Search Documents

By William D. Leech

Lebanon used a TBM for the firsttime to excavate a tunnel in the country. A main beam TBM, built in 1979, bored the 3.8 m (12.5-ft) diameter by 4,020 m (2.5-miles) Madiq Tunnel. The TBM bored through karstic terrain of dolomitic limestone, limestone and marly-limestone rock having near horizontal beds with more than twelve faults crossing the axis of the tunnel. The TBM also encountered more than six major karst features, filled with various combinations of boulders, clay, void space and water. The excavation through these collapsed-breccia zones drastically slowed the TBM?s progress. When complete, which the Madiq Tunnel is a part, the Kesrouane Water Project along the coast will bring fresh and irrigation waters to the parched and heavily populated region north of Beirut. The paper will describe the tunnel geologic features, karst genius, TBM upgrades and performance, and TBM/karst difficult situations

By K. Mondal

A macroscopic approach integrated with microscopic analyses for wettability characterization is presented. Wetting depends on 1) Contact between the dust and the fluid droplets, 2) Wettability of the particles by the wetting fluid, and 3) Wettability rate (due to low contact times). The goal of this paper is to show that the wetting rate is a significant factor in dust control. Samples from the roof, three different horizons of the coal seam and the floor were pulverized to less than 25 µm. Experiments were conducted with known wetting fluids to correlate surface tension and equilibrium wettability. Further analyses were performed in terms of surface charge (zeta potential), particle size, mineral composition, elemental composition, and quartz content. The surface tension reduction was also achieved by the use of chemicals and/or altering the temperature of the water. Two methods were used to evaluate wettability rates: a) near real-time comparison of wettability rates, and b) comprehensive evaluation of the intrinsic wettability rates. The data obtained provides meaningful insights towards the design of engineering controls for an economical solution to dust control in coal mines.

Jan 1, 2012

By Aki Fujii, Hiroshi Dobashi, Mitsuro Matsuda, Yoshinari Kondo

INTRODUCTION The Metropolitan Expressway Central Circular Route with a total length of approximately 47 km is located outside the Inner Circular Route of Tokyo (at a radius of approximately 8 km from the city center). Sections with a length of approximately26 km, slightly less than 60% of the total length, on the east and north sides are in ser-vice. Completing the Central Circular Route (Figure 1) is expected to enable through traffic concentrated at the city center to get around, and to form a well balanced trans-port network, which will alleviate traffic congestion considerably. The Central Circular Shinjuku Route, a section with a length of approximately 11 km on the west side, is now being constructed at a fast pace. The route is being built mainly by the shield tunneling method to carry out work smoothly under a trunk highway carrying heavy traffic and to reduce adverse effects of tunneling work on residents in the neighborhood. Shield tunnels have recently been becoming longer and deeper, and no secondary linings have been used in an increasing number of cases because of the over-crowding of cities or the reduction of budgets for public works. Economical, durable and high-quality segments have been required for linings of shield tunnels. Segments are made of concrete, steel, cast iron or combination thereof. Concrete segments are generally used in shield tunnels of medium to large diameter. Concrete segments are highly durable and resistant to compression, so they are highly resistant to earth pres-sure, water pressure and jack thrust. They are, however, heavy and have low tensile strength, so they are brittle and their corners are likely to spall. Concrete segments should therefore be handled carefully.[1] The authors have developed a steel fiber reinforced highly flowable concrete segment (referred as SFRC segment) that overcomes the weaknesses of concrete segments[2] to construct economical, durable and high-quality linings. SFRC segments have been applied to outbound sections SJ51 through SJ53 of the Central Circular Shinjuku Route. Unlike conventional concrete segments (referred as conventional RC segments), SFRC segments are made of steel fiber reinforced self-compacting highly flowable concrete. SFRC segments require less reinforcing bars than conventional RC segments because steel fibers are expected to work as reinforcements. Steel fiber reinforced concrete is a composite material that overcomes the brittleness of plain concrete, and has higher resistance to bending, tension and shear than

Jan 1, 2007

By Carlos Henrique Turolla Maia, Ulrich Maidl, Marc Comulada, Julio Claudio Di Dio Pierri

