Search Documents

By Khoo Khyou Pin, Yoshiyuki Funaki, Hirotsugu Takeuchi, Ryoichi Urao, Naotatsu Asahi

"Steel is used to be ion carburized with mixing gas of methane and hydrogen. In carburizing, carbon in the methane decomposes and deposits on the steel by plasma, so methane gas flow may influence on ion carburizing of the steel. An apparatus in which works can transfer preheating, ion-carburizing and diffusion treating zones continuously was made for effective carburizing of steel. The gases were flown into above three zones with three different gas inlets. The hardness and microstructure of the works were investigated after ion carburizing and quenching. The steel is carburized deeper near the carburizing gas flow nozzle of the inlet than far from the nozzle. Hard surface layer fom1ed by quenching of ion-carburized steel.IntroductionGas carburizing is used for a surface hardening treatment which decreases fatigue and wear of the industrial parts used in automobile, machines etc. Ion and vacuum carburizing have been developed recently and applied to some industrial parts of restrictive purposes. The ion carburizing treatment which uses hollow cathode discharge (HCD ion-carburizing) is superior in energy saving, resource saving, environmental cleanness to the other carburizing treatment. Specially, carburizing energy can be saved in HCD ion-carburizing, because highly heated zone can be restricted in the range between work and subsidiary cathode where hollow cathode discharge arises, and the work is carburized in shorter tin1e in HCD ion carburizing method than other carburizing methods. Three treatments of preheating, carburizing methods and carbon potential controlling by hollow cathode discharge tried to be carried out in one continuous transferring series to carburize works more effectively, so the HCD ion-carburizing apparatus with continuous transferring system was made and gears of works were HCD ion-carburized in continuous transferring. The works were rotated themselves to get homogeneous carburizing by continuous transferring in glow of hollow cathode discharge."

Jan 1, 2000

By M. A. Rabah, F. E. Farghaly, M. A. Motaleb

"Wastewater from industrial galvanization industry was reclaimed under current flow stream conditions. Results showed that the raw water contains 0.7 % by weight total suspended solids (TSS) causing turbidity amounting to 30. Measurements of Zeta potential as a function of pH revealed that solid separation takes place at pH 9. Addition of H2O2 to the polmer solution helps to oxdize ions of iron and zinc metals toinsoluble ferric oxide and zinc hydroxide to a higher state of oxidation. Addition of 5 mg/L of cationic magna flocculants polymeric solution helps the rapid separation of the turbidity. Separation of floccules so formed takes place by filtration. Addition of peroxide ions to the turbid wastewater confirms the physical stability of the flocs so formed. Impurity flocculation takes place in few seconds. Maximum temperature for safe solid removal was <30°C. The treated water was pure and safe for recycling or use in domestic purposes.IntroductionStocks and et. al. [1] show that the galvanizing process introduces spent pickling acid waste production, but its major constituent, could be used. Survey of the operational procedures adopted and the acid wastes produced by UK Galvanizers are reported. Various methods to recovery spent acid of suitable composition and to eliminate zinc contamination was considered. Application of the Kleingarn acid management system reduces waste volume, saves hydrochloric acid (HCl) and increases component throughput whilst, in conjunction with zinc elimination, could allow recycling of the majority of galvanizer’s acid wastes.Dahab [2]; Kerney [3] reported recycling of galvanizing products, including pickleliquor. Kerney suggested a mobile treatment plant for recycling pickling acids. Dahab found that pollution reduction could be achieved by relatively simple operational changes to the process that gave fairly short payback times.Rozenblat and et. al.[4] studied the extraction of zinc (II), iron(III) and iron(II) with Tributyl phosphate (TBP) from hydrochloric acid solutions containing high zinc(II) concentration. Two technological approaches for the separation are considered. Firstly, the selective extraction of iron(III) (iron(II) is oxidized to iron(III)) over zinc(II) with TBP deficiency. Secondly, iron(III) reduction to iron(II) followed by zinc(II) selective extraction with an excess of TBP. Prior stripping, the organic phase was washed with small amounts of water. Scrubbing of TBP solutions containing iron(III) contaminated with zinc(II) gives always a mixture of zinc(II) and iron(III) which must be recycled to the extraction step in continuous process. The following technological concept is proposed: reduction of iron(III) to iron(II), extraction of zinc(II) with 5-10 volume excess of TBP, washing of TBP phase contaminated with iron(II) with small volumes of water and recycling of the scrubbings and stripping of zinc with water."

