Search Documents

By P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines has been engineered, designed and operated. A non-transferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide, and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained at above 1673 K (1400 C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbon monoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pressure, and average reactor temperature. The interactions of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1993

By George C. Carter

It was just a little over three years ago that the "Go" button was pushed to start operations on the blending piles at Oro Grande. As is usual with any new installation, there were problems that had to be solved. This paper will concern itself with those problems directly related to quality control. To obtain a consistent outgoing quality level at the most economical level for a finished product requires two main points: 1. Measurement of variations in the process, 2. A method of making a predictable change to adjust for variations. The manufacture of cement requires a relatively high degree of accuracy if a consistent outgoing quality level is to be maintained. The blending piles were our solution to this problem.

Jan 1, 1962

By C. Leal

Modern production has as goal to reach high and uniform quality in their products. To success with this, it is essential to have a good knowledge of the different variables involved in the process. Investigation or analysis of a process or system has as references the measurements of the variables. These measurements are presented normally in form of data. These data are measured in intervals over time. The aim with measurement of the data in a process is to obtain information about the state of it in order to have it under control. Other goal is to know how the results are affected by the process variables to improve upon product quality, redunding manufacturing cost, better pollution control etc.

Jan 1, 1994

By C. Duke

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By R. L. Michalowski

The operation of mobile mining equipment near the crest of stockpiles and wastedumps is a potentially hazardous practice which often results in localized slope failures. A limit plasticity approach to determine the total admissible weight for moving loads near slope crests is presented. A three-dimensional analysis provides an upper bound solution to the load that can be applied to the top of the slope (dump point), and it also provides the critical distances of the load from the slope crests. The analysis accounts for the inertial forces generated by the deceleration of a moving load (e.g., a dump truck), and it also includes the drag resistance of the front wheels if the brakes are engaged. The results can be utilized to determine the safe operating distances for mobile equipment from the slope edge. This presentation will discuss the application of limit plasticity to the development of the local three-dimensional collapse mechanism. An example with realistic parameters also will be presented.

Jan 1, 1991

By R. Q. Honaker

Although the fundamental principles of hindered bed classifiers are relatively simple, the complex interactions between the operating parameters provide a degree of difficulty that hinders the ability for on-line plant optimization. Thus, a dynamic population balance model was developed for determining the hindered settling velocity of particles varying in density and size. The steady-state results of the model include partition curves as a function of particle size and density as well as metallurgical data. A statistical comparison of the simulation results with those obtained from industrial units reveal a high level of accuracy with adjusted R2 values greater than 0.95.

Jan 1, 1999

By K. V. Raj, T. Bhowmick

"Computational fluid dynamics (CFD) modeling of an open-pit mine has several challenges. A good quality mesh of the model domain is a pre-requisite for convergence in solution. Good quality tetrahedral meshing and insertion of prism layers in faceted open-pit mine geometry is complicated due to presence of numerous vertices and ridges. Presence of vertices and ridges result in poor quality tetra elements and holes in prism layers, which cause instability in the model. Good quality pit bottom prism mesh elements significantly improve the formation of velocity boundary layer and thermal boundary layer at the pit bottom. This results in an expected temperature dependent micrometeorological buoyancy flow in the pit. Whereas, model geometry without a prism layer, results in abrupt temperature gradient near pit bottom. Buoyancy flow and recirculation have significant effect in lifting mechanism of fugitive dust particles generated near pit bottom. Representative initial and boundary conditions and selection of appropriate turbulence model have significant influences on the simulation results. In this paper, three-dimensional models of open-pit mines are developed using commercial CFD software (CRADLE-CFD). Important constraints and various consequences in modeling complex open-pit geometries are presented. INTRODUCTION Application of Computational fluid dynamics (CFD) to model an open-pit mine to predict fugitive dust and pollutant concentrations in and around a mine is relatively new. In former Soviet republic (USSR), Baklanov [1] and Belousov [2, 3] presented numerical models of pollutant transport in open-pit mines in Arctic regions. In recent years, advances in mathematical and computational fields have enabled better modeling of pollutant dispersion phenomenon around mines using computational fluid dynamics (CFD). Several CFD software packages have been used by various researchers to model the pollutant transport in open-pit mines. Works by Alvarez et al. [4]; Lowndes et al. [5]; Silvester et al. [6]; Torno et al. [7]; Choudhury and Bandopadhyay [8]; Collingwood et al. [9]; Raj et al. [10] and Flores et al. [11]; are examples of application of various commercial and open source CFD packages (COMSOL, ANSYS, OpenFOAM) to model pollutant transport in open-pit mines. These researches provided a strong background for additional research involving CFD modeling of open-pit mines. Due to the limitations of computational times and capacity, 3D modeling and various aspects of fugitive dust dispersion in open-pit mines remained unexplored."

