Search Documents

By Julian Prada

Tunneling requirements are presenting designers with greater challenges. The design and construction of the 2000-ft long unidirectional twin highway tunnels for the approach to one of two bridges of the Louisville-Southern Indiana Ohio River Bridges (LSIORB) Project is no exception. Excavation under low cover, beneath an historic site, with each tunnel of 70-feet wide and 50-feet high dimensions will set precedents for US highway tunnel excavation size. To investigate ground conditions to supplement final design of the highway tunnels, an exploratory tunnel excavated through karstic limestone and shale will be located within the confines of the proposed final alignment. With the LSIORB Project, Jefferson County, Kentucky and Clark County, Indiana will have improved cross-river mobility between them. The Indiana Department of Transportation (INDOT) and the Kentucky Transportation Cabinet (KYTC) are developing the LSIORB Project jointly, in coordination with the Federal Highway Administration (FHWA). Section 4, one of six sections, as shown in Figure 1 is the East End Kentucky Approach and Connections to I-265. Key elements of Section 4 are the twin three-lane highway tunnels under the historic Drumanard Estate. The property is located on the north side of US Highway 42 (US 42) at the intersection with the Gene Snyder Freeway (also KY841) as shown in Figure 2. One aspect of the project consists of the excavation of an Exploratory Tunnel along the southbound alignment tunnel. At the time of preparation of this paper, KYTC has not awarded the Exploratory Tunnel Contract. This paper will focus on the planned geotechnical investigation program that will occur during excavation of the exploratory tunnel and how the design of the twin highway tunnels will incorporate the findings to achieve an innovative and efficient configuration.

Jan 1, 2008

By N. P. Widodo

The ventilation measurements by tracer gas method at Pongkor gold mine show that effective diffusion coefficient, E, at straight airways indicated a similar range of measured one by the laboratory experiments which can be estimated by Taylor equation. On the other hand, E of the curved airways in the mine was estimated as larger than that of the straight ones (1.5 to 32 times than that obtained by the Taylor equation and these have been compared with the data measured in Kushiro coal mine, Japan). The curved mine airways, with small curvature against airway radius and complex velocity profile, possibly give concentration ? time curves with long tailings, thus those airway conditions could make larger E. Laboratory experiments of gas diffusion by a pulsed injection of small amount gas, into straight and curved airways, have been conducted in order to investigate a range of E in mine airways. The plots of E against Reynolds number show that the present laboratory results of straight-long airways are almost close to one calculated by Taylor equation. On the other hand, the values of E measured at curved single-direction airways were smaller than that of the straight airways, which may be due to effects by secondary vortexes flow in the curved airways.

Jan 1, 2009

GE Industrial Systems has received a multimillion dollar contract from Bucyrus International to supply complete electrical systems for three new draglines. These machines will be installed at Coal India’s Northern Coalfields’ Dudhichua and Nigahi open cast mines. The Dudhichua and Nigahi mines are located south of Varanasi. They produce Type C and Type E coal for use in the region’s super-thermal power stations. The GE systems will power and control the drag, hoist and swing motions of one Bucyrus W2000 walking dragline at Dudhichua and two a Nigahi.

Jan 1, 2000

By Neil A. Brown

The trona deposits near Green River, in southwestern Wyoming are world class in size and quality. They contain more than 25 times the reserves of the next largest trona deposit at Lake Magadi in Kenya. Based on present rates of production, the Green River reserve should last for more than 500 years. Since their discovery in 1938, the Union Pacific Corp. has been instrumental in the promotion, development and production of soda ash in Wyoming. Union Pacific spent several years drilling the deposits and trying to promote them to chemical companies. In 1947, Westvaco and Union Pacific entered into what became the first trona lease agreement. Today, the Green River Basin leads the world in soda ash production, accounting for about 25% of the world's supply. Green River producers process more than 14.5 Mt/a (16 million stpy) of trona to produce more than 8 Mt/a (9 million stpy) of soda ash. The future for Green River soda ash looks good, with more of the world looking towards the cheaper and higher quality source of soda ash coming from the natural deposits. Production from the Green River deposits should continue to grow as trade barriers and tariffs begin to fall in Europe and energy and environmental costs force the synthetic producers to exit the market.