Jan 1, 2008

By XUEWEN WANG, Xingming Wang, Xuehui Liu, Mingyu Wang

The Panzhihua titanium concentrate contains high contents impurity of Mg and Al, and it is difficult to prepare high grade titanium slag. To solve this problem, a sodium salt roasting-acid leaching process was proposed for removing the impurities in titanium concentrate. Na2CO3 and titanium concentrate were mixed with the proportion of 1:4, and then the mixture was roasted at 700 for 2h. After roasting, the calcine was leached with HCl solution. The experimental results showed that the removal rate of silicon and aluminum can reach more than 85% and 80%, respectively, at leaching temperature of 70 , leaching time of 4h, HCl addition of 5ml and liquid-solid ratio of 4:1.

Jan 1, 2016

By Thenepalli Thriveni, Ch. Ramakrishna, Yujin Jegal, Ji Whan Ahn, Jyothi Rajesh Kumar

In alumina production or alumina refining, bauxite is converted to alumina (aluminium oxide) The rare-earth elements (REEs) are a group of 17 chemically similar metallic elements (15 lanthanides, including scandium and yttrium). Rare earth elements play a key role in many industrial applications, petroleum refining, clean energy, automobile, electronics, and defense applications. These rare earths are essential to the success of green technologies. China today controls more than 95 percent of the rare-earth supplies and nearly all rare-earth refining and after 2009 year rare earths crisis raises due to China’s export restrictions and growing internal demand for rare earth elements. The extraction of gallium and yttrium from Korean red mud (KC red mud) by selective acid leaching was explored. The recovery of gallium and yttrium from a leach solution of the Korean red mud using solvent extraction was studied. A number of extractants were investigated for the extraction of those mentioned two rare earth elements and also we proposed a flow sheet of rare earth elements respectively. The toxic heavy metals presented in KC red mud were removed by CO2 stabilization.

Jan 1, 2015

By Igor Zh. Bunim, Valentine A. Chanturiya, Alexey T. Kovalev, Irina A. Khabarova, Elizaveta V. Koporulina

This paper presents new theoretical and experimental data on possible mechanisms for the formation of micro- and nanophases on the surface of sulfide minerals un der the effect of high-power nanosecond electromagnetic pulses (HPEMP). The gas outflow from nanosecond breakdown channels of sulfide minerals under the effect of HPEMP is considered, with allowance for the condensation of iron vapors. The condensation of matter in an outflowing jet is shown to be an effective mechanism for structureal and chemical transformations of sulfide surfaces. It is established that electrode potential of pyrrhotite is moved together in the negative party owing to formation of iron oxides (hydroxides) and iron sulfates by HPEMP, that provides decrease of xanthate sorption and reduction flotation extraction of this sulfide, whereas electrode potential of pentlandite gets more positive values at the expense of additional formation of element sulfur, that causes increase of xanthate sorption and, as a consequence, increase of nickel sulfide extraction.

Jan 1, 2012

By Michael S. Moats, Jan D. Miller, Wlodzimierz W. Zmierczak

"For many, hydrogen in a pure hydrogen economy would be like natural gas in today’s energy economy. Unfortunately, hydrogen’s physical properties are unsuited to the energy market’s requirements in terms of packaging, storage, transfer, and delivery. In this paper, a hybrid energy economy that packages hydrogen chemically on carbon atoms from various sources including recycled carbon dioxide is introduced and discussed. For this new hybrid energy economy to become a sustainable reality, the ability to recycle carbon dioxide and use hydrogen to create an appropriate energy product, such as dimethyl ether (DME), is needed. DME is recognized as a potential next generation, “beyond-petroleum”, environmentally benign commodity for energy storage and distribution. It is expected that to maximize the sustainability of the proposed hybrid energy economy, “green” hydrogen will be utilized. The “green” hydrogen would be created by the electrolysis of water powered by renewable energy sources, such as solar, wind or geothermal heat.IntroductionWith the growing concerns surrounding trends in global warming and increasing concentrations of “greenhouse” gases, such as CO2 and CH4, efforts to mitigate the emission of these gases from industrial sources are growing. With respect to CO2, the demonstrations of various capture and sequestration methods are underway around the world.The sequestration of CO2 is mainly focused on storing the gas underground or deep in the ocean. The Intergovernmental Panel on Climate Change (IPCC) estimates that 2000 Gtonnes of CO2 can be stored underground in depleted oilfields, un-minable coal beds and other geologic features [1]. Additionally CO2 may be stored at the bottom of the ocean. The lure of storing carbon dioxide in depleted oilfields or un-mineable coal seams is that an economic benefit (enhanced oil or methane recovery) can offset the costs of gas capture, transportation and storage. Unfortunately, all of these storage methods have potential for the release of CO2 or CH4 back into atmosphere or creating environmental damage (mobilizing heavy metals, disrupting deep sea ecology)."