Jan 1, 2015

By Alberto Tarsitani

The existing Rome-Florence railroad capacity is inadequate for the traffic volume. To increase this capacity and to reduce the traveling time the Italian National Railroad Administration has decided to provide an additional 400% of rail capacity. This new rail line will be known as the Direttissima Roma-Florence line. It is planned to operate the trains on this connection at speeds of 250 km per hr. Table 1 lists the main design characteristics. [TABLE 1. Design Characteristics Design speed250 km per hr Maximum inclination80 00 (0.8%) Minimum curve radius3000 m Minimum vertical curve radius30,000 m Maximum superelevation in curve 425 mm Type of rail60 kg per m welded] The new rail line will be connected to the existing one by means of high speed switches called "interconnections" so that parts of the new line can be used also by local trains. Construction works for this new line have been divided by the railroad administration into eight sections. Five of these have already been committed to joint ventures. Castiglione Tunnel is a part of the fifth section, 42 km in length, which has been awarded to Consorzio Ferrofir which is a joint venture composed of the construction firms of Astaldi - Di Penta - Lodigiani - Sogene.

Jan 1, 1974

By F. C. Bond

History The breaking and shaping of rock was one of man's earliest occupations. In the Paleolithic Age long before the dawn of history, arrow¬smiths and the makers of stone axes, hammers, knives, scrapers, spears, and borers were highly respected members of society. In early historical times stones for building blocks, roads, and city walls were shaped by slaves and convicts, who also did most of the mining. However, great artists erected beautiful stone sculptures, while gifted architects planned imposing temples and monuments. Until well into the 19th century nearly all rock was broken laboriously by hand. The small rock required by John MacAdam for his macadamized roads in England in the 1820s was produced by women and boys seated alongside the roadside with hand hammers and legs wrapped with rags. Eli Whitney Blake, a nephew of the Eli Whitney who invented the cotton gin, developed the first successful jaw crusher before 1870. The gyratory conical crusher soon followed. Comparative tests established its large capacity advantage over the jaw crusher, as well as its greater cost for a given feed size. Both types have been in use for more than 100 years. Crushing rolls appeared before 1900. Thomas A. Edison made very large diameter rolls which were excessively long; they failed because of shaft deflection. Various types of disk crushers and edge runner rolls appeared about this time. The older methods of reducing rock were adaptations of other processes. The stamp battery of dropping weights effected crushing by simulating heavy hammer blows; the much earlier arrastre, in which heavy stones were dragged in a circular path over the ore by animal power, came from the prehistoric method of grinding grain between two rubbing stones, while the jaw crusher was adapted from simple squeezing devices. But the tumbling grinding mill was not just an adaptation; it was an invention, because it required thinking on a somewhat higher order-there was no prototype. Its nearest antecedents were probably the small closed tumbling drums used in England more than a century ago for cleaning and polishing small iron castings. The date of the first tumbling mill actually used to grind rock is unknown, but it was later than the American Civil War (1861¬1865). It was almost certainly a closed or batch mill in which rock was placed and rotated until it reached the desired particle size. It could have been operated either wet or dry. The first published refer¬ence to such a batch mill was one introduced by Alsing in England (1870) for the grinding of calcined flints for pottery work.21 There are several rather indefinite reports of grinding mills in the early 1890s, including an overflow ball mill in the Helena and Livingstone reduction plant in Montana which may have been the first of its kind. 11 Many of the first mills, which were called tube mills, used hard rock both as grinding media and as mill lining. The rock used was preferably stone from the Normandy and Danish beaches, when it could be imported. This remarkable siliceous stone was already widely used for grist mills throughout America, and its resistance to wear was greatly respected. The decade of the 1890s saw the development of tumbling mills with continuous feed and discharge and their extension into different industrial uses. By 1895 some experience had been accumulated. Iron grinding balls were being tested and the proper speed of rotation was being determined. The Clark Patent tube mill was featured in an E. P. Allis bulletin of 1890, which may have been the first published description of a tube mill. More than 1,000 Gates tube mills had been built by Allis-Chalmers before 1913. Many of these were used in gold mining, espe¬cially in South Africa. The 5 x 22-ft size was particularly favored for grinding portland cement; the use of tumbling mills in the manufac¬ture of cement began about 1900. A great deal of attention was paid to the mill lining. Metal was then relatively expensive, and the general approach was to trap some of the rock grinding media into mill lining pockets. This rock would then absorb the wear and protect the metal lining. In the first ten years of the 20th century there were several different types of pocketed liners, with different manufacturers advancing the superior claims of their patented arrangements. The Osborne liner, developed in South Africa, was probably the most successful. 