Search Documents

By R. F. Hadley

Alluvial valley floors constitute a valuable land resource and have been important to ranching operations in semiarid western United States. This resource may be in jeopardy locally if the alluvial deposits are disturbed by surface mining of coal deposits. Erosion problems caused by poor land-use practices can cause trenching of the unconsolidated alluvium with a consequent lowering of the water table and depletion of soil moisture needed to support vegetation. Historical evidence of this sequence of events is abundant in geologic literature and serves as the basis for assessing potential impacts of surface mining. The potential geomorphic impacts of surface mining on alluvial valley floors with regard to fluvial processes are: (1) disruption of the longitudinal profile followed by valley trenching and high sediment yields downstream and (2) replacement of the excavated alluvium with unconsolidated material that does not have similar physical characteristics and may be susceptible to erosion. Mining may disrupt the existing hydrologic framework affecting streamflow, ground-water levels and water quality of both surface water and ground water. Although functional hydrologic and geomorphic processes are similar, each valley represents a complex environment that does not submit to broad generalizations.

Jan 1, 1978

By P. M. Soupios

The study of soft soil (wastes above the rock bed) an issue of great importance in civil engineering, is usually addressed by drilling boreholes. This method is rather expensive and time-consuming and although the information obtained is usually accurate, on the other hand it is much localized. Recently published researches have demonstrated the ability of the combination of geophysical exploration methods to estimate the thickness of deposited wastes, which provides the layered structure of the study area and certain, method depended, mechanical parameters as well. By theory, the frequency of resonance of an upper layer is a function of its thickness and the average shear velocity in it. Furthermore, the application of H/V spectral ratios of micro-tremors is a fast, straight forward and cost effective methodology, yielding the determination of the main resonant frequency of the soil. Based on this framework, 20 microtremor measurements have been carried out in a Landfill in Heraklion-Crete. Some of these measurements were deliberately close to drilled sites, where the basement had been reached. Three electrical resistivity tomographies were also used, in order to define the landfill structure such as, thickness, determination of different wastes distribution in the study area and other parameters. In addition, estimation of predictive Vs using empirical relationship between shear velocity and penetration resistance (SPT?s) were also conducted. Knowing the thickness and the resonant frequency, we estimated the shear (Vs) velocity of the waste cover. The final Vs model was confirmed using the results from the Vs-SPT correlation. The combinative implementation of the above mentioned geophysical and geotechnical methods have successfully defined geometrical and geotechnical/geophysical characteristics of the area under investigation in a fast and cost effective way.

Jan 1, 2005

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By A. L. Mular

Introduction The cost of grinding may be divided into a fixed equipment cost portion and an operating cost portion. The fixed equipment cost is the amount of money required to purchase the grinding mill itself. This amount may be kept separate from the installation cost which, often, is taken as a percentage of the fixed equipment cost. A good average is 43%; therefore a $100,000 ball mill would cost approxi¬mately $143,000 installed. Operating costs are variable and paid per unit time for power, liner replacement, grinding charge replenishment, labor, and mainte¬nance including major parts replacement. Such costs depend on the geographical location and will vary with the cost of labor. Operating costs are difficult to estimate. Most mining companies consider such information proprietary. This section provides a means to obtain an estimate of the equip¬ment cost of a grinding mill with a rated accuracy of±l0%. Compara¬ble methods to determine operating costs are not available. Such costs are presented in table form with suggestions for updating them. Esti¬mating the cost of liners and steel replacement is possible as described in a later section. Capital Costs of Grinding Mills Grinding mill costs have been related,124 by means of equations and corresponding graphs, to the nominal horsepower requirements of mills. All graphs are based on a Marshall and Stevens cost index for Mining and Milling of 300, where a cost index is a ratio used to estimate current prices of equipment from obsolete prices. Where (Cost Index Now) Cost Now = (Cost Then) (Cost Index Then) (I) For example, the cost of an autogenous mill that requires a 3000¬hp motor is estimated as $500,000 (Fig. 95). This was the estimated price when the M&S (Marshall and Stevens, Mining and Milling) cost index had a value of 300. If the index is currently at 400, then the estimated current price of the autogenous mill is: Cost Now = ($500,000) (400) (300) = $667,000 Most professional journals will publish current values of cost indices at least once a month. In subsequent pages, each graph of grinding mill cost vs. mill horsepower has an associated graph of capacity vs. horsepower along with a table that relates mill size to horsepower. The associated graph and the table must be used with caution, since both apply to an average ore under average conditions. Example calculations showing how graphs should be used are shown in the following. It should be stressed that the cost data incorporated herein ex¬cludes the cost of pumps, motors, lines, and classifiers, unless other¬wise stated. Costs are not direct quotes; they are the averages of quotes supplied by manufacturers and analyzed by means of regression analysis. Example 1. Calculate the power required to grind 100 tons of dry solids per hour (in a closed circuit with a classifier) when the