"Pure sands are typically the domain of slurry shields due to their high permeability and their granular characteristics. However, the Earth Pressure Balanced (EPB) shield machine technology has advanced in recent years with improved conditioning agents and shield machines that are equipped with slurry injection facilities and alternative mucking methods. These new so-called hybrid EPB machines have steadily increased the range of application of the EPB technology. The contribution discusses the capacities and operational features of hybrid EPB vs. slurry shield technology in pure sands. At the example of the Metro Line 4 in Rio de Janeiro (Brazil), the contribution shows that hybrid EPB tunneling in pure sands is possible and it is compared with a state-of-the-art slurry shield project as the KASIG project in Karlsruhe (Germany). Furthermore, the control of the support pressure by means of foam conditioning and slurry injection in conjunction with a close, real-time monitoring of machine parameters is discussed. INTRODUCTION Slurry shield and EPB technologies have both undergone significant developments in recent years, leading to the use of parts of one technology in the other and even to completely hybrid systems. Also the ranges of application (see recommendations by DAUB (DAUB 2010)) of both technologies have been shifted far beyond their original limits and are largely overlapping by now. Nevertheless, the basic principles of face support remain unchanged. Exploiting the possibilities of process data analysis (Maidl 2014), the interactions between the ground and the shield machine are a matter of research and have been intensely investigated. PRINCIPLES AND CALCULATION OF FACE SUPPORT PRESSURE Figure 1 shows the principles of two approaches for the determination of required support pressures: kinematic methods and numerical methods. Kinematic methods that are employed for the assessment of face stability only consider the situation in front of the TBM. The required face support force is determined by means of an assumed failure wedge that would form in ultimate limit state. Based on the ground properties, the vertical surcharge and the self-weight is transformed into a horizontal force along a virtual sliding surface. This horizontal force is to be balanced by the face support. The calculation results are amended by respective partial safety factors for water and earth pressure and the method-specific support pressure fluctuations are added."

Jan 1, 2016

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

Syncrude Canada produces a large part of Canada’s crude oil supply. The company processes about 225,000 bbl/day. The oil produced is used for jet and automobile fuel, home heating oil, plastics and other consumer synthetics. Crude oil is produced through a process of mining, extracting and upgrading bitumen. A rich supply of bitumen is contained in the Athabasca oil sands deposit in northern Alberta. Tailings from the bitumen processing are sent to a settling basin.

Jan 1, 2000

By R. N. Gow

The presence of enargite (Cu3AsS4) is problematic in gold processing because it is environmentally hazardous due to its arsenic content but also because it is double refractory causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte, Montana and Quiruvilca, Peru were spectroelectrochemically studied under alkaline conditions, pH range of 8-13, using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after voltammograms were potentially cycled in order to determine and compare surface species against theoretical EH-pH diagrams determined from mass-balanced thermodynamic calculations using StabCal software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of sulfur suggests that copper was eventually leached. By operating above pH 12, under slightly reducing conditions near -300mV vs SHE, arsenic can be selectively leached as thioarsenate (AsS43-) or thiosulfate (AsO43-) without sulfur formation.

Feb 27, 2013

By William Reininger

Microtunneling provides a necessary solution for multiple utility crossings associated with the New York Metropolitan Transportation Authority Capital Construction Company?s (MTACC) Eastside Access Project for the Long Island Rail Road. Construction of four TBM tunnels and their approach structures at the eastern end of the project in Sunnyside, Queens required significant modification and expansion of the railroad infrastructure at this location. Maintenance of railroad traffic during project construction is a principal requirement. As a consequence fourteen (14) utility crossing segments are being installed under active traffic by microtunneling methods. Microtunnels were installed in a variety of conditions including depths, types of soils and construction restraints.

By John E. Tilton

Real copper prices during the past several decades display two striking characteristics. First, they are highly volatile. Within a year or two, copper prices can rise or fall by 30% or more. Second, over the longer term, they are falling. Indeed, since 1970, the secular trend price for copper is down by more than 50%. Figure 1 highlights both of these characteristics. It shows the average annual US producer price for copper since 1970 measured in constant 2001 US dollars. While the London Metal Exchange (LME) copper price is not shown, it and the US producer price have for some time moved more or less together. So pronounced short-run fluctuations around a significant long-run decline describe copper prices, not only in the United States, but around the world.

Jan 1, 2002

By S. Schina

Part of the Imittos Western Peripheral Motorway in Athens is the twin road tunnel in the vicinity of American College, with 20m excavation diameter. In the paper, the environmental and other requirements, the geometry and the geological – geotechnical characteristics of the rock formations in the construction area are given. Information regarding the modeling and analysis methods that are used for the design of the temporary support, the final lining and the wedge and slope stability analysis is described thoroughly. Finally, the results of the analyses are compared with these of measurements and general remarks during the construction of the tunnels.

