Search Documents

By C. Sawmliana

Deep-hole blasting operations in opencast mines are always associated with some annoyance to the surrounding areas in terms of ground vibration, noise, flyrock, etc. These become more severe when underground mines run parallel to them. Blasting in opencast mines may pose danger to the underground mines in terms of roof/side failures, damage of water dams, isolation/ventilation stoppings and other underground installations. The paper discusses a case study in India on the impact of deep-hole blasting in Ramagundam Opencast Project ? III on the stability of various water dams of GDK-6B Incline coal mine operating in close proximity. The stability of underground water dams of GDK-6B Incline mine was endangered due to deep-hole blasting at OCP-III. There were 15 water dams in seam 3 and 16 dams in seam 4 of the underground mine. The physical strength tests using a Schmidt Hammer instrument were carried out in all the 15 water dams of No. 3 seam and 16 water dams of No. 4 seam. The test revealed that there is a decrease in compressive strength values of three dams of seam 3, namely 6A, 6B and 7. Theose three dams were also directly connected to the water source. Water seepage was also observed from the surfaces of the three dams. However, they were found to be stable in accordance with their design parameters and damage point of view while considering a threshold value of ground vibration as 25 mm/s. It was found that the value of tensile stress generated by a vibration of 25 mm/s was much lower (i.e. 0.171N/mm2) than the tensile strength of the two weakest concrete dams (1.85 N/mm2). Ten experimental blasts were conducted at different working benches of the opencast mine and the ground vibration data were recorded in roof and pillars near various underground water dams. The maximum value of vibration data recorded was 5.9 mm/s in roof near dam no. 1 in seam 3 with the dominant peak frequency of 22 Hz. No adverse effect on either of the dams was observed after that blast. During the period of study, no deterioration/adverse impact was found in any dam of the mine. Based on the results of the study and the analyses of the data, optimized blast design parameters and explosives weight per delay were suggested for the opencast mine to maintain the safety of the underground water dams. Keywords: Opencast blasting, damage, water dams, underground mine, ground vibration

Jan 1, 2009

By D Craw, G Eis

Late Cretaceous Blue Spur Conglomerate preserved as isolated remnants at Gabriels Gully, Weatherstones, Forsyth, Waitahuna Gully and Adams Flat was deposited during the intiation and early stages of extensional movement on the Tuapeka Fault zone at each locality. The deposits represent successive courses of a single fluvial system flowing across the Tuapeka Fault zone from the up-thrown (northeast) block. Each course, beginning with the channel at Gabriels Gully, was abandoned as a result of uplift-induced defeated antecedence in favour of a new course farther to the southeast around the southeast-propagating tip of the Tuapeka Fault zone. Schist and quartz in the conglomerate was derived ultimately from schistose rocks northeast of the Tuapeka Fault zone. Caples Terrane greywacke detritus in the middle and upper beds of the conglomerate was probably recycled from pre-existing sedimentary cover on the up-thrown block, following initiation of uplift on the Tuapeka Fault zone at each locality. Most of the gold is derived from vein sources in Otago Schist rocks to the north, and/or associated placers. Hydrothermal veins at Waipori, Hindon, Barewood, and Macraes are the most likely primary sources. There is no evidence to support previous interpretations of deposition by river systems flowing from the southwest, or axially along the Tuapeka Fault zone from northwest to southeast. High gold grades within Blue Spur Conglomerate should have a linear trend more or less similar to the orientation of the host channels, but are likely to drop off rapidly to the southwest. Extensions of the conglomerate-filled channels are unlikely to be preserved, but there is a strong probability that younger placers recycled from the former channels exist.

Jan 1, 1999

By Gordon M. Matheson, Douglas A. Anderson, David K. Miller

"Traditionally, analysis of vibrations from blasting has been focused on peak particle velocity fordetermining the likelihood of both annoyance and damage. The US Bureau of Mines, in RI 8507,indicated the importance of frequency in vibration. Methods of controlling the vibration by reducingthe vibration concentrated in certain frequency bands using delays have been successful over the past decade."