Jan 1, 1985

By Babu R. Yama

Artificial Intelligence research has produced several tools for commercial application. Neural Networks, Fuzzy Logic and Expert Systems are some of the techniques that are widely used today. Artificial Neural Networks (ANNs) are excellent predictive, pattern recognition, and data analysis tools. In the mining industry, ANN techniques are being used commercially for real-time process control applications. Modeling of spatial data, ore reserve estimation, tunnel design, longwall stability prediction, and geologic roof classification are additional application areas in which neural networks have been applied successfully. A standard back-propagation algorithm was used to train a series of neural networks for a real-world predictive task. After training and optimizing the neural network architecture, performance of the network is measured on an independent validation set. Results indicate a correlation coefficient of up to 84 % between the actual and predicted values. A neural network model is developed for learning the spatial continuity of a mineral field and, consequently, for predicting sulfur values given coordinate values. The neural network performed not only satisfactorily, but in some cases performed better than the kriging model.

Jan 1, 1997

By R. G. Robins

The dissolution of metallic copper powder in aqueous solutions of cupric sulfate with ethylene under low pressure was investigated. The reaction stoichiometry obtained was:

Jan 1, 1988

By D. C. Shumway

Recently, the health of the cement industry has been threatened by the impact of environmental regulations, over-zealous state and federal agencies and radical environmental groups. Unfortunately, cement plant operations tend to trigger every environmental regulation and program promulgated, plus several programs designed specifically for the cement industry. These environmental burdens come at a time when the cement marketplace has been impacted by imports resulting in a situation where it has been difficult to increase prices to offset these increased environmental liabilities. The competitive world market forces the cement industry to seek creative ways to reduce costs. With additional major environmental programs coming down the pipe, like the Federal Clean Air Act Amendments of 1980 and EPA regulation of cement kiln dust, the cement industry has attempted to try innovative supplements to cement manufacturing. The cement industry has found that using waste tires, biosolids and other solid wastes in the cement manufacturing process can reduce costs and plant emissions.

Jan 1, 1996

By R. W. Macqueen

Organic matter commonly associated with Mississippi Valley-type (MVT) lead-zinc deposits may be used to assess the burial/thermal history of host rocks and sulfides. Organic matter may also have been involved in the genesis of H2S required to precipitate sulfide ores. Pine Point, Northwest Territories, Canada, provides an example. Located on the south shore of Great Slave Lake, Pine Point is an operating world class deposit which has produced 58 million tons of ore containing 3.0 percent Pb and 6.1 percent Zn from more than 40 Individual orebodies. Well-documented paleokarst features in a Middle Devonian carbonate complex are the main ore hosts. Sphalerite and galena ores are mainly open space fillings, and, from fluid inclusion studies, were deposited from saline fluids at temperatures of up to at least 100°C. Forms of organic matter occurring in the Pine Point barrier-reef complex Include indigenous organic matter, heavy oil and bitumen. Based on numerous geochemical criteria, it is clear that heavy oils and bitumens were derived locally from indigenous organic matter. The geochemical character of the Indigenous organic matter demonstrates that the barrier-reef complex is immature to marginally mature with respect to petroleum generation, and has not been heated above about 60°C maximum. Thus sphalerite with fluid inclusions that yield temperatures up to about 100°C represents former thermal anomalies. Bitumen is of two main forms at Pine Point: widespread soft, tarry material soluble in organic solvents (unaltered bitumen); and hard, brittle, glassy material that is mostly solvent-insoluble, and associated with white sparry dolomite and lead-zinc ores (altered bitumen). There are also partly altered bitumens. Unaltered bitumens have atomic H/C ratios of about 1.4, sulfur contents averaging 7.8 percent, and sulfur isotope ratios 634S) of approximately +4.6 per mil. Altered bitumens have atomic H/C ratios averaging 1.02, sulfur contents averaging 22 percent, and 634S values of about +12.9 per mil. These data and the organic geochemical character of a large suite of bitumen samples analyzed, strongly support the concept that some bitumen has been involved in the thermochemical reduction of sulfate to produce the H2S required to precipitate the ores. Mass-balance calculations indicate that the amount and degree of alteration of bitumen is more than enough to account for the reduced sulfur species deposited as metallic sulfides at Pine Point. MVT deposits, including Pine Point, seem to require the coincidence of available metallic Ions, pre-existing pore space, and a precipitating agent. A close look at organic matter in more MVT settings may outline trends in distribution or alteration which can be used as indicators of past thermal environments and processes of ore deposition.

