Search Documents

By S. R. Reddy

Thennodynamic properties of several quaternary systems are calculated using our recently modified Margules equations. The modified Margules equations are expressed up to infinite order in the vicinity of solvent. Quaternary system of one solvent and three,solute partials are derived. First order interaction coefficients of binary, ternary and cross -interaction parameters of quaternary system are used to'evaluate the partial functions. In the original fonn of Margules equations,derived partial functions are convergent and same 'as Unified ,Interaction Parameter Fonnalism. But considering up to infinite order of the Margules coefficients, the functions are divergent, in order to overcome this restriction, Margules equations are modified to get consistent equations. Derived partial functions are thennodynamica Hy consistent with Maxwell and Gibbs Duhem relations. The derived logarithmic activity coefficient of the solvent and solutes are consistent with the ternary systems. The calculated data, ie., activity coefficient values of nitrogen and interaction coefficients are in good agreement with the data of Fe-Cr-V -N. Fe-Ni-V -N, Fe-Cr-Ta-N and Fe-Ni-Ta-N systems.

Jan 1, 1999

By Wang Zhi

High-Mg-content concentrates are usually treated in Jinchuan flash smelting Furnace. Because the viscosities of high-Mg-content slag is very high, the operation of flash smelting becomes very difficult. To solve this problem, the viscosities of the semi-synthesized FeO-MgO-SiO2 slag of different compositions were measured. The results showed that when in the slag the weight percentage of MgO [w(MgO)] is 6-10%, the ratio of the weight percentage of iron to that of Si02, w(Fe)/w(Si02) is 1.1-1.4 and the temperatures are within 1473-1773K, the slag viscosities increased with the increase of W(MgO) and w(Fe)/w(SiO,). When w(Mgo)<6%, the smelting temperature should be controlled at I 300°C in order to to keep the smooth operation. When w(MgO)>10%, the temperature should be kept above I 633K. When the content of MgO is higher, a lower viscosity slag can be produced by decreasing the ratio of w(Fe)/w(SiO,). The appropriate ratio of w(Fe)/w(SiO,) for Jinchuan flash smelting furnace is about 1.2.

Jan 1, 2003

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003

By C. J. Newman

Production levels at the Kidd Creek copper operation increased during the 1980&apos;s by expansion of both the smelter and refinery and by major modifications to equipment which was causing bottlenecks. As a result, there was a significant reduction in the unit cost, some manpower reductions and hence a significant increase in productivity. In the last two or three years, there have been no major expansion projects leading to unit cost reductions and yet these have still been attained. This has been achieved by the development and implementation of various techniques designed to maximize the inherent potential of the operators and maintenance employees. This paper will initially describe the operation but will then place emphasis on employee involvement through such methods as idea awards, incentive schemes, loss control and continuous improvement programs. Organizational changes are discussed, particularly with reference to changes from the traditional operator role to one which encompasses maintenance skills and to cross-training of maintenance employees into multi-discipline fields. The effect of these changes are discussed by a review of the salient plant parameters of safety, production levels, cost and quality.