Jan 1, 2008

By Kim Fagerlund

A novel apparatus for studying refractory infiltration and dissolution/degradation under a temperature gradient was developed. To supersede conventional isothermal refractory testing, a new temperature gradient technique, based on a crucible equipped with a cooling element, has been developed to provide practical information on the penetration and dissolution of refractory materials under cooled conditions. This technique was adopted and applied to several refractory-slag systems. Commercially available magnesia chrome refractory bricks against a copper-containing calcium ferrite type of slag were tested and compared using both a conventional crucible test and the new temperature gradient method. The experiments were conducted at 1300-1420°C under a controlled atmosphere of nitrogen or air. It was noticed that the type of porosity has a significant effect on infiltration of magnesia chrome refractories. Furthemore, the copper-containing calcium ferrite slag caused a severe slag attack and refractory failure in some cases, due to its fluidity and corrosive nature.

Jan 1, 2002

By Wenjie Zhu

Hexavalent chromium is a widespread environmental contaminant. An Achromobacter sp. strain nominated Ch1 can reduce soluble and toxic chromate to insoluble and non toxic Cr(III) in aerobic cultures, and no Cr(VI) decrease was observed in anaerobic cultures. In contrast with other Cr(VI) reducing microorganisms, Ch1 showed higher Cr(VI) reduction at high pH. Reduction performed under alkaline conditions at pH 7 to 11, and the optimal pH was 10. During the reduction, pH decrease was observed may caused by production of acidic metabolic byproducts from aerobic respiration. In the present study, the ability of Achromobacter sp. Ch1 to reduce Cr(VI) during growth was evaluated with lactate as an electron donor. In NB medium, Ch1 reduced 100% of 24mM of Cr(VI) in 35h, but only 73% of 30mM of Cr(VI) after 48h of inoculation. Reduction was inhibited by metal ions like Ag+, Cu2+, Zn2+, slightly inhibited by Mn2+, and not affected by Mg2+. Results revealed that reduction rate of Cr(VI) also increased with the increasing of concentrations of lactate, and complete reduction was achieved at the concentrations above 40 mM. HPLC analysis demonstrated Cr(VI) reduction was associated with the consumption of lactate. There was a large quantity of dark blue sediment generated in the culture during Cr(VI) reduction by Ch1. Energy dispersive X-ray (EDX) analysis showed that the major element composed the formed sediment was chromium presented as Cr(OH)3 precipitate. The features characterizing Cr(VI) reduction by Achromobacter sp. Ch1 are high Cr(VI) concentrations and high pH.

Jan 1, 2006

By A. F. Usov

"The use of the Electric Pulse Discharge method of materials destruction (EP) for disintegration of materials in an industrial-waste processing are examined. The principles and Experience of the development device of EP-disintegration have been described, the technological efficiency of disintegration of industrial minerals estimated.IntroductionThe Russian scientists have proposed and comprehensively studied the electric pulse (EP) technique which is applied in ores and materials disintegration [1, 2 ]. The different aspects of the problem have been presented by the authors in papers at many international congresses [3-6]. Recently the technique is intensively developed in many countries, and various disintegration installations are exhibited.Crashing and disintegration of ores by EP-method is characterized by high selectiveness of destruction. It provides better disclosure of mineral grains and prevent it from destruction. EPmethod reduces slurry formation. All this provides better mineral extraction at ore beneficiation and improves concentrate quality. It also prevents the product from polluting with equipment metal, inwall and grinding equipment material. The possibility to change the character of dynamic loading allows controlling grain-size composition and getting small-size product in contrast to mechanical method of crashing.The product of EP-crashing is characterized by less toughness and greater specific surface area of grains since the new surface is formed at splitting and chinks extension. The product is of high sorption and reactivity in chemical changes. Open grains of mineral spots correspond to their natural condition and it is of great importance for studying mineral.The principles of the development deviceLong-term studies of the technique carried out by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute ""Mekhanobr"" (S.Pertersburg), made it possible to substantiate principles of the disintegration installations design, make exploratory stands and technological installations to carry out pilot tests and operations under production conditions. The construction design of disintegrating installations depends on many technological and physical factors. Of all the technological factors, the most significant one is to preserve the liberated product because it is the peculiarity of the EPdisintegration to have high selectivity of disintegration. The preservation of the mono-mineral product liberated from the rock mass means that this product is not overgrinding, which causes the loss of the product with slime in processing, and that the initial natural form of the mineral inclusion is also preserved because it is the size and the integrity of crystals that determines its cost value (precious minerals). On the one hand, it is provided by a stage disintegration technique, with the product classified after each stage, and, on the other hand, by selection of specific conditions of electric breakdown, which ensure high performance of electric breakdown and effective disintegration of material fragments, with the useful mineral inclusions preserved intact, with its size considerably exceeding the discharge gap. These conditions are provided by the appropriate geometry of electrodes, the discharge gap and the screen size due to the material’s nature and grain size."

