Search Documents

By R. E. Mussler

As part of an overall goal to develop technology that can maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines is evaluating a method for selectively extracting nickel and cobalt from low-grade domestic laterites. The method involves electrowinning to recover the metals in pure form; therefore, preliminary laboratory-scale electrowinning tests were conducted in both a nondiaphragm and a diaphragm cell to determine the effect of variables on energy efficiency under controlled conditions. Electrolytes were generally reagent-grade sulfate solutions that were prepared to simulate electrolyte that could be obtained by stripping nickel-and cobalt-rich solvent extraction reagents. Limited tests were conducted with electrolyte generated from laterite leach solutions. Electrical energy consumption in a nondiaphragm cell was 2.06 kwhr/lb Ni with the cell operated at 50° C, a cell feed of 90 g/l Ni, a pH of 3.5, an extraction of 3.2 g/l, and a cathode current density of 20 amp/ft2. The energy requirement decreased with increasing concentration and temperature, and increased with increasing. extraction and current density. At 50° C, energy consumption in the nondiaphragm cell was 21 pct greater than in the diaphragm cell, but it was only 5 pet greater at 65° C. For this reason and because of overall cost considerations, operation at 65° C with the nondiaphragm cell was preferred. Smooth sheets of cobalt were obtained by electrowinning in a nondiaphragm cell at selected temperatures from 50° to 85° C and with cobalt concentrations from 55 to 87 g/l. The energy consumption (1.48 kwhr/lb) was 22 pet lower with a cobalt concentration of 75 g/l and a cell temperature of 65° C than with a cobalt concentration of 55 g/l and a cell temperature of 50° C.

Jan 1, 1981

The National Institute for Occupational Safety and Health (NIOSH) National Personal Protec-tive Technology Laboratory (NPPTL) and the Mine Safety and Health Administration (MSHA) conduct a Long Term Field Evaluation (LTFE) program to evaluate deployed self-contained self-rescuers (SCSRs). The objective of the program is to evaluate how well SCSRs endure the under-ground coal mining environment with regard to both physical damage and aging when they are deployed in accordance with Federal regulations (30 CFR 75.1714). This report presents ?ndings of the combined eighth and ninth phases of the LTFE. For these phases, over four hundred SCSRs were evaluated. The units tested include the CSE SR-100, Draeger Oxy K-Plus, MSA Life-saver 60, and the OCENCO EBA 6.5. The OCENCO M-20 was evaluated only in Phase 9. Testing was per-formed between December 2000 and April 2004. Results of the evaluation indicate that all SCSRs experience some performance degradation due to the mining environment. Observed degrada-tion varies from elevated levels of carbon dioxide, high breathing resistance, and reduced capacity. Mechanical degradation to the SCSR components included breathing hoses, chemical beds, outer cases and seals. The LTFE tests discussed in this report are different from tests performed for SCSR certi?cation to the requirements of 42 Code of Federal Regulations, Part 84 (42 CFR, Part 84). LTFE tests reported here are conducted to an end point, oxygen depletion, to enable comparison of the duration of new and deployed SCSRs. The method for obtaining deployed SCSRs for this evalua-tion was not a random selection from the deployed population of SCSRs. Although the results of these tests are useful for observing performance of the tested SCSRs, they are not representative of all deployed SCSRs. A new evaluation protocol, with revised sampling strategies, test methods, and reporting procedures, is currently being designed to enhance the generalizability of the results. This program will be implemented following completion of Phase 10 of the current LTFE protocol.

Jan 10, 2006

By George S. Koch

The distribution of gold in part of the Getchell mine, Humboldt County, Nev., is presented through the statistical analysis of 956 assays of rock cuttings from wagon-drill holes. Two methods to predict grade in undeveloped parts of the ore body are evaluated, and the possibility of sampling bias is tested. The distribution of gold is compared with that in three other Nevada gold deposits of the same type characterized by gold particles mostly of submicron size associated with carbonaceous rocks, and also with that in deposits with coarse-grained gold. Usually, fewer samples of a given type are required to make a satisfactory grade estimate for submicron deposits than for coarse-grained deposits. The economic consequence is that submicron gold deposits are likely to be less expensive to sample and evaluate than coarse-grained deposits.

