Search Documents

By Mark Lawshe, Shosie Serata

The conventional method of mining underground, using narrow rooms and wide pillars, has proven to be poorly adapted to the powerful earth forces that act on underground openings. The high costs of roof bolting, timbering, steel arching, and other means of artificial roof support for both room-and--pillar operations and longwall gate roadways attest to the limitations of traditional mine design. Too often, productivity halts when corners buckle under "cutter roof' stresses, floors heave, and roof strata fall. In the 1960s, an entirely different approach to strata control was developed. The Stress Control Method (SCM) stabilizes failing roofs and heaving floors by removing the cause of failure - highly concentrated stresses around the openings. This is achieved by regrouping three to 10 rooms into a single entry where the rooms are separated by very narrow yielding but stable pillars. SCM employs a specified excavation sequence to redirect earth pressures away from the mine openings. The yield pillars act as scaffolding until a permanently protective secondary stress envelope forms around the entry (lower part of Fig. 1). The result is a dramatic improvement in roof stability and a significant reduction in artificial support costs. Some roof bolting must still be done, mainly to meet Mine Safety and Health Administration (MSHA) requirements. Potash, salt, coal mining The stress control method was first applied to the deep potash mines of Saskatchewan. The new SCM design actually increased room widths to enlarge the stress envelope, redistributing the stress concentration away from the entries (Serata and Schultz, 1972). This resulted in a turnaround from pervasive roof fall/floor heave conditions that threatened operations in the eight new mines opened in the Saskatchewan potash field during the 1960s. In addition to eliminating all roof bolting, SCM successfully stabilized ground conditions and substantially increased productivity over the original design (Serata, 1976, 1982). Similarly, the deep Boulby potash mine of Yorkshire, England, was about to close after various conventional means of combating roof failure had failed. An SCM test area was excavated that resulted in the ground quickly stabilizing without need o artificial support (Serata, 1982; Chilton and Laird, 1982). Another example is the Diamond Crystal salt mine in Louisiana. Here, multiple level mining was being extended from the third to the fourth level downward in the Jefferson Island salt dome. Extensive roof failure was occurring at 396 m (1300 ft) ii the third level. SCM design principles in creased the room size from 24 to 49 m (80 t( 160 ft) on the fourth level at a depth of 457 m (1500 ft). This unprecedented expansion of room width was first questioned and later ap¬proved by MS HA, which expressed satisfaction in seeing the improvement documented by field validation data in 1973. The most recent SUM application to salt mining has been in the Michigan Basin a: Goderich, Ontario. The anticipated abandonment of Domtar Chemicals Group/Sifto Salt Division's deep operation in bedded sale was prevented by a multi-year SCM implementation. The success of SCM in dry mining[lecc] to its application to solution mining of salt This adaptation of the method is now being implemented in bedded salt at Fort Saskatchewan, Alberta by Dow Chemical Co., and in St. Clair, MI by International Salt Co. Application of SCM to solution mining in a salt dome is proceeding at Napoleonville. LA by Dow Chemical. The same technology has also been applied to cavern design for the Louisiana Offshore Oil Port (LOOP), and the compressed air energy storage (CAES)

Jan 1, 1989

By C. Travis Anderson

"Nickel is an essential metal in stainless steel, armor plate, and nickel steels and also in nonferrous alleys, such as monel metal and cupre-nickel, which are used in marine service. Nickel is one of the metals that must be greatly restricted in civilian use to provide the amounts needed for our War program. Consequently, it is desirable to investigate every possible substitute.The 5-cent coin no z in use contains 2.3 percent nickel. At the end of 1941, about 450 tons of nickel was being consumed annually to produce these coins. If the nickel used for that purpose in 9141 had been diverted to military use, 15,000 tons of armor plate could have been produced. As nickel is vitally needed for military as well as essential civilian products, it would seem desirable to substitute some other alloy for the 25 percent nickel alloy now being used. The Bureau of Mines has been asked to suggest possible substitutes.The substitute should have physical properties similar to the alloy now being used. It should have a metallic appearance and ring and a reasonably white color, so to be distinguishable from the present 1-cent coin. It should also be reasonably resistant to corrosion."

