Search Documents

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Chris Mark

Perhaps the most significant development in coal mine ground control during the last century was the introduction of roof bolting during the late 1940's and 1950's. From an engineering standpoint, roof bolts are inherently more effective than the wood timbers they replaced. Roof bolts promised to dramatically reduce the number of roof fall accidents, which then claimed hundreds of lives each year, and they were initially hailed as "one of the great social advances of our time." Roof bolting also emerged at a time of rapid technologic transformation of the coal industry, and greatly accelerated the transition to trackless, rubber-tired face haulage. The U.S. Bureau of Mines quickly became the new roof support's strongest advocate. Some state agencies and miners were skeptical at first, but nearly everyone was soon won over. Case histories were reported showing that roof falls could be largely eliminated while productivity increased dramatically. Little wonder that, in the words of one contemporary observer, "roof bolting has been adopted more rapidly than any other new technology in the history of coal mine mechanization." Yet by the end of the 1950's, it was clear that roof fall fatality incidence rates had actually increased. It would be another decade before the superior ground support provided by roof bolts would clearly save lives, The story of how roof bolting was implemented by the mining industry, but took so long to live up to its promise, is a fascinating example of the interaction between economics, technology, regulation, and science. It still has important lessons for today.

Jan 1, 2002

By Richard G. Burdick

The Bureau of Mines', Denver Research Center has been conducting research for the past few years on the use of resistivity methods to locate abandoned mine workings. As this work has progressed, it is apparent that in some cases, in addition to detecting the old workings; stoping, precursive to surface subsidence has also been detected. This paper describes the Automated Resistivity method and discusses sites in Colorado. Wyoming. and Illinois where the subsidence phenomenon has been observed.

Jan 1, 1982

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By Tobias U. Papst

The German Ruhrgebiet is slowly transitioning into a post-mining state. It has been subjected to industrial-grade hard coal mining operations for more than 150 years. Due to a political decision, German hard coal mining will come to an end in 2018. By then the surface will have subsided up to 20 meters. After all mining activities in the area have ended, there will be no need to maintain the current mine water level. Accordingly, the company operating the last remaining coal mines has decided to let the water level rise to an as yet undetermined level. Alongside other issues that may be caused by rising groundwater levels, the protection of the area?s drinking water supply is of utmost importance. This notion is also represented by European and German law. The primary intent of the applicable laws is to protect the health of the citizenship. This means protecting ground water that may be used by humans from being contaminated by the mine water. This paper outlines the consequences of European and German legislature on mining aftercare using the example of one of Europe?s largest agglomerations.

Jan 1, 2014

By Anand Bhagwat

Surface control can prevent the falls of ground between primary roof support systems and rib support. Using existing industrial products, and adopting them for mining applications, has historically attained surface control in underground mining. However, the latest innovative solution, a revolutionary wire mesh product, is designed specifically for underground mining applications jointly by Bekaert and Orica. This knotted wire mesh, FlexKnot? 2500 and FlexKnot? 3500, uses smaller gauge, higher tensile strength wires, than a chain link fence or welded wire mesh. The higher tensile wire enables the mesh to achieve greater ultimate load-bearing capacity, with significantly lower overall weight. Test results, obtained at the National Institute for Occupational Safety & Health (NIOSH) Mine Roof Simulator facility, illustrate the comparisons of the new FlexKnot with traditional 8- and 10-gauge welded steel mesh. The FlexKnot is superior in deflection, load-bearing capacity, and stiffness?categories that are critical in achieving safer surface control. It also offers enhanced corrosion resistance because of the galvanized coating applied on the individual wires prior to the knotting process. Case studies from underground coal mine installations confirm that FlexKnot has the ability to significantly reduce installation cycle time and to minimize use and repetitive manual handling of individual mesh panels. An added advantage is the ability to supply FlexKnot in rolls for quick and easy handling for either rib or roof support application. When using rolls, the bolter can install the entire roll with one continuous forward motion, unlike the wasteful back and forth travel for mesh panel.