Jan 1, 1997

By Åke Krukka, Heribert F. Broicher

"The iron ores of the Kiruna Mine in Sweden are of exceptional quality but for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998 LKAB has been testing prototypes of LIF Analysers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground the mining engineer supports the efforts of the metallurgist in the processing plant.INTRODUCTIONThe Kiruna Mine of LKAB, Sweden is the largest underground iron ore mine in the world. In the early nineties LKAB decided to develop the Kiruna orebody further down from the 775m main level to a new main level at 1045m. This development programme was realised while in the mineral processing section and in the pellet plant further capacity was added (Wyllie 1996).In addition to deepening of the mine, which opened up 330 million tonnes of ore, the exploitation of the so-called lake ore was included in the future planning, adding another 1 15 million tonnes of mineable ore. At an annual production of approximately 20 million tonnes of ore the Kiruna Mine today looks at a developed ore reserve sufficient for the next 20 years.All of the competitors’ ores traded in the world market are from open pit operations. LKAB compensates for the obvious disadvantages by continuous efforts to make the best possible use of her high quality magnetite ore deposit. This objective is realised by combined efforts in the pellet plant, the mineral processing plant and the mine. Propriety processes, latest big scale equipment and high tech solutions for automation lead to high quality sales products at a reasonable cost."

Jan 1, 2002

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for optimization of existing foundations and subsequent re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2011

By Gary Kuhns

Central Florida is among the fastest growing urban areas in the United States, and its rapid development has required the steady construction of various types of civil engineering works. The karst geologic terrain and variable geotechnical conditions, however, present special challenges to the design and construction of deep foundations. The subsurface profile can be idealized as a surficial layer of Pleistocene sands, underlain by the highly variable Miocene-age Hawthorn Group, consisting of various combinations of sand, silt, clay, phosphate and highly weathered limestone. The Hawthorn Group is underlain by Eocene-age limestone that comprises the Floridan aquifer. Vast networks of solution cavities are present throughout the Eocene limestone, sometimes allowing downward raveling of the overlying soils and the creation of sinkholes. In some cases, the relic sinkholes can be filled with soft compressible organic soils extending to depths greater than 100 feet (30.5 m). Driven piles are frequently employed as a deep foundation alternative, although occasionally cast-in-place piles/shafts have also been used. Piles are often driven for bearing in the weathered limestone within the Hawthorn Group, but are sometimes installed as friction piles in the upper soil and intermediate geomaterials. Dynamic pile testing is routinely performed during pre-construction test pile programs, or during production for quality control and assurance purposes. This paper presents discussions on the design and construction aspects of deep foundations unique to Central Florida subsurface conditions and local practice. Foundation issues such as subsurface variability, soil setup, pile damage, negative skin friction, and sinkhole conditions are discussed with the aid of demonstrative case histories.

Jan 1, 2003

By Honeycombe R. W K, Greenwood J. N

Powder metallurgy has been developed rapidly in the last twenty years by overseas metallurgists. The technique of making the powders and their subsequent pressing and sintering into useful forms has' only been introduced into Australia under the stress of war-time economic conditions.The technique involved has very little in common with our usual methods of fabricating engineering alloys by melting the ingredients to a homogeneous mass, followed by casting to shape or casting to ingot form and shaping by application of pressure-so-called mechanical working. On the other hand, the technique includes operations, such as milling and sizing, familiar to the primary metallurgists.The compacting of metal or other powders finds important application in two outstanding fields of engineering production: (a) in making porous bearings and contact brushes, in which such a material as powdered graphite can be incorporated; (b) in making cutting tool tips of hard -carbides, which have a melting point too high to make casting feasible, and which would be too brittle in the cast condition in any case. In both these cases; the final article can be made of the desired shape and size (subject to shrinkage allowances) whilst the compact is in a soft and readily machined condition a consideration of great importance in connection with the hard carbides.In order to develop the necessary equipment and technique and at the same time to assisil in the war effort, it was decided to divert the research work of the Metallurgy Department of the University of Melbourne to the problems associated with the production of hard carbides from local raw materials and the sintering of such into tips for cutting tools. Since this work was started at least two industrial concerns have started to produce these materials in the Commonwealth.The work. to date has included (a) the purification of crude cobalt oxide from Risdon and the reduction of this to metal Particles of less than 10 p. diameter; (b) the production of tungsten powder from King Island scheelite and its conversion into tungsten carbide with particle size less than 4 p. diameter; (c) the sintering of the latter product, using the former as a bond; (d) the production of titanium carbide from titanium dioxide; (e) the separation of columbium and tantalum oxides from a Northern Territory tantalite, and the conversion of these into the respective carbides.

Jan 1, 1942

By C. C. Clark, P. W. Patton, B. M. Stewart

Handling materials in underground mines continues to be a major safety problem. To help reduce materials-handling injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating those materials-handling tasks in underground mines that appear to generate a high number of injuries. Data from the Mine Safety and Health Administration for the years 1989-1999 were studied to find out if there were any trends in materials-handling accidents and if so, to determine what tasks were involved and the sources of injuries. Several underground coal and metal mines were visited to document innovative materials-handling technologies. Considerations for safety training and mechanization needs for continued reduction in materials-handling injuries are described.