Jan 1, 2008

By T. Taniguchi

The existing Mitsubishi Process line at Naoshima Smelter and Refinery has been operating successfully since 1991, and its present production capacity is 270,000tpy of copper. Furnace relining works have been carried out every two years to coincide with the compulsory bi-yearly boiler inspection, but the next target is to extend the furnace refractory life to four years, while still undergoing the mandatory boiler inspection every two years. Although the damage of hearth bricks beneath lances in the Smelting furnace was a matter of concern, it was reduced by controlling gas velocity and evening solid distribution to each lance. The life of bath level bricks in the Converting furnace was also a concern, but four-years continuous use of the bricks was achieved in the course of the last two campaigns. Several other improvements were also carried out to the cooling systems during the shutdown in 2005 to ensure longer campaign life. This paper summarizes recent improvements implemented to enhance the advantages of the Mitsubishi Process.

Jan 1, 2006

By L. Dornelles, M. H. Prediger, R. de C. de S. Schneider, D. A. R. Lopez

In this work it was evaluated the environmental impact of sunflower plantation for biodiesel production. It was considered, for life cycle analysis (LCA) of sunflower in familiar agriculture in the South of Brazil, data collected in 23 experimental farmings with sowing in the period from August to November (2006 -2007). The LCA has considered the plantation conditions, energetic efficiency, man power, diesel volume, type of machines, fertilizers and pesticides used. From the analysis carried through it was evidenced that the sunflower produced in small scale does not need the use of tractors to have an excellent productivity and low impact. Therefore, the sunflower can be cultivated, with the necessary cares, in periods that do not compromise the man power for other cultures and the sunflower is an alternative so that the familiar property can produce biodiesel.

Jan 1, 2008

By Frédéric Pineau, Guillaume D'Amours

Semisolid metal processing of metallic alloys takes advantage of the thixotropic behavior of material with non-dendritic microstructure to produce near-net-shape components with improved mechanical properties. The much higher apparent viscosity of the semisolid billet limits the risk of oxide formed on the free surfaces to become incorporated into the easting during the process. But, the external-skin on the periphery of the billet, which is often partially solidified and contaminated with lubricants, should not be included into the casting as this can be a cause of reject for most structural parts. In this paper, a preliminary model is set-up using the LS-DYNA SPH formulation to follow the paths of the skin. Calculations carried out show that this approach appears to be very promising to predict the paths of contaminated skins into semisolid castings. It can then be utilized to design suitable molds and gating systems.

Jan 1, 2012

By Jun-ichiro Yagi

A mathematical model has been developed for simulating the blast furnace operation with carbon composite agglomerates charging based on multi-fluid theory and reaction kinetics. In this model, the behaviours of carbon composite agglomerates are considered on the basis of previously reported conservation equations and experimental research on the reduction rate of carbon composite agglomerates. A series of calculations are performed to examine the effect of charging carbon composite agglomerates. The model calculation gives two-dimensional distributions of process variables and information on the overall operational parameters. It reveals that in-furnace temperature levels significantly decrease and the reduction of carbon composite agglomerates is retarded with carbon composite agglomerates charging ratio. The furnace performance is remarkably improved with the increase in carbon composite agglomerates rate. The productivity tends to increase while coke rate and total reducing agent rate show decreases at the different degree.

