Search Documents

By Laurence E. Snow

The conversion to the use of commercial grade ammonium nitrate (CGAN) for use in blasting at the Utah Copper Pit of the Kennecott Copper Corporation has presented unique problems for the Drilling and Blasting Department, In order to better understand these problems, a' picture of the Bingham Pit might be helpful. Some quarter of a million tons of ore and waste must be blasted daily in order to keep thirty-eight electric shovels operating. All material is blasted by "toe holes" of 24 to 28 feet in depth, drilled from prepared drill grades and sloped so as to bottom approximately 5 feet below the bench level. Horizontal spacing of these holes averages 22 feet, with exceptions being made where faults occur in the bank. These "toe holes" are drilled by 4-inch drifter machines, mounted on self-contained mobile drill units using .3-inch starter bits and bottoming at a minimum of 2 1/2 inches in diameter, "Toe-hole" drilling amounts to about two-thirds of the total drilling. In the higher bank sections of the Mine and wherever necessary, single rows of "down holes" are drilled to 28 feet in depth and spaced, on the average 23 feet apart. These holes are also drilled by a mobile drill. "Down hole" drilling amounts to about one-third of the total drilling.

Jan 1, 1959

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By James M. Barker, Richard O. Y. Breese

The recognition of perlite as a distinct volcanic glass, and of the arcuate fractures that often characterize these natural glasses, dates back at least to the late 19th century and perhaps into the 18th century (Howell, 1974). Some authors suggest that recognition of perlite dates considerably further into antiquity, perhaps to the 3rd century BC (Caley and Richards, 1956). Most recent definitions identify perlite by the presence of vit¬reous, pearly luster and by the presence of characteristic concentric or arcuate perlitic fractures. As discussed more fully below, arcuate fractures in perlite need not be megascopic. The textures of perlite which commonly occur in deposits range from dense to highly vesiculated to pumice-like. Thus, the classical definition of perlite is descriptively restrictive compared to the natural range of textures and neglects to address the issues of genetic origin and geologic occurrence. In spite of the petrological usage of the term perlite, the in¬troduction of expanded perlite aggregate into industrial markets caused the term to be applied as well to the lightweight, cellular aggregate that is produced through the rapid thermal expansion of milled perlite ore. Perlite is distinguished petrologically from other natural glasses by a silicic or rhyolitic composition by the presence of 2 to 5 wt% total chemical water held within the glass structure and often by the presence of pearly luster and onionskin-like perlitic fractures. Worldwide, occurrences are associated with Tertiary through early to middle Quaternary volcanics and with the glassy portions of silicic domes and flows, with vitric tephra, with the glassy chill margins of dikes and sills, and with the glassy portions of welded ash flow tuffs. Less commonly, perlite is reported in association with the glassy portions of volcanic plugs and lacco¬liths. The perlite carapaces that partially or fully comprise extru¬sive domes and flows are often thick and areally extensive, and thus provide commercially attractive targets for low cost open pit mining. Perlite tuffs and tephras are also important commercial sources. Mining costs are minimized by open pit quarrying and by either bulldozer ripping or blasting. Crushing and sizing facilities are generally close to the pits. Due to the low weight and large volume of expanded perlite, unexpanded perlite that has been crushed and sized is usually shipped nationwide directly to local markets where it is expanded and processed for distribution to end users. The vast majority of international trade is in unexpanded perlite. In the United States, the evolution of the expanded perlite industry can be traced to the late 1930s and early 1940s when expanded perlite aggregate was introduced into gypsum plaster and concrete markets as a substitute for vermiculite (Schundler, Jr., oral communication, 1991) and was promoted for use in a much broader spectrum of products (Howell, 1974). By the early 1950s, end user markets were well established and small expanders were numerous east of the Mississippi River. Today, mining and expan¬sion is undertaken throughout the world. Worldwide production of perlite is dominated by the former Soviet republics, the United States, and Greece. Total worldwide production of processed perlite during 1990 is estimated at roughly 1 778 000 tons (Davis, 1991). The physical properties of expanded perlite that give this prod¬uct unique commercial value include: low bulk density, chemical inertness, high insulating ability, nonflammability and fire resis¬tance, and its ability to retain water. These and other physical properties give expanded perlite value in such uses as: lightweight acoustical and thermal insulating aggregate; component in plaster, insulating cements and lightweight concrete; loose fill insulation; as aggregate in horticultural applications; and in milled form as filter aid. In the United States and Europe, the largest end use is within building construction products.