Aug 1, 1942

By O. C. Garst

"The lightness and relatively high strength per unit weight of certain magnesium alloys have interested designing engineers for many years. Ever since the noted investigator Bunsen3/ first produced the element by electrolysis of the fused chloride in 1852, utilization of this light metal has been considered. Magnesium is widely distributed over the earth's surface in high-grade as well as low-grade deposits; it occupies eighth place in the list of elements arranged in order of their decreasing abundance, as there is 2.24 percent magnesium in the earth's lithosphere. Even though the element is distributed widely in the form of relatively insoluble: minerals and also as soluble salts in sea water and spring water, as well as being an indispensable constituent of plants and animals, the technology of magnesium was slow development. This slowness of development was first caused by confusion or the part of the early investigators who thought that magnesia, magnesite, magnetite, and the pyrolusite-type manganese ores were compounds of the same metal. At one time the metal that we now know as manganese was called magnesium, and magnesium was called either magnium or talcium. In addition to this coon, the chemical activity of the metal, especially at high temperatures, created problems that are still difficult to solve.With the advance of science in all branches, .methods for -he production of magnesium were developed. The methods first used for producing the element were: (1) reduction of magnesium salts with alkali metals,4/ (2) electrolysis of aqueous solutions of magnesium salts, and (3) electrolysis of fused magnesiun salts.The first attempts to produce magnesium by the carbothermal reduction of magnesia were failures as sufficient thermodynamic knowledge concerning the reversibility of the reaction between magnesia and carbon was not at hand. As the igneous electrolytic Method for making the element was more easily controlled than the others and. yielded more metal per unit of energy, considerable work was expended on the improvement of this process. The work in this field paralled that on the electroreduction of aluminum and the alkali metals. For several years the entire magnesium industry was dependent on this igneous electrolysis process for its supply of the metal, but as demand for the metal increased and more scientific knowledge was available, other processes were developed. Today magnesium is produced by the electrolysis of molton magnesium chloride electrolytes, the carbothermal reduction of magnesia, in arc furnaces followed by shock cooling of the furnace gases by a coin inert atmosphere, and the silicothermal reduction of calcined dolomite in stainless steel retorts."

Mar 1, 1946

Jan 1, 1882

LOCAL COMMITTEE OF ARRANGEMENTS. Major J. W. Powell, Chairman; F. P. Dewey. Secretary; S. F. Emmons, A. S. Hewitt, J. P- Hilgard, Charles Knap, and F. W. Taylor. THE opening session was held in the hall of the new National Museum, on Tuesday evening, February 21st. President Metcalf introduced General W. T. Sherman, one of the Regents of the Smithsonian Institution, who read the following address: ADDRESS OF GENERAL SHERMAN. MR. PRESIDENT AND GENTLEMEN : I have been invited to meet you here this evening to extend to you the cordial greeting of the regents of the Smithsonian Institution, and to assure you that they are most happy to have it in their power to place at your disposal this beautiful hall, dedicated to science and art. This National Museum is the property of the United States, of which the regents of the Smithsonian are simply the custodians, and the board has delegated to its secretary, Professor Baird, the right to extend its use to the National Academy of Sciences and like kindred societies, among which we are glad to class the Institute of Mining Engineers. It is eminently fit that you should meet here at this, the nation's capital, under a roof partly your own, devoted to natural sciences, and in the shadow of the Smithsonian, founded for the exclusive purpose of collecting and diffusing knowledge among men. Of all the workers employed on earth no single class seem to me more worthy the respect of their fellows than those who seek beneath the surface for the useful minerals and metals which contribute so largely to the wealth and comfort of mankind. In no branch of human industry does intelligence come so immediately in contact with labor. To the mining engineer chemistry, mineralogy, and geology are as reading, writing, and arithmetic to the merchant;

Jan 1, 1882

By B. van Beek, J. Ndlovu, K. T. Hara, J. M. A. Geldenhuis

This paper describes the development of an alternative technique for measuring the matte level height in sulphide smelting furnaces. The initial studies involved applying electrochemical oxygen probes in a smelting furnace to measure the oxygen potentials of the matte and slag phases. However, these measurements were not successful as a result of low temperatures, preventing there ference electrode from attaining equilibrium during the measurements. These trials were followed up by using oxygen probes containing a (Mo + MoO2) reference electrode instead of the(Cr + Cr2O3) reference electrode used previously. It was shown that with some further development work, it should be possible to measure the oxygen potential of these mattes accurately. Further measurements were performed with a magnetic sensor in sulphide mattes. It was shown that an electronic signal, which is proportional to the magnetic susceptibility of the surrounding material, was generated during immersion into liquid matte. These measurements were extended and done in a smelting furnace. Initial results indicated that when the magnetic sensor was dipped through the slag layer into the matte, a signal was generated as soon as the sensor came in contact with the matte. Measurements are ongoing in order to record (on a computer for improved accuracy) the signal as a function of distance when the sensor is immersed through the slag layer into the matte phase. The magnetic sensor measurements may be the solution to a matte level measurement problem that has existed for a few decades in matte smelting furnaces.

