Search Documents

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 degrees apart into the outer surface of a hollow cylindrical steel tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U. S. patent (3,914,992) assigned by the author to the Department of the Interior was granted October 28, 1975.

Jan 1, 1976

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Gregory R. Wessel

Sulfur is a nonmetallic element widely distributed in nature and of great physical and economic importance. It is the 14th most abundant element in the Earth's crust (0.06%) and an important constituent of animal and plant life. Sulfur has been known and used since ancient times for a number of medicinal and industrial uses. At present, most sulfur is used to generate sulfuric acid that is used in a wide variety of industrial processes, particularly the production of fertilizer. Because of this, sulfuric acid (and hence sulfur) consumption is often regarded as a good index of a nation's industrial development. In the past, sulfur was mined from surface occurrences in several geologic environments, and was used in relatively small amounts. With time, the uses of sulfur and sulfuric acid expanded, as has the need for larger quantities of these commodities. Sulfur is now mined from both surface and underground deposits, and is recovered as a byproduct from a number of industrial processes. Despite valiant efforts and years of work by sulfur explorationists and others, many aspects of sulfur mineralization remain controversial. Almost as controversial is the spelling of the word sulfur. The English spelling sulphur commonly is used outside America and in the American sulfur mining industry, but sulfur is the correct American spelling as approved by the American Chemical Society, the American Geological Institute, and many others. Those new to the American sulfur industry often find it puzzling to be reprimanded for using the correct American spelling. Sulfur resources are abundant and widespread, but the extent to which they can be classified as reserves is constrained by pre- vailing prices and extraction technologies. At present, sulfur can be economically mined from very few deposits. The sulfur industry is roughly divisible into two sectors: voluntary (or discretionary) and involuntary (or nondiscretionary). In voluntary production, the mining of sulfur or pyrites is the sole objective, and the recovery of the resource is as complete as economic conditions will allow. During involuntary production, sulfur or sulfuric acid (termed recovered sulfur) are produced as byproducts, and the quantity of the output is dictated by the demand for the primary product. Voluntary sulfur now accounts for only about 35% of the elemental sulfur produced worldwide, and most inves- tigators believe that voluntary sulfur will be less important in the future. Sulfur sources and products are described as follows (after Barker, 1983): Sulfur Sources: Combined sulfur-sulfur that occurs in nature combined with other elements, commonly referring to sulfides and sulfates. Cupriferous pyrites-pyrite containing minor amounts of cop- per sulfides. Hydrogen sulfide-a toxic gas that occurs in petroleum and natural gas. Involuntary sulfur-sulfur produced as a byproduct in response to legislative or process mandates. Native sulfur-naturally occurring elemental sulfur. Nonferrous metal sulfides-opper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfur complex organic sulfur compounds that occur in petroleum, coal, oil shale, and tar sands. Pyrites-iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfur-sulfur contained in anhydrite and gypsum. Voluntary sulfur-sulfur produced in response to market demand. Basic Sulfur Products: Acid sludge-contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-synonymous with crude sulfur. Bright sulfur-crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-solid crude sulfur crushed to -8 in. Byproduct sulfuric acid-sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-commercial nomenclature for elemental sulfur. Dark sulfur-crude sulfur discolored by minor quantities of hydrocarbons, ranging up to 0.3% carbon content. Elemental sulfur-processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-elemental sulfur produced from native sulfur sources by the Frasch mining process. Liquid sulfur-synonymous with molten sulfur. Liquid sulfur dioxide-purified sulfur dioxide compressed to the liquid phase. Molten sulfur-crude sulfur in the molten state. Prilled sulfur-solid crude sulfur in the form of pellets produced by cooling molten sulfur in air or water. Recovered sulfur-elemental sulfur produced from combined sulfur sources (including byproduct hydrogen sulfide, but sometimes referring only to sulfur from fossil fuels) by any method. Slated sulfur-solid crude sulfur in the form of slate-like lumps, produced by allowing molten sulfur to solidify on a moving belt. Specialty sulfur-prepared or refined grades of elemental sulfur that include amorphous, colloidal, flowers, precipitated, wettable, flour, and paste sulfur. Sulfur ore-unprocessed ore containing native sulfur.