Jan 1, 2014

By B. N. Whittaker

The paper briefly reviews the type of support and stability problems encountered in mining tunnels in U.K. Carboniferous rock conditions, particularly the Coal Measures where almost all such tunnels are located. Stability prediction of mining tunnels is discussed and a computer-based model which deals with stratified rock conditions is described. Various schemes for monitoring the stability of mining tunnels are examined and the application of the results discussed. Comparisons between predicted and measured Closure values are presented for a major Coal mining tunnelling project at Selby in the North Yorkshire Coalfield. Conclusions are drawn concerning the application of the present prediction technique together with the importance of underground monitoring. Examples of different types of mine tunnel stability problems encountered in the U.K. Coal Measures are discussed and comments made on the secondary effects of tunnel peripheral rock weathering and corrosion of the associated support systems.

Jan 1, 1987

By Phil R. Ames, Anil K. Ray, Murali M. Gadde, John A. Rusnak

"Many factors can be responsible for coal mine roof falls including, mining geometry, stress conditions and local geology. In the Illinois Basin coal mines, roof instability is commonly attributed to the low strength of the immediate roof, which is also moisture sensitive. Recently, in order to understand the mechanisms of roof instability, numerical modeling has often been the preferred ground control analysis tool. Since roof materials can exhibit significant spatial variability, such modeling results may not represent every section of the mine. At the same time, it is not feasible to carry out numerical modeling for the full range of geological and mining conditions possible at a mine. Operationally, it is more convenient and highly practical to have a simple map that depicts the expected roof conditions, determined through either complex numerical models or simple empirical analysis throughout the reserve area. In this paper, a case history is presented that shows how a combination of simple empirical analyses of geologic data and past ground control experiences at a mine can be synthesized into a roof stability map, which can then be used to forecast future ground conditions. The usefulness of such a roof stability map will be examined in terms of the predicted and actual ground conditions encountered over a period of more than a year after the map was created.INTRODUCTIONA roof fall, which can result in fatalities and lost work time, is considered to be one of the most severe ground control hazards in underground coal mines. In general, there are many factors responsible for roof falls, including mining geometry, stress conditions and local geology. In the Illinois Basin, roof falls are commonly attributed to the weak nature of immediate roof rocks, and some superficial falls may be initiated due to moisture sensitivity. Some unstable areas also occur when the immediate roof is highly laminated.Numerical modeling is a useful tool used to understand the mechanism of a roof fall by incorporating site-specific parameters. In the past, numerical modeling has been used to explain the mechanism of roof falls as well as simulate· roof falls and cutter behavior, but such work had been strictly site-specific (Gadde and Peng, 2005; Ray, 2009). Because of the restrictions imposed by the input parameters, numerical modeling results cannot represent the entire mine. In the real world, mining conditions vary from place to place, and even in a single panel, modeling results valid at one site may not apply at another nearby site. At the same time, due to the lack of input data pertaining to rock characteristics and in-situ stress variations, it is not practical to carry out numerical modeling for each local area of the entire mine site. In addition to these difficulties, mine operators prefer simple tools to understand the ground conditions at their mine sites. One simple and commonsense based tool is the roof stability map. A stability map not only synthesizes the geologic and stress analysis data empirically, but it can also be used to predict future ground control issues at that mine. Because of this practical appeal, stability maps are more likely to gain mine operators' acceptance and be used in their planning operations. In this paper, a case study is presented on the development of a 'Roof Stability Map' that was principally used for roof fall prediction for a mine in the Illinois Basin."

Jan 1, 2010

By William D. Gallant

This paper presents the results of a joint cooperative research project between the CANMET Cape Breton Coal Research Laboratory and the Cape Breton Development Corporation to observe the subsidence profile over the stopline of 2 West panel, Phalen Mine. A novel technique was designed and Implemented to determine vertical displacements of the overlying strata from within a near horizontal borehole drilled over the 2 West panel. Restrictions on data collection techniques due to the submarine nature of the coalfield are discussed. Development and implementation of the borehole technique using a piezometer and inclinometer Is described. Performance of the instruments and profiles obtained by them are presented and compared. Recommendations for design improvements are made to Improve the efficiency of the technique.