Jan 1, 1994

By Ramkrishna Agarwal

A low grade iron ore is mined underground at Grace Mine using the panel caving method. Most of the development work is located in footwall. The runways for LHD equipments are heavily supported with steel sets on five foot centers. The sets are embedded in two to three feet of concrete. The initial cost of support is one of the largest single costs of production. During the process of ore-win¬ning, supports frequently fail, necessitating expensive repair. There is no systematic pattern to the failure of supports. A rock mechanics program was launched to isolate causes and their relative contributions to the failure of supports. The preliminary results are presented. A typical portion of a runway is instrumented to monitor rock mass movements around the runway and the corresponding response of supports as various mining activities are carried out in the neighborhood. We believe that such a program is a prerequisite to any remedial measure to alleviate pressure problem at Grace Mine.

Jan 1, 1973

By Paul E. Epstein

Despite the controversies that have surrounded asbestos over the past 20 to 30 years, no knowledgeable authority has doubted the usefulness of this material. Were it not for the health risks associated with the manufacture and use of asbestos products, its physical and chemical characteristics would continue to be hailed as an undeniable boon to mankind. However, it has become clear over the past 30 years that like other major contributors to our modern industrialized society, asbestos must be handled responsibly and with the full understanding that lack of care can lead to injury, suffering and death. In this sense, asbestos shares characteristics with nuclear power, pesticides and even motor vehicle usage. It is unlikely that modern society would be willing to walk away from the benefits bestowed by any of these valuable resources. Rather, the appropriate response to the identification of danger is to define the type of risk, quantify its incidence, search for methods of decreasing the risk and implement programs to achieve the goal of minimization of risk. We should recognize at the outset that the risk cannot be diminished to zero without elimination of the material entirely from our midst. The concept of acceptable risk is a complex issue involving medical, legal, financial, moral and even psychological factors that defy precise quantification. In essence, the major danger produced by exposure to asbestos is its potential effects on the respiratory system. Despite the fact that asbestos workers have constant skin contact with the material and porbably swallow it in the course of their activities, inhalation of the fibers is recognized as the major health risk associated with its use. Aerosols of asbestos are inhaled not only by miners, millers and fabricators but also by urban dwellers who have no direct occupational contact with the material. This occurs because asbestos has been applied to our buildings and has been used in a wide variety of products that touch our daily lives. While it is estimated that three to four million people in the United States have been occupationally exposed to asbestos, the number who have been non-occupationally exposed is many times that number.

Jan 1, 1984

By J. D. Cooper

Previous research developed guide- lines to restrict the placement of air velocity sensors to areas of Low turbulence in underground nines. Even though these guidelines are theoretically correct, and may be easy to follow in underground coal mines, their application in small underground metal mines is difficult. As a result, study was undertaken at the Colorado School of Mines Experimental Mine to determine if an air velocity sensor could be placed in other locations with acceptable results. It was found chat by applying a variable calibration function to correct for changes in amounts of turbulence, instead of the previously used calibration factor multiplication, the sensor could be used successfully in areas of moderate turbulence.

Jan 1, 1984

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By George L. Atwood

The western phosphate field, one of the United States' great mineral resources, lies within the western states of Idaho, Utah, Wyoming and Montana. This Permian sedimentary deposit has been known since the turn of the century and since the 1920's has been mined for its phosphate content. Isolation from markets and relatively high mining costs have restricted development as compared to eastern United States deposits, but nevertheless a significant western phosphate industry has developed. Geographically the deposit covers an enormous area of about 337 000 km2 (130 000 sq miles). It covers Idaho from Pocatello east- ward, western Wyoming to the eastern flank of the Wind River mountains, and extends well into southwestern Montana and into a large area of northeastern Utah north of the Uinta Basin and east of the Salt Lake valley.

Jan 1, 1983

By Kendrick C. Hardcastle

Although the basic techniques employed in hydraulic pumping in open pit mining have been practiced throughout the better part of this century, only relatively recently have studies of' sufficient depth and scope been conducted to improve these techniques. This paper will point out the basic techniques involved and some of the more recently discovered data concerning hydraulic pumping, Inherent in all hydraulic transportation systems apart from the consideration of transportation cast, is the outstanding advantage of slurrying the matrix at the mining pit so as to provide a lengthy and thorough soaking and washing of the material while in the pipe line and thereby reduce the necessity for washing, scrubbing and other treatment in the beneficiation plant. This is quite important in view of the constant increase in demand for a cleaner product.

