Search Documents

By A. Choudhury

Deep open-pit mines are becoming increasingly common in the highly mineralized arctic and sub-arctic regions. Air inversion is a frequent occurrence in these regions, and is exacerbated by the natural topography of an open-pit mine. Due to such inversions, the air quality in open-pit mines deteriorates very rapidly. Transport of gaseous pollutants under arctic air inversion is complex and involves an interaction between flow, thermal and convective transport systems. This paper discusses the construction and validation of a three-dimensional model that simulate the flow of air and the transport of gaseous contaminants in an arctic open-pit mine and the effect of low influent velocity and large gust velocities on the contaminants profiles in the mine. It was found that while higher velocities may remove contaminants from the pit bottom, they may not remove the contaminants from the pit entirely, necessitating artificial mitigation measures.

Jan 1, 2012

By EDWARD B. DURHAH

(San Francisco Meeting, UCtober, 1911.) THE refinery at the San Francisco Mint takes the bullion purchased by the receiving department, and carrying more than 200 parts of precious metals in 1000, or, in mint parlance; over 200 fine, and separates and refines the various metals contained therein, using electrolytic processes exclusively. Bullion containing silver is treated in cells charged with a nitric electrolyte. These cells produce fine silver and leave a residue rich in gold. The residue from the silver-cells, together with crude gold-bullion, is treated in cells having a chloride electrolyte. These produce fine gold and leave a residue containing silver chloride. The latter is reduced to the metallic state with zinc and is then treated in the silver-cells. The various waste solutions and the wash-waters, after being freed from the bulk of their precious metals, still contain copper and other metals. These are removed by scrap-iron, and are then treated in the copper-cells, having a sulphate electrolyte. These cells produce pure copper, and collect a residue containing lead, some gold and silver, and all the metals of the platinum group that were in the bullion. This residue is relatively small, and is melted into bars and stored until sufficient accumulates to warrant treating it for platinum, etc. The refinery occupies three large and three small rooms. The large ones are, a melting-room, 30 by 34 ft.; a cell-room, 39 by 46 ft.; and a wash-room, 30 by 33 ft. The small rooms are used as foreman's office, laboratory, and generator-room, respectively. The methods here described are those in use in December, 1909, when notes for the present paper were taken.

Oct 1, 1911

By Enzo Palumbo, Joël P. T. Kapusta, François Larouche

In light of the rapid deployment of bottom blowing smelting in China over the last ten years, one has to wonder why it has taken the copper industry so long to adopt ultra-high oxygen enrichment via Savard-Lee type injectors. As early as 1976, Kellogg and Henderson suggested, in their landmark paper on energy usage in the copper industry, that ‘maximum use of oxygen enrichment of process air’ was one of seven ‘energy saving features’ for copper matte smelting and converting. Yet today, shrouded injection and high oxygen enrichment has not been implemented in copper bath smelting outside China and Vietnam. In this paper, the authors explore the reasons why bath smelting processes such as the Noranda Reactor and the Teniente Converter still operate around 40% oxygen enrichment, while the bottom blowing SKS/BBS process typically runs at 65 to 75% oxygen, with all three processes producing white metal. Are there fundamental metallurgical explanations for this striking difference beyond the long-standing skepticism towards high oxygen shrouded injection and its perceived high implementation cost?

Jan 1, 2015

Discussion of the paper of R. J. COLONY, presented at the New York Meeting, February, 1921, and issued With MINING AND METALLURGY No. 169, January, 1921. R. J. COLONY (author's reply to discussion).-The work of Sosman and Merwin on the system lime-ferric oxide, mentioned by Mr. Rankin, was not overlooked. When studying portland cements and portland-cement clinkers petrographically, however, the lime-iron compound was difficult to correlate with the very definite dicalcium ferrite described by those investigators, which possesses such well-defined optical properties. In portland cements, the calcium ferrite (or ferrate?) is an indefinite, fuzzy, and generally amorphous, or apparently amorphous substance that is distributed interstitially with respect to the other grains, from which it was very difficult to derive any satisfactory results. For this reason, the writer, tentatively, chose to regard it as related to the aluminate, and assigned to it the composition 3CaO.Fe203, which may be incorrect, however, as Mr. Rankin suggests.