Jan 1, 1995

By Paul Lynch

"Since being reported to the 2012 UMI in Shanghai, the Cook Islands has been steadily developing for the commencement of it Seabed Minerals sector in its large Exclusive Economic Zone which contain a vast and unique Manganese Nodule resource, estimated at 10 billion tonnes1. At the 2013 UMI in Brazil, it was reported that the Seabed Minerals Act had commenced and all the necessary complex Technical aspects of this developmental work was being undertaken. At the 2014 UMI in Portugal, full details of the final developments leading to the opening of the Tender of Exploration Blocks in the Cook Islands EEZ will be presented in a brief but comprehensive method, using Poster displays, Powerpoint and active Website interaction. This will show the drafted Regulations, prepared on best international standards, to address both Licencing and Environmental requirements, to give clarity and security to the Resources Owner, industry and stakeholders. This work in being coordinated by the Cook Islands Seabed Minerals Authority, with the valuable collaboration of many international, regional and national stakeholders, including the Cook Islands NGOs, Marine Resources, Marine Park and National Environment Service."

Sep 1, 2014

By Thomas N. Walthier

This paper will review world trends that are increasingly restrictive of mineral exploration and mining throughout the Free World This is occurring in the face of projected huge increases in demand for mineral products Some of the impediments are direct and absolute; others are indirect, but nevertheless effective; still others represent merely hostile attitudes Many of the world governments have a reputation for lack of integrity in dealing with existing foreign investments within their borders, and consequently are quite uninviting places for new investments, especially in the capital intensive natural resources industry. Compared with even 35 odd years ago (and pre-World War II is not that long ago) there are few places left where private mining investments are both wanted and where investors are willing, to go. We shall begin with an analysis of conditions in the U. S., shift to neighboring Canada and Flexico, and then have a look around the world. As the world grows smaller for the private mining sector, the function of exploration, development, and operation is passing over to government. We'll conclude with a view of what this holds for the future

Jan 1, 1976

By S. Ripke

Between 2002 and 2004, the performance of a six million ton per year iron ore beneficiation plant dropped significantly. In a classic case of “who done it,” was it the mine, the concentrator, an ore change, or something else? While average annual final product grade decreased 8% (indicated by an increase in silicate gangue from 2.76% to 2.99%), the weight recovery also decreased by 8% (from 37.92% to 34.79%). This represents a loss of 832,000 tons of iron ore worth about $16 million for the two year period! The concentrator had been optimized to produce a high grade wet concentrate as feed to the dry side of the plant. But, did optimizing an individual unit operation’s grade give the best overall plant performance? In this paper, the investigation and solution to this mystery will be revealed.