Jan 1, 1994

By B. M. Kunar, C. S. N. Murthy, B. Rao K

Rock particle size has a very important significance in the mining industry, starting from blasting till the mineral processing. The present study was carried out to understand the particle size distribution in various sieves after conducting the ball milling process. The time of the grinding process was varied at different intervals. It was observed that 80% of the particles of both granite and marble rock samples passed through the 4800 μm sieve when subjected to grinding time of 40 minutes. Also, it was observed the number of particles that were retained in the smallest sieve of <75 μm was higher in the case of granite sample when compared to a marble sample. INTRODUCTION India is a major exporter of granite and marble stones. The major use of marbles and granites are constructing walls and floors. There are several machining processes that are applied before it is used as floors and walls. During this process, wastes are produced these wastes are used in various ways. These include use of powders for clay products (Segadães, Carvalho, & Acchar, 2005), as an additive in cement production (Aruntaş, Gürü, Dayi, & Tekin, 2010), to enhance the properties of brick ceramics (Saboya, Xavier, & Alexandre, 2007), in constructing bricks (Bilgin et al., 2012) and as an additive in concretes (Aliabdo, Abd Elmoaty, & Auda, 2014). Usually, the powder form of marble and granites are used as an additive in the above-mentioned applications. Powders of marble and granite are obtained through the grinding process. One such process of grinding is the ball milling process. In the ball milling process, a quantity of samples along with the charge quantity consisting of steel ball is subjected to a grinding process within a closed chamber as shown in Fig. 1. An even particle size can be obtained through sieving the material after subjecting it to grinding. The present study is planned to understand the particle size distribution in various sieves due to varying time and charge quantity in the experiment. Only time was varied to understand the amount of particle distribution in the case of granite and marble rock samples and a comparison is drawn. A statistical model was developed for marble rock specimen considering the data obtained by varying time and charge quantity in the ball mill experiment.

Jan 1, 2019

By D. Randall Crooke, Ron R. Jorgenson

Many coal combustion products (CCPs) have historically been unsuitable for placement as mine backfill because of their physical and geochemical properties and/or regulatory status. However, innovations in paste production and transport of CCPs utilizing the high, fine particle contents of these fine-grained waste materials and their water retention colloidal properties produce a non-segregating, self-cementing material that may be environmentally suitable for placement as mine backfill. Both industry and the regulatory agencies are enthused by the possible cost reductions, both in design and construction of disposal sites, and the reduced environmental impacts of CCP realized by implementation of this new use/disposal technology.

Jan 1, 2001

By M. C. Fuerstenau

Collophane, cryptocrystalline fluorapatite, is examined as a substrate for plant water and wastewater remediation. The attenuation of Fe3+, Cr3+, Fe2+, Cd2+, Hg2+ and Pb2+ is presented as a function of metal ion concentration, amount of collophane, initial pH and conditioning time. TCLP results for Pb2+ contaminated collophane are presented. Mechanisms of adsorption for divalent and trivalent species are suggested. Key words: Collophane, Wastewater remediation, Heavy metal removal

Jan 1, 2003

By William D. Mayercheck

The introduction of continuous mining machines in the late 1940&apos;s prompted the mining industry to reassess shuttle car batch-type haulage. Between place changes, the continuous miner could cut and load coal on a nearly continuous basis, but after loading a shuttle car, the high-capacity machine had to wait until the second shuttle car came inby and spotted itself under the miner tail boom. Thus, the wait-for-shuttle-car delay periods became the new bottleneck for increased coal production from the mine section. Recent studies have shown that nearly 25 pct of the continuous miner cycle time is consumed by delays in the haulage system, usually waiting for shuttle cars. Computer simulations of a face operation indicate that up to a 45 pct increase in coal production may be realized through the use of a continuous haulage system, assuming of course that the outby haulage system can handle this increased capacity. Coincidently, there are recent claims by some mines using continuous face haulage of a production increase of 45 pct compared with shuttle car haulage. These documented production records, computer simulations, and common sense indicate the potential of continuous face haulage in underground coal. The late 1960&apos;s and early 1970&apos;s saw several mining machinery manufacturers market mobile bridge carrier and piggyback bridge conveyor continuous haulage systems for use in underground coal mines. These systems have shown limited potential in some mines and outstanding success in others. It appears that no one system can be universally applicable to all underground mining conditions; thus, the Bureau of Mines has conducted extensive research over the last few years to investigate different types of continuous haulage systems for use in high and low coal seams that will advance the state of the art.