Jan 8, 1921

By Alicia O'Reardon

DIFFIDENTLY, because don'ts are rarely greeted with cheers; humbly, because I, myself, have never lined up with the irreproachables, I venture on the subject of manners for the mining camp matron. Mining camps can be divided roughly into two types-the large, opulent settlement that blooms like the rose about a strong mine in full operation; and the puny group of adobe huts, or calamina shacks, or even canvas tents flung down in the wilderness to shelter the gay pioneers of a shining prospect or the shattered survivors of a lost hope. Of the first, I know nothing; but in the second, I have spent some of my best years, and from its curious code of morals and manners, its comic hates and its unreasoning loves, its high impatience and its engulfing kindness, I have charted the narrow .and pitted path which must be trod by the woman who would success¬fully live therein.

Jan 1, 1936

By Jack L. Henry

The ternary system A14C3-AIN-Al203 has been examined to determine compositions which may display desirable high-temperature refractory properties. Powder methods were employed in the synthesis of all test compositions. Forming and sintering behavior was examined and hot-pressing parameters were measured. Several properties were studied for each composition of interest in the system. The properties included hydrolysis rate in moist air, elevated temperature oxidation rate, density, softening point, tensile strength, and rupture strength. In most cases equilibrium was not achieved, and the data are representative of a nonequilibrium system. Approximately 16 separate phases have been observed in the system. Forming behavior and selected properties of five compositions of interest were compared with those of aluminum oxide and aluminum nitride. None of the compositions compared favorably. Oxidation and vaporization appear to be serious drawbacks to the use of these compositions at elevated temperatures.

Jan 1, 1969

By C. W., Davie

"DEFINITIONDiatomaceous earth consists almost entirely of the silicious remains of minute flowerless aquatic plants known as diatoms. The name diatomaceous earth, therefore, is to be preferred to others such as trade names, inappropriate terms, or names correctly applied to some other product. The following names should, therefore, not be used for diatomaceous earth,-- kieselguhr, infusorial earth, diatomite, celite, moler, bergnehl, English rottenstone, tripoli, tripolite, fossil earth, desmid earth, white peat, tellurine, randanite, ceyssatite, or any trade name.FORMATIONDiatoms live in practically all kinds of water, fresh or salt, hot or cold, still or running and under different conditions of depth and pressure. These minute plants assimilate inorganic salts from their environment and produce skeletons of silica much as mollusks secrete lime and form their Shalls. When the diatoms die they settle to the bottom together with anything else which may be present, such as sand, clay or volcanic ash. The organic matter gradually disappears leaving the silicious skeletons of the diatoms which, with impurities, make up the deposits of diatomaceous earth. These deposits which are still being foamed at the present time and which were produced throughout very different epochs, were more prolifically formed in the Tertiary, so that the thickest beds so far discovered are of that Age."

Nov 1, 1925

By J. E. Hoffman

The operation of the U .S Metals Refining Company, USMR Co. is defined below by the description of a variety of unit processes and operations the author encountered during his tenure with the operation, 1955 - 1978. The operations discussed include: sampling and sweating of radiators, processing of Indian Coin, treatment of insulated wire, baghouse and converter dust treatment, blast furnace and converter operation, the electric arc furnace, antimony control, selenium and tellurium products, electrolyte liberation with soluble anodes, and the precious metals refinery. These operations, although peripheral to the primary copper production circuit, were critical to the company's technological and economic base.