Jan 1, 1970

By B. P. Martinez

This report presents the results of a research and development program in recovering waste-rolling oils conducted by the Bethlehem Steel Co., before 1954 at its Sparrows Point plant, Sparrow Point, Md., with the cooperation of the Bureau of Mines, U. S. Department of the Interior, College Park, Md. The objective of the program was twofold: First, to recover oil for reuse in the plant; and second, to stop pollution, by oil, of the stream and harbor areas in the immediate vicinity of the plant. The sequence of the investigations was laboratory and pilot plant studies on sedimentation, simple aeration, and flotation for the separation of oil and water; and construction of a production unit using standard flotation equipment. This work was only preliminary for the Bethlehem Steel Co. and it has continued research on this problem. Recent progress indicates that new, improved processes will soon replace the flotation units described in this report. The first efforts to separate oil and water by simple sedimentation were unsuccessful. To establish the cause of this failure, microscope examinations and measurements were made on cold-reduction rolling mill cooling-water effluents containing oil in suspension. It was discovered that an average oil globule, held in suspension, was only 0.001 inch in diameter and would not coagulate with other globules for normal sedimentation at room temperature. The next step in the sequence of studies was to coagulate the oil suspension by simple aeration with air under slight pressure. The aeration methods studied were effective in removing up to 68 percent of the total oil but were approaching flotation in principle. The final investigation of the series was flotation of the oil in conventional laboratory-size flotation cells. The small-bubble method, without reagents, floated up to 89 percent of the total oil held in suspension and was the process selected for pilot-plant development.

Jan 1, 1959

By R. A. Keaens, L. C. IlsLey

For the purpose of this paper a junction box is defined as " a fused switch, inclosed in an explosion-proof compartment, provided with a ready means of connecting or disconnecting a trailing cable without exterior arcing." Junction boxes are intended for use 'at the end of trailing cables and are usually placed outby the last open break through in a coal mine. Where it is not safe to supply current through nips or a trolley, junction boxes suitably spaced along an entry permit tramming and movement of machines with safety, although not with any considerable speed. Junction boxes serve a threefold purpose: (1) They prevent dangerous arcing at the outby end of trailing cables; (2) they afford a safe, practical means of fusing or otherwise protecting the trailing cable; and (3) they provide an efficient means of transmitting power from the power circuit to the trailing cable. The first purpose is the most important from a safety standpoint. Dangerous arcing-that is, arcing capable of igniting gas-frequently takes place where trailing cab1c.s are attached to the power circuit. At either 250 or 500 volts only a very small arc is required to ignite mine gas. The usual method of connecting the trailing cable to the power circuit by cable nips or trolley taps does not make a good electrical connection; hence arcing may be expected at any time. Furthermore, junction boxes eliminate the personal hazard attendant upon the use of trolley taps by removing the possibility of accidental contact with trolley hooks or wire and the liability to injury due to manipulation of the device. In the general scheme of mine ventilation it is assumed that gas will not accumulate where junction boxes are placed, an assumption based on the normal operation of the ventilating system. In many

Jan 1, 1929

By Seth C. Schaefer

[As part of the Bureau of Mines effort to provide thermodynamic data for advancement of mineral resources technology, the standard Gibbs energies of formation (?G°f) of MnS (manganese sulfide) and Fe0.9 S (pyrrhotite) were investigated with a high-temperature galvanic cell employing stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnS, MnO, S02 (g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt with the overall cell reaction MnS (s) + 1.5 02 (g, 0.0114 atm) = MnO (s) + S02 (g) . (1) These results give the standard Gibbs energy of formation of MnS for the reaction Mn (s) + 0.552 (g) = MnS (s) (2) ?G°f = -66.487 + 15.19 x 10-3T±0.207 kcal/mole (896.4 - 1,208.1 K) (3) where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, FeO .9S, Fe304 , S02 (g, 1 atm) //Zr02//02 (g, 0.0114 atm) , Pt with the overall cell reaction 10/3 FeO .9 S (s) + 16/3 02 (g, 0.0114 atm) = Fe.,04 (s) +10/3 S02 (g). (4) These results yield the standard Gibbs energy of formation for the reaction 0.9 Fe (s) + 0.5 S2 (g) = Fe0.9 S (s) (5) ?G°f = -35.229 + 12.67 x 1073T+-0.104 kcal/mole (839.5 - 1,086.6 K). (6) A third-law analysis of MnS data yields a standard enthalpy of formation (AH°f) for the reaction Mn (s) + S (rh) = MnS (s) (7) ?H°f298 = -51.16±0.21 kcal/mole (8) A similar third-law analysis for Fe0.9S data yields a ?29°f298 for the reaction 0.9 Fe(s) + S(rh) = FeO .9S(s) (9) ?HO\°f298 = -24.01±_0.15 kcal/mole. (10) ]