Jan 1, 1993

By Harsh Deep Chopra, Jason N. Armstrong, Susan Z. Hua

"Existence of anisotropic Curie temperature materials [E. R. Callen, Phys. Rev. 124, 1373 (1961); J. Appl. Phys. 32 S221 (1961)] is a longstanding prediction - materials that become paramagnetic at a lower temperature along certain crystal directions while remaining magnetically ordered in other directions up to a higher temperature. Validating Callen's theory, we show that all directions within the basal plane of monoclinic F e1Ss (pyrrhotite) single crystal remain ordered up to 603 K while the c-axis becomes paramagnetic at 225 K. Results prompt a re-evaluation of existing magnetic materials with a focus on magnetic characteristics along different crystal orientations above instead of below the ordering temperatures. Theoretical guidelines for identifying new materials with large anisotropy of Curie temperature are also given, and analysis protocol to characterize them in a self-consistent manner is discussed. Materials with such a large directional dependence of Curie temperature open the possibility for uniquely new devices and phenomena, including energy storage and spintronics devices.IntroductionThis paper is an overview of our recently published work on anisotropic Curie temperature materials [l]. As a background, ferromagnetic and ferrimagnetic materials are characterized by a critical temperature below which magnetic interactions prevail over thermal agitation, leading to the appearance of a spontaneous magnetization. Above this critical point, called the Curie temperature, thermal energy eventually overcomes magnetic interactions and the material becomes paramagnetic.It is less well known that the Curie temperature varies with the orientation of the crystal. In ordinary ferromagnets this orientation dependence of Curie temperature is negligible because of the vanishingly small ratio of anisotropy to exchange energy, i.e., the spherical or isotropic exchange term dominates. Thus Curie temperature in ordinary ferromagnets appears to be an isotropic property, and assigning it a single characteristic ordering temperature suffices. However, a 'small' difference is not equivalent to being the 'same', and under appropriate set of conditions the anisotropy of Curie temperature is predicted to become appreciable, as discussed in the following.In formulating the theory of 'anisotropic magnetization' [2, 3] E. R. Callen and H. B. Callen first discussed the ""interesting possibility"" of anisotropic Curie temperature [2] or ACT; Callen and Callen noted that it was W. J. Carr, Jr. who initially raised this question, and they discussed it in detail at the Conference on Magnetism and Magnetic Materials (NY, November 1960), see footnote on page 320 of Ref. [2]. Soon thereafter, E. R. Callen developed the theory underlying the anisotropy of Curie temperature and conditions conducive to its observation [4, 5]."

Jan 1, 2013

By Shengfan Zhou, XUEWEN WANG, Changjun Jiang, Mingyu Wang

In the process of extracting vanadium from stone coal by sulfuric acid leaching - P204 solvent extraction, Fe(III) can accumulate in the organic phase which reduces the extraction of vanadium. In order to eliminate the effects of the accumulation of iron, oxalic acid was used as the stripping agent to strip the Fe(III). The effects of oxalic acid concentration, phase ratio O/A, stripping time and shake velocity on the stripping of Fe(III) were studied. The results showed that the Fe(III) stripping rate can reach beyond 96% at the room temperature with 70g/L oxalic acid using an O/A of 2 at 160 rpm shake velocity for 20min. After 2-stage stripping, the concentration of Fe(III) in organic phase was 0.008g/L.

Jan 1, 2016

By Mohamad Omarei, S. M. Sadrameli

"The aim of this research work was to produce biodiesel (fatty acid methyl esters, FAME) from canola oil using KOH loaded on y-Al203 support as a heterogeneous catalyst. Different parameters such as effects of the molar ratio of methanol to oil, catalyst amount and reaction time on the yield were investigated. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were used for characterization of the catalysts. A biodiesel yield of 86.67% was obtained under catalyst preparation and transesterification conditions of calcinations temperature of 773 K, 4 h of reaction time at 338 K, and using 3.5 wt% catalysts and molar ratio of methanol/oil of 15:1. The leaching of potassium species in the spent catalyst was observed.1. IntroductionBiodiesel is an eco-friendly and alternative energy source for diesel engines that can be synthesized by transesterfication of vegetable oil or animal fat with alcohols [1 ]. There are four principal approaches to the synthesis of biodiesel involving the transesterification of the triglycerides of the plant oils and animal fats: base catalysis [2], acid catalysis [3-5], employing supercritical alcohol conditions [6] and enzyme catalysis [7]. The commonly used homogeneous catalysts are NaOH, KOH and their alkoxides. Homogeneous alkali-catalyzed transesterification is much faster than acidcatalyzed transesterfication [8]. However, a large amount of water is required to transfer the catalysts from the organic phase to a water phase after the reaction. Therefore, it is considerably more costly to separate the catalyst from the produced solution [9]. These disadvantages could be removed by use of a heterogeneous catalyst [10]. The use of heterogeneous catalysts eliminates the neutralization step, hence it results much easier to separate from liquid products. Also, they can be designed to give a higher activity and selectivity and to have longer catalyst lifetimes [11]. A large number of different heterogeneous catalysts have been synthesized for biodiesel production. For example, calcined Mg-Al hydrotalcites [12], zeolite and metal catalysts [13], metal oxides such as calcium oxide (CaO) [14], magnesium oxide (MgO) [15], zirconium oxide (Zr02) [16], and supported catalysts [17] have been investigated as heterogeneous catalysts. CaO and MgO are most frequently used heterogeneous catalysts for biodiesel production [18]. In this present work, we aimed at developing an efficient catalyst for transesterification of canola oil. We have prepared KOH/ Al203 by impregnation and applied to determine the optimum conditions for biodiesel production. Three different variables including reaction time , alcohol to oil molar ratio and catalyst loading with may influence the quality of the produced biodiesel were optimized. Moreover, SEM (scan electron microscope), XRD (X-ray diffraction) and XRF were used for characterization of the catalysts."