21 Another item which attracted much attention was size classifica¬tion within the mill and in ancillary equipment attached to the mill and rotating with it. The Krupp type, with interior screens protected inside the mill lining, was developed quite early in Germany, possibly before 1890. The Dorr reciprocating rake classifier (1907) had not yet been invented, and many strange and impractical screening and classifying devices were proposed. In these unsatisfactory machines the two separate processes of size reduction and classification were combined into one operation. It was many years before recognition came that a machine is most efficient when it is designed for one specific purpose. There was much industrial wastage before the opera¬tions of grinding and classification were finally separated. After 1900 the grinding of portland cement raw material and of cement clinker required large numbers of tumbling mills. Most of the raw material was then ground dry. This was also the heyday of gold mining. The old stamp mills that were used in great numbers for grinding gold ore did not grind sufficiently fine to liberate all of the gold, and the new tube mills were installed following the stamps. After 1910 larger diameter tum¬bling mills with larger grinding media were developed. These could receive the finely crushed ore directly, and the inefficient stamp batter¬ies were gradually eliminated. The Rand in South Africa was the greatest gold producer, treating immense quantities of rather low-grade but consistently free milling gold ore. The first tumbling mills, or tube mills, went into operation there in 1904. They were so successful that within a few years no new stamp batteries were installed in the district, even though old ones continued to pound away until after 1950.3 The early tube mills on the Rand all employed Normandy or Danish pebbles, which had to be imported at considerable expense. Their reported wear was as low as 4 lb per ton ground. 4 Many of the mills were lined with the same tough Danish stone cemented into place, while others used the pocketed steel Osborne liner. It was in 1907 on the Rand that an important test was made using hard native ore for grinding media in place of the expensive imported pebbles. 3 This ore, called banket, did not wear as well as the renowned Danish pebbles, but the cost per ton of grinding was definitely reduced. Many of the tube mills on the Rand were soon grinding with native ore. This was the beginning of the development now called autogenous grinding, in which the ore grinds itself. This is treated under a separate heading. See Subsection 3C, Chapter 4. Gold mining was important in America also, and its grinding history follows that of the Rand. Danish pebbles were replaced by native ore in Santa Gertrudis, Mexico, in 1913, 4 and in Consolidated Gold Fields, Nevada, in 1914. 5 Other properties followed suit. However, it gradually became apparent that the capacity of a given mill could be almost doubled if rock grinding media were re¬placed by cast iron or steel grinding balls. In order to increase plant grinding capacity many rock media mills were converted to iron grind¬ing media in the second decade of the present century. In some mills the motor size was doubled; other mills were cut in two and another motor was provided for the second half. Grinding mills began to assume a more modern appearance. Crushing rolls were formerly much used following crushing in jaw or gyratory crushers and preceding grinding in ball mills. How¬ever, the roll surfaces wore rapidly, and skilled maintenance was required to obtain even wear. Rod mills could take feed of the same crusher product size and reduce it finer. The first rod mill was con¬structed by Mine and Smelter Supply Co. and was tested in Canada

Jan 1, 1985

By J. M. Mutmansky

The usual method employed to determine the direction of flow in a connecting airway in advance is to conduct a survey between the two existing nodes being connected by means of the new airway. It is then assumed that airflow will take place from the node with higher pressure to the node with lower pressure. The purpose of this paper is to examine this direction-of-flow problem --using properties of the system characteristic curve for a two-terminal network --and specify some conditions that ensure that flow will take from the higher-pressure node to the lower-pressure node. It is concluded that the only requirement is that all characteristic curves of fans in the network should be strictly decreasing. Five numerical examples illustrate some important properties of the direction-of-flow problem.

