Search Documents

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By Celeste Powell

Liquid carbon dioxide can be used as a replacement for organic solvents in the extraction of anionic PGM complexes from an aqueous phase. This can be achieved only if highly carbon dioxide-soluble chelating agents are developed because conventional chelating agent-metal complexes, such as trioctylamine-gold chloride, are not soluble in liquid carbon dioxide (although trioctylamine is CO,-soluble). Our novel CO,-soluble chelating agents have a fluorinated tail and a conventional amine head group. Both the chelating agent and the chelating agent-metal complex are soluble at ambient temperature at pressures between 7-35 MPa. Equilibrium constants in the 105 range have been measured (in Freon 113, a low pressure screening liquid for carbon dioxide), indicating that these compounds will strongly bind the metal chloride. For example, 93% of Pt-chloride was extracted into Freon 113 using a 3.5:1I ratio of a double-tailed fluoroalkyl amine chelating:metal chloride. 88% recovery of Pt-chloride into liquid carbon dioxide was achieved using the same chelating agent at a 3.5:1 ratio.

Jan 1, 1999

By T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force. Pv, horizontal force, Ph, and longitudinal force, P1. A method for estimation of these forces is proposed, which relates their value to the properties of the conveyor structure and rails, shifting operation parameters, and other site-specific conditions. The effect of this force on shifter behaviour is analysed and guidelines are developed for selection of a suitable shifter. Also discussed are the requirements of the shifting operation for other equipment.

Jan 1, 1986

By M.P. ROY, ASHISH K. VISHWAKARMA, A.K. MISHRA, P.K. SINGH, VIVEK K. HIMANSHU

Principal component analysis (PCA) is one of the dimension reduction techniques widely used to classify data based on features. Ground vibration is a major hazard arising from rock blasting operations, and accurate prediction of the vibration is necessary for designing controlled blasting parameters. Most of the widely accepted predictors of ground vibration consider the maximum explosive charge weight per delay (MCPD) and distance as the parameters responsible for ground vibration, but mining sites with bigger production targets have varying geometrical parameters to suit the excavator utility. Accordingly, other blast design parameters will also have impacts on ground-vibration intensity. A blast vibration predictor considering all the blast design parameters would be complicated, and some of the parameters will have overlapping contributions to ground-vibration intensity. Data classification using PCA is a feasible solution, and regression analysis may be performed to develop predictors using the classified input data. In this study, PCA was used along with multivariate logarithmic regression to predict ground vibration, and the performance of this technique to predict ground vibration was compared with the performances of various existing empirical predictors. The evaluation suggests that the predictor with logarithmic regression followed by PCA performs better than the existing empirical predictors.

Nov 1, 2022

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010

By Roberto Carranza

The planning of experiments and the importance of statistical interpretation of the results have been recognized for years by scientists and engineers. The Factorial Design of experiments is among the various methods used for this purpose and is being widely applied in all branches of research and production. The basic principles of this tool have been described in detail (1, 2, 3, 4) and several examples of its application in various fields have been published (5). In recent years the mineral industry has also used Factorial Design to improve the efficiency of research, testwork and plant operation (6, 7, 8, 9). This method permits for a qualitative determination of the influence of the variables studied in a process and also a qualitative measure of the interaction of the variables. By graphic means or derivative methods, one may also establish the optimum conditions of the process (ibid 7, 8, 9). It is desirable, however, to develop mathematical methods to evaluate quantitatively these effects and restrict the optimization to the practical limitations of the variables. It is also convenient to adopt a notation system to generalize the Factorial Design.

Jan 1, 1971

By A. K. Clarke

In any treatment process that requires a coarse feed material to be reduced to a fine size by crushing and/or grinding it must be determined whether a wet or dry comminution system should be utilized. All factors must be evaluated in reaching the decision. Among these factors are: 1) Ecology and Plant Environment: Unfortunately in many instances the decision on wet or dry is based on prejudice resulting from an unnecessary fear of dust. The writers submit that this fear, although once justified, is no longer valid because technology and equipment is now available to collect dust to meet any standard. When dry grinding is used it is very often possible to discard a portion of the waste product in a dry state. This will decrease the size of the tailing pond required. As pollution control standards increase it becomes increasingly difficult to clean up water from tailing ponds. 2) Operating Costs: Steel wear is often five or more times greater in wet grinding than in dry grinding. This is mainly due to corrosion. The evaluation of the economics of dry grinding must of course include the air system and dust collection; similarly in a wet grinding plant related pumping and material handling costs should be included. Pumping costs are often overlooked. This assumes water is made to flow for nothing. Pumping can account for 20 percent of the power consumption in the grinding plant. Large scale comparative tests were conducted in a wet and dry commercial plant in 1970. The same ore was used for both tests. With all factors included in both plants the dry system showed lower horsepower per ton.