Jan 1, 2007

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By David G. Adam

Introduction Syncrude Canada Ltd. is the operating company for a consortium of industry and government participants that produce synthetic crude oil from their leases in the Athabasca Oil Sands. Production from the $2.3 billion (1978) integrated mining, extraction, and bitumen upgrading and utility complex started in September 1978. Production is currently about 6.4 Mm3/a (40 million bbl per year) of high quality synthetic crude oil. This is done by upgrading the extracted bitumen from the oil sands mined. Plans are to increase the production to 8 Mm3/a (50 million bbl pier year) by 1989. At that time, the mining operation will be required to deliver 100 Mt/a (110 million stpy) of oil sand (ore) to the extraction plants, and handle quantities of waste ranging from 50 to 75 Mt/a (55 to 83 million stpy). The Syncrude plant is located at Mildred Lake, 40 km (25 miles) north of Fort McMurray and 480 km (300 miles) north of Edmonton, Alberta. Climate, particularly winter, is therefore a major factor affecting the design and operation of all the Syncrude production facilities. Bitumen production, consisting of overburden removal, oil/sand mining, bitumen extraction, and tailings disposal, account for about half the total SCO production costs. Considerable research and development, therefore, continues to be applied to improve both material handling and bitumen recovery methods. Potential applications for feeder breakers were identified in the material handling aspects of both overburden and oil sand mining to reduce cost and to attain planned production increments. Overburden removal Overburden materials on the leases comprise thin Pleistocene sands, gravel and fill, and sands, silts and clays of the thicker Clearwater Formation with the silt to clay components predominating. The latter contains multiple leases of hard siltstone with unconfined compressive strengths up to 148 MPa and thicknesses up 0.1 to 0.9 m (1 to 3ft). Characteristics of the overburden as well as the climatic environment and scale of operation present unique problems for the efficient removal of the material. In a bucketwheel/conveyor system, the weak silty clay formations require relatively flat working slopes for safe operation, while the siltstone lenses and frozen overburden require blasting or selective removal by other equipment. These factors, combined with the normal bucketwheel/conveyor design parameters, lead to high capital investment and relatively inefficient use of that capital. Hydraulic mining alternatives, including dredging, are constrained by severe clay settling problems in the waste disposal

Jan 6, 1986

By Lynn B. Hales

There is a large economic opportunity associated with improving metallurgical performance in mineral processing plants that use process control. Thus, future control systems will be developed towards more sophisticated user friendly, computer-based systems that use powerful software analysis and control techniques. Auto-tuning, adaptive control and process models will gain expanded use because of their transparent availability to the system designer. Control of individual unit operations will be optimized and coordinated through expert systems that monitor economic conditions and management directives and direct operations accordingly. Plant areas, once considered cost centers, will be integrated into plant-wide control systems for economic control and optimization. This article looks at new control hardware, process sensors, control strategies and software development tools. It also looks at the economics driving the continued development of advanced process control systems. Process control systems routinely used in the mining industry were born when the microprocessor was invented. They have continued along an evolutionary path from vendor specific processing hardware and proprietary operating systems to computer industry standard "open architecture" systems. The many economic forces that drive the development and functionality of these process control systems will cause this evolutionary process to continue. Two of the broadest categories are the needs of the end users and the desire of the system manufacturers to distinguish their products from one another. More

Jan 1, 1994

By T. W. Beck

Drilling into coal mine roof strata to install roof bolts has the potential to release substantial quantities of respirable dust. Due to the proximity of drill holes to the breathing zone of roof bolting personnel, dusts escaping the holes and avoiding capture by the dust collection system pose a potential respiratory health risk. Controls are available to complement the typical dry vacuum collection system and minimize harmful exposures during the initial phase of drilling. This paper examines the use of a bit sleeve in combination with a dust hog-type bit to improve dust extraction during the critical initial phase of drilling. A twisted-body drill bit is also evaluated to determine the quantity of dust liberated by comparison to the dust hog-type bit. Based on these laboratory tests, the bit sleeve may reduce dust emissions by one-half during the initial phase of drilling before the drill bit is fully enclosed by the drill hole. Because collaring is responsible for the largest dust liberations, overall dust emissions can also be substantially reduced. The use of a twisted-body bit has minimal improvement on dust capture compared to the commonly used dust hog-type bit.

Feb 27, 2013

By J. C. Yingling, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Much of the land reclaimed since enactment of the 1977 Surface Mining Control and Reclamation Act is over-compacted. Research has shown that excessive compaction in replaced growing media is detrimental to establishment of trees. If trees are to be grown on reclaimed surface mined sites, something must be done to alleviate this excessive compaction. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed growing media. The University of Kentucky has developed test cells on reclaimed sites at a surface mine in eastern Kentucky to determine the impact of tillage (ripping) on soil compaction and tree survival rate. The ripping methods being evaluated include shallow tillage using conventional farm equipment and deep tillage using a dozer with a ripping arm. The impact of organic soil supplements on soil physical properties and tree survival rates is also being evaluated at the site. The organic soil supplements being evaluated include application of hardwood bark and application of straw and mulch. Each test cell has been planted with various species of trees, and for the first two years, data have been collected at these test cells for soil dry bulk density, penetration depth and resistance, and survival rate of trees. These data are currently being correlated to determine how ripping and the application of organic soil supplements affects the relationship between soil compaction and tree survival rate.

