Search Documents

By Andrew B. Pervis

With the ever increasing demand for Finer powders by industry there has been a continuing effort by air classifier manufacturers to improve and offer machinery capable of producing these fine powders. Common to these classifiers is the use of a multivaned rotor through which passes all of the air used to transport the particles to be classified. Rotor revolutions per minute and the amount of air passing through the rotor are the main variables in determining the particle sizes which will be able to pass through the spinning rotor. A simplified equation derived by setting the air drag force carrying a particle through the rotor equal to the centrifugal force due to the spinning rotor's action on the entering air and particle is: Diameter of Particle = [ ] Where K is a function of air viscosity, particle configuration, rotor and blade configuration; RPM is rotor revolutions per minute; M3/sec. is air quantity passing through the openings between the rotor blades.

Jan 1, 1983

By Jung-Joo Kim, Jong-Uk Kim, Turab H. Jafri, Han-Kyu Yoo

"INTRODUCTION Steel sets such as H-type and lattice girders are often installed in the tunnels before the hardening of shotcrete to ensure the stability of conventional tunnels in soft ground conditions. In practice, while designing the tunnels with the help of numerical analysis, steel sets are generally considered only as temporary support elements. Only a few studies propose the direct application of composite support in the tunnel design, based on large-scale experiments and numerical analysis. In order to assess the structural performance of the composite support consisting of shotcrete and steel sets, large-scale experiments were performed on two types of arch-shaped specimens by applying the combined effects of axial forces and bending moments. Based on the experimental results, numerical analysis was performed to assess the application of composite support in tunnel design. The crown settlement, axial forces, bending moments, and load distribution in the composite support were analyzed in the light of different structural patterns. LARGE-SCALE EXPERIMENTS USING COMPOSITE SUPPORT Preparation and Procedure of the Experiments The preparation setup as well as the organized procedure of the large-scale experiments using composite support is shown in Figure 1. An appropriate geometry of the specimens was selected by considering the standard cross-section of a two-lane highway tunnel in South Korea. Under the loading conditions meant to develop the axial forces and bending moments simultaneously, arch-shaped specimens were assembled with the ends of the specimens subtending a 60° arc angle at the center of the arc circle as shown in Figure 2. The fabrication of six specimens was completed in two groups based on the dimensions of steel sets, with the first group of three specimens being reinforced by H100 (No.1, No.2, No.3) and the other three by H125 (No.4, No.5, No.6). In order to reduce the voids on the boundary of the shotcrete and steel sets, concrete was casted over the steel sets instead of using shotcrete. The specimens were designed to incorporate the uniaxial compressive strength of 21 MPa. Shear keys and steel plates were installed at the ends of the specimens, so that shear failure could be avoided at the ends and the specimens could also be protected from detachment at the fixation. Translational and rotational movements at the ends of specimens were fixed."

Jan 1, 2016

By Verya Nasri, Agustin Rey

Once completed, the Montreal Réseau Express Métropolitain (REM) will be the fourth largest automated transportation system in the world. The REM represents construction costs of approximately 7.0 billion Canadian dollars. The project consists of 67 km of twin tracks over four branches connected to downtown Montreal. The project includes 26 stations with 3 underground stations in downtown Montreal. One of the underground stations was built using the NATM method with thin permanent shotcrete initial and final liners separated by a sprayed on waterproofing membrane. The 2 other underground stations were built with the cut and cover approach including one using permanent secant pile wall with permanent walers and struts as the support of excavation and the final perimeter wall of the station. The project also includes the rehabilitation and enlargement of the Mont Royal Tunnel. This 100-year-old double track tunnel is about 5 km long. The REM also consists of 3.6 km new TBM tunnel connecting downtown to the Montreal International Airport through saturated soft ground and karstic rock. By the time of RETC, the construction of REM underground structures will be completed. This paper presents the design and construction aspects of the underground structures of this mega project.

Jun 13, 2023

By Robert B. Scott

Acid mine drainage, discharging from coal beds, has polluted our streams and rivers since early time. These pollutants affect water quality by lowering the pH, reducing natural alkalinity, increasing total hardness, and adding undesirable amounts of iron, manganese, aluminum and sulfates, The tangible damages are the costs involved in replacing equipment corroded by the acid water, additional treatment costs at municipal and industrial water treatment plants, and damages resulting from corrosion of steel culverts, bridge piers, locks, boat hulls, steel barges, pumps, and condensers. Intangible damages, which are real and important, include destruction of biological life of the stream, reduced property values, and streams rendered undesirable for recreational uses.1 The major problems of mine drainage occur in the anthracite and bituminous coal regions in Appalachia. However, many of the western mining states have significant mine drainage problems in specific areas, but the overall problem is not as great as in the eastern states.