Jan 1, 1971

By J. Snowberger III

Rhenium is a valuable and extremely rare chemical element with unique chemical properties. It is extracted commercially as a byproduct from the processing of molybdenite associated with porphyry copper ores. There is a present interest in recovering rhenium from copper pregnant leach solutions (PLS) produced by copper heap and stockpile leaching. These solutions contain rhenium at very dilute concentrations, typically in the 1 mg/L concentration range. This paper describes laboratory column ion exchange experiments to extract rhenium from these solutions using weakly basic anion exchange resins and actual plant PLS from two operating mines. The dynamic loading and elution behavior of Re on Purolite® A170 and A172 is discussed.

Feb 23, 2014

By M. D. Monroe

Getting the best match between truck and haul road requires examination of many factors and their effect on the bottom line. Most mines use a bottom line measure based in some way on cost per ton of material moved. This measure focuses on the two components of truck haulage cost per ton: productivity (or performance) and operating cost. Productivity can be measured or predicted for specific tasks using either field measurement or modelling. Individual tasks can be combined to provide a larger scale, longer term net figure for total mine output. True cost is more difficult to capture as they are time and task oriented and can be influenced by a summation of factors over a truck lifetime. For example, "allocated" costs, such as owning (depreciation) and some repair costs, are spread over long periods of time. Other cost, such as fuel and tires can be tied more directly to certain tasks such as fuel and tire cost. This paper focuses on the more direct, task-oriented factors that affect truck productivity and cost.

Jan 1, 1992

By C. Manea

During exploration and exploitation of complex ores, waste dumps that contaminate severely the environment and in particular soils, are genetated. The most hazardous pollutants are heavy metals and metalloids (e.g As, Mo, Pb and Cu) as well as radionuclides (e.g U and Ra). Ecological remediation aims, among others, at decontamination of soils by preserving important properties as soil fertility.

Jan 1, 2008

Western Energy Co.'s Rosebud mine in Colstrip, MT, has implemented innovative mining techniques in the past,* and following in that tradition, new techniques for overburden removal were recently introduced at the Montana coal mine. In April 1979, falling coal production left Western Energy in a bind. At that time the company was one of the first to implement a dozer/scraper stripping system for additional stripping capacity. This time around, however, the challenge was to eliminate spoil rehandle with a dragline while digging down 33 in. "Rehandle will increase 20% by going down an additional 3 m past the 24-m level," according to Bob Cope, mine supervisor for Western Energy. To cut this additional expense by eliminating the need to rehandle, Western now uses scrapers to bench down for the dragline. This system utilizes the flexibility of scrapers as earthmoving tools. Although scrapers were originally purchased to fill an immediate need for productive, low-cost overburden stripping, they are now benching and continue to optimize the overall effectiveness of existing draglines. According to the company, the draglines couldn't keep up with production requirements if they had to rehandle spoil material. Benching with the scrapers eliminates spoil rehandle. Western Energy expects to produce 10.6 Mt of coal this year from three active pits in the Rosebud mine. Western estimates that there are enough coal reserves at Rosebud to support a 40-50 year operation. The sub-biturninous coal has an energy value of 9.2-9.4 Mj, 0.87% sulfur, 8% ash, and 20% moisture. Pit A, approximately 610 m long and 45-55 m wide, is the mine's greatest producer. A Marion 8050 dragline with a 46-ms bucket digs 30-33 m to uncover the 7.3-m Rosebud coal seam. Here, the scrapers were put to work benching for the dragline. Long Construction Co., which operates the mine equipment for Western Energy, uses four Caterpillar 637 tandem-powered scrapers, two Cat 631s and two Terex TS-24s. The number and combination of scrapers actually used for benching periodically changes, depending on which ones are needed for topsoil removal and reclamation. Scrapers benched down about 9 m and removed nearly 2.3 Mm of over-burden at pit A. About 1 Mm was placed in a 9-m lift on top of the high-wall at the head of the pit. The scrapers built up one side of the lift first and then the other on successive passes to