Jan 1, 2012

By Filiz Sahin

This paper presents a synthesis of TiB2 via carbothermal reduction method using a mixture of TiO2, B4C and C prepared in molar ratio of 2:1:3. Reduction experiments were carried out in a high temperature graphite furnace in a graphite crucible under argon atmosphere at different time (0, 15, 30 and 60 min.) and temperatures (1400, 1500 and 1600 °C). The products obtained were investigated using XRD technique.

Jan 1, 2008

By Emil B. Milosavljevic

The photochemical reactions of cyanide ion induced by light were investigated in the presence or absence of a titanium(IV) oxide semiconductor photocatalyst. The light sources employed were the sun and arrays of either mercury or fluorescent (cool white) lamps. The results obtained verify that cyanide decomposes much faster when TiO2 is present in the solution and that it is first oxidized to cyanate. However, contrary to the previous studies, it is established that cyanide is subsequently further oxidized via nitrite all the way to nitrate irrespective of the light source. As expected, the rates of the oxidation processes decrease with the illumination source utilized in the following order: Hg-lamps > sunlight > fluorescent lamps. As nitrate is a significantly less hazardous contaminant than cyanide, complete photocatalytic oxidation of cyanide to nitrate may be a viable method for decontamination of cyanide wastes. Contrary to previous claims, we find that cyanide is slowly photochemically decomposed even in the absence of TiO2. For example, with the mercury lamps as the light source, in two hours, cyanide concentration decreases to essentially zero; up to 7% was converted to cyanate and the remainder to unidentified products.

Jan 1, 1992

By Zhijing Zhang

A thermodynamic structure model for alkali borate melts is developed to describe the distribution of structural groups in the alkali borate melts as a function of compositions. Fractions of threefold coordinated boron atoms and fourfold coordinated boron atoms in the potassium borate melt are calculated for the entire composition range and compared with results reported in the literature. The model has been used for structural interpretation for the borate anomaly in viscosity, which regards the borate anomaly as a manifestation of the various antithetical effects caused by the introduction of alkali oxide into boric oxide. It has been found that the viscosities of alkali borate melts increase or decrease according to the changes in rigidity and spatial connectivity of the glass network structure, which is a function of temperature and composition.

Jan 1, 2001

By Xi-chang Shi, Yun-feng Fu, Bai-zhen Chen, Hui Xu, Xiang Xiao

"Extracting boric acid from saline brine by boron specific ion-exchange resin was investigated. Effects of resin amount, temperature, time and stirring speed on boron adsorption rate were studied in the experiments. The results indicated that the XSC-700 resin showed excellent boron absorbability and it performed better property for elution. The maximum boron adsorption capacity was 6.16 mg/ml in the optimum conditions: the resin concentration of 5 ml/(100 ml brine), the temperature of 60°C, the time of 5-6h and the stirring speed of 100 r/min. Boron was eluted from the resin with HCl and boric acid was crystallized by evaporating the eluate. The product of boric acid was in pure form as confirmed by XRD and other analysis techniques.1 IntroductionBoron has a number of minerals in nature such as tincal, colemanite, ulexite, and kemite, etc. [1-2]. Boron and its compounds are chemical materials of significant value. The principal industrial uses of boron compounds are in the production of glass, porcelain, enamels and detergents. Other uses include fertilizers, metallurgy, and nuclear shielding [3-4]. In recent years, because of the large-scale mining boron ore, ore resources are drained gradually. With the development of science and technology, the boron mineral resources will be unsatisfied with the future requirement. There exits abundant boron resources in salt lakes which cover about 40% of the total reserves in China. If we can obtain boron from salt lakes, it will produce great economic interests [5-6]. Therefore, actively seeking boron from salt lake and other resources in suitable conditions has become a hot spot in the research organizations of boron resources development and utilization in the world [7].There are many methods such as acid crystallization, solvent extraction and ion exchange processes suggested effective for boron extraction from aqueous solutions. Acid crystallization method has the shortcomings of complicated procedures, the pollution caused by hydrochloric and other ingredients returning to salt lakes during the extraction process. Although solvent extraction process increases the boron acid recovery efficiency, the cost of production is high [8-9]. However, Chelating resin extracting boron has the characteristics of simple process, easy operation and no pollution. It was reported that chelating resins containing functional groups show a high selectivity for boron extraction [10-12]. Therefore, ion exchange technique which is now the most practical application of significance and most extensively used ha"