Jan 1, 1999

By M. Yekeler

The critical surface tension of wetting values (Ye) of realgar (AsS), talc [Mg3si401o (OH) 2]' stibnite (Sb2S3), and sulfur (S) were determined by flotation in the absence of conventional flotation collectors as 38.7, 38.0, 35.5, and 30.0 dyne/cm, respectively. The surface tensions of flotation media were arranged by methanol. Separation of binary mixtures of these minerals was performed exploiting their Ye differences-which form the basis of the "ganuna flotation process". One step flotation test showed that sulfur floats preferentially from its mixtures with realgar and stibnite at recoveries of 73.6 and 70.7 % and grades of 81.7 and 91.2 %, respectively. The separation of stibnite from realgar gave a recovery of 4.1 % and a grade of 41.2 % for stibnite, indicate that a minimal Ye difference of 3.6±0.2 dyne/cm is essential for such separation when conventional flotation reagents are not used. This paper presents data and describes the approach employed in these separations.

Jan 1, 1994

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By Bond. F. C.

Introduction Although autogenous grinding applications date back to the early years of mineral processing when tumbling-type mills were first used, there has been a renewed interest in this type of grinding over the past few decades. A review of the historical aspects of autogenous grinding is provided which follows the development of the various types of mills and processes. Wet and dry grinding operations using either autogenous or semiautogenous mills, including the Aerofall mill, are described. Em¬phasis has been placed on the test work required to evaluate the feasibility of using autogenous or semiautogenous grinding for a spe¬cific application. The factors which must be considered to establish the appropriate design criteria for these types of grinding circuits are discussed in detail. Successful application of these grinding circuits results from a thorough test program, a careful analysis of the test results, and a practical engineering approach to the design of the process flowsheet and milling equipment. Certain pebble milling applications, where the pebbles consist of the ore or rock itself, can be classified as autogenous pebble mill grinding, or better known as ore-pebble mill grinding. In the generic sense, pebble milling includes those grinding operations using a tum¬bling mill in which the grinding media consists of various types of pebbles, either ore or other pebbles, instead of metal balls. Conse¬quently, this subject is covered separately in Chapter 5, Pebble Mills. Operating data from many of the installations located throughout the world are included in this chapter. Our appreciation is extended to those companies who contributed this important information. History of Autogenous Grinding F. C. BOND Autogenous grinding, the grinding of ore by itself rather than by special metallic or nonmetallic grinding bodies distinct from the ore, has an old and honorable place in the art of mineral processing. It antedates the use of the rod mill and is only a few years younger than the development of the continuously fed rotating tumbling mill in which it is accomplished. Its history71, 72 is inextricably bound up with that of gold mining. Every important early development of autogenous grinding took place on ores of gold, except in one case of silver ore. In common with many other features of modern mineral processing, autogenous grinding would have been greatly retarded if the winning of gold had been so small a part of mining in the past as it is today. Gold unlocked the secrets of rock-on-rock grinding. In years past gold ores were crushed in stamp batteries and then flowed over copper plates covered with mercury which amalgamated the gold. The McArthur Forrest cyanide process for the dissolution of gold in a dilute alkaline cyanide solution appeared in 1890. With finer grinding it recovered more gold than could be won by amalgama¬tion alone. The first response was to stamp in cyanide solution and finer mesh screens guarding the stamp discharge. However, the fine screens greatly restricted the tonnage stamped, and they wore out rapidly. Rotating tumbling mills70, 73 were the obvious choice to grind the coarse product from stamps. Many of these were Gates tube mills; more than 1,000 of these were sold between 1907 and 1913. They were made in 6, 51h, and 5 ft diam, with lengths of 20 and 22 ft. The 5 x 22-ft size was the most popular. The term tube mill did not refer to the mill shape, but included all tumbling mills using grinding pebbles. The flint or chert rocks found along the coasts of Denmark and Normandy are probably the most durable and resistant to abrasive and tumbling wear of any on earth. They were much used in the early tube mills. The early linings were all silex or Danish flint blocks, cemented into place with portland cement. Local hard stones or cast iron blocks were also used later. The cast iron liners carried lifters and were not bolted to the shell, but were held in a tight circle against it