Search Documents

By C. J. N. Buisman

THIOPAQ technology developed and marketed by PAQUES Bio Systems in Balk, Netherlands, has been successfully used at commercial scale at the Budelco zinc refinery in the Netherlands for the treatment of contaminated groundwater since 1992. In essence, THIOPAQ technology consists of two biological process steps in series: sulfate reduction to hydrogen sulfide (anaerobic) and sulfide oxidation to elemental sulfur (aerobic). The biogenic sulfide produced can be employed for the chemical precipitation of metals in solution either inside the anaerobic reactor or in a separate vessel. Since the solubilities of most metal sulfides are much lower than of their respective hydroxides, considerably lower effluent metal concentrations can be achieved with THIOPAQ systems than in neutralization processes which immobilize metals predominantly by hydrolytic precipitation. In recent years, PAQUES has made significant advances in the design and operation of aerobic and anaerobic bioreactors for metal-sulfur systems. Moreover, the company has increased its technology portfolio to allow the development of more process oriented applications of THIOPAQ technology. A new PAQUES designed plant at Budelco treating sulfatecontaining proceswaters will be started up in 1999. The sulfate reduction is accomplished in a 500 m3 reactor in which hydrogen is used as electron donor. The endproduct, ZnS, is used for Zn and H2S04 production.

Jan 1, 1999

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"For optimum smelting results, proper treatment of the feed is needed to ensure favourable conditions for ignition characteristics, heat balance, mass balance with tolerable impurity levels, and overall process economics. Feed preparation consists of physical treatments before drying (blending), chemical treatments before drying, (roasting, if required), drying itself and physical treatments after drying (fractioning, if required).Effects of fluctuation on mineralogy and moisture should be minimized by blending the concentrates in a bedding plant prior to drying. As an alternative to drying, additional treatments such as roasting for impurity removal may be needed for part of the concentrate.Sustainability, energy efficiency, utilization of waste energy, low gas and dust emissions, product quality, availability and occupational exposure reduction are decisive criteria in drying today. These criteria are best met by the Kumera steam dryer, which has the best energy efficiency, zero CO2 emission, lowest operational and maintenance expenses, and superior availability and product quality.IntroductionFeed preparation plays a crucial role in having a smooth smelting operation and also the overall smelting economics in metal production. Therefore, it is of significant importance for all copper, nickel and lead smelter operations in which sulphide concentrates are fed to the primary smelting furnace. Generally speaking, the higher the metal content in the matte after primary smelting, the more important the feed preparation. This is of particular importance in the direct blister (DB) process for copper production and direct oxygen nickel (DON) for nickel production.Bedding is the first stage in feed preparation. This is very important for the sake of smoothing the mineralogical fluctuation in the feed for better smelting control. Its importance increases as the number of concentrates available for the feed mix decreases."

Jan 1, 2012

By Brian Lightfoot

Ausmelt technology is a versatile bath smelting technology with application in many waste treatment fields at low capital and operating cost. Heavy metals extracted from wastes may be recycled to mainstream use and the slags produced will be inert and suitable for use as aggregate, shotblasting grit or other applications.

Jan 1, 1994

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By Yasuyuki Murayama

MF is the semi-blast furnace which has been developed at Mitsui Miike Smelter in the 1960's to treat vertical retort residue. The MF has also been tested for treatment of various recycling materials and wastes. Now various secondaries and wastes (steel dust, zinc leaching residue, Cu-Ag sludge, spent catalyst and spent rubber, etc.) are mainly treated. Powder materials are briquetted with reductant before being fed to the furnace. Products are crude zinc oxide, matte, non-hazardous slag and steam. Zinc and lead are recovered in oxide dust, and copper and silver are recovered in the matte. The MF furnace can be widely applied to many kinds of materials which contain such non-ferrous metal-valuables. In addition, the improvement in operation and technology has effectively made the unit capacity much larger. The MF furnace now has many advantages for these treatment processes.