Jan 1, 2001

By Bruce Richardson

A contractor-manufactured 4.75m (15'-7") diameter EPB shield excavated a 115m (375 ft) long tunnel under the San Antonio River as part of the Salado Creek to Dos Rios Pipeline Interconnect Project in San Antonio, Texas. Lignite, limestone concretions, and sandstone in the face of the tunnel required the use of disc cutters. Less than 7.6m (25 ft) of sand and gravel hydraulically connected the top of the tunnel to the channel of the river. Fully lagged steel ribs with filter fabric were used for initial ground support and water control. This and other contractor manufactured TBMs in the 1.2 to 4.75m (4 to 16 ft) range are presented with descriptions of the jobsites, equipment, performances, and problems.

Jan 1, 2008

By F. Dahl, P. Raleigh, J. Holzhauser, B. Nilsen

Tunnel excavation using tunnel boring machines (TBMs), has become increasingly common in recent years, despite the fact that precise evaluation of certain risks have not kept pace with the use of these machines. One of the risks easily overlooked by Engineer and Contractor alike are the effects of abrasive ground on the costs and schedule of a given project. The impacts of worn and damaged TBM cutter heads have been observed on hundreds of tunnel projects around the world. It would appear that a reliable prognosis of the abrasiveness of soils on a project would be of great importance for designers, clients and contractors alike. Several well acknowledged test and prognosis methods already exist for rock, however there is only very limited knowledge available to describe the abrasiveness of soil and its impact on soft ground TBMs. This paper will examine approaches to this problem and suggest a new approach based on a current project undergoing design.

Jan 1, 2007

By Larry H. Heflin

The Washington Metropolitan Area Transit Authority's Wheaton Station and tunnel design was completed and offered for bid in the Spring of 1983. The format was unique to the Authority: a four part, four fiscal year contract developed in response to funding limitations with construction divided into four stages allowing the maximum amount of work to be done each year for the funds available. The bid was based on the entire contract, but was orginally awarded for only the first year's work. Each year's work had a maximum funding limitation thus safe guarding the Authority from a grossly unbalanced bid. The Authority's estimate for this work was $83,871,524. The low bid came in at 61% of this for a total low bid of $51,512,058. The low bidder was ILBAU America Corporation whose home offices are in Austria. Following receipt of the bids (and resolution of objections cited by other bidders who felt that the job could not be done for the $51 Million dollar figure), a Notice-To-Proceed was given on October 5, 1983. The construction contract allows a Value Engineering Change Proposal, called a VECP which is initiated and developed by the contractor to change the drawings, specifications or other requirements of the contract. Among other things the VECP should decrease the contract price while maintaining the service life, reliability, ease of maintenance, and standardized features and appearance and not require an unacceptable extension of the contract time. A VECP must estimate the amount of the net savings

Jan 1, 1985

A dedicated tunnel construction version of the Caterpillar 328D LCR compact radius excavator is proving highly productive on the A9 Autoroute construction project near Visp, in Switzerland. It is the first machine of its kind to operate on a Swiss contract and uses a special dedicated front attachment designed and constructed by German Caterpillar dealer Zeppelin. The machine offers a powerful, stable and compact solution for tunneling contractors. A rear overhang of just 305 mm (12 in.) provides a tail swing radius of just 1.9 m (6.2 ft). The 328D LCR is ideal for the restricted working areas within a tunnel construction site. The machine is equipped with the wide tracks from the 330D L conventional crawler excavator, ensuring maximum stability when operating. In addition, the boom mounting has been moved further toward the center of the machine for the tunnel model, creating an increased lift capacity over the front end compared with a standard 325D L. The boom itself features a robust box section construction, with high-strength steels, additional supporting struts and reinforced bearings for maximum durability. All pins have hard-chromium plating for optimum protection against wear. Stick digging force is a powerful 134 kN, with up to 212 kN of bucket digging force available, for maximum penetration in blasted material. The 328D LCR is also equipped with a heavy-duty dozer blade as standard. This ensures outstanding stability when working and providing a useful secondary tool for clearing and leveling within the jobsite. Two 45° tilting mechanisms in the boom construction, allow the boom to be swung to 45° on either side of the machine. So the specially designed attachment linkage provides increased rollback for access to the roof of the tunnel. A Caterpillar CW45S mechanical quick-coupler allows rapid changes between specialist tunneling attachments, standard Caterpillar buckets and a range of Caterpillar work tools. The machine is powered by a Caterpillar C7 diesel engine. This six-cylinder EU Stage IIIA diesel motor [ ] offers 8 percent more power than its predecessor, with 140 kW (190 hp) available at just 1,800 rpm. Caterpillar?s ACERT combustion technology results in lower fuel consumption and reduced exhaust emissions. However, the tunnel machine is also equipped with a diesel particulate filter as standard, to further cut exhaust gases within the tunnel working. The 328D LCR is designed for use in transport tunnels of 6.8 m (22.3 ft) in height. With the tunneling boom in place, the machine has an operating weight of 42,540 kg (93,783 lbs), yet retains a transport height with the tunnel boom of just 3.9 m (12.8 ft). Transport width with 600 mm (23.6 in.) track shoes, is just 3.2 m (10.5 ft). On the A9 tunnel contract, the machine is being used by a consortium of Swiss and Austrian companies working for the canton of Valais? Routes Nationals Construction (RNC) department. The 31.8-km (19.7-mile) A9 Autoroute construction project will connect Sierre in the west and the town of Brig to the east. The tunnel that is bypassing the town of Visp is just one of a number along the mountainous route.

