Search Documents

By Raymond B. Ladoo

The uses of talc are many but are not, in general well known or fully developed within the last decade several companies have realized the possibilities of greatly increased use and have intelligently proceeded to develop some of the fields which seemed most promising. This has had a tendency to lift talc from the obscurity in which it had existed for years, but the work is only started and much remains to be done. Considerably more attention has been paid to the technology and utilization of talc in Germany and Austria than in this country, despite the fact that the United States produces 65 of the world's talc and Germany and Austria combined but 5.4%. In the "Bericht,uber die tatigkeit des verbends der talcum-interessenten in Oesterreich-Ungarn" (Proceedings of the Austro-Hungarian Talc Association), for the years 1912 and 1913, many notes upon new uses appeared, together with suggestions as to further development of old uses. Aside from a few notes on the use of tar in paper, little has been published in the English language upon this subject. By recent action of the Talc and Soapstone Producers Association (U.S.A.) funds for research into the properties and uses of talc have been made Available and it is hoped that markets will be materially broadened a a result of this work.

May 1, 1920

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By Harold L. Rhodes

Vapor-liquid equilibria data for 65-34-1 and 25-27-48 mole percent helium-nitrogen-methane mixtures are presented for 12 temperatures from 76.5° to 164° K and pressures from 100 to 1,200 psia. These data were obtained in a windowed phase equilibria cell equipped with a vapor recirculating pump. Isobaric and isothermal K-values are plotted for both mixtures. Two isometric plots are included.

Jan 1, 1972

By Frank E. Cash

The iron-ore ranges in the Lake Superior district are the liarquette in Michigan, Menominee and Gogebic in Michigan end Wisconsin, and the Vermilion, Mesabi, and Cuvuna in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. Accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year but closely approximate each other over a period of years. During the 4-year period 1940 to 1943, inclusive, 323,667,599 long tons of iron ore was shipped from the Lake Superior district.4/ Michigan and Wisconsin shipped 65,386,608 tons, or 20.2 percent of the total, and employed approximately 15,000 men; Minnesota shipped 258,280,991 tons, or 79.8 percent of the total, and employed approximately 10,000 men. The tons produced per man employed is much, greater in Minnesota than in Michigan and Wisconsin owing to the large open-cut production in Minnesota.

Jan 1, 1945

"While control of dust-related diseases, the objective of the Generic Mineral Technology Center for Respirable Dust, is of prime importance from the human standpoint it is also essential to the economic well-being of the mining industry (FIGURE 23). Although significant progress has been made, the problem continues to be a major concern to the mining community. An increasing global demand for coal and other minerals means that production and the number of miners employed is on the rise. Therefore, the importance of this research to the mining industry cannot be overemphasized.The five areas of dust research are 1) control of dust generation, 2) dilution, dispersion and collection of dust in mine airways, 3) characterization of dust particles, 4) interaction of dust and lungs, 5) relationship of mine environment, geology, and seam characteristics to dust generation and mobility. Some experimental projects where the research is conducted almost exclusively in the laboratory may still rely on industry for imput. No industrial resources are necessary to the research of the non-experimental projects, for example computer modeling .The remaining research is classified as experimental and these projects do require interaction with industry in varying degrees. Periodic trips to mining sites in Western Pennsylvania, Southern Ohio, and West Virginia are necessary to record measurements or collect samples. Or companies may provide needed samples or equipment to the university for use in the laboratory. On several projects interaction is limited to advice or information supplied to the researcher by industry personnel."