Jan 1, 1970

By P. J. Mackey

A whole new group of non-ferrous pyrometallurgical processes with the ability to utilize tonnage oxygen and capture sulphur dioxide were developed and commercialized over the period 1940s–1980s. Many of these earlier process developments were undertaken with limited knowledge of the process chemistry and influence of key process variables; in many cases, piloting helped provide much new physico-chemical data, but gaps remained. The second generation versions of these technologies of today provide all the primary copper, nickel and lead produced worldwide by pyro-metallurgical smelting. Further, process development has continued and a new generation of copper and lead smelting technologies have also been developed in China since the 1990s. The older reverberatory and blast furnaces have been progressively replaced by the newer technologies—a good example being the introduction in 1992 of the copper IsaSmelt technology at the Mt. Isa smelter in Australia where the former fluid bed roaster and reverberatory furnaces were replaced by a single new smelting unit, together with an acid plant for sulphur dioxide collection. The development of these new technologies was made possible by investment in fundamental and applied research. The lesson for the future is, in order to sustain these improvements, continued investment in research and development capability is required—to do otherwise is to risk obsolescence and lack of competiveness in the world market. Dr. Peter Hayes at The University of Queensland is one of the many researchers and process engineers who have contributed to the fundamental understanding of metallurgical processes over this period of rapid change in technologies. The present paper briefly outlines some of the many contributions Peter Hayes has made to the understanding of kinetics, mechanisms and phase equilibria in metallurgical systems, and metallurgical process development.

By R. H. Ring

The Automatic Extraction System (AES) was designed and built under a U.S. Department of Energy Contract by the National Mine Service Company in cooperation with the Lee Engineering Division of Consolidation Coal Company. The Pennsylvania State University, Mining Engineering Section, was contracted as an independent auditor of the AES performance. The AES had a rotating cutter drum like a continuous mining machine; but two hydraulically powered roof supports, four roof-bolting drills, a dust scrubber, a ventilation fan and ducting in the roof supports, semi-automatic control, an extensible chain conveyor, and other innovations led to the distinction "extraction system" as opposed to "miner-bolter" or "continuous mining" machine. After design and assembly, the AES was field tested experimentally in an underground coal mine. The in-mine performance audit was preceded by a computer simulation of the potential production for a later comparison with the actual tonnage mined by the AES. This paper describes the results of an in-mine trial and assesses the production potential of the AES.

Jan 1, 1980

By S. Dubnewych, S. Kieffer, M. T. McRae, R. R. Redd

The seismic vulnerability of the existing outlet tower at Lake Mathews reservoir, located in Riverside County, California, necessitated the design of a new outlet facility to assure serviceability of the facility following a major earthquake. The components of the proposed facility include: a new outlet tower; a shaft; a new outlet tunnel; an approach channel that will be excavated underwater; and two short tunnels that will connect the new outlet tunnel to the existing outlet tunnel via the shaft. As the new facilities will be constructed while the reservoir is in operation, a cofferdam will be constructed around the site of the new outlet tower. The design for the underground facilities used a combination of empirical methods; limit equilibrium analyses, including displacement-based pseudo-static analyses for dynamic loading conditions; and numerical analyses. This paper outlines the design methodology used to develop an innovative design for the facilities which can be constructed within the time frame required by the operational schedule of the reservoir and existing outlet facility.

Jan 1, 1999

By W. R. VanSlyke

Scrubbing is gaining increasing recognition as a valuable tool in the treatment of Mesabi Range intermediate iron ores. In general, the earliest washing plants included log-washers in their various flowsheets. While log-washers certainly did impart a degree of scrubbing to the crude ore, such treatment bears little resemblance to the type of scrubbing being practiced today. At the time that these early plants were erected, only the true wash-ores were being processd. ("Wash-ores" are defined as crude ores in which relatively coarse chunks of almost completely liberated iron are found in a matrix of loosely-consolidated fine sand.) To treat ores of this type, sizing at approximately 65 to 100 mesh was sufficient to produce a merchantable concentrate. As crudes were being treated in which there was little "locking" of iron and silica, log-washers tended to disappear and large screens and classifiers took their place in Mesabi range flowsheets. The "screening and classification" type of flowsheet 'had its greatest usage in the 1945-55 period, generally speaking. During this same period, many operators found it necessary to supplement the "wash-ore" type flowsheet with heavy-media treatment.