Jan 1, 2009

By G. Tiravanti

A recurrent concern in mining operations is how to deal with the large volumes of fresh water used which in turn generates large volumes of effluents that have to be treated. Water treatment can focus in one of two main strategies: treat the effluent as it is produced, or use a simulation tool to optimize water use in the process and reduce volume of effluents, contaminants concentrations, operational costs, and so on. This article shows a successful tool developed in Matlab-Simulink® that allows modelling a mining process and simulating potential improvements to evaluate the results. This tool has been proven in Cu-Mo operations and recently it has been used in poly-metallic operations. This article reviews the 4 Key Steps required to achieve our goals: a) Elaboration and verification of the mining Operation?s Block Diagram, based on a field survey; b)Model construction and input flows and qualities in selected streams; c)Model Validation and Simulation of new alternatives like recirculation, changes in reagents and dosage, partial treatment, flows merges/separation, and others; d)Development of the Optimal Solution which consists on determining the CAPEX and OPEX.

Feb 27, 2013

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By G. L. Dollinger, J. P. Kindsvater, J. A. Gibson

DESIGN AND DEVELOPMENT OF A MOBILE MINING MACHINE INTRODUCTION Until recently, developing tunnels in hard rock has been accomplished either by the drill and blast method or by using large tunnel boring machines. Combining the flexibility of drill and blast with the safety, efficiency and productivity of a TBM has been the objective of mining machinery producers for many years. In 1979 The Robbins Company began developing a new type of tunnel boring machine called the Mobile Miner to meet these objectives. The development and testing of the Mobile Miner is the subject of this paper. CURRENT MINE DEVELOPMENT METHODS Both the drill and blast method and the use of a TBM have notable advantages and disadvantages. The drill and blast method, for example, allows much more flexibility, requires less setup time and has a lower initial cost than a TBM; however it requires the use of high explosives and blasting has a disrupting effect on the rock surrounding the development. A TBM, on the other hand, is safer to operate, more efficient, more productive and produces smooth tunnel walls without disturbing the surrounding rock. In longer straight drifts it will easily out distance the drill and blast method. The TBM, however, is limited to boring a circular cross section tunnel which must then be modified if a flat floor is required. It also has a higher initial cost and an extended setup period.

Jan 1, 1985

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

By R. Strandahl

As one of the largest private utilities globally, E.ON currently operates hard coal fired power stations in with a total installed capacity of some 20.000 MW: These thermal power plants consume domestic coals but are increasingly dependent on imported seaborne traded coal (in 2009 approx. 17 million t). Knowing that the company’s reputation and credibility depends in part on how E.ON lives up to the responsibilities along the entire energy value chain, E.ON takes a collaborative approach with the various suppliers. Hence, E.ON’s responsible policy also applies to the procurement of coal; the utility launched in 2009 a comprehensive Corporate Responsibility program with special focus on supply-chain audits. One of the first coal audits focussed on the Cerrejón coal mine in North Eastern Colombia. The authors will share the key learning’s and experience from the Colombian audit jointly conducted with an independent auditor and E.ON experts from the Corporate CR and E.ON Energy Trading.

Jan 1, 2011