Jan 1, 2004

The Canadian concept for nuclear fuel waste disposal is being assessed by AECL Research in a series of experiments at its Underground Research Laboratory (URL) near Lac du Bonnet. Manitoba, Canada. As pan of this research, the Mine-by Experiment has been designed to obtain information on rock mass behavior, the development of an excavation-induced damage zone and failure mechanisms around a circular bored tunnel. An iterative design approach was used to effectively reconcile the experiment objectives and construction logistics. This paper discusses the design considerations and construction methodology adopted on the project.

Jan 1, 1991

By E. C. Yeager, E. O. Wagner, A. W. Koth, V. F. Parry, J. B. Goodman, D. G. Gernes, W. L. Patty

"In July 1943, the Bureau of Nines received an appropriation to investigate the beneficiation of Minnesota iron ores through the use of lignite. The broad objective was to find a way to link the large deposits of lignite in North Dakota with the low-grade iron ores of Minnesota. It was proposed that sponge iron might be made through new methods of processing, and one of the objectives was to determine the possibilities of gaseous reduction of fine ore. The problem of obtaining high-hydrogen reducing gases from lignite was assigned to the Subbituminous Coal and Lignite Section of the Bureau of Mines in August 1943.Through the advice of technical consultants and men familiar with the mineral resources of Minnesota and North Dakota, a tentative program of development was outlined. The first proposal was to study the gasification of lignite briquets in a standard water-gas machine. Previous experience with gasification of lignite indicated that the raw fuel would not be suitable for use in the conventional water-gas process on account of degradation, but gasification of lignite briquets appeared possible. Through the cooperation of the Northern State Power Co„ a series of tests was made at the company's plant in Grand Forks, N. Dak., on lignite-char briquets made by the Lehigh Briquetting Co. at Dickinson, Dak. These briquets are made by the Lurgi process, and they have been used satisfactorily as a domestic fuel. The object of the tests was to compare gasification properties of lignite-char briquets with those of gas. coke made from Kentucky coal, normally used in the Grand Forks plant. The tests revealed that the lignite-char briquets were not suitable for gasification, in the standard water-gas process because of disinte-gration and low efficiency caused by loss of fine carbon.While these investigations were underway, a joint Minnesota-North Dakota Development Commission was formed to aid in planning investigations on development of mineral resources of the two States. Some members of this commission were technical men, who with consulting engineers on the Bureau's staff made up an unofficial technical committee, and assisted in solving certain problems connected with gasification of lignite and beneficiation of iron ores. This committee has been of 'real assistance in guiding the investigation.A technical meeting was held in Minneapolis on November 10 and 11, 1943, for further discussion of objectives and certain technical problems. Results of tests on lignite briquets were presented, and several reports analyzing other methods of gasification were discussed. The Reyerson-Gernes process for the continuous gasification of lignite in an externally heated retort was considered from several angles. This process differs from others in that the natural moisture in the coal is utilized to help gasify the coal, and the volatile matter is largely decomposed. Although this process had been carried out successfully in a small steel retort, no definite design for a commercial-scale retort had .been developed. It was first proposed that the process might be carried out in a Glover-West retort. However, it was brought out that a Glover-West retort would require modification to simulate the process correctly, and that good results might not be obtained even then owing to the leakage of gas through the refractory walls and to an anticipated low rate of heat transfer at the gasification temperature suitable for lignite. Further, the probable leakage of inert furnace gas into the water-gas would be adverse to the Objective to obtain a gas that could be purified to 96 percent hydrogen."

Jun 1, 1946

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

"A bed, British Columbia, Canada, coal, carbonizingproperties B 510Pa., coal, washing characteristics RI 4941A' bed, Pa., coal, washing characteristics RI 4834"

Jan 1, 1960

By Joseph L. Jordan

Coal is essential to America?s future energy needs. To meet these needs mining methods must be safe, economical, and environmentally acceptable. Belt conveyor systems for coal haulage from surface mines offer great potential in this situation. The advantages over conventional truck haulage are particularly promising for area strip mines in western coal fields such as the Powder River Basin where relatively thick, flat-lying coal seams occur. The current demand for low-sulfur coal specifically emphasizes the need for better mining methods in these areas. Underspoil haulage is the term applied to transportation of coal from the pit to the surfate in area strip coal mines by belt conveyors in tunnels under the spoil. The advantages over trucks include lower manpower requirements, greater pit safety and efficiency, and improved reclamation procedure. This evaluation includes a comparison of total mining costs for truck haulage versus six variations of the underspoil haulage concept. The more efficient of these underspoil haulage systems have economic advantages over truck haulage which become more pronounced with deeper overburden, thicker coal, and higher annual production.