Jan 1, 1980

Develop improved blasting practices that can help to curb overbreak in highwalls at surface mines, thereby reducing the hazards of rock-falls to workers and equipment, The Problem The serious hazard in surface mining is the falling of rock from highwalls. Poor highwall stability is caused in part by geologic conditions, but often is aggravated by faulty blasting practices, where the explosive energy not only fractures the rock to be excavated, but also damages the rock that borders the excavation. This reduces the general stability of the hlghwall and increases the rockfall potential. The probability of injury to mine workers or damage to equipment associated with exposure to the highwall increases with the height of the highwall and the extent of its overbreakage. Most rockfalls occur in the first 15 days after a new highwall is exposed. This statistic is significant since most of the work below a highwall is done during this period. The area of greatest hazard is within 25 ft of the toe for rocks that fall vertically, and up to 90 ft from the toe for falling rocks that are deflected by the highwall during their descent, The workers most frequently involved in such accidents are dozer operators, ground laborers, and shovel operators or oilers.

Jan 1, 1985

By Glenn C. Reed

"Preliminary examination of the Glass Buttes mercury deposits, Lake County, Oregon, was made in August 1945 at the request of W. S. Lazier, present lessee of the deposit.Most of the prospect openings in the area were inspected. The more significant workings were sampled and napped in detail. This report presents the data obtained from the investigation to date.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. noon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. P. S. Dean, assistant director.Special acknowledgment is due to S. H. Lorain, chief, Albany Division, Mining Branch and to S. R. Zimmerley, chief, Salt Lake City, Utah, Metallurgical Division, for analyses of the ores.The presence of quicksilver in the Glass Buttes district has been known since about 1930. The area immediately north of Middle Butte has been superficially prospected by numerous test pits, trenches, shafts, and short adits, which revealed a number of opalized zones. Many of these opalized zones contain weak to strong concentrations of cinnabar. The area has not boon explored thoroughly; no mercury has been produced from any of its deposits.A block of 48 full-size claims has been located to cover a large part of the area in sections 34 and 3, Tps. 23 and 24 S.,R. 23 E.,W.M. These claims, held by, location are owned by H. S. Miller, lumberman of Bend, Ore. W. S. Lazier, 10N. W. 20th Avenue, Portland, Ore., currently controls the property under,a nominal leasing agreement. J. W. McDaniel, 44 Lake Place, Bend, Ore., has done much of the underground and surface exploration on the property.The Glass Buttes district is an area of low relief in the Deschutes River drainage system near the northeast corner of Lake County, Ore. (See fig. 1.) The arid climate is marked by extremes of winter and summer temperature. Water for cane use is not available in the immediate area. Well water, however, can be obtained in limited supply on ranch property 5 miles to the south."