by steel wedges hammered home between them. The first ribbed metal liners designed to hold grinding pebbles pounded into them by the mill action were developed at El Oro, Mexico, about 1905. These and the Forbes, Komata, and Tonopah types, as well as the Osborne type developed in South Africa within about five years, were very successful in reducing liner wear. They sometimes lasted two years or more, and equalled or exceeded the life of silex lining at a lower cost. Some of the types were patented. The pioneer name recorded in the history of autogenous grinding is that of Kenneth L. Graham. In 1907 at the Geldenhuis Deep Ltd. mine near Johannesburg, he ran a comparative test on two tube mills. One mill used pieces of the common gold ore, or banket, and the other used the customary imported Danish pebbles as grinding media. He published the first account of autogenous grinding.'' In a test lasting 81 days the ore pebbles showed a definite saving over the Danish pebbles. Graham's historic paper also describes the invention of B. Chew of the Crown Deep Mines of the first trammel to be attached to a grinding mill discharge. The first known account of autogenous grind¬ing printed outside of South Africa was the description of the Graham test in Mining and Scientific Press's The use of grate- vs. overflow¬discharge was also described at this time." The news of this successful test appears to have had immediate effect, for by the end of 1908 the number of tube mills on the Rand had increased from 72 to 120.76 Presumably, most of these mills were now using autogenous grinding. The ore was principally a hard conglomerate of quartz peb¬bles cemented by silica, and was eminently suitable for use as a grind¬ing media. It is unfortunate that in South Africa the new autogenous process continued to be called by its old name of pebble milling, since the name does not distinguish between grinding with ore and grinding with extraneous pebbles. For increased clarity the former is called rock pebble milling. The first historical stage in the development was what is now designated as secondary autogenous grinding, or rock pebble milling. It consists of grinding a feed all passing 'A in. or finer with ore pebbles about 2 to 4 in. in diameter. The next stage to develop was that now called intermediate autogenous grinding, where larger amounts of larger pebbles about 5 in. in size were used to grind ore which had been crushed to about rod mill feed size or somewhat finer. It was developed on the Rand and in other places where coarse stamp screens were used to increase mill tonnage. In many cases the early secondary and intermediate autogenous mills have now been replaced by conventional ball mills and rod mill-ball mill circuits, with the object of further increasing grinding capacity. The third stage to develop is designated as wet primary autogenous grinding, in which run-of-mine ore or a primary crusher product is all fed to the autogenous mill together. It developed many years later indepen¬dently in the United States and in South Africa. The fourth and most recent stage is that of dry primary autogenous grinding, which developed in the United States and Canada. All four stages originated in gold mining. The first use of commercial autogenous grinding outside of the Rand apparently took place five years later in 1912 at the Santa Gertrudis gold mine at Pachuca, 55 miles northeast of Mexico City. This was followed closely by an installation at Goldfields, Nevada, in 1914-1915. The first name associated with autogenous grinding

Jan 1, 1985

By S. C. Howell

The mining of taconite, to provide feed for a processing plant, requires that the flow of material continue uninterrupted. This means first, that the crude must be of a size acceptable to the primary crusher in order to reduce the delays caused by plugging the crusher with chunks. Secondly, elimination of oversize in the pit will reduce costs of all wear parts used in the mining and processing of taconite. Savings in wear parts is readily recognized in dipper teeth, bases, buckets, truck boxes, and crusher parts, both primary and secondary. During the early days of taconite mining, it was soon recognized at reserve mining company's Babbitt operations that experience in mining other ores was not always (or ?necessarily??) Applicable to excavating taconite. This was especially true in drilling and blasting. Blasting of small tonnages in single or double rows simply filled the pit with scattered chunks and provided very shallow banks for shovel loading. It also created problems for the jet piercers, since all drilling had to be performed in fractured areas. Drilling efficiency suffered and costs were extremely high. Shovel and truck efficiencies were also low and again costs were high. A high percentage of secondary breakage was required. This necessitated the use of numerous man hours to jackhammer holes in chunks, preparatory to loading and blasting. After the chunks were reduced, bull- dozer and grader hours were needed to pile the taconite for acceptable shovel loading.