Jan 1, 2000

By L Edwards, M Haest, D Mittrup

The focus in the iron ore industry has shifted from increasing production volumes with less regard for cost, to efficient production of quality tonnes. BHP Billiton iron ore geoscience and exploration has embedded infrared spectroscopic sensing of drill hole samples to help meet this challenge.Infrared spectroscopy is delivering mineral predictions that are used for (automated) geology logging and modelling. The spectra are processed together with other available data sets to predict geometallurgical and geotechnical variables that include lump per cent and uniaxial compressive strength.Trials are ongoing to test the benefit of infrared spectroscopy during mining, including the analysis of grade control samples and remote sensing of mine faces. Results show great benefits in the fields of short-term geology modelling, better understanding of material (handling) properties, identification of geotechnical risk areas and high resolution ore-waste delineation.These trials are bringing BHP Billiton iron ore closer to its ultimate goal of having infrared spectroscopic data collected across the mining value chain. Once such data are available everywhere, regression models can be trained at one point (eg iron grade model trained on exploration samples) and be applied elsewhere (eg iron grade predicted on mine faces). Such predictive analytics will enable not only high precision mining, but also provide maximum time to tailor plant design to the ore in the ground, based on learnings from ores processed in other plants. This will improve planning outputs that will eventually increase mining efficiency, processing capability and product quality.CITATION:Haest, M, Mittrup, D and Edwards, L, 2017. Infrared spectroscopy in BHP Billiton iron ore with a focus on in-mine infrared sensing, in Proceedings Iron Ore 2017, pp 549–556 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By C. H. Schack

Extractive metallurgy techniques currently employed to recover silver from primary ores and secondary scrap were reviewed and evaluated to identify and delineate metallurgical problems whose resolution would increase the supply of silver from domestic materials. The survey revealed that practically all primary silver is recovered by froth flotation concentration of various types of ores, followed by smelting and refining of the separate lead, copper, and zinc concentrates. Silver losses during the complex processing are, with rare exception, inconsequential. Furthermore, any silver production gain from base metal ores, which contribute about two-thirds of the total primary silver, is directly dependent in improvement in the market for the base metals. Statistical data on new and old silver scrap are wholly inadequate to make reliable conclusions about scrap processing problems and the possibility of increasing the recovery of silver from the many forms of secondary silver- bearing materials. The available information indicates (1) that efficient silver reclamation practices are employed by the larger users of silver, and (2) that recovery of additional secondary silver involves solution of problems of collection rather than of processing. Several possibilities exist for limited increases in silver production from primary ores by improvement in metallurgical practices. Specifically, research is needed to (1) solve the problem of recovering silver from the copper ores of the Copper Range district, Michigan; and (2) devise economically feasible methods for recovery of silver from presently marginal or submarginal ores that because of grade, location, and frequently complex nature cannot presently be exploited by conventional techniques.

Jan 1, 1965

By Heinrich Ries

I. INTRODUCTION. THE facts is presented in this paper, based chiefly on recon¬naissance made, during the summer of 1903, by myself and my assistant, Mr. R.. C. Brooks, cover practically all that portion of Texas lying east of the 99th meridian. The work was undertaken for the University of Texas Mineral Survey, and was to have been extended over the entire State, but the sudden termination of the survey prevented even the official publication of the results already obtained. Most of the mineral resources of Texas were fully treated by the First Geological Survey, but the clay-industry was tit that time little developed, so that only a few scattered notes concerning it are to be found in the Survey reports. The extensive exploitation of the clay-deposits, however, has emphasized their commercial importance, and has also made accessible many facts of exceptional interest concerning their geologic conditions. The erection of new plants for the utilization of clay-products is usually preceded by more or less prospecting, which, by reason of the scarcity of outcrops, and the geologic and topographic conditions of eastern and southeastern Texas, is often slow and difficult work. This is especially true in the Tertiary and Pleistocene areas, where the structural conditions much resemble those of the Atlantic coastal plain, the deposits being mostly lenticular in form, and surrounded by beds of sand. II. GENERAL GEOLOGY OF THE CLAY-DEPOSITS. The accompanying sketch-map, Fig. 1, shows the location of nearly all the deposits examined, their relation to the geology of the State, and the type of clay found in each. The geology is based on the published work of Hill, Cummins, Tail, Adams, Hayes and Kennedy, but the boundaries have unfortunately not been determined over the entire region covered by the map, and, in many areas, are only approximate. It will be seen that the clay-deposits range from Carboniferous to Pleistocene in age, the older deposits being found in the northwestern part of the area, while those of Cretaceous and Tertiary age lie to the east, southeast and south. The Pleistocene clays are found in part in a belt along the coast, and in part along many of the larger rivers, where they often underlie extensive terraces.