Jan 1, 1959

By Samuel S. Adams

The Grants uranium region of northwest New Mexico is the largest uranium district in the United States (approximately 50% of U.S. production plus reserves) and one of the largest In the world, with approximately 900 million pounds U308 production plus reserves. Deposits of the region are unusual among sandstone deposits for their high content of epigenetic carbonaceous material, generally interpreted but not proved to be of humic origin--that is, co-extensive with uranium in the primary deposits. Virtually all production in the region has been from the Jackpile Sandstone and Westwater Canyon Member of the Jurassic Morrison Formation. The tabular uranium deposits contain, in addition to humate and uranium, significant authigenic phyllosilicates, quartz overgrowths, humate-replaced detrital silicates, and a trace-metal assemblage typical of other sandstone uranium deposit types. Surrounding the deposits in the two sandstone units of the Morrison Formation is an alteration zone within which iron leaching has altered detrital ilmenite-magnetite to residual masses of titanium oxides. Feldspar alteration is locally present within this zone, below deposits in the Jackpile Sandstone, and above those in the Westwater Canyon Member. The feldspar alteration increases in inten¬sity toward the Brushy Basin Member which separates the two sandstone units, ranging from partial replacement to replacement and dissolution of plagioclase and sanidine. Spatial relations among the epigenetic humate, authigenic silicates, and the broad alteration zones that extend from the Brushy Basin Member to and including the uranium deposits suggest that (a) the organic material was involved in the unusual silicate alteration, transport, and authigenesis, and (b) that the humates originated in shales of the Brushy Basin Member. Stratigraphic relations among the Brushy Basin Member and the overlying Jackpile Sandstone and underlying Westwater Canyon Member suggest [in turn] that there was continuous, interfingering deposition controlled in part by contemporaneous basement subsidence along northwest- and northeast-trending zones. Following minor erosion of upper Jackpile Sandstone and deposition of basal organic-rich Cretaceous sediments, the silicates of the Jackpile Sandstone were once again altered by organic-bearing fluids, this time permeating down from Cretaceous sediments and partly obliterated ore-stage alteration.

Jan 1, 2013

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By R. L. Russell

Production at Freeport Indonesia's Ertsberg open pit copper/gold mine started in 1972 at a rate of 7500 t/d. Mill throughput remained at that rate for a number of years until the discovery of the Ertsberg East (GBT) orebody. This discovery prompted three successive expansion stages from 1981 to 1988 that boosted production to 20,000 t/d. The discovery of the huge Grasberg porphyry copper deposit in 1988 launched a new era of much larger expansions. The first of these involved installation of a fourth primary mill in 1989 to bring production up to 32,000 t/d and was immediately followed by an expansion of the crushing and screening plant and the addition of a new south concentrator to bring production to 57,000 t/d in 1991. The addition of a primary ball mill and the changeout of the original Denver flotation cells in 1993 has served to optimize current production at a level of 66,000 t/d. A major expansion is now in progress. This includes construction of another new concentrator to house a SAG mill circuit and large Wemco flotation cells in an area created by the removal of 6,000,000t of glacial material. This current expansion, with a planned completion in 1995, will take production to 115,000 t/d. This paper describes the evolution of the Freeport Indonesia (FI) concentrator to-date and will then go into an in-depth discussion of the 66,000 and 115,000 t/d expansions.

