Search Documents

By James R. Fahy, Lawrence A. Hansen, J. David Deatherage

A laboratory testing program was con- ducted to investigate the shear strength along specific soil-liner interfaces for five types of liners of varying thicknesses. Results indicated a bilinear relationship between shear stress and applied normal stresses ranging from 276 to 1000 pKa (40 to 145 psi). Friction angles along the soil- liner interface below the break point normal stress (7.5 to 19 degrees) were lower than those recorded above the break point normal stress (14.5 to 39 degrees ).

Jan 1, 1987

By David J. Dunn

Materials related problems at mines can be big ones - like a newly completed 1 -m (3.5ft) water pipeline burst during initial filling, grinding ball consumption at double the typical norms on startup of a new semiautogenous grinding (SAG) mill circuit or 30 open-pit haul trucks in the shop for new bed liners after less than a year’s service. Materials engineering provides solutions to these kinds of equipment problems by selecting good materials and designs, by trouble-shooting service failures and by maintaining high quality in vendor-furnished materials and components. Materials with good properties, correctly made and fabricated, correctly installed in mining and processing equipment, produce ore and final products reliably and efficiently. Materials engineering, applied during design phases, specification writing, and receipt and installation of materials, ensures that equipment will have the best possible shot at performing up to expectations. Good calls on materials properties - specifying state-of-art materials produced by competent manufacturers - help mine managers to reduce downtime and mining and processing costs. Materials that are improperly made or specified can make a mining operation less efficient or, possibly, uneconomical.

Jan 1, 1992

By Frederick W. DeVries, J. Brent Hiskey

Cyanide has been recognized for about a century as the most effective reagent for processing gold ores. Cyanide leaching has been adapted to various metallurgical settings and continues to be improved. However, in recent years attention has been directed to alternative lixiviants for treating refractory ores and concentrates, and to the development of less environmentally controversial substitutes for cyanide. This paper reviews some of the reagents considered as alternatives to cyanide and focuses on environmental implications for using these newer reagents.

Jan 1, 1992

By W. Stahl, K. Keller

In addition to classifying bulk material, vibration screens are commonly used in dewatering. However, the lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. First, in this report, the dewatering of bulk material are shown based on a physical model. Because of tile oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. A comparison between dewatering theory and practice are shown by measurements using coal, limestone, etc. Dewatering measurements conducted on a vibration screen demonstrated that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibility of improving vibration dewatering is described.

Jan 1, 1998

By Ronald J. Doll

The selection and matching of the conveyor drive components (Figure 1) determine the initial cost, long term costs, and how well the drive performance is matched to a project's long term production goals. This paper will cover the specification criteria and considerations that should be included in a conveyor drive specification. It will also review the practical aspects of the specification's intent and the solicitation of alternatives.

Jan 1, 1998

In order to analyze and quantify distinct environmental properties in the vicinity of sites, the Site-Specific Natural Resources Information System (SARIS) has been developed based on a Geographic Information System (GIS). SARIS is one of the fundamental databases of a collaborative research program aiming at the resource orientated analysis of metallic raw material flows with aluminum and copper serving as exemplary case studies. The spatial database incorporates all present production sites of ore extraction, refining and smelting. Environmental data for each location were derived from global digital survey data covering land cover, soils, morphology, climate, topography and population density. The main application of this database is the characterization of environmental safeguard objects, which may be affected by the activity of concern. This site-specific environmental impact assessment is used to determine the relevance of environmental issues based on the distribution pattern of sites in a global framework. The derived results are used to suggest a tailored indicator approach to measure progress and performance of industrial developments relative to the predetermined site-specific conditions.

Jan 1, 2003

By Thomas R. Kuesel

All engineering designs are based on assumptions regarding the behavior of the structure or facility being designed. These assumptions may be based more or less heavily on theory, but are credible only if verified by observations of field performance. Dr. Peck's "State-of-the-Art" paper has described the semi -empirical process of soft ground tunnel design, emphasizing the importance of records of field performance of actual projects constructed under a variety of conditions. This paper will present the principal results obtained from measurements made during construction of the soft ground tunnels for the San Francisco Bay Area Rapid Transit System. SCOPE The BART System comprises 75 route miles, including 14 miles of soft ground tunnelled subways in San Francisco, Oakland, and Berkeley. All tunnels are single-track sections, approximately 18 feet in diameter. Usually there are two parallel tunnels at the same level, but under Market Street in San Francisco there are four tunnels (two over two), and there is also a three-track section (two over one) in Broadway, Oakland.