Jan 1, 2013

By Donald L. Gaughenbaugh

Under the terms of the 1970 amendments to the Clean Air Act, the EPA established national ambient air quality standards for a number of pollutants. Sulfur dioxide (SO2) was one of these pollutants. These ambient air quality standards have had perhaps their biggest impact on the power utilities. In an effort to meet the air quality standards set forth by the EPA, utilities using high sulfur fuels have been forced to install flue gas desulfurization (FGD) systems. The majority of FGD systems in operation today are nonregenerable systems, that is the by-product of the system is disposed of, usually into settling ponds. Limestone slurry is the most common reagent used to remove SO from the flue gases. The calcium carbonate (limestone) slurry interacts with the flue gas, absorbing the SO2 and forming a by-product of calcium sulfate/sulfite which is disposed of.

Jan 1, 1986

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990

By George E. Aiken

Agglomeration developments in the iron ore industry of North America are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. These relationships have occurred mainly during the last 20 years. Many of these changes are an outgrowth of events which involved the history of the Mesabi Range. Although magnetic taconites had been discovered in the Lake Superior area about 1870, they remained unvrorked in part for lack of concentration methods and a generally unfavorable economic climate. Some 20 years later the rich Mesabi hematites were found beginning the era of direct shipping ores which continued through World War II. These Lake Superior iron ores included reserves of an estimated three billion tons. Following World War II, decreasing ore grades and rising costs began to force the closing of many underground iron mines. The early 50's saw the beginning of the decline in direct shipping ores and a spurt in produc- tion of natural iron concentrates. However, the market for unprocessed concentrates began to decline in the early 60's as agglomerated products and foreign ore s began to dominate the U. S. market.

Jan 1, 1973

By Rodolfo V. de la Cruz

The stresses in the materials surrounding an underground opening are dependent upon the virgin stress field, the geometry of the opening and changes in boundary conditions as mining progresses. For most underground openings especially in coal mines, roof bolts are installed to help stabilize the opening. While most parameters in roof bolt design and installation have been thoroughly investigated, the effects of the initial stress field on the effectiveness of roof bolts have not been recognized. This paper summarizes the results of investigation of the effect of the initial stress field on the performance of mine roof bolts. Roof bolt installations are duplicated in the laboratory utilizing conventional roof bolt frame, commercial roof bolts and shells, mine torque wrench and encapsulated rock specimens for anchorage. A special and primary feature of the laboratory set-up is the addition of a loading system for generating stresses at the anchorage specimens. For this preliminary study, different levels of hydrostatic stress fields were induced at the anchorage specimen, instrumented roof bolts were installed in the usual manner, and the bolt load loss-with-time observed. Statistical analysis of data showed that the stress field at the anchorage horizon has a considerable influence on the performance of mine roof bolts, i.e. the higher the stress field, the higher the anchorage efficiency. From this observation, methods of improving the performance of mine roof bolts utilizing new shell designs and methods of installing them are suggested.