Jan 1, 1994

By Richard A. Thomas, III JAMES H. ROWLAND, Liming Yuan

This paper presents the results of large-scale fire experiments on evaluating the performances of carbon monoxide (CO) and smoke sensors at low ventilation velocities. Experiments using three different combustibles — conveyor belt, coal and diesel fuel — were conducted in the experimental mine at the U.S. National Institute for Occupational Safety and Health (NIOSH) Bruceton Research Facility. A total of eight sensor stations were located downstream of the fire with each station containing sensors for CO, smoke, carbon dioxide (CO2 ), oxygen (O2 ), humidity, barometric pressure and temperature, as well as two airflow sensors. The airflow velocity ranged from 0.22 to 0.26 m/s (44 to 51 fpm) in the tests. The response times were recorded for the CO and smoke sensors at each sensor station when smoke and gaseous products of combustion from each burning combustible reached the station. The response times of the CO sensors were used to determine the appropriate sensor spacing in the belt entry with a low air velocity. The performance of the smoke sensor was found to be affected by the high humidity in the experiments. The results on proper selection of sensors and the determination of sensor spacing at a low ventilation velocity can be helpful for ensuring sufficient early fire warning for underground workers, thereby improving the health and safety of miners.

By Robert L. Russell

The Bunker Hill Mine, located in the Coeur d'Alene Mining District at Kellogg, Idaho, has been a major producer of lead-silver-zinc ores since its discovery in 1887. The mine has produced over 29 million tons of ore from some 20 to 25 veins and ore zones, and now covers an area approximately one mile in length and one-half mile in width. The active section of the mine extends from 2500 ft above sea level to 1600 ft below sea level. Production is presently at the rate of about 1700 tons of ore per day. A two-mile adit, the Kellogg Tunnel, at the 2500 elevation, provides access to the main shaft area. Ore is hoisted to the adit level through a 5000-ft, 500-inclined shaft, extending to the lowermost haulage level 1200 ft below sea level. Primary shaft service for men and materials is supplied by three major internal, inclined shafts equipped with double-drum hoists. Present production requires ten levels to serve for mainline track haulage. These range up to 5000 ft in length and are either 200 or 400 vertical feet apart. Also, many intermediate levels exist throughout the mine. The conventional and autoloader mechanized square-set and cut-and-fill mining methods used throughout the mine have been the subject of a recent paper(l). One-third of current production is from vein-type ore bodies which are long distances from main shaft areas. Such veins generally dip about 450, have relatively narrow widths of from 3 to 20 ft, and usually contain less than 500,000 tons of ore. For many years, ore bodies thus situated have been developed by means of a separate inclined, timbered service shaft-raise connecting two or more main haulage levels. These commonly range from 400 to 1000 ft in vertical extent and are equipped with 25 to 50 hp electric, single-drum hoists. Intermediate levels are driven as conventional track drifts at 100-ft vertical intervals between the haulage levels. Ore and waste from the intermediate levels are trammed to orepasses for delivery to the lowermost haulage level servicing an ore body. The final result may be visualized as a number of small mines within a large mine. The problems of high development costs and high total development time, and the large amount and high cost of providing materials handl ing and ore haulage service while producing from this isolated type of stope block, made it desirable to consider totally new approaches in developing and mining a number of similar areas.

Jan 1, 1971

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By David S. Smith

Almost nine years after the assertion of enormous and pervasive federal control over coal mines by means of the Federal Coal Mine Safety and Health Act of 1969, 30 USC Section 801 et seq, as amended by the Federal Mine Safety and Health Act of 1977 (which basically increases the punitive powers of government) a brief assessment of some of the underlying causes, present status, and possible alternatives to governmental control is appropriate. In a governmental system based upon the principles of democracy and the protection of individual freedoms and constitutional rights the ultimate mechanism for abrogation of these rights is the creation and exploitation of fear. Machiavelli in rendering advice concerning the power over men provided by fear stated, "... it is much safer to be feared than loved .. fear preserves (the government) by a dread of punishment which never fails." The Prince. Within the context of the assumption of control by the government over industries or segments of our population - popular fear provides a convenient and almost necessary mechanism for the avoidance by law or regulation of democratic principles. The popular fear of coal mines has been successfully exploited by various goal oriented groups in the past and most recently by a Congressional constituency with a vested interest in controlling the mines through regulation.

