application of this technology in the field. This project involves the installation of variable frequency drive (VFD) starters on the auxiliary fans to allow variable volume (through speed control) based on demand. The required flow is determined based on equipment and/or personnel via identification tags. The Fans adjust to the flow requirements as measured by flow sensors. Since the fans are sized for the final requirements the required flows can be achieved regardless of system length. Energy savings are realized by supplying only the volumes (power) as required and only when required. This paper discusses the rational and program being tested at the VALE Inco Limited, Creighton Mine.

Jan 1, 2009

Disasters are often tragic outcomes of high-risk technologies such as mines. In Australia, more mines are being developed every day, and the risk of disasters is ever increasing. No matter how effective our conventional safety devices are, there is a form of accident that is inevitable. These relate to accidents that result from æinteracting failuresÆ in a way that could not be foreseen by the designers. In so-called ætightly coupled production systemsÆ (processes that happen very fast, such as on a high producing mine) the risk is even higher and our risk controls mostly introduce some sort of a technological fix. While we are at the one hand attempting to control the risk, we are also introducing another level of complexity. Are we really controlling the risk? This is one of the fundamental questions that will be addressed in this paper: Do we have the ability within the mining industry and other industries to effectively prevent these catastrophes, or are we, on the contrary, faced with an increasing risk as a result of increasing complexities of our technology, management systems and practices. This paper will contend that perceived improvement in risk control is an illusion of activity, and that the likelihood of mining catastrophes may be exponentially increasing. Although the paper focuses on the mining sector many aspects may be applicable across a range of industries. This paper will further contend that we are applying the right solutions to the wrong problems. Our focus is technological and procedural, while our problem is one of production cultures ripe for error and failure.

Jan 1, 1999

By M. M. Singh, J. W. Brown

Three rocks of highly varied physical properties are selected for the first reported experimental study concerning microseismic activity of rock under tension to determine the effects of static fatigue, loading rate, repeated loading and rock anistropy compared to compression and bending loads. The microseismic method of detecting rock under deformation may be a great potential tool in surveillance and location in situ of dangerously stressed strata, as well as predicting rock failures. Noises emitted under load or the rate of energy (energy of noise pulses generated per unit time) are computed for varying conditions. The tests are conducted at constant load on a dead weight loading machine to eliminate all possible extraneous noises — an indispensable precaution — at various load levels. Experimental results are reported including the relation of total energy emitted to tensile strength of rock and the possibility of simulating a phenomenological model for microseismic activity. Plots of some of the experiments are included. INTRODUCTION Rock failure, whether on a large scale faulting in the earth's crust and rock bursts in mines, or on small scale ruptures of laboratory test specimens, generates transient vibrations in the rock mass. Mechanisms of intermittent deformation, such as twinning and cracking through and between mineral grains, also produce similar vibrations, but of very small amplitude. Such vibrations from both deformation and failure are referred to as microseismic activity, rock noise, or occasionally seismo-acoustical activity. An individual rock noise is sometimes

Jan 1, 1967

By A M. Purba and A Sjadat, A D. Wilson

Ongoing mining of the East Ertsberg Skarn System orebody below the Gunung Bijih Timur and Intermediate Ore Zone caves has been relatively successful and a ramp up to 80 000 t/d was achieved in the Deep Ore Zone Mine. However, the distribution of production, the overall drawpoint availability as well as the rate of change of the cave back profile has not followed the anticipated path. Several key factors influencing cave growth and progress, grade variation, fragmentation, wet muck and surface subsidence have been recognised over the life-of-mine that now have to be taken into account for planning the later stages of mining.The paper will discuss the influence of geological controls of lithology and structure – how this as well as other contributing aspects have impacted ore flow, contributing to some of the widespread panel damage, and been a key factor in compacted draw columns and caused an accelerated appearance of water ingress. This in turn has rapidly changed the distribution of wet drawpoints requiring remote mucking and special controls that also affect the call from the remaining dry drawpoints. Comment is also made on the potential final cave profile if it continues along the current trend and some discussion is offered about possible mitigation measures if this were to come about.CITATION:Wilson, A D, Purba, A M and Sjadat, A, 2016. Progressing cave performance into the later stages of the Deep Ore Zone mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 285–292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Robert T. MacMillan

An essentially chemical technique has been developed on a small scale for the efficient utilization of certain domestic titaniferous iron ores. Three main steps are involved: (1) Sintering the ore at 1,050° C. with carbon and soda ash to reduce the iron to metal powder, retaining the titania in the slag, (2) separating the powdered iron from the slag, after wet grinding, by magnetic or gravity methods, and (3) sulfuric-acid decomposition of the titania fraction to produce pigment and certain byproducts. The technique was first applied to the tailings from the Bureau of Mines bauxite-concentrating plant at Bauxite, Ark. A good grade of powdered iron was produced from this material. Subsequently, the work was diverted to the study of the titaniferous magnetite from the MacIntyre Mine at Tahawus, N.Y., because of the potentially higher recoveries of iron, titanium and vanadium. Ninety percent of the iron in this ore has been recovered as an iron powder analyzing 90 percent metallic iron and containing 2 to 3 percent TiO2. The remaining titania was found in the slag and was recovered as pigment-grade TiO2 by application of a suitable technique. The vanadium was distributed between the TiO2 fraction and the alkaline liquor resulting from the wet-grinding and magnetic-separation operations, with only a minor proportion retained by the metallic iron.

Jan 1, 1950

By Michael E. Stickney

"Soft technology" computers and computer programs-brings to mind a room full of machines, tape drives, disks, plotters, and printers spitting out financial reports. Computers now have a much broader scope of applications because of reductions in equipment size and cost. For example, people now interact directly with computers to control events. Such computers and associated equipment-called interactive control systems-are often small, relatively inexpensive, and can be designed to increase productivity at mining operations. This is accomplished by improving communications between individuals; giving employees the information needed to make decisions in real time, as events are happening; and giving individuals the background needed to perform more effectively. This paper will describe a procedure for determining the return on investment for interactive control systems, and describe four such systems. The analysis process is general in nature and can be applied to any type of mining operation or production process.

Jan 4, 1981