Jan 1, 1990

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Leigh Sharpe

Dunng the last 5 years a United Kingdom colliery has utilised a yielding-pillar configuration to extract a relatively thick coal seam at a depth of 640 m. As part of ongoing research into the siting of roadways adjacent to extracted longwall panels, seved field monitoring sites were established at differing locations to investigate roadway stability and yielding-pillar performance. Characteristic roadway deformation has been identified together with strata softening pathways which indicate the temporal increase in the height of softening into the roadway roof. In the assessment of such a complex problem numerical modelling, using FLAC, has been shown to contribute vital additional information, and provide further insights into the mechanisms controlling strata behaviour.

Jan 1, 1998

By Gregory M. Molinda

An investigation was conducted to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure, and suggestions for controlling this problem are presented. Hazardous roof conditions identified in a number of mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52% of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath a number of valleys in the form of bedding-plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomenon, was found at mining depths as great as 300 ft. In situ horizontal stress measurements in a mine beneath a valley and the adjacent hillsides confirmed valley stress re1ief. Underground mapping showed that roof falls in excess of 100 ft in length and up to 25 ft high closely aligned with the valley axis. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress. Thickness of cover, valley shape, and the orientation of the valley relative to the maximum regional horizontal stress all influence the "valley effect" on roof stability.

Jan 1, 1990

By Bret E. Leisemann

The geomechanical environment in which highwall mining must operate represents a hybrid between surface and underground operations. Mine design must take into consideration the complexities associated with unsupported spans, pillars with extreme aspect ratios and the instability related to the interaction between coal extraction and the highwall stability. The rock mass adjacent to the highwall, and for a significant distance in, is affected by lateral stress relief and blast damage. This paper describes a rigorous site investigation program aimed at providing some of the input parameters for the design of highwall mining layouts at the Moura Mine and focuses upon defining the nature and extent of the relaxed zone behind the highwall. The combination of borehole imaging and C factor analysis allows delineation of blast damage and relaxation of the rock mass immediately adjacent to the highwall excavation, as well as the more subtle relaxation effects deeper into the rock mass. This has led to the formulation of a proposed geomechanical model for the relaxed zone for direct input into highwall instability analysis and mine design.

Jan 1, 1993

By Thomas M. Barczak

Roof support systems are necessary to provide stable mine openings and much research has been conducted to design a variety of roof support systems that will function in various manners to ensure that stable ground conditions are achieved. Despite these advancements in technology, mistakes continue to be made in the evaluation and/or installation that significantly degrade the support capability or lead to erroneous determinations of support expectations. The purpose of this paper is to discuss misconceptions about how roof supports perform and factors that impact their performance. The goal is to present practical information that will assist mine operators and engineers in selecting, installing, and evaluating roof support systems properly, and help them to avoid mistakes that can lead to erroneous expectations and potentially catastrophic results that may lead to roof falls. The paper is limited to a discussion of secondary roof support systems and powered roof supports such as longwall shields.

Jan 1, 2001

By S. MacGregor

The role of horizontal stress, its orientation and magnitude, in defining the behaviour of strata in underground coal mines has been well established. Poor panel layouts have led to gate end stress concentrations, roof falls and lost production. The ability to define the horizontal stress regime over a mine site has historically been limited to point measurements, in part due to technology and cost. Recent advances in the application of geophysical tools, notably the acoustic scanner (borehole televiewer) have resulted in a new technique to conduct stress measurements. By quantifying the nature of borehole breakout and the mechanical properties of rocks in which they occur, this technique provides the ability to: obtain a vastly greater number of measurements, both at different depths and spatial distribution, than other techniques such as overcoring or hydraulic fracturing readily obtain depth versus stress relationships define geotechnical domains on the basis of stress direction and in-situ stress magnitude for mine planning purposes This paper presents an overview of the technique and presents case histories in its application at a mine site in the Sydney Basin, Australia.