Jan 1, 1968

By Thomas P. Meloy

The understanding, quantification and use of locked particles. Specifically discussed is the use of Textural Transforms (Meloy, 1991) for the implementation of the Interfacial Area Conservation hypothesis (Meloy, 1984); the quantification of the locked particles as a function of fragment to inclusion size ratio; and the selection of set points.

Jan 1, 1991

By Bruce C. Trent

In order to effectively model subsidence caused by underground openings, a two-dimensional computer code has been developed which couples near- and far-field response. The near-field is simulated by a discrete element block code and a finite difference code represents the continuum region in the far-field. The explicit equations allow rapid and inexpensive solutions to geometries which may lead to subsidence. Two sample problems are presented which illustrate the important features of the code.

Jan 1, 1979

By Lawrence P. Bonicatto

The steel industry's increased demand for higher grade pellets has caused the pellet producers to investigate methods of upgrading their product. The Hanna Mining Company's Groveland plant is no exception. The Groveland Mine is located in Dickinson County on the Upper Peninsula of Michigan. The low grade iron deposit is a complex mixture of magnetite and hematite with chert, quartz, jasper, and various iron silicates. (1) Beneficiation is by Humphrey spirals and anionic flotation of the iron minerals. (2) A general flowsheet is shown in Figure 1. Flotation of the spiral tailings makes up about 75% of the concentrate. A minor amount of concentrate, less than 3%, is produced in magnetic circuits. The concentrate is pelletized at the rate of 1.6 million tons per year.

Jan 1, 1968

By Daniel T. Hegyan

The employment of continuous rotary vacuum disc filters to filter refuse from the fine coal washing circuits has been increasing as it has become more important to close the water circuits and eliminate sludge holding ponds. This paper will discuss our past experience filtering refuse, effects of solids concentration in the filter feed, use of polymer flocculation aids, effect of flocculation devices, and effects of particle size and ash content on the filtration rate. Detailed tests were performed on existing installations utilizing coal refuse filters to determine optimum flocculant dosage, solids concentration, and disc rotation speed to form a dischargeable cake. Information was also obtained showing effect of flocculant addition on the moisture of the filter cake. Our test work has shown that the continuous filtration dry cake rates for fine coal refuse correlates very well with the data developed and presented by Silverblatt and Dahlstrom1 except that the curves have moved up the scale by use of polymer flocculant additions. These polymers were not available at that writing. Finally, our tests also confirmed the general premise stated by S. K. Mishra2 that controlled additions of polymer flocculants will reduce filter refuse cake moistures somewhat.

Jan 1, 1974

By Esko O. Nermes

Outokumpu flash smelting of copper concentrates was introduced in 1949 and flash smelting of nickel concentrates in 1959, both at Harjavalta in southwest Finland. The first flash smelter outside Finland was started up in 1956 in Ashio, Japan. Between 1956 and the present about 25 flash smelters for copper, and nickel concentrates have been put into operation in different parts of the world. Outokumpu"s research organization has been highly involved in the development of flash smelting. For example, a direct blister flash smelting process was developed in 1975 and introduced in Glogów, Poland, in 1978, and another has been designed for Zaire. This straight metal process is based on low iron content of the concentrate, which reduces the amount of recycling slag copper. Additionally, the concentrates are rather low in impurities.

Jan 1, 1982

By Warren N. Warhol

The mutual growth of the rare earth industry and the Mountain Pass Operations was no coincidence. It was the commercial availability of rare earths on a scale first made possible by the capacity of the Mountain Pass Operations that spurred research and development efforts toward new applications for rare earths. The first important demand on Mountain Pass was europium oxide for the activation of red phosphor for color television tubes in 1964. Since that time, other rare earths have become even more important, and Molycorp is continuing to supply an ever widening variety of rare earth concentrates and compounds. We enjoy saying that rare earths are not really rare, and that they are not earths, either. Of course, we are talking about the 15 metallic elements with atomic numbers 57-71, called the lanthanides, which occur in nature always together in very similar proportions. Their scarcity can be gauged by the fact that there is more cerium in the earth's crust than there is tin, and more europium than cadmium. The word "earths" comes from the early chemical term for oxide. The rare earths were discovered as oxides, and the term has persisted.

Jan 1, 1980