Jan 1, 1977

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By Ronald P. Geitgey

Pumice and volcanic cinder are volcanic rocks characterized by a cellular structure. They are formed as gases (primarily water) dissolved in molten rock, or magma, exsolve to generate a froth that cools and solidifies into rigid foam. The cells or bubbles are referred to as vesicles and they range in size from a few thousandth of a millimeter to several centimeters. Due to their vesicular character, both pumice and cinder have lower density and higher porosity than most other rock types, and, as the vesicle walls are broken, sharp cutting edges are continually generated. These properties are the basis for their commercial value as lightweight aggregates, insulators, absorbents, and abrasives. There is a certain imprecision in the terminology applied to volcanic products, reflecting to varying degrees the diversity of volcanic rocks, the relative youth of volcanology as a distinct field of study, and customs and practices of commercial trade. In general terms, pumice is light colored (white, gray, pink, pale yellow, or brown) and highly vesicular, usually with vesicle walls that are visibly glassy. Many pumice fragments are light enough to float on water. Pumice is readily cut by steel tools and some can be crushed by hand. Individual pumice fragments may range from 1 or 2 m in one dimension to c1 mm. Commercially, finer fragments are called pumicite or volcanic ash. In volcanology the term ash refers to any fragment c2 mm in size regardless of its composition. Cinder, or scoria, is dark colored (black, red, brown) with thick vesicle walls that appear dull or stony and that may exhibit iridescence. Cinder typically is heavier than pumice and has a higher crushing strength. In volcanology the term scoria refers to dark vesicular material throughout a wide size range while it is common commercial practice to use scoria for larger fragments (usually greater than 2.5 cm) and cinder for smaller fragments. GEOLOGY Composition and Physical Characteristics Most pumice is silicic ranging from 60 to 70% SiO2, that is, dacitic to rhyolitic in composition. Pumice of less silicic composition, including basaltic, occurs but it is less common and does not have extensive commercial use. Scoria and cinder are typically basaltic to andesitic with approximately 50 to 60% SiO2. Pumice and cinder may contain phenocrysts of feldspars and various ferromagnesian minerals that crystallized in the magma prior to eruption. Fragments of rock through which the magma has passed may be entrained in the melt and wall rock may be fragmented and admixed during an explosive eruption. Some scoria particles have lithic fragment cores. Phenocrysts and lithic fragments are relatively unimportant in cinder end uses but their presence may be detrimental in certain pumice products. Pumice typically has vesicles <1 mm in size separated by thin walls. Vesicle shapes include irregular, spherical, elliptical, and elongate to the point of being tubular with a silky appearance (Fig. 1). In some pumices, the vesicles are interconnected making the fragments permeable and highly absorbent; in others the vesicles are isolated forming a highly porous but very impermeable pumice. Floating masses of pumice fragments from the eruption of Krakatoa in 1883 were reported in the Indian Ocean for up to two years after the eruption. Vesicles in cinder are larger and range from spherical to highly irregular in shape with much thicker walls and abundant interconnections. Scoria and cinder are typically heavier, porous, and do not float. Density and hardness of pumice must be expressed precisely to avoid confusion. Density may refer to the glass itself, the apparent density of the vesicular pumice particle, or the bulk density of pumice in a deposit or in a product. Pumice glass has a specific gravity of 2.5 or more depending on its composition. Pumice fragments typically have a specific gravity of 4.0 and so will float on water, at least until enough vesicles are saturated to cause them to sink. Expressed as density, pumice fragments typically weigh less than 1 g/cm3. Depending on moisture content, particle density, and particle size distribution, the bulk density of pumice typically ranges from 500 to 700 kg/m3. Typical bulk densities of cinder range from 700 to 900 kg/m3 for material used as lightweight aggregate while the bulk density of cinder used for highways and railroad ballast may be considerably higher. Hardness in pumice may refer to the glass vesicle walls, possibly including crystals or lithic fragments, or to the apparent hardness of the particle as a whole, which is more a measure of the strength of the vesicle structure. Pumice glass typically has a Mohs hardness of 5 to 5.5. A pumice particle may have a much lower apparent hardness and be easily cut with a knife or steel saw because the vesicle walls break readily. Pumice and cinder are primarily pyroclastic deposits formed as fragmental products of volcanic eruptions. Several classification - systems differing in various details have been proposed for pyroclasts and pyroclastic deposits based on particle size (Fisher, 1961, Schmid, 1981, Cas and Wright, 1988). Generally, particles >64 mm are referred to as blocks or bombs depending on their shape. Particles between 64 mm and 2 mm (4 mm in some schemes) are called lapilli and smaller particles are called ash. These names may be modified by compositional terms, for example pumice lapilli or scoria lapilli. Most commercial deposits are composed of fragments in the lapilli size range. In the United States, pumice fragments having one dimension of 5 cm or more are legally defined as block pumice. The procedures for acquiring pumice from federal land are determined in part by this definition and are described in a later section.