Jan 1, 1992

By Helmut Attlfellner

The selection of the best process for the oxygen generator for a metallurgical process requires the determination of all aspects which impact the economics of this facility. Concepts and features of modern air separation plants will be presented based on installed facilities for various metallurgical processes. The special features of advanced automation' of oxygen generators with load following and optimization of power consumption, automatic restart and unattended remote controlled operation will be investigated.

Jan 1, 1992

By Tobias Pröll, Bernhard Kronberger, Joachim Rohovec, Werner Hölt, Hermann Hofbauer

"As this is only a first draft, more precise explanations as well as detailed schemes, figures and plots will be included in the final draft. The description og the 100 kW test rig will also be mor detailed as construction is ongoing and will be finished during the summer. Furthermore simulations are to be finished shortly; so details on combustibles and gas concentrations will also be included in the final draft.AbstractOxyFuel combustion is a key technology for the efficient separation of CO2 from fuel combus¬tion (especially coal). Since coal plays a minor role in the Austrian energy mix the application of OxyFuel towards other fuels (biomass, waste fuels) is interesting to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alter¬native fuels is also interesting from a strategic point of view in order to generate knowledge for operation of capture ready cofiring and waste/sludge-incineration plants. OxyFuel uses a synthetic mixture of 02 and recycled exhaust gas where the 02 content may vary. This supplementary degree of freedom allows improved operation especially for low calorific fuels. Heavy fuel oil addition for low calorific combustibles can be omitted when using OxyFuel combustion. Application of alternative fuels (wood, waste wood, municipal waste, sewage sludge) in a 100-kW CFB plant is investigated in combination with process simulation.IntroductionOxyFuel combustion is discussed as one of the key technologies for the efficient separation of CO2 from combustion of fossil fuels (especially coal). Since coal plays only a minor role as primary energy source in Austria, the broadening of the scope towards OxyFuel of other fuels like biomass or waste fuels is necessary to reduce greenhouse gas emissions from Austrian energy sector. The investigation of OxyFuel technology for alternative fuels besides the large coal-oriented projects is interesting also from the strategic point of view. The presented project aims at the generation of knowledge in order to design and operate capture ready cofiring and waste/sludge incineration plants."

Jan 1, 2008

By Roger N. Kust

Removal of heavy metals from industrial process streams is becoming increasingly important for _the recovery and reuse of values in process tails. Technology has been available for several years which removes heavy metals, from dilute (0.1-3.0 g/L) streams, as hydroxide or hydrated oxide sludges, allowing discharge of washed cakes with up to 60% solids. This paper reports on improvements to this technology which now allows treatment of streams with metal concentrations in excess of 60 g/L while eliminating the need for thickeners. Streams containing copper, iron, aluminum, chromium, nickel, zinc, cobalt and lead have been successfully treated.

Jan 1, 1992

By Kiyoshi Shibata, Jun-ichi Hayashi

"Steel making technology poses strong potentials for environmental protection in three direction. One is pollution control on steel making process itself. Japanese steel industry has cut down various type of emission drastically since 1970's. Secondary, those process technology can be applied to reduce environmental burden in other industrial sectors. One of the successful examples is municipal waste treatment facility. Thirdly, development of high performance steel products, such as high strength steel for automobile body, can contribute to improve environmental performance during their use, based on the concept of life cycle assessment. Some examples of the successful development and future task is discussed.IntroductionsStack and smoke used to be a symbol of energy intensive industry such as steel making. But, scenery of steel works and its surroundings have been completely changed, and steel products have been changing, as well. The steel making industry consumes huge quantities of energy and resources. Variety of technical development have been carried out to reduce the pollutant release. The steel industry in Japan has been making direct and indirect contributions to reducing of various kinds of environmental impacts through development of high-performance process and products: Its potential technical capability accumulated in steel making is fundamental and essential infrastructure for the vein systems of our society. In this paper, the activity of steel making industry for better environment is discussed"