Jan 1, 1979

By Dennis S. Kostick

Soda ash is the common name for sodium carbonate (Na2CO3), an alkali compound that is the 11th largest inorganic chemical in terms of production of all domestic inorganic and organic chemicals, excluding petrochemical feedstocks. Despite that most people have never heard of soda ash, it is an important industrial compound used to manufacture glass, chemicals, soaps and detergents, pulp and paper, and many other familiar consumer products. Natural alkalis have been used by mankind for thousands of years; however, their industrial manufacture dates back to only the latter half of the 18th century. Natural deposits of sodium carbonate have been known as early as about 3500 BC, when the Egyptians used natural soda ash in making glass. They also mixed lime and soda ash to make sodium hydroxide (caustic soda) that was combined with silicate minerals found in the Sinai desert. This made a soluble silica, which when added to aluminum-rich silt from the Nile River, produced a silica- aluminate cement mortar with excellent bonding properties for construction. The Romans in the first century AD also used natural soda ash in glass manufacture but expanded its use medically for the treatment of colic pains and skin eruptions, and in the making of bread. Elsewhere, people used the ashes of wood to obtain their source of alkali. People learned over time that different types of wood yielded various ashes with different properties; therefore, various plants were burned specifically for their ashes. Ash from plants grown in salt-bearing soils (such as saltwort) and from kelp and other seaweeds, especially Spanish barilla, were so different from ashes obtained from other vegetation that it became known as soda ash (due to its sodium content) versus pot ash, a potassium-based alkali ash. About 13 t of barilla ashes produced 1 t of sodium carbonate and 14 kg of iodine as a byproduct. The difference between these two ashes was relatively obscure until Duhamel Dumonceau made the distinction clear in 1736. The word soda ash developed from common usage and is perhaps more well known today than its synonym sodium carbonate. One of the primary ores of soda ash is trona, a sodium carbonate-bearing mineral that's name is traced back to Arabic origin. Trona also is known internationally by other names such as urao (Venezuela), kaum (Nigeria), natron (from Greek nitron and Latin natrium), and szekso (Hungary). The beginning of the Industrial Revolution in Western Europe in the late 18th century soon put a strain on the availability of raw materials to meet consumer demands. One of these scarce materials was soda ash. Because of the Seven Years War with England and the Napoleonic wars with other parts of Europe, France could not obtain sufficient quantities of Spanish barilla or other supplies of vegetable alkali to meet the growing demand. Efforts were needed to synthesize soda ash. In 1775, the French Academy of Sciences offered a large prize of 2,400 livres to someone who could find an inexpensive method to make soda ash. In September 1791 at St. Denis, Nicolas Leblanc (1742- 1806), a French chemist, developed such a technique using salt, sulfuric acid, coal, and limestone. The French Revolution interfered with its development, and his patent and factory were confiscated with Leblanc receiving only token compensation. Napoleon returned his factory to him; however, Leblanc was not able to raise enough capital to reopen it, and he committed suicide in 1806. A small, but not particularly successful, Leblanc plant was established in England in 1814. It was not until 1823 when the process first became commercially successful in Liverpool, England. The process was introduced in Germany in 1843 and in Austria in 1851 (Harness and Coons, 1942). Soda ash production by the Leblanc process reached its peak of about 599 500 t in 1880, after which it began to decline as the Solvay process became more popular. The Leblanc process was used to a limited extent in Europe during World War I but had disappeared by World War II. The Solvay process, also known as the ammonia-soda process, was developed by Alfred and Ernest (1 838-1922) Solvay in 1861 based on a concept by Fresnel that had been known since 1811. For the next 50 years, the implementation of the idea evaded industrial chemists because no large-scale and economic means could be found to commercialize the concept. Although Ernest Solvay was unaware of the existance of an ammonia-soda concept, he solved the problems by utilizing carbonating towers. The Solvay process produced soda ash from salt, limestone, and coke, with ammonia as a catalyst. With a capital of 136,000 francs, the first plant was built by the Solvay brothers at Couillet, Belgium, in 1863 with production commencing in 1865. Synthetic soda ash production amounted to 1.5 tpd in 1866, but reached 10 tpd by 1872. They patented their use of carbonating towers in 1872 that had made ammonia-soda manufacturing a successful continuous process. Their second plant was built in 1872 at Dombasle, France. In 1874, the first Solvay plant in England was built at Northwich by Ludwig Mond, the namesake of Brunner Mond and Co. (formerly Imperial Chemical Industries), the company that currently operates the two English Solvay plants. In the United States, William B. Cogswell in February 1879 heard a presentation on the Solvay process and sailed to Europe to meet with the Solvay brothers to seek their support for using their process in New York. At first, the brothers were not interested; however, Mr. Cogswell was persistent and ultimately gained their support. The Solvay Rocess Co. was formed Sep. 2 1, 1881, and construction began immediately on the first Solvay plant at Geddes, near Syracuse, NY. The plant came onstream Jan. 10, 1884, and produced 11 180 t in its first year of operation. In 1910, rotary calciners were installed that increased capacity to 1 000 tpd. By 1930, plant capacity was up to 2 400 tpd. The facility remained in continuous operation for more than 100 years. By 1939. 10 Solvay soda ash plants were in operation in 6 States throughout the nation. The Syracuse plant was officially closed Jan. 6, 1986, with total shutdown completed by Feb. 1986. Ironically, this facility was the first Solvay plant as well as the last. Other than the first Solvay plant beginning in 1884, the majority of US soda ash supplies during the 19th century came from imports. The remainder of the US supply