Jan 1, 1994

By Greg Watson, Dennis Ofiara

"TBMs have been used in mining in decades past, but their use has been limited and sporadic, due to both perceived and actual application difficulties. With new technology and mounting success stories, this is changing. For both coal and metals mining, deep ore bodies require long access tunnels, and an efficient and economical method of reaching those deposits. Today, mining engineers are considering TBMs as part of the overall mine development plan. Planned TBM mine drifts are not only longer, but have more complicated trajectories. Mine development TBMs will have to cope with varying geology, potential for high water inflows, steep gradients, and high temperatures. TBM systems are being planned to cope with such difficulties. TBM systems will be considered and increasingly deployed for mine development, even if commodity prices remain low. TBMs can satisfy the need for increased productivity, better life of mine infrastructure, and safety. Effective conveyor systems are essential to support TBM operation in many mining applications. Many mine development tunnels are slopes, driven down at the steepest practical gradient to reach the deep ore body. Conveyors are often the only safe and effective way to haul the TBM muck form such tunnels. This paper will review the historical use of TBMs in mining, and will discuss the 2015 status of TBMs and conveyor systems in mining, and the special requirements and adaptable features needed in order to make efficient TBMs a reality in mines worldwide.HISTORICAL USE OF TBMS IN MINING APPLICATIONS The first successful hard rock TBM was invented in 1954. Over the next decades, TBMs have been used in many mining applications: Mine access drifts in several Spanish mines •,White Pine Copper Mine, USA •,Selby Coal mine drift, UK •,Coal slopes in Appalachia, USA •,German coal mines accdess drifts, several mines •,Magma Copper San Manuel, USA •,Cape Bretton Undersea Coal Slopes, Canada •,Stillwater Mines, USA"

Jan 1, 2016

By Gary A. Campbell, William A. Vogely

INTRODUCTION The theory of mineral demand often is slighted in the study of mineral economics. The supply side of the mineral industries usually commands a great deal more attention and effort by mineral economists than the demand side does because the study of mineral supply includes topics such as exploration, resource availability, and exhaustion theory that are generally considered unique to the mineral industries. Mineral demand, on the other hand, is thought of as being more general in nature and therefore of less concern to mineral industries specialists since it is similar to the demand for other inputs of production. This similarity with other inputs of production, however, does not negate the importance of a thorough understanding of mineral demand. It is the interaction of supply and demand that determines market behavior and not supply alone. Mineral demand is a key component among the factors that influence mineral production; there- fore, a good understanding of mineral demand can give one better insights into the industry behavior and trends than one would otherwise have. A strong working knowledge of the demand side of the mineral industries is a powerful tool for analyzing and predicting mineral market behavior. The material presented in this chapter does not depend on any special background in economics and should be accessible to all interested readers. The chapter is organized so as to permit an orderly progression of the basic topics of the theory of mineral demand while allowing digressions on related issues of special interest. The first section of the chapter is on the determinates of mineral demand. The discussion be- gins with the introduction of consumer demand and some of the necessary terminology of economics and proceeds to the particular case of the derived demand for an input of production such as minerals and the characteristics of such demand. The second section of the chapter is on the response of mineral demand to changes in economic variables like price and aggregate income. This second section of the chapter be- gins with a general presentation of elasticity of demand and continues with the particular case of the price responsiveness of mineral demand and its nature in the short and long-runs. A brief look at the response of mineral demand to price changes for other products is also included. The chapter concludes with a discussion on the effect of aggregate income changes on mineral demand and its nature in the short and long-runs.