Jan 1, 1997

By Jozef S. Stachulak

Inco Limited operates 11 underground mines in the Sudbury District. The mines are located on the rim of the Sudbury Basin, an oval with the axis in the range of 27 and 60 km. The ore dips to at least 3000 m below surface. The ores are mined primarily for nickel and copper. Total ore production from underground is in excess of 55,000 tons per day. Over 40 surface fans have been installed since the late 1960's. All of the fans are adjustable pitch, axial flow units. A major factor influencing ventilation design in the last 30 years has been the introduction of diesel equipment underground. Volumes per fan have ranged from 60 to 330 (cubic metres per second), with motors from 100 to 2500 hp. Fans of the axial flow type have been in common use for main fan installations at Canadian mines for many years. The standard arrangement has been to mount these fans horizontally, i.e. with the fan shaft and the long axis of the housing horizontal. This is a natural arrangement for an underground fan, but for a surface installation, a vertically mounted fan has definite advantages. The surface area taken up by a typical vertical fan installation is generally about one quarter of that with a horizontal fan of the same capacity. (1) This is not a problem with isolated fans and flat surface outcrop sites, but where the installation is to be near existing buildings, or where there are poor surface soil conditions, space and cost considerations greatly favour vertical fans. MAIN FANS INSTALLED There are 43 main surface fans in operation at 11 mines. Twenty-seven of these fans are supply units, and 75% of them are vertical installation. The remaining 16 units are main surface exhaust fans, with predominantly horizontal installation. Within the last five years, some 20 main booster fans have been installed underground at several mines. Axial flow fans, with adjustable pitch blades, are used for both surface and underground installations. Exhaust fans are equipped with stainless steel or cast aluminum blades. Main underground fans are arranged horizontally and the majority of them have a floating shaft between the fan shaft and the motor. (2) The size of the fans in service varies from 1.8 m to 5 m in diameter, with the majority ranging from 1.8 to 2.5 m. The pressure produced by these fans varies from 0.25 kPa to 2.0 kPa. At Inco Limited, two main fans in parallel are preferred, rather than a single fan, so that if one fan fails, the remaining fan can still supply up to 70% of normal air quantities, while the damaged fan is repaired. This requires closure doors on each of the fans so the fan can be isolated in case of failure. It is more expensive than a single fan, but results in less production interruptions. The fan installations are well away from sharp inlet and outlet bends. FAN DESIGN INTEGRITY Both the mine operator and the fan manufacturer must understand that the main fan is critical to the mine operation, and that everything technically possible must be done in design and manufacture to ensure the highest degree of reliability. Some of the design parameters and criteria, based on Inco experience, are outlined and discussed below. RESONANT FREQUENCIES AND HOUSING MODEL ANALYSIS Any fan assembly will have many different resonant frequencies. It is a challenge to the designer to arrive at a design in which forcing frequencies do not coincide with any of these resonant frequencies to produce unacceptable vibration levels in operation. Finite element analysis is a useful tool that can be used to identify the most critical of these, so that housing and blade stiffness can be adjusted to change any resonances that might be close to forcing frequencies. Shaft critical speeds should be at least 25% above the fan operating speed, and there should be sufficient separation between other resonant and forcing frequencies to avoid excitation that might result in high vibration levels. QUALITY ASSURANCE Radiographic Blade Examination Mine fan blades are normally cast in small lots. To ensure that the castings are sound, a full radiographic examination is recommended in the highly stressed lower 1/3 of the blade.

Jan 1, 1995

By A. S. Azman

The mining workforce experiences high rates of hazardous noise exposure and hearing loss. However, previous studies have identified specific behavioral and attitudinal barriers that keep miners from effectively acting to prevent their own hearing loss. NIOSH has developed several new hearing loss prevention tools and interventions that specifically target these barriers to prevention. The NIOSH Hearing Loss Simulator addresses motivation to take action and knowledge about the consequences of noise exposure. The QuickFit earplug test device and QuickFitWeb online hearing protection tester address barriers to effective earplug and earmuff use by verifying at least 15 decibels of protection. The NIOSH Roll-Pull-Hold technique helps miners obtain better protection through an easy-to-remember set of steps that improves attenuation by 9 decibels. The ?Inquiring Ears Want to Know? fact sheet helps miners to understand audiograms and to use them to maintain their hearing health. Each of these interventions can be used within the context of a comprehensive hearing loss prevention program.

