Search Documents

By R. Singh, M. Roy, D. Singh

Success of a blasting pattern in Blasting-off-the-solid (BOS) in Bord (Room) & Pillar method of coal mining is judged by the percentage of pull achieved vis-à-vis the yield of coal produced in a blasted round. Improper blast design and distribution of explosives in shot holes normally causes poor breakage i.e. a major portion of shot holes left unbroken resulting into reduced yield per blast. Over and above the disturbance to the roof is also due to excessive vibration caused by explosive energy not properly utilized in fragmentation.

Jan 1, 2003

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By Z. Lin, M. Isac, R. I. L. Guthrie

The kinetic and thermodynamic efficiencies of chromium recovery from the slag in an AOD process during the slag de-oxidation period with ferrosilicon is a complex process affected by slag basicity, temperature, the dissolution kinetics of the reducing agents, and intermixing of the slag/metal/alloy addition phases within the vessel. The present work focused on a study and simulation of the fluid dynamics and mixing behaviour of ferrosilicon additions in the AOD process for the production of stainless steel. In order to visualize the mixing behaviour, a two dimensional slice model of an AOD vessel was first built and filled with ZnCl2solution and then covered with silicone oil in order to represent the bulk liquid steel and slag phases, respectively. The injection of argon/oxygen process gases was simulated using air or helium. Particle trajectories and intermixing of the phases was monitored with a high-speed camera. To simulate the 75FeSi additions, glass spheres were used. A three-dimensional version of the AOD model was then constructed in order to confirm the adequacy of the slice model. Similar particle mixing behaviour was observed. Both models demonstrated that the ascending gas/liquid plume created two asymmetric mixing zones: a smaller rapidly re-circulating mixing zone adjacent to the side-wall locating the tuyere(s), and a larger mixing zone in the main part of the vessel. The process efficiency during the reduction period is governed by the thermal behaviour of ferroalloy as well as the mixing efficiency in the main large mixing zone. To enhance the recovery efficiency for chromium, small Fe-Si particles are suggested, given their wide distribution within the slag phase, and their large interfacial areas and rapid melting times for Cr2O3reduction from the slag. Keywords; modelling, ferrosilicon, chromium oxidation, AOD steelmaking.

Jan 1, 2004

By S. G. Hardcastle, C. K. Kocsis

"Worldwide, metal mines are going deeper. For example, in Canada there are six such mechanized mines planning production at 3000 m (10 000 ft). Working at such depths challenges all aspects of mining including the provision of ventilation to supply an equitable working climate for personnel and machinery.This paper explores the overall challenges of supplying ventilation in Canada’s deepest mines and how the volumes required could be minimized. This is essential because it must be remembered that ventilation and refrigeration are not only costly items to supply, but the magnitude of their cost is also very sensitive to the volume supplied. For the primary ventilation system this is obvious because of the cubic relationship between volume and cost.In deep mines, the main function of ventilation is the removal of heat transferred from the strata and generated by the mining machinery, and the air volumes supplied are designed accordingly. The second consideration is the removal of other pollutants that could be harmful to humans such as diesel and explosive fumes. However, the need for ventilation at its present design levels could be reduced. This paper discusses the implications of such technologies as: tele-remote mining and alternatives to diesel equipment on the magnitude of the volume supplied; ventilationon- demand which recognizes ventilation as a costly and limited resource; plus other aspects, such as the benefits of controlled recirculation, local cooling, and possibly heat rejection back to the strata to gain further advantage from new developments.Furthermore, this paper advances the need to be able to design ventilation systems more cost effectively and how such new advances as process simulators can be used in conjunction with ventilation simulators to explore the diverse options that could affect the air volumes required and provide more realistic economic data upon which to base design decisions."

Jan 1, 2004

By S. O. Bada

Fine phosphate feed is considered to be slime and normally disposed of as a discard in settling ponds or dumped as landfill. The purpose of this research was to establish whether commercially acceptable qualities and yields could be obtained from this material using dry separation methods. The results obtained from the electrostatic separation of <105 µm phosphate ore are presented. An existing separator was upgraded in order to improve on product and flotation concentrate recovery, to test different mineral, and to reduce particle residence time between the charging chamber and the separating zone of the separator. The operating conditions were varied according to the charges imparted to the particles in the electric field, and according to other device parameters. Parameters such as splitter position, charge reversal, rotation speed, charging voltage and separating voltage. The <105 µm phosphate feed was concentrated under both triboelectrification and inductive charging. The use of inductive charging and charge reversal resulted in a significant increase in grade for <105 µm phosphate feed, with the P2O5 grade increasing from about 12 per cent to 20.50 per cent, and a recovery of 26.30 per cent under a single stage of separation. It was found that better separation was achieved at rotation speed of 6000 r/min, -8 kV charging voltage, and 25 kV separating voltage.