Jan 1, 1978

By M. E. Gershon

Software for coal blending has gained a lot of recent attention as micro-computer programs have come on the market. Some of this software is appropriate and some is not. This paper looks at the types of models being used and points out the strengths and weaknesses of each. Recommendations are then made concerning the level of detail required for these programs, relating this concern to the various ways in which coal companies are using these programs. A checklist of company requirements for these programs and available pro-gram-features provides an aid in matching the program to the company.

Jan 1, 1988

By E. J. Berentsen

The Turquoise Ridge gold deposit is located near the Getchell Mine, 72 km (42 miles) northeast of Winnemucca, Nevada. The deposit is owned by First Miss Gold Inc. The host rocks consist of Ordovician and Cambrian age shales and limestones. They have been crosscut by the northeast-trending Turquoise Ridge shear zone and northwest-trending shear zones. Gold mineralization occurs at depths from 427 m (1 400 ft.) to 671 m (2 200 ft.), along the intersection of these structures. Large tonnage, flat-lying deposits occur where folded, favorable beds are intersected by the faults. The carbonate within the beds has been replaced with silica, pyrite and arsenic sulfides.

Jan 1, 1996

By B. E. Davis, D. A. Stanley, C. E. Jordan

A prototype expert advisor was developed by the U.S. Bureau of Mines to systematically offer advice on the control of a Florida phosphate operation. The PC based system receives input from remote sensors for circuit parameters such as feed rate, reagent addition, and pH and from operator entered information such as the quality of the concentrate and tailings in each of the coarse, fine, and amine flotation circuits. The computer evaluates the information using rules obtained from industry representatives and Bureau flotation experts. Recommended actions and questions are displayed to quickly guide the operator to a problem within the flotation circuit and suggest a solution. This process control system could provide more uniformity among the flotation operators and also serve as a trainer for new operators. In addition, it represents a step toward fully automated systems for phosphate flotation.

Jan 1, 1990

By Victor Despointes, Stephane Polycarpe, Kathryn Kelly, Chris Feeney, Brian Hann, Vojtech Ernst Gall

The Pawtucket Tunnel is a 2.2-mi, 30.2-ft diameter CSO storage tunnel in Rhode Island. The primary tunnel is built using a dual-mode open-EPB TBM capable of sealing the face within 120 seconds to manage poor ground and water ingress which is launched from within a SEM starter tunnel. The main tunnel connects to four adits along its alignment, three of which are SEM tunnels and one being a MTBM tunnel. This contribution describes the selection process, potential risks, and requirements for the TBM, as well as the design of the main tunnel, the adits, and the adit-bored tunnel connections.

Jun 13, 2023

By T. W. West

During the design and construction of a coal preparation facility, there are many items that can cause serious problems if not properly handled in the early stages of a project. These problems can be a detriment to smooth owner/ contractor relationships, the designing of a flow sheet, the selection of equipment, the design of the facility, the maintenance of schedule and budget, and a smooth start-up. It is the purpose of this presentation to identify some of these problems and to suggest steps that can be taken to reduce or eliminate their impact.

Jan 1, 1977

By Joseph Sopko, Xavier Lacourse-Dontigny

For the REM (Réseau Express Métropolitain) project, a 2500 m tunnel was built using a tunnel boring machine (TBM) under the Montreal Pierre Elliott Trudeau Airport (ADM). Although the geology under the Montreal Airport (ADM) would have been suitable for an excavation with a hard rock machine, the rst section reuired an earth pressure balance (EPB) TBM due to the soft soil located under wetlands. After excavating 280 m, the TBM was blocked in a transition zone of unconsolidated, water-bearing soils directly above the underlying bedrock. A free air intervention was not possible due to these geological conditions. After several failed attempts to create a slurry cake for hyperbaric interventions, a ground freezing system was designed and implemented, incorporating angled pipes drilled from outside the wetlands to directly in front of the cutterhead. This paper discusses the engineering reuired to form a frozen, water-tight zone in front of the cutterhead using liuid nitrogen. It also describes the complex method of replacing the disc cutters while holding the ground freezing system active in a manner protecting the health and safety of the workers.

Jun 23, 2024

By R. T. Hukki

The paper describes a two-stage industrial hydraulic classification system including hydrocyclones for primary classification and newly developed cone classifiers for secondary classification. Performance data based on large scale grinding and classification tests are presented.

Jan 1, 1981