Jan 2, 1981

By David M. Sullivan

Jim Walter Resources, Inc., (JWR) a division of Jim Walter Corporation, has 5 underground coal mines in Central Alabama varying in depths from 400-2500 feet. Gas Chromatography plays a vital role in safety and production at each mine. Chromatographic data is used to monitor working areas for safety and proper ventilation and to control the quality of extracted methane for sales purposes. Instruments have a1 so been employed during mine rescue operations. JWR's first Gas Chromatograph (GC) was installed in April 1984 to monitor gob gas taken from longwall gob areas and sold based upon BTU value. The GC allows maximum extraction rate of the gas within the quality guidelines. By late 1985, another system was purchased and both units were upgraded to perform an analysis of indicator gases which may appear during mine emergencies. Each unit has the ability to detect and measure the following gases at almost any level ; Oxygen (021, Nitrogen (N2), Methane (CH4), Carbon Dioxide (C02), Hydrogen (HZ), Carbon Monoxide (CO) , Ethylene (C2H4), Ethane (C2H61, Acetylene (C2H2) and a composite of hydrocarbon threes and above (C3+). The analytical run is accomplished in less than ten minutes and is completely automated. This report will introduce Gas Chromatography as applied by Jim Walter Resources for the analysis of underground mine air.

Jan 1, 1987

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By LaPoint D. J.

Copper deposits in sandstones are excellent targets for open pit mines using SX-EW extraction and processing methods. The mineralogy consists of chalcocite as the primary sulfide and copper carbonates and sulfates in the zone of oxidation. Two general deposit types are recognized: early diagenetic copper deposits that are associated with the reddening of the surrounding sediments, and epigenetic deposits that are associated with the migration of copper-rich basinal fluids along faults into permeable reservoir beds with a source of reductant. Epigenetic copper deposits are more likely to contain enough tonnage to be economic.

Jan 1, 1996

By P. D. Rao

Chemical and physical properties of typical low-rank coal (LRC) ash are significantly different than bituminous coal ash. With the exception of extraneous ash, which is incorporated during mining or is due to ash partings within or between coal seams, LRC ash consists primarily of inherent ash that is bonded into the coal's organic matrix or finely disseminated mineral matter. This paper reviews the nature of LRC ash, both inherent and extraneous, and how this impacts the prospects of washing and utilizing LRCs. A literature review, as well as washability data, proximate and ultimate analyses and ash analysis of 25 Alaskan LRC seams are used as a basis for this discussion. The authors' recent research into the nature and distribution of phosphorous in an Alaskan LRC is also discussed

Jan 1, 1997

By Nathaniel White, Todd Kilduff, Justin Laviolette, Dan Laviolette, Randy Zeigler, Sean Sundermann

The Mitchell Point tunnel is a part of several ongoing efforts to connect the 12-mile-long Historic Columbia River trail between Mitchell Point Outlook to Mitchell Point Drive. The tunnel lies inside the Mitchell Spur entablature basalt geologic feature, extending 647 linear feet utilizing a typical horseshoe section with a height of 14.5 feet. The Oregon Department of Transportation (ODOT) required proper vibration control to minimize potential impacts to Interstate 84 and Union Pacific rail immediately below the tunnel excavations and sensitive, rare plants. The method of designing the vibration monitoring program and the results of its implementation show the iterative process of using monitoring to improve blast design as excavation proceeds, such as reducing air overpressure and COVID-related supply chain-constraints.

Dec 1, 2022

By Remi Tremblay

This paper describes the laboratory study which permitted an exploration of high grinding ball consumption in the secondary open circuit wet grinding mills at the Sidbec-Normines plant, Port Cartier, Québec. Corrosion undoubtedly exists but is of minor importance. Abrasion resulting from the physical nature of the company's iron concentrate is the main reason for the high ball wear. It was found that at least 30% reduction in ball consumption is possible by decreasing attrition grinding through the use of lifters in the mill. At the industrial level this would entail more lifters and/or higher lifters in the mill linings.