Jan 1, 2010

By C. L. Barron, M. L. Smith, K. A. Prisbrey

SAG mill throughput is often a bottleneck to increasing plant productivity. Improved size distribution control in the mill feed can be used to increase mill production. This can be accomplished by controlling blast fragmentation as a function of energy input and rock characteristics. Such an approach requires the integration of rock fragmentation and comminution modeling. The optimal mill feed size distribution is determined by adapting a population balance comminution model to a measure of rock hardness or fragility, which is also related to the rock fragmentation that is achieved by blasting. The relationship between the size distribution and fragility of the feed and the mill's product and the critical size in a SAG mill is examined.

Jan 1, 1994

By T. P. Smirnoff, R. J. Redmond, K .. N. Murthy

To minimize disruption to the Hollywood District of Los Angeles, a mined station using the New Austrian Tunneling Method (NATM) was developed. This paper presents the key factors contributing to the settlements and dynamic behavior of the unique binocular station design.

Jan 1, 1993

By Jerome C. Neyer

Within most of Canada and the northern third of the United States, the soils overlying bedrock are of glacial origin. Tunnelling in glacial soils presents numerous challenges to the contractor, including abrupt changes in soil type, boulders and glacial erratics, water bearing fine sands and silts, toxic or explosive gases, and glacial till. This paper examines the available techniques for geotechnical exploration in glacial soils; the relationship between subsurface conditions predicted by various techniques and conditions actually encountered during tunnel construction; and potential improvements in the planning and implementation of geotechnical explorations. Case histories of geotechnical exploration and tunnel construction in glacial soils are also reviewed.

Jan 1, 1985

By Chuck Hornaday, Brad Miller

Geosynthetic clay liners (GCLs) are manufactured barrier layers containing a high-quality sodium bentonite clay attached or adhered to geotextiles or a geomembrane. The GCL's low permeability and high strength make it an ideal replacement for low permeability soil or clay liners for mineral extraction and processing containment applications. This paper will discuss the advantages of utilizing a GCL versus compacted clay in containment applications. Some of the advantages include: the GCL's lower permeability (5 x 10-9 centimeters per second (cm/sec)) and corresponding better composite liner leakage protection, the GCL' s greater resistance to desiccation, differential subsidence and freeze­thaw, and lastly, the ease and speed of installing the GCL. This paper will also detail a number of important case studies related to the mineral extraction and processing industry. These case studies include using GCL in two large reclamation capping projects, as a secondary liner in two gold heap leach pads, as a composite liner in a dam for stormwater runoff control, and lastly, as a primary liner for a tailings runoff diversion channel.

Jan 1, 1997

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By P. G. Semple, K. W. Major, P. Eng.

The recent increase in development of refractory gold deposits has resulted in changes to the traditional treatment processes. The selection of the preferred refractory treatment process is dependent on the mineralogy of the ore. One process, which has recently gained increasing attention, utilizes dry grinding and roasting of the whole ore. This paper will discuss some of the considerations to be addressed during the design of the process fl owsheet and what the effects of the various alternatives will be on the plant capital and operating costs. The paper will be based, in part, on current experiences with dry grinding, roasting plant design and start-up.

Jan 1, 1990

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By J. Cooper, M. W. Staub

Environmental management systems (EMSs) have been in use for more than a decade. US mining companies are only just beginning to adopt EMSs. This lag is primarily due to lack of market forces and lack of evidence that EMSs add value over standard compliance programs. Several recent studies concluded EMSs improve environmental performance and reduce costs. State and federal regulatory agencies are using EMSs as an innovative tool to streamline the regulatory process and achieve continual environmental improvements. The climate is right for the mining industry to adopt an EMS model that improves environmental performance and takes advantage of new regulatory programs.