Aug 31, 1989

By Laurance L. Oden

The Bureau of Mines conducted corrosion tests of 18 commercial alloys in H3 P04 -phosphate rock or A1,03 slurry, in 10 pct HF, and in 25 pct H2 SiF6 to simulate three environments anticipated in a Bureau process to extract fluoride values from phosphate rock. Small alloy coupons were rotated in duplicate tests at 4.4 to 21 fps in the slurry at 170° C to determine rates of erosion-corrosion. At 4.4 fps the lowest rates, in mils penetration per year (mpy), were measured for Hastelloy C-276 (<20), Hastelloy B (30), and Inconel 625 (150);the rates increased at 21 fps to 55 mpy, 45 mpy, and 1,000 mpy, respectively. The corrosion rate for all alloys exceeded 40 mpy in either the equilibrium vapor or liquid phases of aqueous solutions containing 10 pct HF or 25 pct H2SiF6 at 100° C. Uniform corrosion in 10 pct HF at 50° C was observed only for Inconel 625 (22 mpy), Hastelloy C-276 (43 mpy), and Illium 98 (17 mpy). Inconel 625 (0.75 mpy), Hastelloy C-276 (1.3 mpy), Illium 98 (1.7 mpy), and Incoloy 825 (0.45 mpy) were attacked uniformly in 25 pct H2SiF6 at 50° C.

Jan 1, 1974

By G. Nuñez, M. A. Pathak, C. F. Stanley

"A 1986 report by the U.S. National Committee on Blomechanlcs (1) describes lung disease as a major national health problem. The report cites three areas that would benefit from a better understanding of the vibratory patterns of the lung. These areas are outlined below.1. In cases of respiratory distress, pressure driven artificial respirators are used. A new technique using high frequency respiration is quite promising, but the pressure distribution in the lung as a function of frequency is not yet known. At these frequencies of 1 to 60 Hz, the lung expands asynchronously (2) and a better understanding of these expansion nonunlformltles could provide valuable Information about the mechanics of high frequency ventilation.2. Listening to the sounds In the lung can yield valuable Information about the state of the lung. To improve the technique, a better understanding of how acoustic waves propagate through the lung is needed.3. The response of the lung as It Is subjected to acoustic excitation, dynamic loading or shock waves is not well understood. A better knowledge of these responees can lead to improved treatment for patients subjected to either explosive pressure waves or car crashes.4. Researchers are measuring the acoustic Impedance of the Iung to detect early states of dysfunction. Sneckenberger and Whitmoyer (3) have reported Impedances obtained at acoustic frequencies up to about 6000 Hz. However, It la not certain which parts of the lung are responding to the acoustic excitation.To Investigate the vibratory characteristics of the lung, excised rat lungs were excited via the trachea with acoustic waves at frequencies up to 6000 Hz. Thie paper describes an Instrumentation system, utlllzlng time-averaged holographic Interferometry, to detect and quantify the response of the lung surface to the acoustic excitation."

Jan 1, 1989

By Edward Cogan

Equilibrium phase diagram studies of zirconium- rare earth metal alloys by the Bureau of Mines at its Albany Metallurgy Research Center prompted the development of a rapid gravimetric method for determining rare earths in zirconium in which the rare earths are absorbed from sulfuric acid solution of the alloy on a cation exchange resin . The sample in 10 percent H2SO4 is introduced into the column , the zirconium is eluted with 10 percent H2SO4 , and the rare earths are eluted with (NH4 )2SO4 solution and precipitated with NH4OH . A tracer technique was employed to determine the efficiency of the procedure . Y203 and europium 154 - 152 (Oak Ridge ) were added to 10 g of zirconium and taken through the entire procedure . Recovery averaged 97.6 percent on 0.002 μg europium in the rare earth fraction . Rare earths were determined in the range 0.10 to 90 percent .