Aug 1, 1946

Background Carbon monoxide (CO) is an odorless, colorless gas that can cause illness and death by asphyxiation. Although the toxicity of CO is understood, CO exposure can occur from unrecognized sources. On April 2, 2000, a couple and their newborn infant were poisoned by CO migrating through the ground from blasting at a nearby coal strip mine into their home near Kittanning, Armstrong County, PA. They were treated at the hospital and diagnosed with CO poisoning. The infant had a carboxyhemoglobin level of 31%, the father 28%, and the mother 17%. Carboxyhemoglobin is the compound formed in the blood when CO is breathed. Persons not exposed to CO have carboxyhemoglobin levels of 0.3%-0.7%, and cigarette smokers have levels of up to 9%. Following release from the hospital, the family installed a CO detector in the basement of their home with the help of the local fire department. This Technology News briefly describes this incident to help increase awareness of the problem. It is discussed in more detail by Eltschlager et al. [2001]. Figure 1 shows the coal strip mine believed to have generated the CO. The initial suspect for the source of the CO was the furnace in the house. Only later did it become apparent that blasting at the nearby strip mine might be the culprit. A State investigation concluded that CO had migrated approximately 500ft from the blast, through the ground, and into the home. Figure 2 shows the locations and order of blasts at the mine. Initially, the mine did not plan to blast. Overburden generally consisted of weathered shale that could be dug without blasting. However, the mine decided to blast when hard sandstone that could not be dug out was encountered within 3 ft of the coal top. The blasting was intended to break up the sandstone. Blasting was done using bulk ammonium nitrate-fuel oil (ANFO) in 6.25-in holes 25-30 ft deep on a 16-ft by 16-ft pattern, with charge weights ranging from 17 to 170 lb. The closest blast to the home was 430 ft on April 17, 2000. The distance from the home to the blast area on the day when CO was first reported (March 31, 2000) was 500 ft. Twenty blasts were detonated at the mine between March 7, 2000, and April 20,2000. The blaster was careful to prevent fly rock since another home was only 150 ft away and a garage was 50 ft away. The quantity of explosive used in the blasts was sufficient to break the sandstone, but was less than would normally be used to blast overburden. The holes were typically one-third explosive and two-thirds stemming, with powder factors averaging 0.43 lb/yd3. Additionally, the muck was not immediately excavated after each blast. The heavy confinement on the explosive acted to prevent the typical release of blasting fumes into the atmosphere. Instances of CO migrating from blasts into homes have occurred before, but generally the distances involved were under 150 ft. It is believed that the blast design contributed to the confinement of CO in the ground, and discontinuities in the ground strata facilitated migration toward the residence. Upon inspection of the blast pitwall, a regular system of joints was observed. These joints are oriented roughly from the blast pit toward the house (figures 3-4).Blast-generated CO appears to have been driven into the joint system, displacing the air. When the joint system was saturated, the next succeeding blast pushed the CO into an uncased well next to the house (a high level of CO has been measured in the well shortly after a blast). From there, the CO entered the French drain system and then the basement of the house. The joints are vertical cracks through rock layers that occur on a regular spacing (figure 3). They are most common near valley slopes and are caused when valley walls converge as the stream cuts down through the rock layers. Often called hill seams, they roughly parallel the valley walls, but can curve and split, creating a pathway for gas movement (figure 5). These fractures are often encountered when underground mining proceeds close to outcrop. The system of fractures at the Kittanning blast pit was well developed and provided a path for transmission of CO both through the sandstone and up and through the overlying shales. Blasting engineers should be able to distinguish naturally occurring fractures from blast fractures and note the frequency, development, and orientation of the hill seams and their proximity to occupied houses. The limits of transmission of

May 1, 2001

By R. F. Tenney

No detailed information has been published heretofore on the performance of small industrial-type anthracite stokers in building-heating service, apparently because of the difficulty of comparing the performance of one unit with that of another over an entire season's operation. Studies of competitive heating fuels have been similarly handicapped, and attempts to compare fuels are seldom technically sound in this investigation, the performance of a 60-in. Losch4 stoker burning rice-size anthracite in a standard commercial boiler was observed during a 4-month winter-spring season. It was used to heat two buildings at the Bureau of Mines' Anthracite Research Center at Schuylkill Haven, Pa., with the customary type of automatic pressure-range control. Attendance was limited to inspecting, fuel weighing, data recording, and ash removal. Results were computed daily and grouped by weekly periods to minimize daily irregularities. The same stoker-boiler unit had already been tested in a series of American Society of Mechanical Engineers (ASME) test code runs, with the stoker running continuously and with other conditions well stabilized A comparison of results from the code test and the building-heating tests provided information not available in the past for a single stoker unit, assisted in analyzing heat losses not computable in a cyclic operation, and established a basis for evaluating stoker performance in heating service.