Jan 1, 2000

By Shinya Hodoshima

A catalysis pair of tetralin dehydrogenation / naphthalene hydrogenation has been proposed in the present paper as a liquid organic hydride for operating stationary fuel cells. Catalytic naphthalene hydrogenation, having been commercialized since the 1940s, proceeds to generate decalin via tetralin as an intermediate. The storage capacities of tetralin (3.0 wt%, 28.2 kg-H2 / m3) are lower than decalin (7.3 wt%, 64.8 kg-H2 / m3) but both tetralin dehydrogenation and naphthalene hydrogenation are much faster than the decalin / naphthalene pair. Moreover, existing infrastructures such as gas stations, chemical tankers and tank lorries are available for storage, transportation and supply of hydrogen. With respect to the stationary fuel cells with large space for hydrogen storage, tetralin as a hydrogen carrier is superior to decalin in terms of fast hydrogen supply or power density. Rapid hydrogen supply from tetralin under mild conditions was only accomplished with the carbon-supported metal catalysts in the ?superheated liquid-film states? under reactive distillation conditions. In contrast to the ordinary suspended states, the catalyst layers superheated in the liquid-film state gave high catalytic performances at around 250OC. As a consequence, both serious coke formation over the catalyst surface and excessive consumption of exergy were prevented simultaneously.

Jan 1, 2006

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By T. S. Krishnan

Among the established permanent magnets, SmCo5 magnet occupies the foremost position as it offers a unique combination of high energy product, coercivity and curie temperature. The SmCo5 magnets are thus extensively used for high field applications. These are also best suited for use in environments where high demagnetising field and high temperature are operative. Also, for applications where high performance and miniaturisation are the over-riding considerations, the choice again falls on SmCo 5 magnets. The main deterrent to the widespread use of SmCo5 magnet is its high cost. Both samarium and cobalt metals are high priced, and the magnets prepared from their directly melted alloy are thus naturally very expensive. An alternate process involving calcium reduction of their oxide intermediates has, therefore, been studied and the alloy prepared by this process has been evaluated and found satisfactory for magnet production. The process essentially involves compaction of the charge mix containing samarium oxide, cobalt oxide (or metal) and calcium metal and' reduction of the charge compact at 1000-1300°C in hydrogen atmosphere, followed by water and acid leaching, drying and classification. The calcium reduction process offers three distinct advantages over the conventional melting processes: (i) The oxide intermediates are relatively cheaper and do not pose any handling problems. (ii) The operation temperatures are comparatively lower and hence precise composition control is possible as samarium losses due to volatilisation

Jan 1, 1989

By Lauri E. K. Holappa

The aim of the metallurgical process development is, nowadays, to search for the shortest, most economical, more environmentally friendly and sustainable route to convert raw materials to finished products. Recent progress in steelmaking processes ? BOF and EAF - has also motivated to search for more advanced casting technologies to shorten process route. Continuous casting, which became industrially feasible in the 1960s, is now a mainstream technology with over 90% share of the world steel casting. After the 1980s, the increase in steel production and consumption, particularly from automobile, construction and home appliances industries, required steel manufacturers to accelerate production with more concise procedures, so that near-net-shape casting took the trend of development in order to bypass and simplify the downstream processes, e.g. cold/hot rolling mill or extrusion mill, to directly obtain finished products with required geometries. Progress in flat and long products changed the industrial operation pattern, strengthened steel production efficiency, and formed the operation concepts of the integrated steelworks and mini-mills, respectively. Thin slab casting and strip casting have represented the most important progress and promise, in the recent years, of such innovations furthermore strengthening the production efficiency and, concurrently, coinciding with the demands of environmental protection and sustainability. This paper reviews the most recent progresses in near-net-shape casting and prospects the impacts to steel industries as well as the development trends of steel production, in general.

Jan 1, 2006

By Adam Gesing, Ron Dalton, Richard Wolanski, Larry Berry, Christopher Stewart

As the quantity of aluminum recovered from shredder scrap continues to increase, together with increased content of aluminum in automobiles, so does the economic incentive to further upgrade shredder scrap. This upgrade will be done by sorting and recovering the aluminum by specific usable alloy compositions. The metal recycling industry infrastructure needed to deal with the increased aluminum scrap supply already exists. It is an inverted pyramid structure that in North America comprises: 3000 scrap collection yards, 200 shredders, a dozen sink-float plants and one heavy metal sorting operation. The technology for upgrading aluminum sorted from shredder scrap is already either in industrial use or in the final stages of pilot plant development. However, the current automotive aluminum recycling infrastructure will need to adjust to deal with higher volumes of the metal from aluminum-intensive vehicles that will be appearing in shredder scrap -20 years from now.