Jan 1, 1964

By D. B. Dow

"In the natural-gas Gasoline industry, the methods used in determining the amount of gasoline in natural gas are many and varied; they include the specific-gravity test, laboratory tests involving absorption, charge in volume of the gas or in the absorption medium, absorption in charcoal with subsequent distillation, compression of the gas which results in the condensation of the gasoline, and the absorption of the gasoline vapors in an absorption oil, from which the gasoline is distilled and measured. Each of these various tests has advantages, and disadvantages. It is however, conceded in the industry that the tests in which the gasoline is obtained and measured as such are the more reliable.This paper deals with certain factors which should be considered in making absorption tests using ""mineral seal oil"" as an absorbent; this method of testing is widely used not only in the field, but in control work in absorption gasoline plants where the gasoline content of the intake and discharge gas is determined daily. In control work it is frequently found that the plant produces more gasoline than the tests show, which gives the plant the appearance of making more gasoline than is actually present in the gas treated, or in other words operating at more than one hundred per cent efficiency. Obviously then, the tests as made in these cases are in error, and in hope of correcting some of these variances, the following factors have been studied at the U. S. Bureau of Mines petroleum station at Bartlesville, Oklahoma."

Aug 1, 1920

By Nicholas Kyriazi

It is of interest to know how to obtain as high an absorption efficiency as possible from a CO2-absorption canister used in closed-circuit breathing apparatus. In this study the Bureau of Mines found that varying the bed depth and the cross-sectional area of a canister changes its absorption characteristics. In tests using four ,1 rectangular, variable-depth canisters with different cross-sectional areas, the Bureau found that, given a constant weight of the chemical absorbent, LiOH, and a constant COa input, the canisters with a greater cross-sectional area reached C02 levels of 0.5 volume-percent in the effluent gas sooner than did the canisters with a greater bed depth. However, resistance to flow through the canister increases with bed depth, and a trade-off is inevitable. It was anticipated that the efficiency of a canister would increase with increasing intergranular air space approaching the tidal volume of the breathing waveform and then level off at some point under 100 percent. This postulation was partially substantiated. Cylindrical and radial canisters were also tested and compared. It appears that shape is not as important a factor in absorption efficiency as bed depth, since neither canister differed significantly from the rectangular canisters with regard to absorption efficiency values.

Jan 1, 1980

By Iam Pou Ng

Combustion aerosols consist mainly of elemental and organic carbon (EC and OC). Since EC strongly absorbs light and thus affects atmospheric visibility and radiation balance, there is great interest in its measurement. To this end, the National Institute for Occupational Safety and Health (NIOSH) published a standard method to determine the mass of EC and OC on filter samples. Another common method of measuring carbon in aerosols is the aethalometer, which uses light extinction to measure "black carbon" or BC, which is considered to approximate EC. A third method sometimes used for estimating carbon in submicron combustion aerosols, is to measure particle size distributions using a scanning mobility particle sizer (SMPS) and calculate mass using the assumptions that the particles are spherical, carbonaceous and of known density. With an eye toward evaluating the use of these methods for measuring carbon in freshly emitted diesel aerosols, the objective of this paper is to compare the results among these methods and to investigate the role of OC when measuring the mass concentration of elemental carbon (or black carbon) in aerosols emitted by a medium-duty Diesel engine. Results indicate that the aethalometer response correlates well with the data from filter samples (R2 = 0.99), with a very slight positive interference at high levels of OC.

Jan 1, 2008

By Erle C. Donaldson

The pendant drop interfacial tensiometer is being used to study interfacial phenomena that influence the production of crude oil. A description of the instrument showing the modification of the cell and cell holder is presented. The modified cell and cell holder allow formation of a precise and reproducible drop size, and the image of the drop is easily alined and focused. Interfacial tension measurements and observations of film formation can be conducted at various temperatures with the jacketed cell.

Jan 1, 1967

By F. W. Hoertel

The effects of certain process variables on the grain size, grain type, and microhardness of vapor-deposited tungsten were established, and the near-optimum parameters and the efficacy for the vapor deposition process were determined. No significant change in the grain size or microstructure resulted from ultrasonic vibration of the substrate during deposition, from variations in the hydrogen (H2) to tungsten hexafluoride (WF6) ratio, or from small increases in reaction-chamber pressure. Near-optimum conditions were continuous deposition at atmospheric pressure, a deposition rate of 2-mils thickness/square inch of substrate area/hour, a temperature of 5500 C, and a hydrogen to WF6 ratio of 4:1. The addition, individually, of about 2 volume-percent of butane, 24 volume-percent of carbon dioxide, or 4 volume-percent of propane to the hydrogen and WF6 mixture produced deposits with the finest grain size for each gas. A corresponding increase in microhardness accompanied the decrease in grain size. The addition of gases did not alter the columnar microstructure found in vapor-deposited tungsten.