Jan 1, 1964

By A. S. C. Owili-eger

An efficient state-of-the-art dynamic model to simulate and predict the rate of water production in longwall coal mining operations was developed as a tool for mine planning purposes. The model can also provide an estimate of any potential resultant hydrogeological impacts of an operation via an array of element-specific single-valued parameters referred to as the field rating indices. The computational procedure was designed to fully exploit the benefits of hydrogeotechnology and utilize a combination of conceptual, physical, empirical, and numerical approaches to define, characterize, analyze, and evaluate flow con- trolling properties of fractured rock systems. The model presented here provides a dynamic prediction method for highly fractured flow; a practical tool in mine and water control planning; and a cost-effective means of assessing, based on the best available technology, the impacts of mining on the water resources within a mining environment to satisfy local and federal regulatory requirements. Unique features include consideration of laminar and non-darcian flow domains in double-porosity-pressure hydrogeological media.

Jan 1, 1987

By Nikhil Dhawan, Shrey Agrawal, SHAILA MIR

The current study investigates the effect of microwave processing on low-grade banded iron ore using charcoal, coking coal, and non-coking coal. Charcoal showed better microwave heating response at low temperatures, and the coals exhibit better heating response at higher temperatures. Low carbon dosage ~ 12% is sufficient to generate concentrate with 61.8% iron grade and ~6% for 94.8% iron recovery comprising of magnetite phase suitable for iron-making applications. The process separation efficiency of ~ 95% is achieved at 6% carbon dosage and decreases with an increase in carbon due to formation of the fayalite phase. The metallization degree showed a strong dependency on reductant dosage and achieved amaximumvalue of 22.7%at 18%charcoal. The comparison of ore with pure iron oxide and the synthetic mixture of iron oxide indicated that the underlying bonding due to banded structure enhances the Joule heating during microwave irradiation and thereby aids in attaining higher temperature and better separation.

Sep 21, 2020

By J. Mark Richardson

Steady-state flowsheet simulators for mineral processing plants have evolved to a current high level of utility and accuracy. Reliable, general-purpose, semi-empirical models now exist in nearly all unit operations categories particularly in the areas of comminution and classification. .These models, installed as user-selectable functions within the integrated frame- work of flowsheet balance-solver software systems, can be strung together to represent any plant configuration. In addition, CAD-like graphics, data reconciliation and model parameterization functions have become standard features of the current generation of integrated plant simulators. These advances have given engineers the capability to investigate many different plant scenarios while requiring a minimum of actual plant testwork. This paper describes a methodology and an integrated software package which are being successfully applied in a number of operating plants worldwide to predict plant performance under changing conditions. Those conditions which can be changed include effect-of ore type, feed size, water addition rates, equipment geometries and flowsheet modifications. By using data from actual plant optimization exercises in real mills, the paper illustrates and out- lines a technique which includes plant data collection, ore breakage testing, flowsheet simulation, model-fitting (parameterization), data adjustment and model experimentation. Brief descriptions of some unit operations models, such as autogenous mills and cyclones, are provided as examples of the current state of such models. Ore breakage testing and its relation to certain models is also discussed. Computer- generated size-distribution graphs, along with tabular data generated by the simulator, round out the presentation and serve to demonstrate the real- ism and accuracy of the models. The paper concludes with a partial list of cases where this technology has been successfully applied.