Jan 1, 1977

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

By Albert L. Toenges

[The i~ ortance o~ S3~e, fdequnt, nQ economical tr~n~po~t~t on 8ys~em Th~a bee~ e~~~~siz8d by the introduction of mechanical loading in co 1 mines, pa.rticula:c y \'r~ e::-e ~o?oile loaciine; ~ac~ine!;j rrre u .... ed. This papar i tr_e . eco:1d or' ?. ~eries deGcribi 1{) t:;'~~11>ort:ltion G stems et1-p oyed in mech3JlizeG. f!lincs. Progre,-s ?. epo~ t J...2.t deal t ~~tirel.: ,'Ii th the l:se of rail .laulagr £or c;atl:erine tran~ortc;tion, ailc, in t-!is paper 'Ii 11 be i acuss d c .icilY rub"col'-t? ro ~ t:tto::"ing as Ie _ as ani:naJ., con-",reyor, an ot.he~ systems of rnil gatheri?1.g. ~ho l)urpo~e of this invosti-gation is, as outlined in Progress ,~ort 1, to studT . Q analyz0 v rious systems nov.: in. u"'e El.I1d to derivQ cor..cl :cicn .... tllcrcfrom.]

Jan 1, 1941

A unity of viewpoint emerged from the workshop. The concept that transmission is via characteristic modes was a common theme in many of the presentations. Also, the confusion an the meaning of monofilar and bifilar to describe these dominant modes was cleared up. But, there was still a healthy divergence of opinion on what constitutes an optimum system. It was generally agreed that further analytical and experimental work is definitely needed. In particular, it was stressed that independent measurements of the constitutive properties of the electromagnetic environment are needed. Also, there was considerable concern that laboratory measurements of rock samples could lead to misleading results for the effective conductivities. Also, there was a general recognition that over simplified propagation theory should not be used to interpret field data. From a theoratical and practical point of view, it was realized that mode coupling plays a vital role in the transmission channel. One must not only understand which and how many propagation modes are excited by the transmitting antenna, but the conversion of energy from one mode type to another must be accounted for. This conversion can either be done intentionally (by fixed mode convertors) or non intentionally (by random wall roughness). In fact, mode conversion can be quite complicated when various propagation paths exist such as when insulated cables, leaky feeders, grounded rails, coal seams, etc. all convey portions of the electromagnetic energy. However, this state of affairs should be regared as an. opportunity for extended communication coverage in mines rather than a limitation of a desig. procedure based on preconceived notions of the dominant propagation mechanism.

Jan 1, 1978

By G. S. Scott

Safety problems in the mining and allied industries have led the Bureau of Mines to investigate over a period of years; the flammability (explosibility) of many types of combustible atmospheres principally at ordinary pressure; the results of these investigations have been made available as a bulletin. However, more recently, the demand for information on the flammability of gaseous mixtures at high and low pressures has increased greatly. In particular, the rapid development of high-altitude aviation has brought demands for information on the flammable (or explosive) characteristics of certain gases and liquids at low pressures. The present report gives the results of about 900 tests made to determine the flammability of the lighter paraffin hydrocarbons mixed with air and nitrogen at pressures of 400 200, 100 and 70 ram. Hg. The gases tested include natural gas, methane, ethane, propane normal butane and isobutane. The minimum pressures at which these gases are capable of propagating flame whorl individually mixed with air also were investigated.