Jan 1, 1985

By Ivano Andreis, Georgios Kalamaras, Mario Liti, Sebastiano Pelizza, Filippo Avesani

"THE SS640 AGRIGENTO-CALTANISSETTA PROJECT The Caltanissetta tunnel is part of the works for the construction of the second 28km-long maxi section of the SS 640 motorway of Porto Empedocle, from km 44 to the junction of Imera in Sicilian hinterland. Amongst other major infrastructure works, the €740 million ANAS (Italian national roads and highway administration agency) project consists of four twin tube tunnels three of which are being excavated by conventional means. The longest tunnel, underpasses the Caltanissetta city and has a length of 3.9km under a maximum overburden of 120m. The JV consisting of CMC of Ravenna and TECNIS SpA won the design & built tender in 2010. Construction started in early spring 2012 following the approval of detailed design and later on the approval of design for construction. THE CALTANISSETTA TUNNEL The Design Phase Tender design and detailed design foresaw the construction of 13.4m excavation diameter tunnels that were to be enlarged in a second phase to create, every 600m, 50m-long tunnel sections for emergency parking. During the design for construction project phase the JV proposed to replace the 13.4m tunnel with a 15.08 excavation diameter that incorporated apart from the two 3.75m wide lanes a 3.25m wide continuous emergency lane. This significant tunnel section modification was associated with better road safety conditions, simpler and safer construction procedures, better statics for the tunnel section while in terms of overall cost the solutions were equivalent.Geologic context The tunnel is located in the middle of the geologically known Caltanissetta basin that is intersected by various tectonic structures. The geologic context for the tunnel scale, was defined in collaboration with the University of Catania in early project phases. For almost its entire length the tunnel is excavated in the Terravecchia formation that represents the lower part of the stratigraphic sequence that was formed in the Tortoniano period of Miocene. The quite complex geological model is also characterized by the presence of the so-called Trubi formation that consists of clay and marl clay. Almost 90% of the tunnel traverses formations that are quite similar in terms of excavation behavior. Exception to this are thrust zones and a calcareous stretch of the alignment. This last segment has a length of 200m and was identified since the very beginning as a tunneling challenge due to the combination of very poor geotechnical properties and an important water load."

Jan 1, 2016

By Stan Tang, Yiming Sun, S. Amir Reza Beyabanaki, N. Sathi Sathialingam

The Kurve mixed-use development project including a 22-story tower at 2801 Sunset Place was constructed on a site consisting of a roughly rectangular-shaped lot at the intersection of Wilshire Boulevard and Hoover Street in Los Angeles. Two Metro Red Line tunnels, with depths of approximately 30 feet and 58 feet, respectively, cross below the building at distances of approximately 1 foot to over 63 feet from the site. This paper presents numerical modeling performed to evaluate the ground and tunnel behavior in response to building construction. Results of geotechnical instrumentation and monitoring undertaken during the building construction are also discussed.

Jun 13, 2023

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By J. W. Merks

At mineral processing plants the accuracy and precision characteristics of assays in mill feed, tailings and concentrate largely determine the reliability of the metallurgical balance. The accuracy of measurements is ensured by selecting effective sampling methods and efficient sample preparation procedures, and by effecting each phase without introducing a systematic error while the precision of measurements is determined by the sampling regime. Sampling systems and components, sampling methods and regimes, and sample preparation procedures will be reviewed. Different techniques to determine variance components for sampling, preparation and analysis, and to detect systematic errors in assays at mineral processing plants, will be discussed.

Jan 1, 1986

By James H. Vignos

An optical instrument designed for the on-line measurement of the size distribution of coarse particles (3-500 mm) being transported on a conveyor belt is described. Included is a discussion of the measurement technique, as well as test data verifying the legitimacy of the basic sensing approach. Field data indicating the instrument&apos;s ability to make useful measurements in an industrial environment are also presented. Applications in the mining and mineral industry, for which this instrument was orginally developed, are outlined, with particular emphasis given to the areas of crushing and grinding control.