Jan 1, 1966

By Kent Volkmer, Mark Sanders, Gregory Krohn, Tyler Blake, Daniel Wick, Barry Beith

This report describes a study designed to evaluate a proposed modification in the cap lamp battery cord intented to reduce the incidence of snagging and catching of the cord. A three phase evaluation as performed comparing a prototype with the standard, currently available cord. First, a "pull test" equipment was run. The second evaluation was a body conformity study. The third evaluation involved subjects performing common tasks in a low seam coal mine simulator. The results of these evaluations clearly demonstrated significant safety advantages of incorporating coiled cord into the design of the cap cord. The coil cord presented less of a snagging hazard, allowed the wearer more time to respond to a snag, and transmitted lower levels of force to the helmet when snagged. The research team recommended that cap lamp cords be commercially developed which incorporate coiled cord at the battery and helmet.

Jan 1, 1980

By K. K. Kelley

"In an earlier consideration of the vapor pressure of iron 3/ it was found necessary to estimate the specific heat of gaseous iron to write satisfactory free-energy-of-vaporization equations for the several forms of iron. That the specific heat of gaseous iron will exceed greatly the classical value of Cp = 4.967 calories per gram-mole per degree is evident from even a cursory Lamination of its spectrum. The two lowest energy states are separated by only 416 cm-1, which is small enough so that the second state is effective, theoretically, at below room temperature. Such phenomena are by no means uncommon, but, while they have been recognized with substances that ordinarily are encountered as gases, classical gaseous specific--heat values still are used, often without question, for the vapors of metals and other elements that are solids under ordinary conditions. The following calculations for iron and copper gases are presented to illustrate the sort of deviations from classical values that are encountered with metal gases.The methods employed in calculating from spectroscopic data of thermodynamic quantities such as specific heat, entropy, and free energy have been described, in detail by Giauque 4/ and others. These will be briefly reviewed here. It is customary to separate the translational energy of a molecule from the rotational, vibrational, and electronic energies. In the case of monatomic gases, only translational and electronic Energies are involved. The classical expression for the specific heat of a mona¬tomic gas, Cp = 4.967, deals only with energy stored in the molecule as translational energy and consequently is valid only in temperature ranges in which no appreciable number of molecules undergoes a change in electronic state."

May 1, 1937

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1984 identified no mineral resources or prospects with mineral development potential in the Pit River Canyon Wilderness Study Area (WSA). Basalt suitable for aggregate and fill is in the WSA but rock of this nature is abundant in the region and closer to potential markets.

Jan 1, 1984

By Jeffrey M. Listak

The Respiratory Hazards Control Branch of NIOSH routinely conducts laboratory and mine-site evaluations of dust control technologies. Gravimetric and instantaneous dust sampling instruments are used in these evaluations to measure and document dust levels to determine worker exposure. The Thermo personal DataRam (pDR) is an instantaneous sampler that uses light-scattering technology to provide relative measures of airborne respirable dust. The pDR can be used in active and passive modes to measure respirable dust levels. Tests were conducted to evaluate the sampling performance of active and passive pDR operation relative to each other and. against a gravimetric sampler (the accepted standard for respirable dust measurement). The purpose of the test was to determine if the pDR can be used effectively in the passive mode in higher velocity airflows (up to 5.1 m/s (1000 fpm)). Studies of the pDRs in both modes of operation were conducted in a controlled laboratory environment and in field situations. Dust measurements using pDR units in both modes of operation were recorded in ve¬locities ranging from 1.0 to 5.1 m/s (200 to 1000 fpm). Tests were conducted in ambi¬ent air and in air with the addition of moisture. Results show that, although the units measure different concentrations in their respective modes of operation as compared to a gravimetric sample, the relative readings can be corrected to yield accurate dust measurements.