Jan 1, 1994

By M. Misra, I. A. H. Schneider

The flocculation of -38 pm calcite, hematite and kaolinite aqueous suspensions by the yeast Candida parapsilosis and products derived from rupture of the microorganism was studied. Flocculation of hematite suspensions by the microorganism and its derivatives readily takes place between pH 2.8 and 11.4. Maximum flocculation occurs at about pH 6.5. Flocculation of calcite suspensions by the microorganism and its derivatives readily takes place between pH 7.0 and 11.8. Maximum flocculation occurs at about pH 10.0. Flocculation of kaolinite suspensions was less than that for the other two minerals. However, a soluble fraction derived from the rupture of the organism functioned as a good flocculant for the mineral, albeit at an increased concentration, between pH 2.6 and 11.5. Maximum flocculation occurs between pH 6.8 and 7.2. An attempt is made to relate the behavior of the various systems to the surface characteristics of the minerals and the surface and chemical properties of microorganism and its derivatives. Experimentation used to evaluate the flocculation includes actual flocculation tests, microelectrophoresis measurements and scanning electron microscopy.

Jan 1, 1994

By W. J. Kennedy

Energy management in industry has recently achieved notice as a way to reduce costs without decreasing production. The same approach used in industry can be used in mining, even though the processes are different. This approach is based upon a three phase system of data collection, implementation, and monitoring, all aimed at gathering and evaluating information in such a way as to have a maximum impact on energy costs. This approach has these advantages: (1) attention is directed toward the part of each mining system where the most energy is used, (2) input is collected systematically from all persons involved in the operation of each system, and (3) a means of monitoring the progress toward established goals is created. The mining systems considered are truck haulage, conveyor haulage, blasting and crushing, and lighting. After describing the general procedure, the authors have described a specific method for improving the efficiency (and hence the energy consumption) of round-trip truck haul age systems.

Jan 1, 1982

By N. P. Titkov

This paper presents the results of laboratory and pilot plant investigations for the development of efficient methods of beneficiating hematite ores from the Krivoi Rog, Kursk Magnetic Anomoly, Olenogorsk, and other localities. The tests included gravity, magnetic (in a high intensity field), flota¬tion, and magnetizing roasting methods. It was possible to develop efficient beneficiation methods depending on the mineral composition of the ore and degree of dissemination of ore and gangue minerals. The paper shows the relationship between the iron silicate and quartz content of the ore and the technologic indices of the various beneficiation methods. Some of the conclusions based on these investigations and the technical and economic computations related to the cost of one ton of pig iron produced from concentrates obtained by the various beneficiation methods are: 1. If the hematite ore is not disseminated uniformly, it is expedient to use a combined gravity and flotation process. Ore particles up to 50 am. in size are beneficiated by gravity (heavy suspension, jigging, and others) and yield a lump concentrate. The middlings from this process are recrushed and floated; 2. Finely disseminated hematite ores, containing small quantities (less than 5 percent) of iron silicates, are most effectively beneficiated by flotation. Anionic (sulphate soap, tall oil emulsion with various foam depressors) as well as cationic collectors may be used. Depending on the mineral and chemical composition of the ore, it is possible to obtain concentrates containing up to 65 percent iron with an extraction up to 94 percent; 3. Finely disseminated, mixed hematite-magnetite ores may be beneficiated by flotation or a magnetic separation-flotation process; 4. Finely disseminated hematite ores, containing large quantities of iron silicates and earthy hematite ores are most efficiently beneficiated by the magnetizing roasting method. This method will yield concentrates containing up to 68 percent iron with extractions up to 90 percent. Although beneficiation by the magnetizing roasting process is costly, it will nonetheless, when employed on this type of ore, yield the least expensive pig iron.

Jan 1, 1960

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016