Jan 1, 2002

By Andrew L. Peterson

CATOH Inc. of Weedsport, New York recently completed a very challenging Bored-In Pile project which features unique construction techniques in the installation and load testing of 45 and 100 ton capacity piles. The bored-in piles were installed on a twenty-nine million dollar New York State Department of Transportation project which began in the fall of 1995 and ended in March of 1997. The project included the construction of 5 new bridges to alleviate a very congested traffic network which had come to be known as the "Octopus" in the small city of Ithaca, New York. CATOH Inc. was awarded the piling contract by general contractor Santaro Industries in the fall of 1995. Piling installation work was completed in March of 1997. BACKGROUND The project is located at the southern tip of Cayuga Lake which lies in the heart of Upstate New York's Finger Lakes Region. This region is popular not only for wine making and vacationing, but also for its impressive geological history. The glacial activities that helped to form the deep valleys of this scenic area are also responsible for creating challenging underground conditions for deep foundations work. CATOH developed two pile designs to accommodate differing site conditions on the project. Internally reinforced piles were developed for use in the center of the valley and externally reinforced piles were developed for locations close to the valley wall.

Jan 1, 1997

By Raymond J. Castelli

The paper provides a general overview of the numerous types of earth retaining systems currently available, and organizes these various systems by several classification methods. These classifications can be used as a guide in identifying the appropriate type wall or walls for any specific project application. As a further aid in sorting through the numerous wall alternatives for a specific design or construction project application, the paper suggests a systematic approach for wall selection, and presents helpful charts summarizing the general advantages and disadvantages, and typical limitations for the currently available wall systems.

Jan 1, 2003

By K. G. Thorne, L. J. Cabri, L. R. Fyffe, D. R. Lentz, D. Hoy

"Mineralization at the Main zone of the Clarence Stream gold deposit in southwestern New Brunswick occurs within a parallel series of quartz veins that occupy a NE-trending, steeply north-dipping, brittle-ductile shear zone related to the nearby terrane-bounding Sawyer Brook fault. This deformation zone cuts volcaniclastic sedimentary and volcanic rocks of the Silurian Waweig Formation, and is intruded by mantle-derived East Branch Brook gabbroic dikes and a number of felsic dikes. Intermittent shear-zone reactivation during local magmatic activity induced heterogeneous deformation and alteration of the country rocks and dikes. The terminal phase of shearing is associated with narrow pegmatite-aplite dikes that grade laterally into granophyric granite, and into an auriferous quartz vein. Gold, aurostibite, and gold-antimony intergrowths, predominantly with vein quartz, are associated with a low ƒO2 sulfide mineral assemblage (pyrrhotite, arsenopyrite, and berthierite) that has a sulfur isotopic signature consistent with a magmatic source. Gold saturation and deposition occurred episodically between 300° and 360°C at low activity of sulfur, predominantly in response to pressure reduction during brittle failure combined with the effects of decreasing temperature and sulfidation reactions during fluid-wall-rock interaction. Geochronological studies demonstrate that the timing of the emplacement of the pegmatite-aplite dikes and associated auriferous veins overlap with that of the Early Devonian Magaguadavic granite. Moreover, the composition of the dikes is consistent with their derivation from this granite as late fractionates. The Main zone of the Clarence Stream deposit is therefore interpreted to be intrusion-related, with the Magaguadavic granite being the ultimate source of the gold-bearing fluids. La minéralisation de la zone principale du gisement aurifère de Clarence Stream dans le sud-ouest du Nouveau Brunswick occupe une série de veines de quartz parallèles dans une zone de cisaillement fragile-ductile de direction NE et à pendage abrupt vers le nord apparentée à la faille de Sawyer Brook avoisinante qui délimite deux terranes. Cette zone de déformation recoupe les roches volcaniclastiques et volcaniques de la Formation de Waweig d’âge Silurien et est recoupée par les dykes de gabbro d’East Branch Brook, d’origine mantellique, ainsi que par divers dykes felsiques. La réactivation intermittente de la zone de cisaillement durant l’activité magmatique locale a entraîné la déformation et l’altération hétérogènes des dykes et de l’encaissant. La phase finale du cisaillement est associée à de minces dykes d’aplite-pegmatite qui passent latéralement à des granites granophyriques, puis à des veines de quartz aurifères. L’or, l’aurostibite et les intercroissances d’or et d’antimoine principalement associées aux veines de quartz sont associés à un assemblage minéral de sulfures à faible ƒO2 (pyrrhotite, arsénopyrite et berthierite) présentant une signature isotopique du souffre compatible avec une source magmatique. La saturation en or et la précipitation a eu lieu épisodiquement entre 300° et 350°C dans des conditions de faible activité de souffre, principalement en réponse à la baisse de pression durant la rupture fragile ainsi qu’aux effets de la baisse de température et aux réactions de sulfuration durant l’interaction entre le fluide et l’encaissant. Les études géochronologiques indiquent que l’âge de la mise en place des dykes de pegmatite-aplite et des veines aurifères qui leur sont associées coïncide avec le granite de Magaguadavic, d’âge Dévonien Précoce. De plus, la composition des dykes est compatible avec une origine provenant de ce granite sous la forme de phases fractionnées tardives. Le gisement principale (Main zone) de Clarence Stream est ainsi considéré comme étant associé aux intrusions, le granite de Magaguadavic étant la source ultime des fluides aurifères."