Jan 1, 2012

By Holger Witthaus

There is more than a century of experience in multiple seam mining in Germany. In several mines up to 20 seams had been excavated within the last decades. Due to the nature of the deposit and the history of technical development the older panels cause a complex stress distribution for the lower seams and the current longwalls in descending order of mining. The depth of the longwalls reaches up to 4000 ft. This causes a maximum vertical stress that reaches between 30 and appr. 60 MPa. To handle these conditions several support systems are applied for roadway heading. A central knowledge management system for ground control is used for design and dimensioning of support within the DSK. This paper gives an overview to the nature of German multiple seam mining and the solutions in matters of panel layout and support design. It describes the full lifecycle for roadways in the seam starting with the geological and geotechnical evaluation, the basics of roadway deformation in great depth, the development of planning tools and standards for German coal mines, the range of alternative of support systems and roadheading techniques, as well as the reinforcement measures and the processing of support at the T-junction of the face entry. This paper uses exemplary descriptions that are consolidated in a specialized reference book ?Gebirgsbeherrschung von Flözstrecken? ? ?Ground Control in Roadways? which summarizes the standards of ground control based on the development of the past 25 years in German coal mines.

Jan 1, 2007

Research of 200 m3 Self-Suction Flotation Machine

Sep 13, 2010

By T. R. Paquin

Powerful, easy to manipulate, ventilation modeling software is readily available to most mining engineers. Too often when preparing an initial ventilation model, engineers will go overboard in their design, creating a complex model with hundreds of branches. When, in practice, the creation of a less complicated ?to the point? model, containing a few well-constructed branches, would have delivered the same results. In this paper the author will demonstrate, by using actual feasibility report examples, that when designing a ventilation model, engineers should make more use of the K.I.S.S. (?Keep It Simple, Stupid?) Principle. As mining industry consultants we must continue to improve on, and deliver timely and cost-effective results to our customers.

Jan 1, 2009

By Kirstin Girdner, Tom BoBo, Brian Norton, John Kemeny

Split Engineering is a truly customer oriented company dedicated to providing quantified fragmentation information of the highest integrity to enable process management and control. Technical decisions, blasting costs, operational efficiency and productivity and equipment performance can all be related to optimum fragmentation. In the past, the lack of an easy, non-disruptive, economical measuring technique has meant that, in most cases, rock fragmentation has not been defined in quantitative terms. Now, the Split-Desktop@ software provides an economical alternative to manual sampling and screening and an objective measure rather than subjective qualitative estimates. This workshop will present the latest features of the Split-Desktop@ software and show users how to quickly get quantifiable results from their blast fragmentation. A step-by-step demonstration will display the software’s flexibility, user-friendly options, and ease of use. Outlining where other mines have benefited from using the Split-Desktop@ software will provide insight to a wide range of software uses and potential applications like creating a database of geologic zone specific post-blast fragmentation information, underground draw point monitoring, stockpile, leach pile, and waste dump size measurement and monitoring, as well as many other applications.

Jan 1, 2000

The Pogo Mine, near Delta Junction, Alaska is a 2500 TPD gold operation employing processes including grinding, gravity, rougher flotation, leach, CIP, and E/W. An OCS(Optimizing Control System) expert control system has been implemented on rougher flotation in early 2008. The OCS system communicates with the Plant DCS(Distributed Control System) through OPC(OLE for Process Control) communication. The initial strategy was to control the flotation cell froth level set points to achieve target froth velocities. This strategy was enhanced by controlling both level and air flow setpoints. The flotation cell air and level are adjusted to reach cell pulling rates (froth velocities). The pulling rate setpoints for each cell are determined based on downstream capacity (concentrate surge tank level). The effect of pH and upstream disturbances is also taken into account in adjusting the air and level setpoints. Feed forward compensation is employed down the flotation row to minimize disturbances.