Jan 1, 1992

By Richard L. Bullock, Bruce Kennedy

Vince Lombardi once said, "Practice doesn't make perfect, perfect practice makes perfect." When it comes to building a mine that will operate at the optimum level for the set of geologic conditions from which it was developed, Lombardi's remark might be paraphrased to describe the problem: planning won't guarantee the best possible mine operation unless it is the best possible mine planning. Any sacrifice in the best possible mine planning introduces the risk that the end results may not reach the optimum mine operation desired. This section addresses many of the factors to be considered in the initial phase of mine planning. These factors have the determining influence on the mining method, the size of the operation, the size of the mine openings, the mine productivity, the mine cost, and, eventually, the economic parameters used to determine whether or not the mineral reserve even should be developed. A little-known fact, even within the metal-mining community, is that room-and-pillar mining accounts for most of the underground mining in the united States. According to a 1973 study on noncoal mining (Anon., 1974), more than 76% of the producing mines [of over 1089 t/d (1200 stpd) capacity] produced approximately 70 000 000 t (77,000,000 st) or 60% of the nation's underground tonnage of material by room-and-pillar mining. That same year, 96.8% of the nation's under- ground coal mines produced 262 950 000 t (289,911,000 st) of coal extracted from room-and-pillar mines (Anon., 1976). Thus, nearly 333 000 000 t (367,000,000 st) of the United States' raw material is produced from mines using some form of the room-and-pillar mining system. Because approximately 90% of all mining in the United States is done by some variation of room-and- pillar mining, it is appropriate to give special emphasis to the effects of the various elements of mine planning on room-and-pillar mining. The relationship of these elements to other mining methods will become apparent as the elements are described in later sections herein. TECHNICAL INFORMATION NEEDED FOR PRELIMINARY MINE PLANNING Assuming that the reserve to be mined has been delineated with diamond-drill holes, the items listed in the following paragraphs need to be established with respect to mine planning for the mineralized material. Geologic and Mineralogic Information The geologic and mineralogic information needed includes the following: 1) The size (length, width, and thickness) of the areas to be mined within the overall area to be considered, including multiple areas, zones, or seams. 2) The dip or plunge of each mineralized zone, area, or seam, noting the maximum depth to be mined. 3) The continuity or discontinuity within each of the mineralized zones. 4) Any swelling or narrowing of each mineralized zone. 5) The sharpness between the grades of mineralized zones within the material considered economically minable. 6) The sharpness between the ore and waste cutoff, including whether this cutoff can be determined by observation or must be determined by assay or some special tool; whether this cutoff also serves as a natural parting resulting in little or no dilution, or whether the break between ore and waste must be induced entirely by the mining method; and whether or not the mineralized zone beyond (above or below) the existing cutoff represents submarginal economic value that may be- come economical at a later time. *7) The distribution of various valuable minerals making up each of the minable areas. 8) The distribution of the various deleterious minerals that may be harmful in processing the valuable mineral. 9) Whether or not the identified valuable minerals are interlocked with other fine-grained mineral or waste material. 10) The presence of alteration zones in both the mineralized and the waste zones. Structural Information (Physical and Chemical) The needed structural information includes the following: * 1 ) The depth of cover. 2) A detailed description of the cover including: the type of cover; * the structural features in relation to the mineralized zone; * the structural features in relation to the proposed mine development; and * the presence of and information about water, gas, or oil that may be encountered. 3) The structure of the host rock (back, floor, hanging wall, footwall, etc.), including: * the type of rock; * the approximate strength or range of strengths; * any noted weakening structures; * any noted zones of inherent high stress; noted zones of alteration; the porosity and permeability; * the presence of any swelling- clay or shale interbedding; the rock quality designation (RQD) throughout the various zones in and around all of the mineralized area to be mined out; the temperature of the zones proposed for mining; and the acid generating nature of the host rock. 4) The structure of the mineralized material, including all of the factors in item 3 plus: * the tendency of the mineral to change character after being broken, i.e., oxidizing, degenerating to all fines, recompacting into a solid mass, becoming fluid, etc.; * the siliceous content of the ore; the fibrous content of the ore; and the acid generating nature of the ore. Economic Information The needed economic information includes: *1) The tons of the mineral reserve at various