Jan 1, 2000

By Ledjane Barreto, Tulio Flávio Accioly de Lima e Moura, Wilson Acchar, Antonio Carlos Silva da Costal

"Clays are common ingredients in pharmaceutical products both as exclplents and active substances. Clay minerals are naturally cationic exchangers and they may undergo ion exchange with basic drugs in solution. Smectites, and montmorillonite have been studied due their high cation exchange capacity as compared to other silicates. Recently a patented study reports the use of attapulgite as the encapsulating agents both for the protecting the active substance and modulating release into the body. Some clays such as kaolinite, smectites, talc, etc are also used as dermatological protectors. Sepiolite and smectites have the ability to form complexes with organic compounds with absorb ultra-violet radiation, enabling them to be used in sun screens with protection factors. The objective of this work is to characterize the attapulgite in order to study the potential use of this clay material in the human health.IntroductionSince the begimling of time, nature has served humanity as a source of various raw materials. Among these, clays such as kaolinite and ilitte are common ingredients in the tile production. Recently, special clay materials have been investigated in order to identifY new potential uses of these class of materials. Clay materials are natural raw material and have excellent properties such as low toxicity, good biocompatibility, making them a good material to be used in biological applications. Attapulgite (paligorskite) and sepiolite is so called special clays. These special clay materials are very sin1ilar and have a great potential to be used in some technological areas due their special catalytic, sorptive and colloidal-rheological properties [1-8]. Recently some works have reported the use of these special clays materials for many applications such as drug delivery, wound dressing, oil absorbent, pesticides, fertilizers [9-12]. Brazil has a significant reserve of attapulgite located in Piaui state, making the study of the potential of this mineral in special areas, very attractive. Attapulgite is classified a fibrous alluminous silicate material and shows the presence of micro pores and channels, fine particle size and high surface area making this material a good candidate alternative material to be used in many industrial applications [6,8,9,11,12]. The objective of this work is to characterize the physical and microstructure of attapulgite."

Jan 1, 2012

By William J. Pardee, Michael A. Shaff

"Deeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will accelerate productivity growth and materials science application through the ease with which they can be modified to accept new materials knowledge and sensors. Carbonization of resin matrix carbon fiber composites, specifically, is a violent solid state chemical reaction with large stresses due to gas pressure, matrix shrinkage, and differences in thermal expansion. The matrix strength falls sharply, then rises again during the process. At least two competing reaction paths are important; the first cleaves methylene bonds, reduces toughness, density and stiffness; the second reforms those bonds, ultimately resulting in aromatic ring condensation that increases density, strength, and modulus. Since these reactions have different temperature dependencies, one can expect to shift the process towards the second path by changing the heating rate, but that change must be accomplished without producing macroscopic interlaminar crack growth. To accomplish this, we employ gas sensors to infer matrix chemical state and acoustic emission to identify microstructural changes and to recognize brittle fracture. The latter does not prevent delamination, but is important in testing models for the causes of delamination and in improving the processing cycle. This paper describes a control strategy to accelerate the process while still lowering the risk of failure.IntroductionDeeper materials science knowledge from mathematical models and in situ material property sensors will be exploited in next generation factory process controllers to improve productivity and quality. These intelligent control systems will be more easily modified to accept new materials knowledge and sensors, thus accelerating productivity growth. Such a control strategy for carbonization control is described below.Carbon-carbon composites are time consuming and costly to manufacture. Processing methods have been developed empirically and are usually very conservative because the process often fails when any change is made. Apparently minor changes in materials or geometry can produce failures that are difficult to diagnose and correct. We will describe below several essentially unavoidable sources of variability. These are best dealt with by applying materials science to adapt (i.e., closed loop control on materials properties) the process in real time to reduce the effect of unavoidable model idealizations, material variability and environmental noise. The most critical issue in control of the carbonization process control is avoiding catastrophic delamination. The strategy developed below makes use of a priori materials knowledge and real time sensors to accelerate the now very slow process without destroying the material, and without requiring unreasonable resources to determine the statistical properties of the material."