Jan 1, 2007

By D. J. Bauer

A pure scandium solution was concentrated from 10-4 mole per liter to 0.5 mole per liter by continuous foam fractionation in a spaced, packed column. Recovery in the foam was 77 percent using a spaced, packed draining column with sodium n-methyl-n-"coconut oil acid" taurate as the surfactant. The technique was first studied batchwise in a small unpacked column to determine the more important variables. Optimum surfactant concentration was found to depend on scandium concentration. Extraction and, in general, enrichment ratios were highest in the 2.5 to 3.5 pH range at temperatures ranging from 50° to 70° C. An airflow rate of 136 ml./min. was satisfactory in the equipment used.

Jan 1, 1962

By H. L. Riley, B. W. Gandrud

"INTRODUCTION AND SUMMARYIn connection with a program of research work on coal at its Southern Experiment Station, the Bureau of Mines, in cooperation with the University of Alabama, conducts washability studies of samples of coal from coal fields in Alabama and other Southern States in which commercially important deposits of coal occur. The first such study on coal from a bed in the Arkansas field has been completed, and the results are presented in this report.One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield a good grade of coking coal with a minimum of losses of coal in the rejects.The coal on which this report is based was obtained by underground and tipple sampling at the quality mine of the Quality Excelsior Coal Co. about 3 miles east of Hackett, Ark. This mine operates in the Upper Hartshorne bed, which, as the main source of coal in what is known as the Hackett-Excelsior district, yields an excellent grade of low-volatile coking coal, which is marketed at steel plants in Colorado and California. Production from this bed by the major producers in the Hackett Excelsior district was at the rate of about 125,760 tons annually in 1949, according to the Keystone Coal Buyers Manual. 2/In the laboratory, the tipple sample was crushed to 6-inch top size and screened on a 2-inch round-hole screen. The 2-inch to 0 undersize, amounting to 71.4 percent of the total sample, was fractionated into a series of screen sizes and float-and-sink products to get data for determining the washability characteristics of the coal. Before the screening and float-and-sink tests were made, however, machine cuttings, which are now gobbed underground, were added to the 2-inch to 0 sample. Enough of these cuttings were added so that the resulting mixture was considered representative of what the 2-inch to 0 run-of-mine coal would be if all machine cuttings, including the part now being gobbed, were brought to the tipple as a part of the run-of-mine coal.The mixture obtained referred to in this report as the run-of-mine or raw coal."

Mar 1, 1953

By H. S. Caldwell

This report describes work by the Bureau of Mines on the vacuum distilla¬tion of some of the more volatile metals such as cadmium, zinc, and magnesium from lead and tin. Evacuation within a distillation apparatus allows rapid diffusion of vapor away from the evaporation surface and prevents reaction of the vapor with residual gases. A reduction of pressure to several tenths of a millimeter makes possible practicable distillation rates, at temperatures for which the partial pressure of the metal vapor exceeds 10-3 atmosphere. The rate and selectivity of distillation depend primarily on the volatility and molal ratios of the alloy metals, and their chemical activity to each other. For very rapid evaporation or low concentration of the more volatile constituent, the rate is determined by the rate of diffusion of the evaporating metal, to the surface of the melt. Cadmium, zinc, magnesium, and tellurium were found to volatilize readily from both lead and tin. Tellurium appears to volatilize as an intermetallic compound rather than the pure metal. Antimony could not be removed from lead at 1,000° C.; the condensate was nearly all lead. Antimony, bismuth, and lead were removed from tin.

Jan 1, 1960