Jan 1, 1982

By Austin Whillier

INTRODUCTION Use of air-cooling or refrigeration equipment in underground mines is needed when conventional ventila¬tion techniques do not maintain acceptable environ¬mental temperatures in working areas. Because refrig¬eration can be very expensive, it should be implemented only after all possible and practical steps have been taken to eliminate or reduce heat sources in the mine. As an example, to prevent the main ventilation fans from contributing heat to mine air, they should be located in the air return and not in the air intake. It is particularly important to prevent any direct contact between hot water and ventilation air, especially in mines which encounter large flows of hot fissure water. Any water hotter than the prevailing wet-bulb temperature of the ambient air must be removed by pipes located as close as possible to the water source. This hot water must not be allowed free contact with the incoming ventilation air at any time during the water's passage out of the mine. Although insulation of the pipes carrying the hot water is seldom necessary, direct contact between the air and the water must be prevented so the warm water cannot evaporate. REVIEW OF COOLING PRACTICES Spot Coolers vs. Centralized Refrigeration To eliminate a few specific hot places in an otherwise cool mine, it is possible to use devices known as "spot coolers." A typical spot cooler that uses chilled water is shown in Fig. 1. These devices consist of self-contained refrigeration units that are often mounted on rail cars for haulage to hot spots. The cooling capacities of such spot coolers usually are limited to about 100 kW or 30 "refrigeration tons." A refrigeration ton represents a cooling rate that produces 1.0 st of ice in 24 hr; that is a cooling rate of 3.517 kW (200 Btu per min). Typically, the electric-power consumption to drive the compressor motor of the refrigeration plant in mines is 1.0 kW per refrigeration ton, corresponding to a coefficient of per¬formance of about 3.5. The principal difference between spot coolers and centralized refrigeration plants is the method of re¬jecting heat from the refrigeration system. Centralized refrigeration plants always discharge heat into the reject or return airflow of the mine; often that is the primary influence in selecting the location for the underground refrigeration plant. Heat from spot coolers usually is rejected into drain water or into air that is not flowing to the location requiring the cooling. As a result, spot coolers remove heat from troublesome hot spots in the mine, injecting that heat-plus the electrical energy used by the cooling unit itself-into other working areas where the ambient conditions are cooler. In effect, this is "robbing Peter to pay Paul." In deep, extensive mines, spot coolers usually pro¬vide only temporary and, over the long term, expensive solutions to localized cooling problems. Centralized re¬frigeration plants are preferred for such mines, with cooling distributed throughout the mine as required. Fig. 2 illustrates a typical underground centralized re¬frigeration plant. Centralized plants lend themselves to improved maintenance at reduced costs while offering the economy of size. Refrigeration plants of larger unit sizes have considerably lower initial costs than smaller unit sizes. The remainder of this chapter is devoted to large refrigeration plants, with no further consideration of spot coolers. Cost of Refrigeration Total Cost: The total cost of refrigeration amounts to about $200/kW of cooling per year (1981 US $). This total cost breaks down into approximately three equal parts: 1) Financial charges, which include the interest and amortization on the capital cost of the initial installation, and the cost of necessary underground excavations. 2) Operating and maintenance costs which include the cost of the electric power to drive the refrigeration plant's compressors. 3) Distribution costs which include costs for pump¬ing, insulated piping, and air-to-water heat exchangers. The local cost of electric power, the number of operating months per year, and the method of refrigera¬tion distribution all contribute to the actual costs in¬curred in a given application. However, the variations usually are limited to no more than ±30% of the $200/ kW per year total cost figure. Cost Per Ton: Refrigeration cost per ton of mineral production can be calculated if the annual production tonnage from the refrigerated section of the mine is known. In most cases, this cost will be less than $1 .00/t. However, in deep mines with high rock temperatures, such as those found in South Africa, the total cost of refrigeration can increase to several dollars per ton of broken rock. Distribution In deep extensive mines, distributing refrigeration often accounts for about half the total cooling costs. As a result, careful consideration and planning must be

Jan 1, 1982

By Richard D. Harvey

Petrographic properties of carbonate rocks are useful guides to the utilization of these rocks in SO2-scrubbing systems. High porosity and fineness of grain are thought to be the principal properties that contribute to high dissolution rates of the rocks in the scrubbing liquor. Lake marls and chalks are the major types of carbonate rocks that have these properties. Lake marls are composed mainly of equant grains of calcite (mean grain size generally less than 4 microns) weakly agglomerated in- to larger, porous particles. The marls commonly consist of 80 to 90 percent CaCo3 as calcite and aragonite. Impurities are, for the most part, quartz silt and organic matter. The average pore volume for samples of lake marls (1- to 1.2-mm particles) is about 0.50 cc/g, which corresponds to a porosity of about 57 percent. The mean size of pores in these marls is generally between 1 and 2 microns in diameter. Surface areas of lake marls range from 0.8 to 6.8 m2/g. Chalks have grain sizes and shapes similar to those of lake marls, but they generally have smaller amounts of quartz and organic matter and minor amounts of clay minerals. Pore volumes differ from one chalk formation to another; the 1- to 1. 2-mm particles average about 0.20 cc/g, which corresponds to a porosity of about 35 percent. The mean diameter of pores in chalks tested ranges from 0. 15 to 0.76 micron. Surface areas of chalks range from 3. 2 to 20. 1 m2/g. In the United States lake marls are restricted largely to Pleistocene- age sediments that occur in the states around the Great Lakes. Chalk and chalky limestones are restricted mainly to the Upper Cretaceous and Tertiary strata in the Kansas-Nebraska-Colorado area and in the south- eastern states, from Texas to Florida. Results of laboratory tests of the relative dissolution rates of samples at pH 6 and 44°C indicate that, in addition to many lake marls and chalks, oolitic aragonite, pelecypod shells, and carbonate waste sludges from certain industrial plants also have high dissolution rates.