Jan 1, 2011

By C. A. Silva

Ladle change-over, during continuous casting of steel, initiates transient flow in the tundish which influences the inclusion content and degree of mixing between two consecutive batches of steel. The mixing behavior in the tundish during this period is determined by the casting rate and the ratios of: inflow to outflow during the refilling period; and, the low liquid level relative to the nominal level in the tundish during the transiency. A 3:10 scale water-model of a typical one strand slab caster was operated in conjunction with a tracer technique to characterize the velocity fields for several combinations of these parameters. Steady operation, a limiting case of the transiency, provided a basis for comparison. High-order moments -- skewness and kurtosis -- of the residence time density function have been utilized as signature elements associated with a particular residence-time distribution for the system. A simple mathematical model incorporating the above parameters as well as a characteristic Peclet Number was successful in simulating the features of the transient period.

Jan 1, 1993

By Osamu Takai, Yoshiki Sato, Nobuhiro Tajima, Hiroyuki Sugimura

"Amorphous carbon thin films doped with nitrogen ( a-C:N) have been synthesized by means of shielded arc ion plating (SAIP). Their electron field emission properties, that is, threshold field strengths for electron emission and maximum emission current densities, were evaluated and compared with those of pure amorphous carbon (a-C) films prepared by the same SAIP apparatus. Among all of the fabricated a-C:N films, the a-C:N films with a N concentration of 23 %, which prepared using Nz arc plasm at a pressure of 1 Pa with applying a sample bias voltage of -100 V, showed the lowest threshold filed of 13.4 V/µm and the highest emission current density of 1.87 µAfcm2 at a field of20 V/µm. These field emission properties of the a-C:N film were much better than those of the a-C films. The best results obtained on the a-C film in this study were the lowest threshold filed of 15.5 V/µm and the highest emission current density of 0.052 µA/cm2 at a field of 20 V /µm. Nitrogen doping to aC was found to be effective for lowering threshold voltage for field emission and for increasing emission current density. The electron field emission characteristics of the a-C:N films depended not only on N concentration but also on chemical bonding state of nitrogen in the a-C:N films. The presence of the ~-C3N4-like phase, which contributes to improve wear resistance of a-C:N as well, distinguished by the NlsXPS peak at 400.5 eV is proved to be crucial in order to enhance field emission properties of a-C:N.IntroductionThere has been much interest in electron field emission from a cold cathode due to its potential applications in vacuum microelectronic devices including field emission displays which are expected as flat panel displays in next generation [l]. It is well known that efficient emission can be rather readily realized using tip-like shape cathodes, e.g., microfabricated three-dimensional electrodes [2], carbon nanotubes [3-5], etc. However, electron emission from planar surfaces is of particular importance since such a type of cathode is· simply fabricated and assembled into microelectronic circuits. Currently, amorphous carbon thin films doped with nitrogen (a-C:N) prepared by plasma processes have attracted attention because their threshold voltages of field emission are relatively low [6]. Among various methods for preparing a-C:N films, the process using arc plasma is of special interest since, in arc plasma, nitrogen is highly activated and new types of carbon nitride phase are expected to be synthesized. However, field emission properties of a-C:N prepared by arc plasma have been studied in less detail compared with that prepared by the other methods such as sputtering."