Jan 1, 1963

By F. C. Gregory

"The ""safety bonus"" in metal mining is a sum in addition to the regular wage, paid to foremen or bosses for keeping the accident rate down to a specified minimum. It has been used with success for some time by certain companies as a regular part of their safety work. It is desirable from the employer's point of view in that the desired results in accident reduction must be accomplished before the bonus is earned; and from the standpoint of the recipient, in that he receives a reward for the additional effort which he has put forth in order to earn the bonus.While this paper relates to the safety bonus as applied in the metal mining industry, the bonus system discussed herein will apply equal well to coal mining, oil-field work, and other mineral industries.Various estimates have been made as to the percentage of accidents that can be prevented through physical safeguards, adoption of safe working methods, and other safety measures which can be initiated and carried out wholly through the management or the safety department. This percentage will always be a vari¬able according to the local plant and conditions. But all who have been engaged in accident prevention agree that such work alone cannot bring the accident fre¬quency down to where it should be, and that it is very necessary to work directly with the workmen, in an effort to make each individual do his share in making the work safe. In this latter phase of the work, the boss who has immediate super¬vision of the men is the one who can do the most, since he is in daily and frequent contact with the men while they are at work. In the metal mines, the shift and stope bosses are the key men; in the oil fields, the ""tool-pushers"" or sub-foremen, and the same applies to all industries. So it becomes necessary to keep these sub-foremen constantly interested in accident prevention, both because they are in personal touch with the men and because they are responsible for production and hostile to any plan which they think will interfere with their output. In large organizations it is the shift boss who represents the company and its policies to the man on the job."

Jun 1, 1924

Maintain good blowing face ventilation while taking deeper cuts with a radio-remote, scrubber-equipped miner. Approach A six week in-mine study of face ventilation effectiveness was made by comparing the existing MSHA-approved blowing curtain setback distance of 25 ft with brattice set back distances of up to 50 ft. Effectiveness was determined by measuring methane levels at the face and in the immediate return. How It Works Blowing ventilation systems are commonly used in mines because the high velocity air stream created by these systems rapidly mixes with and dissipates methane generated during the cutting of coal. A drawback to blowing ventilation is that the work area is placed in return air and this may create dust compliance problems for the shuttle car and mining machine operator. To clean dust from the return a number of mining machine manufacturers supply dust scrubbers built into the machine. Dust-laden air is drawn into ducting at the front of the mining machine's boom and is ducted to a scrubbing unit located on the machine's main frame. The clean air from the scrubber is discharged as a high velocity jet toward the return, generally from the left fender of the mining machine. When taking cuts deeper than 20 to 25 ft with a scrubber-equipped machine, the machine's discharge is in by the mouth of the blowing curtain, creating a concern by mine workers that a loss of air to the face could result. However, Bureau of Mines research found that the push or throw of air toward the return by the scrubber discharge jet allows good face ventilation to be maintained with extended curtain setbacks.

Jan 1, 1984

By Harry W. Campbell

U.S. Bureau of Mines investigation; identified no mineral resources or evidence of mining activity in the Sheep Divide RARE II area. A deposit 10 mi (16 km) southwest of the area contains copper and silver minerals in the Triassic Wild Sheep Creek Formation which probably underlies basalt lava flows covering the study area. Abundant basalt in the area can be crushed and used as aggregate, but suitable deposits closer to markets are widely available No sand, gravel, coal, oil, gas, or geothermal resource, were Identified. INTRODUCTION Location and Access The Sheep Divide RARE II area [10 mi (16 km) west of the Snake River] encompasses 7,100 acres (2,800 ha) of the Hells Canyon National Recreation Area in the Wallowa-Whitman National Forest. Enterprise, Oregon, is located 23 air mi (37 (m) west of the area. Peripheral access is provided by the highway from Joseph to the community of Imnaha, Oregon, then south to the study area by the graveled Upper Imnaha Road (fig. 1).

Jan 1, 1983

By Donald P. Schlick

This report presents a representative cross section of methods successfully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

Detect hazards associated with abandoned mine openings through the use of integrated geophysical technology. Background Many abandoned mines in the U.S. present hazards to the public. The first step in abatement of these hazards usually requires locating the abandoned workings. Recent Colorado legislation resulted in a concerted effort aimed at mitigating the hazards associated with abandoned mine workings. The Colorado Department of Natural Resources-Mine Land Reclamation Division (CDNRMLRD) is responsible for locating and backfilling abandoned mine openings such as shafts, adits and collapsed features. Many shafts and adits can be located by inspection, other openings give little or no surface expression and must be located by drilling, or through the use of geophysical methods. A common method used for locating underground mine workings is to drill throughout the suspected area. However, it is prohibitively expensive to drill holes at the spacing needed to detect backlilled shafts and small voids associated with caving and/or chimneying. It may also be dangerous to move heavy equipment over shallow mined-out workings. Geophysical investigations that employ only a single method have had mixed success in detecting hazardous abandoned mine land cavities.