Jan 1, 2006

By Dariusz Kopyci ski, Józef Dorula

The study proves that by introducing the iron powder and disintegrated steel scrap to low-sulphur cast iron still before the inoculation carried out with a conventional graphitising inoculant, the mechanical properties similar to those obtained during the inoculation treatment carried out on cast iron with the recommended high sulphur content are achieved. The said operation increases the number of crystallisation nuclei for dendrites of the primary austenite. In this case, the iron particles act as substrates for the nucleation of primary austenite, due to a similar crystallographic behaviour of the regular face centred cubic lattice The more numerous are the dendrites of primary austenite, the less free space is available in the interdendritic spaces for the formation of graphite eutectic grains, which makes the structure more refined (more eutectic grains) and the mechanical properties higher.

Jan 1, 2016

By Honggang Zhong, Xin Cao, Qijie Zhai, Hongmei Song, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of superheat on the solidification structure and ferrite/austenite phase transformation of a novel lean duplex stainless steel (DSS) was investigated on a setup, which designed to thermally simulate the continuous casting process. The results showed that the macrostructure of the samples all exhibited chill zone, columnar zone and equiaxed zone. The distance from chill zone to position of columnar to equiaxed transition (CET) moved from 51.0 mm to 39.8 mm with an decrease of superheat from 70 °C to 10 °C, and that the grains in the chill zone tended to be finer. In equiaxed zone, the fme and uniform grains were observed when superheat higher than 40 °C; while, coarse grains were found in samples poured at low superheat. Generally, the volume fraction of ferrite increased along the dendritic growth direction, and stabilized in equiaxed zone. The high superheat decreased the volume fraction of ferrite in equiaxed zone, while it had indistinctive influence on chill zone and columnar zone.IntroductionDuplex stainless steel with approximately equal volume of ferrite and austenite, offering an attractive combination of corrosion resistance and mechanical properties. [ l]. The production of DSS, worldwide application in structural engineering[2] and petrochemical industry[3], have increase by more than 100% in the latest decade[4]. But due to the sharp prices increase of nickel and chromium, lean duplex stainless steels which have lower contents of alloy elements were developed. They perform well in both mechanical and corrosion resistance[S, 6] and even have TRlP(Transformation Induced Plasticity) effect[?]. Nonetheless , the mechanical properties of DSS was affected greatly by the solidification structure, such as columnar to equiaxed transition (CET), grain size and phase content[8]. So, the solidification behavior of stainless steel was investigated widely"

Jan 1, 2014

By Alpagut Kara

Turkey is the fifth biggest ceramic tile exporter in the world. Considering the expectation that the Turkish tile sector continues to expand, further studies both on the improvement and the development of tile formulations are necessary in order to make the producers advantaged in the world market while maintaining the capital and running costs at reasonably competitive levels as well. In addition to such studies, waste management in tile manufacturing has also recently become an important issue. Accordingly, the industrial use of wastes in the traditional ceramic industry has been intensively investigated in the recent years. This work describes part of a detailed research project carried out jointly on the possible re-use of muds (raw production waste) from glazing and pressing lines of a local tile company in the development of new wall and floor tile formulations. In order to achieve this, the waste material was firstly investigated in function of chemical and mineralogical compositions. Then, the particular focus was given to the presence of the waste material in increasing amounts on the thermal behaviour and physico-mechanical properties of the re-formulated tile bodies. During the studies, SEM in combination with EDS, and thermal analysis techniques such as non-contact dilatometry were widely employed. The results indicated that it was possible to use the waste materials in the commercial tile production without deteriorating the relevant technological properties.

Jan 1, 2006

By E. J. Peuraniemi

Recently commissioned Kennecott-Outokumpu flash converting was developed to replace the approved but environmentally outdated Peirce-Smith -converting to satisfy the globally tightening emission regulations. In the present study, dust formation and reaction mechanisms of two copper mattes with different experimental parameters were studied in lean suspension conditions. Both mattes had very high copper content of approximately 75 wt% and low iron content of 4.5 wt% and 1.2 wt% Fe. A laboratory scale, vertical laminar-flow furnace with a low feeding rate was used to simulate the phenomena taking place in the reaction shaft of a flash converter. Experimental conditions included temperature of 1300 °C with reaction gas oxygen contents of 20 vol%, 50 vol%, and 75 vol%. In the experiments, sieved particle fractions were fed to the furnace and sampled after short reaction time intervals by quenching them into a water film. Collected particles were analysed chemically for their main elements to define their removal rates. Also, optical and scanning electron microscopy with EDS-analyser were applied to determine phenomena occurring during reactions. Kinetics of oxidation as well as ignition of particles are discussed. Changes in particle morphology, size, and composition are reviewed to describe dust formation and reaction mechanisms.