Jan 1, 2008

By Frank T. Duda

A U.S. Bureau of Mines interactive FORTRAN computer program can screen explosion-proof enclosures intended for underground service. The program incorporates important information and criteria to assist enclosure manufacturers and Mine Safety and Health Administration (MSHA) personnel by providing a first-order approximation of rectangular explosion-proof enclosure characteristics prior to actual certification testing. The program uses information and data that can be retrieved automatically during program execution. The program also performs the calculations for a series solution algorithm and various equations to evaluate the enclosure for both a static internal pressure and an internal explosion. The program writes the intermediate and final calculations and information concerning the status of the screening process to a summary file on a floppy disk. One data base contains MSHA certification requirements given in the Code of Federal Regulations (30 CFR 18). A second data base contains material properties of acceptable construction materials and weld joint efficiencies. A series algorithm determines bolt and cover stresses for a simply supported rectangular cover with arbitrary bolt locations. Limit and yield line analysis is used to calculate the strength of body panels.

Jan 1, 1989

By J. West

For many years line-of-sight (LOS) issues for underground mobile equipment is a growing focus of research. This research is a result of the numerous fatalities and injuries which occur in the mining industry and which are related to poor operator LOS. Three assessment methods are currently used to assess operator LOS of underground mobile equipment. The light filament (LF) method is a hands-on assessment method that is performed in the field. This method is not evaluated in this paper. The laser scan (LS) method of assessing equipment is a quick and reliable method that comes from the need to evaluate vehicles already located in the field. The computer simulation (CS) method can assess LOS issues using a computer aided drawing (CAD) model, which is useful for assessing current or prototype models. The purpose of the current research is to compare and validate different operator LOS assessment methods. Comparison of the results of the LS and CS visibility plots yielded similar quantifiable results. A visual comparison of the results further illustrate that the LS and CS methods are acceptable assessment tools for mobile equipment operator LOS evaluation. The visibility assessment methods are now being prepared as guidelines for the mining industry to assess current and potential designs.

Jan 1, 2007

Quantitative seismology is an important tool for investigating mineinduced seismicity and the quantification of the seismic rock mass response. The spatio-temporal interpretation of seismic data within an ever-changing three-dimensional mining environment provides some challenges to the interpretation of the rock mass response. A grid-based approach for the interpretation of spatial variation of the rock mass response provides some benefits compared with approaches based on spatial filters. This paper discusses a grid-based interpretation of seismic data. The basic methods employed in the evaluation of the parameter values through space are discussed and examples of applications to different mine sites given.

Jan 1, 2014

By T. Ruben

Micropiles have been used for the last forty years to strengthen building foundations. This article gives information about the technology and capacity of micropiles.

Jan 1, 2000

By K. E. Livo, D. H. Knepper

Modern remote sensing provides a means for locating and characterizing exposed mineralized systems in many parts of the world. These capabilities are non-invasive and help target specific areas for more detailed exploration. An example of how remote sensing technology can be used is evident from a study of the Questa Mining District, New Mexico. Analysis of low spectral resolution data from the Landsat Thematic Mapper satellite system clearly shows the region-al distribution of two broad mineral groups often associated with mineralized systems: clay-carbonate-sulfate and iron oxides-iron hydroxides. Analysis of high spectral resolution data from the Airborne Visible and Infrared Imaging System (AVIRIS) shows the occurrence and distribution of many individual mineral species that characterize the pattern of hydrothermally altered rocks in the district.