Jan 1, 1974

By William R. Barton

The domestic portland cement industry consumes more than 12 million tons annually of raw materials chemically similar to fly ash. How these materials are used and how fly ash can serve in their place are discussed. Factors influencing whether or not a particular plant will use fly ash in place of an alternate material are discussed.

Jan 1, 1968

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

Abundant beach and offshore resources of gold deposits are demonstrated along the coast of Alaska, and Nome is one of the richest places. Considerable amounts of mineral resources data were collected and stored in geodatabase of ArcGIS. In searching for the best model for the interpretation of the Nome offshore gold placer deposit and accurate estimation of the reserve, the data were processed and visualized using ArcGIS. The gold concentration data collected from the Nome offshore deposit are of characteristics such that: (1) near lognormal distribution of data, (2) high positive skewed distribution, (3) a small number of extreme values dominating the reserve estimation, and (4) apparent anisotropy of the variogram. These characteristics make the development of an interpolation model for the gold deposit a challenging task. In this study, it is determined that five geostatistical methods provided by ArcGIS with visualization capability, i.e., Inverse Distance Weighted (IDW), Ordinary Kriging (OK), Ordinary Kriging with lognormal transformation (OK-log), Simple Kriging (SK) and Indicator Kriging (IK) are suitable candidates for the development of an interpolation model. The five algorithms are evaluated and compared with each other in the study. Cross-validation technique is employed to examine the accuracy of the five approaches. It is determined that the OK and SK algorithms are not suitable for this dataset because of the difficulty of fitting the semivariogram model despite their lower RMSE (Root-mean-square error) and the higher RMSS (Root-mean-square Standardized). The OK-log algorithm does not provide satisfactory prediction either, because it places too much weight on the role of extreme values resulting in overestimation and extremely high RMSE. Reserve estimation of each blocks is conducted using each of the interpolation methods and compared with the reserve calculated using the conventional polygon method. The IWD and IK algorithm seem to provide estimations more agreeable with the conventional polygon method.

Jan 1, 2005

By John E. Wallace

A recent study by the New York Trap Rock Corporation has conclusively determined that the number of blasting complaints is directly related to the noise produced by the blast. In turn it has been known for some years that the noise produced by the blast is directly related to atmospheric structure of temperature, wind, and humidity in the vertical direction. Normally during daylight hours the temperature decreases with altitude at the rate of about five and one half degrees per thousand feet on a sunny day, and to somewhat lesser amounts on cloudy days. Consequently, sound travels slower with altitude because of the lower temperature, and the sound rays tend to bend skyward, and are soon dispersed in the atmosphere. Quite frequently, however, the temperature increases with altitude, and just the opposite effect is attained. That is sound rays are bent downward, and sometimes reach the ground with intensities approaching that at the source. When the temperature increases with altitude a temperature inversion is said to exist. Less frequently than these two atmospheric conditions a condition is observed where temperature remains constant with altitude. This is called an isothermal atmospheric condition, and sound passing through this type of atmosphere tends to travel in straight lines, neither bending upward nor downward. The sound will be greater than normal near the blast, but will dissipate rapidly with distance from the blast site with no zone or zones of silence.

Jan 1, 1962

By Robert L. Somerville

As more phosphate deposits are discovered and new mines are developed, the necessity of critically evaluating various rocks for phosphoric acid production recurs ever more frequently. This need is accentuated by the increasing number of, fertilizer plants being constructed on deep water at various locations to serve world markets and to take advantage of locally-available sulfur or sulfur-bearing ores. A major proportion of all phosphate rock mined is consumed by wet-process plants and this acid in turn is consumed, usually captively, in the manufacture of fertilizer. It is apparent, therefore, that the first question asked by the developer of a new deposit is - How will it work in a wet-process plant? and conversely, when developing a deep water, project, one of the early studies required is - Which of the available rocks shall we use? What is the correct price to pay? How do we compare one rock with another? The economic importance of even minor aspects of these questions

Jan 1, 1966

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997