Jan 1, 1979

By Claude A. Chapallaz, Dominique L. Butty

Bauxite is derived by surficial weathering of aluminosilicate rock forming minerals under warm and humid climatic conditions. Variations in climate combined with base level changes promote cyclical, evolutionary weathering/concentration patterns, the residual products of which are closely controlled by biological activity. Rock decomposition results mainly from hydrolysis, chelation and solution, the effects being (a) removal of bases and silica in dilute solution, (b) depletion of iron in areas where low pH-Eh prevail and, (c) concentration through direct precipitation, or more generally via intermediate amorphous phases, of aluminium hydrates in variable associations with iron hydrates and clay minerals. Bauxites can be regarded as aluminous soils, and as such they result from cyclic or polygenetic pedogenesis. The ferralitic pedological evolution is essential for bauxite formation. Under some specific conditions, related to local climate and parent rock composition, the podsolic- or andosolic-type of pedogenesis is an effective precursor to bauxitization.

Jan 1, 1984

By M. Kavvadas

Geotechnical design using Factors of Safety recommended by Codes of Practice is based on largely unknown ?margins of safety?, usually without consideration for the importance of the project (i.e., potential consequences of failure) directly or explicitly. On the contrary, probabilistic modelling can be a useful tool in risk management as it provides the means to measure the risk to be managed. This is achieved by calculating the probability of failure associated with a specific design, i.e., by relating the classical factors of safety with the corresponding probability of failure and by using a cost optimization procedure to achieve ?optimal? designs, accounting for the expected costs in case of catastrophic failure. This paper describes the methods used to calculate the probability of failure and its correlation with the classical Factor of Safety using sampling techniques and a simplified method based on the moments of the factor of safety considered as a random variable. These procedures are illustrated in an example which investigates the stability of a slope.

Jan 1, 2005

By Francis F. Pitard

The presence of elements, minerals, or chemical compounds in materials at very low concentrations is becoming a constantly increasing concern for several segments of the Industry. Some trace elements or chemical compounds may be considered as hazardous, some are simply considered as undesirable In complex processes where they could be constantly recycled and end up as the major factor of decreasing quality for some valuable products. In some other cases, the presence of a trace element or mineral may be highly desirable because of its economical value: precious metals are falling into this category, they probably were the first trace elements to draw our attention. Tremendous quantity of money is spent for analysis at the trace level, also the analytical "tool" has been considerably improved during recent years, but still the sampling aspect of the problem remains obscur for many, and because of it, large quantity of analytical efforts become meaningless. Not only the absence of sampling strategies is badly affecting the representativeness of a large majority of samples, but furthermore for the same reasons, many laboratories are failing In their endeavor to prepare reliable standard reference materials. The reason of this failure has its roots in the unability to estimate effectively the sampling characteristics of the element, mineral, or compound of interest, not to mention the unability to perform precise and accurate complete analysis, so essential for the instrumental analyst (1). In this paper a strategy to perform a better sampling operation is recommended. SELECTION OF A PROBABILISTIC APPROACH AS SOON AS PRACTICALLY POSSIBLE It Is essential to differentiate probabilistic sampling from non-probabilistic sampling. As Illustrated in Figure 1, the sampling operation Is a selection process which could be performed In two different ways: I. A probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with a same probability of being selected. 2. A non-probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with different probabilities of being selected.

Jan 1, 1986

By L. Lichty, R Bhappu, R. Rowan, G. Ramadorai

Treatment of refractory gold ores containing arsenic have always presented a major problem in their processing to recover the contained precious metal values. The major difficulties are concerned with lower recoveries, production of hazardous fumes, effluents and residues. Because of&apos;these arsenic related problems, many otherwise economically attractive precious metal deposits and dumps all over the world are not exploited. In recent years, treatment processee for refractory gold ores and concentrates have been explored and a few commercial operations employing roasting or pressure leaching have resulted. Roasting has limitations due to environmental constraints related to off gases. Pressure leaching involving high temperatures (180% to 200%) and pressures (400 psi) is accompanied by high capital and operating costs. An alternate route to roasting for treating pyrite and arsenopyrite ores and concentrates ia the "lime-oxygen hydromet" process carried out at a moderate temperature (100%) and pressure (100 psi). A simplified process for treating such arsenic containing ores and concentrates utilizing low temperature and pressure oxidation is presented. This low cost treatment with compressed air and lime renders arsenic as an inert component in the residue, meeting all the requirements of the EPA Toxicity Test. The precious metal values are then extracted from the autoclaved residue by standard cyanidation. This paper discusses this new development.

Jan 1, 1990