Jan 1, 2004

By N. M. Skarbøvig

Safety nets have been used selectively in several South African mines over the years. Recently, however, an increased emphasis on mine safety has seen a resurgence of their utilization underground. This renewed interest has, however, also raised questions about the design and performance of these nets and their practical applications underground; these are the subjects of this paper. Generally, mine safety nets are used to protect personnel from falling rock in temporarily supported development ends, tunnels, ASGs and stopes. These diverse applications each require specific net designs, resulting in a wide product range. As a rule, however, mine safety nets need to carry specified static or dynamic loads with the least possible deformation. Because of the application-specific characteristics of mine safety nets, there is no South African national standard for them. Consequently, neither the SABS, nor the CSIR, performs standard tests on these components. In 2007, therefore, SIMRAC made available their Savuka facility for the testing of mine safety nets; the Savuka drop test became the accepted industry test standard for mine safety nets. From late 2007 to mid 2009, Norsenet, in collaboration with SRK Consulting, the designated operators of the site, conducted approximately 200 tests, which formed the core of Norsenet's database of safety net performance under various loading conditions. The test specimens comprised a wide range of net materials and config¬urations; the materials included: high density polyethylene, polypropylene, polyester, nylon, as well as a blend of polyester and polypropylene used primarily for reinforcement ropes. Net configurations encompassed the following parameters: net type, i.e., knotted nets or sewn nets; net strand type, i.e., braids, twines, or webbing; strand size; mesh size; mesh orientation, i.e., parallel or oblique to the net edge; net edge reinforcement, i.e., knotted, tied, with or without reinforcement ropes; internal reinforcement ropes, i.e., diagonal ropes and/or orthogonal ropes; as well as net attachment options, including loops and chainlinks. From the number of variables listed above, and the limited number of tests available, it can be appreciated that the findings of the test series required careful scrutiny. Nevertheless, principal performance factors clearly emerged: besides the obvious net mesh variables, such as net strand material, strand diameter and mesh size, it was the configuration of the reinforcement ropes and their attachment to the net panel which had the strongest influence on net performance. All the structural elements of a safety net need to work together to transfer the imposed load from the net panel, through the reinforcement ropes, to the net attachment points. In this load transference chain, the weakest link limits the strength of the structure. From this development work, Norsenet has gained valuable expertise to custom-design and manufacture nets to clients' specifications. The examples presented in the paper will also show the experience acquired in the installation of nets underground. Future work will include the establishment of a state-of-the-art net testing facility at Norsenet's factory in Vredenburg.. Keywords Mine safety net, safety net, protective device, mine safety, safety net design, safety net performance, safety net applications.

Jan 1, 2011

By Clara María Lamus Molina

The following minerals found in the residual black sands from gold mining in El Bagre Antioquia (Colombia) were identified as having major economic interest: Ilmenite (FeTiO3), with an average of 49% of TiO2, frequently altered presenting crowns; lamellaes of rutile and alteration textures; titanomagnetite with up to 25% of TiO2; magnetite (Fe3O4) in individual grains or associated with others minerals as hematite and ferromagnesian silicates rutile (TiO2) with considerable quantities of Nb2O5(0.1-3.7%Wt); zircon (ZrSiO4) with 66%Wt of ZrO2 and monazite with an average of 63.43%Wt of REE, this frequently associated to xenotime and thorite forming textures as little drops. Analysis in EPMA and SEM/EDS showed percentages of minor elements and traces, thereby clearly establishing the applications of these minerals in diverse industries. Furthermore, a detailed granumetric study of the different minerals and textural relationships among them also allowed for establishing the basis for possible processing and exploitation.

Jan 1, 2006

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note' describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris's latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By Brian Khalighi, Massimo Franceschi, Giovanni Giacomin, Gianni Porta

Headrace Tunnels and parts of the Access Adit Tunnels of Kárahnjúkar Hydropower project, KAR-14, in Iceland will be excavated using three full-face Robbins Tunnel Boring Machines (TBM). TBM sizes range from 7.23 to 7.63 meters in diameter and the total headrace tunnel length is approximately 40 km. The crushed rock is transported on conveyor belts to disposal areas near each Adit. The estimated average excavation rate is approximately 25 meters per day per machine. Electricity will begin to flow in April 2007, and the project is scheduled for completion in 2009. This paper is divided into four sections. In the PROJECT OVERVIEW section, a short overview of the scope of the project is presented. In the GEOLOGY section, the geological condition along the tunnel drives is briefly introduced. The TBM DESIGN section discusses the various design criteria and the resulting machine specifications. The paper concludes in the TBM OPERATION section with a case history describing the tunneling operation from start-up to the time of the writing of this paper.

Jan 1, 2005