Jan 1, 1988

By Ch. -A. Gandin, M. Rappaz

"The grain selection mechanism which occurs during the growth of columnar dendritic structures is routinely used in the investment casting industry to produce directionally solidified (DS) and single crystal turbine blades. However, the evolution of the grain density with increasing distance from the chill has rarely been correlated with the evolution of the grain texture. This contribution presents a three-dimensional (3-D) stochastic modeling approach which permits the computation of grain maps, pole figures and grain density evolutions in DS superalloys. These predictions are compared with measurements resulting from an automatic indexing technique of Electron Back-Scattered diffraction Patterns. This 3-D stochastic model, which applies to uniform temperature situations, has to be extended to the dendritic growth in a thermal gradient. As a preliminary step, a 2-D Cellular Automaton (CA) has been coupled recently to Finite Element (FE) heat flow computations in order to predict the grain structures in complex shape investment cast part. The application of this CAFE model to the investment casting of a turbine blade is presented. Considering these results, the extension of the CAFE algorithm to three dimensions is discussed.INTRODUCTIONThe selection of columnar grains during the directional solidification of alloys plays a key role during the investment casting of directionally solidified (DS) and single crystal (SC) components for aerospace applications [I]. This selection mechanism, leading to a competition of the dendritic network propagation at grain boundaries, has been the subject of many investigations. In particular, the study of Walton and Chalmers [2] is remarkable since it provides a link between the evolutions of the density and of the texture of columnar grains with increasing distance from the mold wall. Since this original work of Walton and Chalmers, two new tools have become available, which enable one to revisit the problem of grain selection in much greater depth. The first one is a fully automatic indexing technique of Electron Back-Scattered diffraction Patterns (EBSPs) [3-6] which directly gives the crystallographic orientation of the solid at any location of the specimen. Pole figures, orientation distributions, misorientations between grains can be visualized very easily with this technique. This information can be directly compared with the results of a second tool: a three-dimensional (3-D) stochastic model (SM) describing the nucleation and growth of grains in a uniform temperature field [6-9]. In order to extend this model to non-uniform temperature situations, a preliminary 2-D model has been developed [10]. It is based on a Cellular Automaton (CA) algorithm coupled with Finite Element (FE) heat flow computations. Since the details of both the automatic indexing technique of EBSPs and the simulation tools have already been published [3-10], only a brief summary is given here."

Jan 1, 1994

By Marie-Aline Van Ende, In-ho Jung

A thermodynamic database for the oxyfluoride system CaO-MgO-Al2O3-SiO2-Na2O-K2O-Li2OMnO- FeO-F has been developed based on the critical evaluation and optimization of all available experimental thermodynamic and phase diagram data. The developed database can be used for phase diagram and equilibrium solidification calculations for multicomponent systems and for understanding the solidification behavior of mold fluxes. Based on this thermodynamic database, a simple kinetic model was developed to simulate the interactions between the mold flux and molten steel using effective equilibrium reaction volumes combined with the thermodynamic database.

Jan 1, 2014

By James A. Warren

The phase field method has been successfully employed as both a tool to model heterogeneous materials and as numerical method for calculating the motion of interfaces and phase boundaries without explicitly tracking those interfaces. The method has been used to model a diverse suite of problems describing the microstructural evolution in materials. These models are derived from thermodynamic arguments and symmetry principles, and usually guarantee positive local entropy production for systems out of equilibrium. Descriptions of how phase field methods can be applied to the problems of solidification, grain growth, and electroplating will be presented.

Jan 1, 2001

By Jin Liu

The mechanism and rate of carbon reduction of each of the phases that are formed in the flash flame, i.e. sulfide (matte) and oxysulfide, was investigated. Graphite-slag reduction was conducted for comparison purposes. The objective of these tests was to measure the rate of solid graphite reduction of respectively matte, oxysulfide, slag, and matte+slag mixture at different temperatures. More in particular, these tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions and CO/CO2 ratios, reduced material assays, activation energies, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006