Jan 1, 2004

By Jack W. Eloranta, Michael J. T. Orobona, Peter R. VanDelinder

Ore blending for process optimization is becoming an increasing factor for managing cost and productivity. Economic mining and processing a very low value ore in an extremely competitive market results in constant cost-cummng initiatives. The inherent conflict between the lowest possible mining cost and the lowest possible milling cost is reviewed here in the context of blasting for autogenous mills. Iron ore blending focuses on a number of properties-liberation values, weight recovery and concentrate silica being the most important. Other chemical and metallurgical factors are also commonly controlled. Recent research has fueled an emerging interest in blending on physical ore properties as well. Fully autogenous mills rely on the large, competent fraction of crushed feed to act as grinding media. Previous test work indicated that Hibtac mills require specific amounts of 6- to 10-inch ore. High recirculating loads require a steady influx of large rock fragments. Blast designs, therefore, are presently characterized by wide patterns and low powder factors. Current efforts are aimed at improving mill throughput while reducing overall energy costs. Based on research and published case studies and the advent of optical measuring devices, Hibbing Taconite Company has embarked on a blast optimization program to identify optimum mill feed and to design blast fragmentation goals for each geological unit and each mining area. This paper outlines the preliminary findings of an ongoing, broad-based team effort which requires close cooperation of geologists, mine engineers, crushing and milling personnel. Three specific areas of investigation are reviewed: I) Historical relationships between powder factor and mill performance, 2) Blast fragmentation modeling using the Kuz-Ram model, and 3) Drill

Jan 1, 2004

By Melvin E. Poad

INTRODUCTION The placement of concrete by means of pumping is one of the fastest growing practices in the construction industry and is widely used in mining applications. In¬troduced in the United States in 1933, this method has been adapted to many aspects of the industry, especially where space for equipment is either limited or inaccessi¬ble. Concrete pumping offers many advantages over other methods of placement. Using pumping equipment, the concrete mixture can be transported in a single operation from a central mixing site to numerous forms in many remote locations, eliminating the need for rehandling the mixture and reducing the labor costs to a minimum. Pressurized pumping provides an extra mix¬ing and blending step, resulting in concrete of improved uniformity and greater density. In turn, this produces high compressive strength and increased durability. Various placement defects can be reduced or pre¬vented by pumping. The steady and even flow of the concrete minimizes the form distortion and delays caused by vibration problems that are common to fast dumping of the concrete mixes. Segregation, planes of weakness, bleeding, and surface faults are diminished considerably. Perhaps the greatest advantages of concrete pump¬ing are the distances and volumes that can be handled. Depending upon the equipment used, pumping rates of from 8 to 115 m'j/h (10 to 150 cu yd per hr) can be achieved, with a horizontal range of up to 460 m (1500 ft) and a vertical range of up to 140 m (450 ft). Theoretically, almost any concrete mixture could be pumped. However, consistency is an important consid¬eration for efficient operation. Mixes that are too wet, too dry, too hard, or poorly graded can cause difficulties that increase the costs. Similarly, mixes containing aggregate material that is over the maximum size or that is porous and highly absorptive can also result in diffi¬culties and increased costs. For the best efficiency, the mix formulation must have a well-graded sand and aggregate combination, with enough fines to provide flowability. If additional water is required for pumping, additional cement must be used to meet the design criteria of the structure. Each pump manufacturer can provide recommended mix formulations for the specific equipment furnished. Since the 1950s, many improvements have been made in pumping technology. Originally, only rigid steel pipe of 168 to 245 mm (6.625 to 9.625 in.) diam was used; today, both rigid steel pipe and flexible conduit are available in diameters of from 76 to 203 mm (3.0 to 8.0 in.). Improved pumps have been developed, and the introduction of power-coordinated booms has in¬creased the versatility of concrete pumping. The older and more conventional placement methods can no longer compete with the flexibility, efficiency, and econ¬omy of the pumping method, and continued research and development can only improve the system and expand its use throughout the mining industry. PUMPING EQUIPMENT The three major types of concrete pumping units currently available are the piston pumps, the pneumatic pumps, and the squeeze-type pumps. Table I provides a comparison of capacities, horizontal ranges, and vertical ranges for pumps of all three types. Piston Pumps The simplest of all concrete pumps are the piston¬type pumps; they are available from many manufac¬turers. As shown in Fig. 1, each unit consists of a

Jan 1, 1982

The implementation of NAFTA in January 1994 was expected to have small but beneficial effects on the Mexican economy, mostly through increased investments. Mexico's mining industry was especially likely to benefit, as mineral investment funds would be diverted to the now safer Mexico and away from similarly endowed but more risky Latin American mineral economies. The results during the past two years have shown that it is government and macroeconomic factors that influence investment flows, rather than the fine tuning of trade flows through so called “free-trade" agreements.

Jan 1, 1998