Jan 1, 1952

By George F. Kunz

Jan 1, 1902

By R. T. Jones

"SynopsisScientific progress relies on the publication of ideas and experimental results that can be replicated, tested, and improved over time. The first printed book on metallurgy to have been published in Europe is considered to be De la Pirotechnia, written in Italian by Vannoccio Biringuccio, and published in Venice in 1540. Together with De Re Metallica, written by Georgius Agricola and published in Latin in 1556, this can be considered to mark the start of scientific and technical literature in this field. Scientific publishing of journal papers has been in existence for 350 years, since the world's oldest and longest-running scientific journal, the Philosophical Transactions of the Royal Society, was first published in London in 1665.The nature of scientific societies has changed significantly since the early days when regular meetings were held to discuss science and conduct experiments, and the reading of scientific papers took place, and publication of papers was undertaken to record the proceedings of meetings, often including rather robust debate. In today’s world, there is a plethora of publications, and it is close to impossible for anyone to keep up with the vast flow of information. International conferences with hundreds of presentations have taken the place of the local meetings that used to discuss a single paper or experiment. In this frenetic environment, it is essential that researchers are able to trust the material they read.The system of peer review is used to maintain standards and to improve the quality of papers. This vital system is, however, significantly flawed. There is little incentive for reviewers to invest sufficient time in picking up all errors in publications, and any ineptitude on their part is usually protected by anonymity. It has reached the point where some reviewers have mistakenly permitted the publication of hoax papers deliberately presented with a complicated scientific facade. In light of such astounding inadequacies, perhaps a more open review process would be an improvement. Electronic publishing allows errata to be linked to the original papers.There is an increasing trend towards open access for papers in scientific journals and conference proceedings, which helps to reach as wide an audience as possible. This also supports the statement in the Universal Declaration of Human Rights, which says ‘everyone has the right freely to … share in scientific advancement and its benefits’."

Jan 1, 2015

Research 84 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, DC 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1984

By Joel A. Hunt

The Bunker Hill Mine, located in north Idaho, consists of over 150 miles of passageways within highly fractured and faulted Precambrian metamorphosed rocks. The Bunker Hill Mine was at one time a major producer of lead and zinc; currently it is on inactive but maintained status. Ground water moving along flow paths that have been disturbed by mining reacts with pyrite and oxygen to produce acid water within the mine. Discharge of this acid water averages more than 5 cubic feet per second, with an average zinc concentration of 160 mg/L and pH of 2.8. Treatment of this acid mine drainage is required by the National Pollutant Discharge Elimination System (NPDES). Cessation of all underground activities at the Bunker Hill Mine will not terminate the production of acid mine drainage. Reclamation alternatives that could either reduce the quantity or Improve the quality of the drainage upon mine closure are highly attractive. This project is directed towards delineation of reclamation alternatives based upon an understanding of the characteristics of ground water recharge near the mine. A variety of field techniques were used to identify areas of rapid infiltration and to investigate the ground water flow system associated with the upper portion of the mine in a portion of the Milo Creek drainage. These techniques include Installation of piezometer nests, dye tracing, surface resistivity, dye dilution, spring surveys, and hydrochemical analyses. Sites of direct Infiltration into the mine have been located. These include mine workings directly below perennial streams, intersections between streams and faults, and a caved area adjacent to an ephemeral stream. Results of these investigations indicate that recharge through these sites is not as rapid as suggested by previous studies. Inflow to the underground workings from the ground water flow system around the margin of the mine may account for more mine water than sites of direct infiltration. Recharge control at areas of direct infiltration could result in a net decrease in the quantity of acid drainage from the Bunker Hill Mine. Locations suggested for recharge control are West Milo Creek above the Guy Caving Area, the intersections of the Cate Fault with South Milo and Milo Creeks, and an area of Milo Creek below the Milo Creek Dam that overlies shallow mine workings.

Jan 1, 1984

By AIME AIME

SCRIPTURE, statistics and imagination all were drawn upon by the speakers who acclaimed Daniel C. Jackling as recipient of the William Lawrence Saunders Gold Medal for 1930. The award was made at a special dinner at the Ritz-Carlton, in New York, on Oct. 31. Lafayette Hanchett, old friend and associate, said that if it were his task to compress the life story of Daniel Jackling into a single sentence, he could find noth¬ing so appropriate as these words from the 22nd Chapter of Proverbs, "See'st thou a man diligent in his business, he shall stand before Kings." Mr. Jackling's diligence, according to the speaker, his love for his task, have been outstanding in his career. W. S. Boyd, now ranking official in the Jackling organization, cited amazing statistics as to the quantity of copper supplied to industry by the four "porphyry". coppers that are under Mr. Jackling's immediate direc¬tion, as well as by those that, in a sense, owe their existence to the pioneer work at Utah Copper. In the aggregate- 16,000,000,000 lb. of copper having an approximate value of $2,700,000,000 have been produced from disseminated ores since 1905; and of this total 42 per cent came from Utah and the Nevada group. Newcomb Carlton, president of the Western Union Telegraph Co., long an admirer of Mr. Jackling, adroitly drew a picture of a similar occasion in some 'foreign country. He imagined Mr. Jackling being raised to the peerage and whimsically addressed him as Sir Daniel, the Right Honorable Earl of Bingham!

Jan 1, 1930