Jan 1, 1984

By R. T. Swindeman

"INTRODUCTION This paper will discuss the topics in the recently released Conveyor Equipment Manufacturers Association’s (CEMA) Belt Conveyors for Bulk Materials, 7th edition, that deal with safety and maintenance. The most effective way to improve conveyor safety is through designing out hazards in the earliest stages of a project. When the safest way to perform maintenance is also the easiest, mechanics will naturally take the obvious and least hazardous approach. IMPORTANCE OF ACCESS Studies have shown that mechanics spend almost one-third of their time accessing the components to be serviced and approximately 25% of all fatal conveyor accidents occur during maintenance1. Chapter 2 of Belt Conveyors for Bulk Materials deals with design considerations. In Chapter 2 there are recommendations for access at the various sections of a typical conveyor for cleaning, inspection and maintenance. While, in some cases, providing access will increase the cost of the conveyor system there can be significant paybacks in reduced injuries, faster maintenance and easier cleaning. Piping and Conduit One of the significant recommendations in Chapter 2 for access is to restrict the mounting of piping and conduit to the conveyor structure in the Loading and Discharge zones of a conveyor. Piping and conduit are more permanent fixtures than maintainable components and should be located out of the way of components needing frequent maintenance. If electricians and pipe fitters are given convenient locations to make their runs they will natural use them. Flexible conduit and hoses can be used to connect to components from pipe racks and cable trays which further enhances maintenance. Access for Cleaning Another critical aspect of access is for cleaning. Approximately 33% of all fatal conveyor accidents occur while cleaning spillage and carryback under and around conveyors2. In the loading zone having sufficient height under the conveyor for cleaning increases the cleaning interval and allows for safer cleaning. In the discharge zone having adequate access for belt cleaning installation has a direct effect on the ability to install a proper cleaning system and perform maintenance."

Jan 1, 2015

By Paul D. Tomlingson

Part one of this two-part series covers conceptualizing and developing a maintenance information system. It explains what information is necessary to manage such a system. Next month, part two will discuss using this type of system with administrative information, including error and absentee reports as well as open work files. Introduction There is no doubt that quality, timely, and accurate information can make a solid contribution to maintenance cost reduction objectives. Yet, despite obvious benefits, methods being used to acquire information systems are proving costly, frustrating, and often unsuccessful. Those needing the information are disappointed. Mine managers, hoping to reduce costs with quality information, are instead seeing no system, no savings, and massive spending on information endeavors of questionable benefit. Options Any software vendor will happily sell you his program. Numerous mining organizations, having "gone to the cleaners" themselves, will gladly make their programs available to help cover huge trial and error development costs. Any package can only be a generalization. Any program bought from some other organization must undergo numerous modifications to make it work properly. In the process the initial cost is doubled. Many mining maintenance organizations do not know how to go about the task of conceptualizing, developing, installing, and effectively using a maintenance management information system. Consequently, many have hedged their primary responsibility of specifying what information they want, how they will get it, and how they will use it effectively. Into this void have jumped many who claim they can help. But some may not understand the special information needs of maintenance in the mining industry. By default, the whole scene of maintenance information systems has become confused and in need of clarification. A Starting Point Four broad phases are used to organize the steps by which maintenance acquires an effective maintenance management information system and initiates its use. Conceptualization is an identification of needs, factors that influence development, and an assessment of support for the system. Development is a plan of action for bringing the conceptualized information system to life. Consideration is given to the practical aspects of collecting field data, processing it, and converting it into useful information. Implementation consists of those actions by which the newly developed system is integrated into the organization and put in the hands of its personnel so that its value can be derived. Use addresses the means by which personnel use the information to accomplish maintenance improvement objectives. These phases are preceded by establishing the need for the information system. They are followed by a requirement to measure its success (Fig. 1). Conceptualizing the Information System Responsibilities - The information system user must acquire the system best suited for its use. A step-by-step process is essential to avoid many serious problems than can easily occur. The most important step is to clearly identify its objectives and lay out a course of action to achieve those objectives. The major reason for the failure to achieve information objectives is not carrying out this responsibility. Maintenance cannot delegate the task to data processing. It can obtain technical assistance but it must retain responsibility. Nor can maintenance purchase

Jan 7, 1985