Jan 1, 2009

By K. Nasrallah

"The Dumont deposit is a large (1,179 Mt proven and probable reserve) low grade (0.27% nickel), nickel sulphide project located in the Abitibi region 25km west of Amos, Quebec. Royal Nickel Corporation acquired the project in 2007 and has since taken the project from a scoping study in 2010 through to completing the feasibility study in July 2013.The Dumont deposit in a nickel deposit with the recoverable nickel contained in three minerals; pentlandite, haezlewoodite and awaruite. The minerals are recovered by a combination of flotation and magnetic separation. Over the course of the studies many flowsheet design decisions and changes were made. This paper outlines an overview of the project, flowsheet design including the comminution circuit, desliming and awaruite recovery. The overall resulting flowsheet that was used for the feasibility study is then presented along with the confirmatory locked cycle testing that showed the feasibility design basis was able to produce the predicted concentrate grade and recovery.IntroductionRoyal Nickel Corporation (RNC) is a mineral resource company headquartered in Toronto, Canada, primarily focused on the exploration, evaluation, development and acquisition of base metal and platinum group metal properties. RNC's principal asset is the Dumont Nickel project (Dumont project) located in the established Abitibi mining camp, 25 km northwest of Amos, Quebec. RNC acquired a 100% interest in the Dumont property in 2007. The mineral claims covering the Dumont deposit are currently held 98% by RNC and 2% by Ressources Québec.The Dumont project is located in the province of Quebec in the municipalities of Launay and Trécesson approximately 25 km by road northwest of the city of Amos, 60 km northeast of the industrial and mining city of Rouyn-Noranda and 70 km northwest of the city of Val d’Or."

Jan 1, 2016

By D. R. Wilburn

The worldwide budget for nonferrous, nonfuel mineral exploration was expected to increase by 58 percent in 2004 from the 2003 budget, according to Metals Economics Group (MEG) of Halifax, Nova Scotia. The increase comes two years after a five-year period of declining spending for mineral exploration (1998 to2002). Figures suggest a subsequent 27 percent increase in budgeted expenditures from 2002 to 2003. For the second consecutive year, all regional exploration budget estimates were anticipated to increase. The worldwide budget for gold exploration achieved about 50 percent of the total amount budgeted in 2004.This was 68 percent, or US$715 million, higher than the reported 2003 budget. The 2004 worldwide exploration budget estimates for copper increased by 70 percent, orUS$237 million, to US$577 million from the 2003 budget. The budget for nickel exploration increased 52 percent, or US$89 million more than in 2003. The 2004 exploration budget for other mineral targets (primarily cobalt, heavy minerals, industrial minerals and silver) increased114 percent, or US$118 million.

Jan 1, 2005

By Michael R. Walsh, John H. Wright, Eivind B. Jensen

A tunnel boring machine (TBM) was designed and built at the Cold Regions Research and Engineering Laboratory in 1992 for use in Antarctica. The TBM system was tested at the South Pole where a 120-m long tunnel was bored to prove the concept. Modifications were made to the system resulting from this work. In 1999,boring of a 600-mutilidor began as part of the new South Pole Station. Tunneler hydraulics reliability problems prevented the completion of the tunnel before the end of the short construction season. This paper discusses the design and operation of the TBM, proposed solutions to the problems encountered, and current operations of the system.

Jan 1, 2001

By M. Kane, B. Bissonnette, D. Hodouin

"A laboratory cell has been designed for a careful investigation of gold ore cyanidation using mathematical modelling of the process kinetics. The cell is a stirred vessel with continuous monitoring and control of pH, oxygen and free cyanide contents. Samples are automatically extracted for gold analysis. The instruments are connected to a microcomputer which records all the measured variables and calculates the reagent consumption (air or oxygen, cyanide, lime). For cyanide control a sample is automatically extracted and filtered and the solution analyzed, using a specific electrode, by a flow injection technique. The rate of gold dissolution is modelled using a kinetic model the parameters of which are calculated by a non linear least-squares technique. The parameters of an empirical model of reagent consumption are also estimated. The resulting model is used in a simulator for gold cyanidation plant design, tuning and control.INTRODUCTIONThe leaching of gold ores in a cyanide solution is the usual method for gold extraction from raw ores. This process requires long reaction times and leads to very significant consumption of cyanide. The optimization of the cyanidation plant operation is a very important aspect of gold ore processing for increasing gold recovery and decreasing operating costs. The key parameters to the improvement of gold extraction are the selection of an efficient solution chemistry, the design of the size and the arrangement of the equipment and the correct tuning of the operating variables. Automatic control strategies can then be applied to maintain industrial operations at their optimum setpoints.Two approaches can be used for optimizing design and control of cyanidation circuits, either empirical trials for improving process performances or mathematical modelling of the process kinetics for subsequent analysis, simulation and optimization. The advantages of the second approach, which is used in this study, is that it gives a systematic pattern to interpret data and reliable tools, in as much as the models are good, to improve operation performances. In order to determine the structure and the coefficients of cyanidation models, well controlled measurement and calibration procedures must be used. The purpose of the paper is to present an equipment and a test procedure for modelling the kinetics of gold ore cyanidation."