Sep 1, 1906

By M. Ataee-pour, S. E. Jalali

So far, a large number of algorithms have been developed for the optimization of pit limits, most of which follow deterministic rules. In this paper, a new algorithm is introduced, which follows a probabilistic logic using the Markov chain process. The algorithm is implemented on a transition matrix that corresponds to the 2D conventional economic block model of the mining area. The probability of mining a block is proportional to the desirability it may provide. Applying this algorithm, the probability of mining each block is obtained, and finally, the optimum pit limits are defined as the pit, which provides the highest probability of mining. In order to validate the proposed model, a numerical example is given and the results of the algorithm are compared to those of a dynamic programming algorithm. A 2D analysis of the problem is discussed in this paper. Although dealing with 3D problems requires larger size matrices, the optimization method is the same and the algorithm does not need any smoothing.

Jan 1, 2006

By S. H. Lorain

This paper, which describes lode gold mining in Idaho county, Idaho, is one of a series on western mining districts being published by the Bureau of Mines. It describes mining and milling practices, gives costs, and discusses transportation, climate, power, labor, and other conditions that affect them. The materiel upon which the paper was based was gathered during a field survey in the summer of 1937.

Jan 1, 1938

By James T. McCartney, Joseph D. Davis

For more than 10 years coke-oven technologists have been investigating the expanding properties of coal on a scale larger than that afforded by laboratory test tubes. Koppers 4/ was among the first to realize that coals can not be differentiated satisfactorily with respect to expansion in coke ovens by the simpler test-tube methods; in his first method 80 grains of fine coal were coked in a cylinder heated from the bottom, so that the zone of fusion (plastic layer) advanced from the bottom to the top. The scale of test was too small; it has been modified by other investigators, but without significant improvement in practical application of the results. Somewhat later Koppers and Jendne 5/ experimented with a small-scale coke even, one wall of which was movable, in which the layer-coking in a coke oven could be simulated closely. This oven was heated from both sides. Their results with this oven showed a peak in the time-pressure curves near the end of the coking, period when the two plastic layers, advancing from opposite walls, meet. They also found that although the smaller oven was heated from one side only and did not show the Pressure peak characteristic of two-sided heating, it still gave results entirely too high. Russell built an oven similar to the movable-wall oven of Koppers and Jenkner and compared results obtained in it on Beckley expanding coal with these obtained on the some coal in the Altieri 7/ small-scale apparatus. Both tests were conducted at the same constant pressure, but heating was from two sides in Russell's oven and from one side in the Altieri tester. Russell found that the two types of test gave comparable results under constant pressure conditions even though the heating procedures were quite different. He showed later, however, that a "borderline" coal 8/ that contracted in the Altieri tester at constant pressure developed a peak pressure of 4 pounds per square inch in the movable-wall oven heated from both sides at constant volume. He concluded from this that testing at constant volume gave results more accurately indicative of dangerous expansion tendencies than those at constant pressure. He also found that heating from both sides in this oven gave higher pressure than heating from one side only.

May 1, 1942

By Robert S. Hill

"In November 1942, a preliminary report on the Swartz Mining District by John H. Soule, an engineer of the Bureau of Mines, recommended an exploratory program of diamond drilling. The existence of zinc and lead deposits in this region had been known for many years. In 1943 and 1944, the Federal Geological Survey made a detailed study of the same area. Later work done by the Bureau of Mines in this district followed the suggestions made by these geologists.3/In the latter part of 1944, Felix A. Vogel, Jr., another Bureau engineer, made a study of the Grey Eagle mine in the Kingston Mining District, a few miles northeast of the Swartz district, and his recommendations for diamond drilling were followed in so far as funds permitted. Drilling was started in October 1943 and was completed in June 1945.4/In its program of exploration of Mineral deposits, the .Bureau of Mines 'Ms as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution t national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, special acknowledgment for assistance is due to C. H. Johnson, chief of the Rolla Division, Mining Branch, and to various members of the Geological Survey."