Jan 1, 2002

By K. Sasaki, W. Astuti, N. Okibe, T. Hirajima

"The kinetics of leaching of a saprolitic ore from Indonesia by citric acid solution under atmospheric pressure was investigated. An examination of the effects of leaching temperature, citric acid concentration, pulp density and ore particle size on the dissolution rate of nickel found that they all had significant influence on the rate. The highest nickel recovery (95.6 percent) was achieved under the leaching conditions of ore particle size of 212-355 microns, citric acid concentration of 1 M, leaching time of 15 days, pulp density of 20 weight/volume percent, leaching temperature of 40°C and shaker speed of 200 rpm. The shrinking core model was found to be appropriate for describing the leaching kinetics of this ore in citric acid solutions at atmospheric pressure. The experimental data were well interpreted by this model with rate of reaction controlled by diffusion through the solid product layer. Using the Arrhenius expression, the apparent activation energy for nickel dissolution was evaluated as 12.38 kJ/mol. Finally, on the basis of the shrinking core model, a proposed empirical kinetic model for the leaching of nickel from this Indonesian saprolitic ore was expressed as a mathematical model, which was verified as consistent with the observed experimental results.IntroductionIndonesia has some of the world’s largest nickel laterite reserves and was the largest producer of nickel – in the form of nickel lateritic ores – in the world in 2013 (Merchant Research and Consulting Ltd, 2014). However, only high-grade saprolites are processed in Indonesia using pyrometallurgical methods to produce ferronickel and nickel matte. Lower-grade saprolites and limonites are removed, becoming waste or overburden in mining site areas. Hydrometallurgical methods, involving either chemical leaching or bioleaching, are now seen as the most important technologies for treating nickel laterites in the future because of their advantage of not only extracting nickel and iron but also other valuable elements. In addition, hydrometallurgical methods consume less energy and have lower capital and operational costs. Although they are recognized to be more suited to limonites, some researchers have studied their use in the extraction of nickel and other metals from saprolites (Guo et al., 2009; Lu et al., 2013). Hydrometallurgical processes for the extraction of metals, especially nickel, promise to be meaningful alternatives to pyrometallurgical processes to primarily treat low-grade saprolites for which pyrometallurgical processing is not favorable"

Jan 1, 2015

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Abstract-Since 1982, the US Bureau of Mines has inves¬tigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (<_1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars he provided only in mines >_1.07 m (42 in.). However, court obtained variances are granted to mines <_1.22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1989

New developments in the pipe conveyor and belt are advanced to address the growth in the capacity, length and complexity of pipe conveyor systems. Improved belt construction can offer better stability during horizontal curves and resistance to twist. Low rolling resistance rubber compound can significantly lower the power consumption and belt tension, producing capital and operation cost savings. Dynamic analysis, when used to analyze the conveyor?s starting and stopping behavior, can improve the design and reliability of long overland pipe conveyor systems. For these three aspects, technical backgrounds and field installations as examples are discussed in this paper.