Jan 1, 1990

By K. Delbeke

Within the framework of the EU Existing Substance (93/793/EEC) and REACH regulations EC/1907/2006), the copper industry initiated in 2000 a comprehensive Voluntary Risk Assessment of copper and several copper compounds. The Italian Government&apos;s Istituto Superiore di Sanità, reviewed the process and reports on behalf of the European Commission. Copper exposure levels to man and the environment from production of copper anodes and cathodes, copper powders and copper chemicals as well as fabrication and use of semi-fabrication products and down stream user products were collected across Europe. Environmental and human health effects data were obtained from literature as well as novel research programs and used to deduct safe threshold

Jan 1, 2007

By S. C. Tennant, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Immobile-element lithogeochemistry is providing a detailed chemostratigraphy of the submarine Ordo-Silurian volcano-sedimentary sequence. Primary lithologies and magmatic affinities of the sericitised and silicified volcanics are determined from binary plots of Nb, Zr, Y, TiO2 and Al2O3, while mass-change calculations using immobile-element anchors can identify and quantify zones of significant hydrothermal alteration. Stratiform polymetallic mineralisation at the western margin of Parys Mountain, around the Penymynydd fault zone, has been shown to have a distinct hanging-wall and footwall stratigraphy. These ore zones are probably part of a homoclinal, north-younging volcano-sedimentary sequence. The apparent stratigraphic complexity results from primary lithofacies variations and pervasive alteration, with the modifying role of the Caledonian orogeny much less than previously suggested

Jun 19, 1905

By Jasper L. Stuckey

PYROPHYLLITE, first identified as soapstone,1 later as agalmatolite,2 and finally as pyrophyllite,3 has been known to occur in North Carolina for more than 130 years and has been produced intermittently in commercial amounts for the past 100 years. Pyrophyllite mining, however, has become a major industry in North Carolina only during the past 25 years. North Carolina and California are the chief producing states. Current annual production averages 125,000 tons, of which slightly more than 90 pct comes from North Carolina. Distribution and Geologic Setting: All known pyrophyllite deposits in North Carolina are associated with rocks of the Carolina Slate Belt,4 which is composed of a vast series of metamorphosed volcanic and sedimentary materials, occurring as two zones extending in a northeast-southwest direction across the state. The larger of these zones, lying in the central Piedmont region, varies from 8 to 50 miles wide. The smaller zone lies along the eastern edge of the Piedmont region and is partly covered by coastal plain sediments.

Jan 1, 1958

By Christine Hansen

?Kiss my Asteroid? Unofficial Title Human life is tied to minerals It?s worth noting that: The living human body consumes minerals. The minerals we take in multivitamins show the close linkage between human beings and mineral resources. Unlike tourism or specialized manufacturing, a human being could not live without mineral consumption. Minerals and their consumption is a tangible part of human life.

May 1, 2013

By W. L. Ott, J. E. Hawley, C. L. Lewis

"IntroductionTHE APPLICATION of spectrochemical analysis to metals of the platinum group was advocated by Harvey (3) as follows: ""The spectra of the platinum group metals have been studied less than many of the more common metals. The rarity of occurrence of these elements makes the analysis relatively unusual. Potentially, the analysis of this group is an excellent application of spectrographic methods, particularly in contrast to the tedious chemical procedure"".Wichers (8) divides platinum-metal analysis into three broad divisions as follows :( 1) The detection and estimation of these metals in other materials, e.g., ores, where the amounts present are very small.(2) The detection and estimation of impurities in the refined metals themselves ....(3) The analysis of alloys of the platinum metals .....The present paper deals with the second division: analysis of refined rhodium.Research on spectrochemical techniques for determination of trace contaminants in refined platinum metals was begun at Queen's University in 1949, under the supervision of Professor J. E. Hawley. Since 1953, the work has been continued in the Metallurgical Laboratories of Falconbridge Nickel Mines, Limited. Techniques for spectrochemical analysis of refined platinum and palladium have been published ( 4, 5). A technique for analysis of refined iridium has been developed but not yet published."

Jan 1, 1955