Jan 1, 2000

By Xia Hong-ying, Peng Jin-hui, Zheng Zhao-qiang, Zhang Li-bo

"Preparation of activated carbon from the walnut shell by microwave assisted steam activation was studied. Influences of the three parameters, activation temperature, activation duration and steam flow rate on the adsorption capacity and yield of walnut shell activated carbon(WSAC) were investigated,optimization process was obtained by the Response Surface Methodology (RSM). The optimum preparation conditions were as follows: activation temperature of 980°C, activation duration of 41 min and steam flow rate of 1.66 ml/min. The optimum conditions resulted in an activation carbon with an iodine number of 1025 mg/g and a yield of 52.17%, while the BET surface area, total pore volume and average pore diameter of WSAC were 1328m2/g, 0.72ml/g and 2.2nm respectively. The study supported the potentiality of comprehensive utilization ofWalnut shell and the benefits of the microwave heating.IntroductionActivated carbons are one of the most important adsorbent materials in modern society because of its abundantly developed pore structure, strong adsorption ability, high surface area and thermo stability. They have extensive application in many industries fields which include gas purification [1], catalyst supports [2] and other pollutants [3]. However, in recent years, the industrial production of activated carbon is facing the problem of raw material scarcity and high cost, which limit to be widely used. Therefore, the selection of an appropriate precursor plays an important role and it has become hot sport to seek cheap raw material to lower preparation cost. As a kind of reproducible resource, the waste from agriculture and forestry is a high-grade raw material for preparing activated carbon due to is high carbon content, such as palm shell [4], rice hull [5], and coconut shell [6]. At present Walnut shell is widely accepted to be a renewable source of biomass. According to statistics, there is more than 1000,000 tonnes of walnut shells are produced in China annually [7]. As a good precursor for activated carbon production, Walnut shell is a major agricultural waste, to make better use of the cheap and abundant agricultural waste, it is proposed for activated carbon production."

Jan 1, 2014

By Stephen K. Pave1

Over 1,100 tons per day of Fluid Catalytic Cracking Unit (FCCU) catalyst is used worldwide. During the cracking reaction, catalyst is contaminated by deposited metals including nickel, vanadium, potassium, copper, iron, sodium, etc. To compensate for contaminants, a portion of the circulating catalyst inventory is withdrawn for disposal and fresh catalyst is added. The DEMETR process takes spent FCCU catalyst and removes a portion of the metal contaminants, enabling the refiner to recycle demetallized catalyst, thus reducing the solid waste from the refinery. Through August, 1993, the operation of one unit for one refiner has resulted in the recycling of over 7,500 tons of spent catalyst.

Jan 1, 1994

By C. M. Wai

Metal species in solid and liquid materials can be extracted by supercritical carbon dioxide containing a suitable ligand. This in situ chelation-supercritical fluid extraction technique offers, several advantages over conventional solvent extraction including minimization of organic liquid waste generation and exposure of personnel to organic vapors. One unique feature of this technique is that metal species can be removed from solid materials directly using supercritical carbon dioxide as a solvent. Several ligand systems including dithiocarbamates, ß-diketones, organophosphorus reagents, and macrocyclic compounds have been tested for metal extraction in supercritical carbon dioxide. This novel extraction technique may have important applications for metal recovery and mineral processing.

Jan 1, 1996

Achieving continued economic growth with social equity within the natural limits of the Earth&apos;s &apos;eco-systems is the major issue facing the world today. The material and energy needs of the world cannot be met with the current ways of addressing this issue. The need for metals, an important class of materials, will continue into the future because their unique properties make substitution by other materials impossible in many applications and this need will continue to be met from primary metal production and recycling. However, the recycling rate will increase and the usage pattern of metals will change to reflect the environmental impact of their production and use. Pyrometallurgy has an important role in meeting the metal needs of the future since some metals can only be produced pyrometallurgically; the energy required to produce some metals pyrometallurgically is significantly less than by other methods; most metals are most efficiently recycled pyrometallurgically; and the release of harmful and toxic elements into the biosphere can sometimes best be controlled through pyrometallurgical processing. The development of strategies for pyrometallurgical processing for the future lies in the recognition that sustainable development calls for large step improvements in value delivered per unit of environmental impact over the entire supply chain. Pyrometallurgists can respond to this challenge by contributing to reducing the environmental impact of meeting metal needs using three broad strategies: "end-of-pipe" approaches to convert emissions into benign materials for storage or disposal; flowsheet redesign to limit or eliminate emission production; and improved recycling technologies. A number of examples are discussed to illustrate how the sustainability driver is already influencing the technological development of pyrometallurgical processes, and how these will develop further as the sustainability driver strengthens.