Jan 1, 1999

By Vladimir Lobanov, Pritchinm Alexander, Nikifor Ageev

"Sulfuric anhydride is one of the most voluminous technological emissions. The possibility of high-temperature SO2 oxidations without catalyst in presence of calcium-bearing filling materials (CaO, Ca(OH)2 and CaCO3) with obtaining of binding material on the basis of waterless calcium sulfate is studied. Due to application package HSC-4 the thermodynamic analysis of the specified interactions is made and following conclusions are drawn: 1) Reactions are feasible in the all range of investigated temperatures (400 – 1000 °?); 2) The best results should be expected at use of ???; 3) The heat of reaction does possible autogenous behavior of process. The researches have shown: 1) Practical possibility of the process; 2) SO2 oxidation without the catalyst is feasible in presence of ???, Ca(OH)2 and CaCO3; 3) The optimum temperature range is 600-800 °?; 4) The content of waterless calcium sulfate in a product reaches 48% that makes it possible to use as the binding material; 5) At excess of ??? the degree of SO2 collection is nearer to 100%. Introduction At processing of sulfide raw materials in metallurgical furnaces the significant amount of sulfur, mainly in the form of sulfuric anhydride is escaped. Rich gases (SO2>3 %) are used for the sulfuric acid or element sulfur production. Chemism of sulfuric acid manufacturing is based on catalytic high-temperature oxidation of anhydride. Poor gases of metal works (SO2 =2,5 %) and power combustion units (SO2 =0,5 %) after clearing discharge into the atmosphere. Commonly, to recovery of weak sulfuric anhydride the chemical and physicochemical methods are applied. A few chemical ways of recycling sulfur dioxide are applied practically. In a number of methods for SO2 recovery a pulp of metals oxides (magnesium, zinc, etc.) with formation of sulfites is used. In other case sulfuric anhydride is catch by weak sulfuric acid in the presence of an oxidizer (pyrolusite ore). Methods of absorption SO2 by solid sorbents, (carbon fibers, silica gels, zeolites) are known and put into practice. Regeneration of the saturated sorbents is realized by thermal decomposition or extraction. Obtained as a result high-concentrated solutions are a commercial product."

Jan 1, 2008

By R. W. Bartlett

A two step process for treating platinum group metal flotation concentrates Is described while experimental results. The process was designed to be simple and Inexpensive While yielding a high recovery and fast turnaround. Ii consists of electric furnace smelting of concentrate to remove gangue and produce a homogeneous sulfide matte containing all of the base metals and platinum group metals. Sulfide oxidation Is minimized during smelting to avoid Installing an acid plant In the second step, matte Is pressure-leached with oxygen In an acid sulfate system to dissolve Iron, nickel, ?and copper while leaving a residue highly concentrated In precious metals, and typically about 1% of the flotation concentrate mass, A batch process with oxygen titration against the base metal composition of the feed Is used to control the end point of the leach. Sulfides must be eliminated while minimizing the precipitation of hydrolysis products. The leach residue can be smelled to bullion to facilitate sampling accuracy.

Jan 1, 1989

By Evan Jamieson

The conditions under which various iron(III) oxy-hydroxides phases precipitate from iron(III) chloride and sulfate solutions at ambient temperatures (<60°C) are reviewed. Many of these precipitates are slow settling and gelatinous but ultimately transform into other more stable or crystalline phases. The phase that forms depends upon the rate of precipitation and pH. A comparison has been made of the iron(III) oxides formed upon the neutralisation of various iron(III) solutions with caustic, slaked lime or slaked magnesia which provide different rates of neutralisation and slowly dissolving solids with localised high pH. Mössbauer spectra of ferrihydrites precipitated under these different conditions are compared and interpreted. Particular attention is paid to the settling rate and settled volume which is likely to relate to industrial thickener and filter performance. It is shown that in pure chloride solutions, poorly settling ferrihydrite is usually produced at 20oC regardless of the choice of base. However in sulfate solutions fast settling precipitates are produced using lime and magnesia but not with caustic. In mixed chloride/sulfate solutions, optimum settling rates occur when the molar ratio of [SO4]2to Fe3+ is about 1:1 and when the sulfate concentration is <0.20 M. It is proposed that ?dense amorphous basic iron sulfate? or well-ordered ferrihydrite is formed on slowly dissolving lime or magnesia surfaces. Implications for industrial liquors are considered.

Jan 1, 2003