Jan 1, 2002

By David Newman

The Southern Appalachian coalfield has a long history of coal bumps that are attributable to a unique combination of topography, geology, and multiple seam mining. The high pillar stresses that generate a coal bump result from: i. mountainous topography where the overburden commonly exceeds 1,500 feet beneath ridges, ii. multiple seam mining, iii. thin interburden between active and abandoned mines, iv. thick beds of competent sandstone and sandy shale strata throughout the stratigraphic section, v. strong coal seams, and vi. irregular pillar and mining geometry in older room-and¬pillar mines. Coal has been intensively mined for more than 100 years in Eastern Kentucky, Southwestern Virginia, and Southern West Virginia. As a result, it is commonplace to have abandoned mines above and/or below active operations. Therefore, those conditions that generate coal bumps will be more prevalent in the future, as underground mining continues in Southern Appalachia. The focus of this paper concerns two coal bumps that occurred in the Kellioka seam where both undermining and overmining had occurred. The purpose of the investigation is to determine the magnitude and distribution of vertical stress that initiated the bumps, to identify bump-prone areas in the unmined reserve, and to recommend pillar centers and mining layouts to avoid future bumps. The state of stress in three vertically adjacent seams was examined using the LAMODEL boundary element program. Large, detailed numerical models were constructed of both bump areas and of the remaining unmined reserve block. The results of the numerical analyses were compared with those obtained using analytical equations.

Jan 1, 2002

By Stephen C. Tadolini, Robert Hawker, Peter Mills, Colin Grubb, Tom Meikle

"In unfavorable strata conditions, it is often necessary to install additional long tendon support as part of a primary support cycle. Although these support systems provide the required additional stability to the roadway installation does have a significant effect on the rate of development. To overcome the slow cure time of Portland cement-type grouts, the use of two component resin systems, such as polyurethanes and urea silicates, have become favorable. However, concerns over low modulus and creep properties has led to the development of a two-component grouting medium that displays the properties of traditional cable grouting materials with the rapid reaction times of pumpable resin systems. This paper describes product testing, application, surface trials, underground trials, and full-scale applications of the Tekthix System in a dynamic underground environment. INTRODUCTION Single-component cement grouts have been used to anchor long tendon supports for many years. They range from high- to low-slump Portland cement and can be slow-setting to fast-setting grouts. However, current cement grouting systems, which includes the grout and equipment, have some disadvantages: 1. Low-slump grouts require pumps that can handle a thick, high-viscosity grout, so choice of pumps is limited. 2. Pumping distance is limited with current cable bolt grout pumps; operators often tend to add water to allow pumping long distance, which adversely impacts the quality and strength of the material. 3. Fast-setting grouts tend to cause issues with pump and line blockages due to the reduced working life of these single-component materials."

Jan 1, 2017

By Stephen C. Tadolini, Peter A. Gray, Robert Hawker, Andrew Sykes

"Self-drilling rock bolts (SDRBs) that use pumpable cement grout to anchor bolts have been used successfully in the tunnelling and civil engineering industries for many years. Pumpable cement grout offers a considerable advantage in that the SDRB can be fully encapsulated right down to the bearing plate, including filling cracks and cavities in the borehole. However, cement grout cannot provide the immediate rock support required for the coal industry. This paper describes a new SDRB system that uses pumpable resin to anchor the SDRB in a borehole, which not only provides all the advantages of a pumpable grout anchoring system, but also provides immediate roof and rib support as required in the coal industry. This paper further outlines the latest developments in SDRB technology including (1) extendable self-drilling rock bolts, which can almost double in length during the installation process and are particularly suited to low seam heights and rib support and (2) pre-tensioned SDRBs, where a pre-tensioned load can be applied during the installation process. These new SDRB systems offer both considerable advantages in rock support and improvements in mining productivity.INTRODUCTIONThe mining industry is continually striving to develop more efficient methods to support the roof and walls of roadways and tunnels, and rock bolting has proven to be one of the most significant improvements in ground support over the last 50 years. Rock bolting is now almost universally used in the underground mining industry worldwide, and there are many different rock bolts available.Rock bolts are traditionally made from steel or fiberglass and are anchored into a borehole with a friction-anchoring device, such as an expansion shell mechanism; cement grout; or chemical resin. Friction-anchored bolts are widely used in the Australian metal mining industry, predominantly as short-term support. They are used in conjunction with resin-anchored bolts where there is a requirement for longer life. Resin-anchored bolts are used in the coal mining industry.Friction-anchored bolts provide immediate rock support, but their load transfer capacity is poor compared to resin or cement anchored bolts. In addition, friction-anchored bolts are more susceptible to corrosion than resin or cement anchored bolts."

Jan 1, 2010