Jan 1, 2003

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By Huimin Lu, Shi Zhou, Lisha Yang

"The Zeolitic imidazolate frameworks (ZIFs) were successfully synthesized by applying a combination of ionothermal synthesis and microwave energies for rapid synthesis. The synthesis was proceeded under various conditions including different raw materials, reaction temperature as well as microwave irradiation time. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are new type of porous materials formed by inerratic polyhedral in three-dimensional. They are the ideal crystalline substances for gas separation and storage. The assynthesized samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA) and C02 adsorption test. Results illustrated that the synthesized samples had stable structure, high thermal stability (up to 530 °C) and C02 adsorption capacity (10.2 cm3/g at 0°C under ambient pressure). This novel method also showed great advantage with high energy efficiency, safe synthesis conditions, and rapid crystallization time (60 minutes).IntroductionNowadays, carbon dioxide capture has become imperative due to the global warming caused by the increase of C02 in the atmosphere, especially produced by the concentrated sources such as power plants [1]. Zeolitic imidazolate frameworks (ZIFs), also known as coordination polymers, are ideal crystalline substances for gas separation and storage due to their structure diversity, high thermal and chemical stability [2-5]. They are formed by inerratic polyhedra in threedimensional with large cages and small apertures. Traditionally, ZIFs are synthesized by solvothermal method in a sealed autoclave under autogenous pressure [6-9]. However, in order to generate the products, the solvothermal temperature should not be lower than 100°C according to the sovlothermal mechanism. Moreover, at such a temperature, molecules with a low boiling point (such as water) may generate high pressure in reactor which might cause danger [9]. Thus the synthesis requires the equipment to possess resistance to autogenous pressure and corrosion. Further, conventional solvothermal methods need a long time to prepare products, usually a few days, which is a large energy consumption and inefficiency. So it is interesting to synthesis ZIFs through other ways under mild reaction condition with high energy efficiency."

Jan 1, 2012

By R. Tunold, Y. J. Zhang

"The cathodic kinetics of aluminum deposition from aluminum chloridealkali chloride melts was studied by use of electro-cnemical transient techniques at 700 °C. Aluminum deposited as an insoluble product on a glassy carbon electrode and as a partly soluble product on a tungsten electrode. The deposition was found to be a simple diffusion controlled process involving the exchange of three electrons. The diffusion coefficient of aluminum chloride was calculated - 4.sx10-s cm2 ·S-I in AlCl3 -NaCl-LiCl melts and 2.6x10-s cm2 ·S-' in AlCl3 -NaCl-KCl melts. For AlCl3 -NaCl-CsCl system the diffusion coefficient exhibited some uncertainty due to nucleation. The determined rate constant of aluminum deposition reaction was on the order of 10-' -10-2 cm'S:' Constant potential electrolysis was carried out. TiB2 was well wetted by aluminum. The species of melts penetrated into graphite and glassy carbon but not into tungsten. The diffusion coefficient of species in glassy carbon was evaluated.IntroductionAluminum chloride electrolysis is attractive for its power saving of 30%. Different process to circumvent the conventional chlorization to obtain aluminum chloride economically, such as directly chlorizating mixture of Al~03 and C in a cell with A-shaped laminated bipolar electrodes by rising chlorine (1), or by use of a composite anode (2), will promote the electrolysis technology to be realized industrially. With the appearance of the Alcoa process periodically there are studies on the kinetics of aluminum deposition. Some discrepancies seem to exist on the mechanism of aluminum deposition. Borne studies (3,4,5) showed that the deposition of aluminum was hindered by diffusion process in the melts. M.Gabco et a1. (6) claimed a preceding dissociation of a complex being the rate controlled step. This paper presents our results on the mechanism of aluminum deposition from the study by use of transient techniques and some results from constant potential electrolysis."

Jan 1, 1988