Jan 1, 1991

By Richard J. Kline

This publication comprises tables listing friction loss for a flexible, spiral-reinforced circular ventilation tubing system. The tables were constructed with the following parameters: a friction factor of 62 X 10-10, 10-foot sections of tubing ranging in total length from 100 to 550 feet, air quantities ranging from 1,000 to 15,000 cfm, and one to four 90° bends in the tubing. The aim of this publication is to improve ventilation tubing analysis and to provide a method of proper fan selection.

Jan 1, 1971

By R. V. Ramani, C. B. Manula, A. Owili-Eger

MINE PROTOTYPE The prototype chosen for application demonstration is from Kingery (1960). The mine and the ventilation plan is presented in Figure 11. A new coal mine is projected with entrance by slope 1,500 feet long. Nine train entries will be standard for development, five as intake and four as return. One return shaft is planned near the slope bottom. The slope will have an area of 150 square feet and a perimeter of 55 feet. The return shaft will be circular with a diameter of 18 feet and will be 500 feet deep. Two hundred feet of the shaft and 500 feet of the slope will be concrete lined. Will it be possible to operate five units per shift with amount of air at each unit not less than 25,000 cfm? Additionally, a shop at the slope bottom will require 10,000 cfm. The problem is completely worked out using standard ventilation formulas and simple manual calculations in the above reference and is reproduced here in Appendix II for ready reference. APPLICATION In this manual, four different applications of the PSU/MVS are outlined. An article by Stefanko et al (1972), outlines how one can move from a mine map to a network for the generation of computer input. Attention is drawn to Figure 12, which is the network line diagram of the mine ventilation system in Figure 11. Note that every roadway junction has been numbered. The dotted lines represent leakage paths and the letter 'R' on a branch denotes that the split is regulated for the quantity shown. For example, there is a leakage

Jan 1, 1975

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By J. J. Bourquin, S. H. Katz

"Three types of respiratory apparatus namely, gas masks, hose masks, and self-contained oxygen-breathing apparatus - are now commonly used for protection from noxious gases, vapors, and smokes or ristes, but no particular type can be selected as best for all conditions. Many factors must be considered in connection with each situation, so that each must be considered as a problem in itself. Following are concise statements for comparing the types:Gas masks are the simplest and easiest to wear, also the least cumber-sore; but they protect only in comparatively low concentrations of noxious gases and should never be used where the air contains less than 16 per cent of oxygen. Special masks give protection from one gas or class of gases, but may give no protection against another gas or class of gases.Hose masks protect in any irrespirable atmosphere, but are somewhat cumbersome, the length of hose limiting the distance a wearer may go from fresh air. They are serviceable also where a supply of pure air moves with the wearer, as where a locomotive engineer in a smoky tunnel is using a hose mask supplied with air from the compressed air line of the locomotive. Hose masks consume no chemicals or materials and so are not limited in the time they may be used.Self-contained oxygen-breathing apparatus protect in any irrespirable atmosphere, but their weight is cumbersome, they can be used only by trained men, and frequent attention must be given them to maintain good working condition. On the other band they are the only safe means for exploring mines and other places filled with irrespirable gases in high concentrations."

Jun 1, 1923

By D. D. Bolstad

This report describes the construction and use of a direct-reading azimuth protractor (DRAP) by the Bureau of Mines for measuring fracture orientations in mines, tunnels, or other excavations having a magnetic environment. The DRAP allows a rapid and simultaneous measurement of dip and azimuth of dip of a fracture plane. The instrument is rugged, lightweight, and easily constructible from standard hardware items. The DRAP can measure dip to within ±0.5° and azimuth of dip to within ±5° of corresponding values obtained with a Brunton compass.

Jan 1, 1974