Sep 1, 1946

By Hamid Maleki

Prudent design of coal pillars in any mining system requires an estimation of in-situ pillar strength, overburden lateral load transfer capability, and a failure criterion. Pillar strength is typically determined using one of several different empirical pillar strength formulas. For coal reserves in the U.S., a new pillar design method was proposed based on extensive U.S. field measurements in underground mines (7) which accounted for confinement effects. Field measurements in seven U.S. seams indicated highest strength for some Utah mines where the coal seam developed high confining stresses. Lower strength was measured in structurally controlled seams. This method is expanded here including the data from the weaker tertiary coal measure rocks and lower confinement for pillars with low width-to-height ratios. The determination of how much load a pillar is expected to take is partially dependent on the ability of overburden to transfer load laterally; this is useful for selection of panel width and barrier pillars size in select mining applications where long-term stability is required in conservative designs. In caving mining systems, caving of the strata is influenced by geologic, mining and stress conditions and the released energies influences how the pillars react at loads approaching pillar strengths. Overburden deformation and caving mechanisms are analyzed in this paper in multi-panel extractions to enhance the understanding of load transfer, seismicity and coal bump control in deep western U.S. operations.

Jan 1, 2008

By Shemek Oginski, MARK C. JOHNSON

All Rights Reserved. Printed in the United States of America. Information contained in this work has been obtained by SME, Inc. from sources believed to be reliable. However, neither SME nor its authors guarantee the accuracy or completeness of any information published herein, and neither SME nor its authors shall be responsible for any errors, omissions, or damages arising out of use of this information. This work is published with the understanding that SME and its authors are supplying information but are not attempting to render engineering or other professional services. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of the publisher. Any statement or views presented here are those of individual authors and are not necessarily those of the SME. The mention of trade names for commercial products does not imply the approval or endorsement of SME.

Dec 1, 2015

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970

By P. K. Chatterjee, G. D. Just

Sublevel open stoping is a low-cost method that has been successfully employed in many large underground mining operations. Where ore body characteristics are suitable, extensive mechanization and the use of large-scale stoping techniques can considerably reduce operating costs. However, careful long-term planning of mine layouts and large capital commitments in development are required prior to production. Implementing precise mine design procedures and carefully controlling operations can result in considerable benefits. This article describes methods to achieve these objectives based largely on mining operations at Mount Isa, where sublevel open stoping has been used since 1932. Ore won by this method accounted for a very large percentage of the total tonnage produced at Mount Isa. Major costs associated with sublevel open stoping can be classified as drilling, explosives and charging, and LHD costs. In this article, analyses of these costs are made with particular reference to stope design. Parameters such as burden, drill hole diameter, explosive density, specific charge, etc., are considered in establishing the interrelationship of unit operating costs, as well as total costs of sublevel open stoping.

Jan 10, 1981

By Jesse A. Miller

ALTHOUGH the element titanium was discovered by William Gregor in 1790, over a hundred years passed before it was put to commercial use. The first commercial application of titanium was as an alloy additive to iron and steel, and the first ferroalloys were produced domestically in 1906. Titanium pigments were developed somewhat later and have been produced in the United States since 1918. The use of titaniferous material in welding-rod coatings first gained acceptance ill the mid-30's. The metal titanium has only had commercial importance since 1948; domestic production for that year was 10 tons. The relative importance of these major uses of titanium in various forms may he gaged by the consumption of titanium dioxide (Ti02) for these purposes in 1954. Of a total of 440,000 short tons of Ti02 consumed in 1954, 95 percent of the total was consumed for pigments; 2 percent for welding-rod coatings; 1 percent for non-titanium-base alloys and carbide; and 2 percent for miscellaneous uses. The titanium-metal industry is in its infancy, but it has more than doubled its output every year from 1948 to 1954, reaching 5,370 short tons in 1954.

Jan 1, 1957