Jan 1, 2012

By F. Bruey

The Factorial Model Experimenters are often interested in systems that are multi-factorial. A multi-factorial system is one whose output is believed or known to be dependent on the particular settings of several inputs, or factors. We can think of these factors as defining a space, with each point in this space corresponding to a particular set of factor settings. Experimenting can be thought of as exploring this space - finding out how the response of the system changes as factor settings are changed. There are several challenges in this exploration, among which are deciding what region to explore, designing an experiment that explores it most effectively, and describing the results of the exploration. This paper deals principally with the last of these; it shows how the factorial model can be used to describe how the response of the system changes as factor settings are changed. A strength of the factorial model is that it treats the factors as causes of change in the system&apos;s response and focuses on relations among these causes. In particular, the factorial model focuses on whether causes act independently on the system (in a sense to be explained below), or whether they interact. This is important because the experimenter generally seeks to control the system, and because control based on causes that act independently of other causes is relatively simple, whereas control based on causes that interact is more challenging. Also, mapping the space - finding out how the response of the system changes as factor settings are changed - will require less work if, during the exploration, it can be determined which of the causes act independently. For the sake of example, let us assume that the space we are exploring is three-dimensional, and that we have already defined, for each of the three factors, the range of interest. Let us consider all the ways in which the response of the system might depend on the settings of these three factors. In the simplest case, the response in this region does not depend on any of the factors. The response is constant throughout the space, at say, 80 units.

Jan 1, 2007

By S. Strömberg, A. Jokilaakso

Two complex copper concentrates and one arsenical nickel concentrate were oxidized in simulated flash smelting conditions using a laminar-flow furnace. The concentrates contained tetrahedrite as Sb-bearing mineral and arsenopyrite and gersdorfite as As-bearing minerals. At high temperatures and low oxygen potentials, Sb tended to vaporize, but with high oxygen potentials it was captured in mixed oxide phases with copper and iron. Arsenic was found to follow antimony in copper concentrates, although with less sharp contrast between low and high oxygen potentials. In the nickel concentrate studied, arsenic was found to vaporize from the gersdorffite particles and, subsequently, condense on the other particles.

Jan 1, 1998

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today&apos;s apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery&apos;s capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By Brian Fulcher

While tunneling in Europe has been a tradition for centuries, many companies and countries have embraced tunnel innovation with considerable vigor and creativity. Indeed, local needs and site conditions have provided the initiative for improved means, methods, materials and equipment to complete progressively more challenging projects. Many recently completed tunnels have expanded tunneling technology and contributed to the development of highly specialized and productive equipment ? such as the mixed-mode tunnel boring ma-chine (TBM) presently in operation at the SOCATOP A- [ ] 86 road tunnel and the high-pressure slurry TBMs for the Westerschelde Tunnel in the Netherlands and Hollandsas near Malmo, Sweden. This paper describes some of the key technologies employed by European tunnel builders and designers including the New Austrian Tunneling Method (NATM), advanced earth pressure-balanced (EPB) machines, pres-sure-faced (slurry) tunneling machines as well as ?hybrid? or mixed-mode TBMs. While these tunneling methods and equipment generally involve significant equipment investment, they may also involve highly trained, experienced and specialized tunneling and support crews as well as materials and tools specifically developed to supplement or complement tunneling performance. For example, mechanized pipe arch placement substantially improves ground support measures and NATM advance and on larger tunnel cross-sections.

Jan 1, 2007

By Tim O’Neil

The earthmover tire shortage has been a case of bust and boom for the tire industry. Tire producers were unwilling to invest ahead of the mining boom. In their defense, though, the metals sector of the mining industry tends to be cyclic, tire manufacturers are not prescient. Until two years ago, low tire demand depressed prices. The incentive to invest in new, big-tire capacity was almost nonexistent, according to Prashant Prabhu, president of Michelin Earthmover Tire worldwide. “There has been very poor anticipation or a miscaluation of the amplitude of the (tire) demand on the part of just about everybody,” said Prabhu. What a turnaround. The earthmover tire market has grown by 30 percent over the past two years. Now there are not enough earth-mover tires and likely won’t be for the next two years. Goodyear said it was offering customers bias-ply tires when it could not supply enough radial-ply tires. Komatsu said it lost equipment sales because it could not provide the tires that customers requested. Volvo and Caterpillar said they are delivering some vehicles without tires, either promising tires later or leaving the customers – mine operators – to find their own rubber.

Jan 1, 2006