Search Documents

By C. L. Chaney

Investigations were conducted to develop spectrochemical methods capable of determining 0.01 to 100 micrograms of metals in 50 milliliters of solution. The use of gallium hydroxide (Ga(OH)3) as a carrier-precipitant to concentrate metallic ions is described. A porous-cup graphite electrode is used to collect the precipitate. A specially designed plunger permits the electrode assembly to serve as the sample-containing electrode in the subsequent spec-trographic analysis. Analytical curves are presented for antimony, arsenic, beryllium, and zinc. Sensitivities of detection are given for 13 elements. The techniques were applied to identify impurities separated from tungsten, to determine trace impurities in solutions containing high concentrations of magnesium, cobalt, or nickel, and to identify trace impurities in hydrofluoric acid. Laboratory glassware was a serious source of contamination when low levels of zinc were determined.

Jan 1, 1963

By W. R. Huff

Yield stress and plastic viscosity values, determined from shear rate-shear stress relationships, were found to be a linear function of coal concentration for coal-water slurries containing 40, 45, 50, and 55 weight-percent of powdered coal. In the laminar region, the flow is described by an equation derived from the fact that the square root of the shear stress varied linearily with the square root of the shear rate. In the turbulent region, the friction factor was found to be inversely proportional to the velocity to the 0.12 power.

Jan 1, 1965

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Liming Yuan

Three-dimensional computational fluid dynamics (CFD) modeling is conducted to simulate spontaneous heating in a large-scale coal chamber with a forced ventilation system. Spontaneous heating is modeled as the low-temperature oxidation of coal using kinetic data obtained from previous laboratory-scale spontaneous heating studies. Heat generated from coal oxidation is dissipated by convection and conduction, while oxygen and oxidation products are transported by convection and diffusion. The water vapor transfer and the effect of heat of wetting are not modeled. The CFD model is validated by comparing simulation results with test results from U.S. Bureau of Mines experiments conducted in the coal chamber. The model predicts lower temperatures in the early stage but agrees well on the induction time for spontaneous heating. The effects of airflow rate and order of reaction on the spontaneous heating process are also examined. The calibrated CFD model is found to be useful for predicting the induction time for spontaneous heating in underground coal mines.

Jan 1, 2009

By LB. Berger

"INTRODUCTION The use of gasoline engines as the motive power for lift trucks, tractors, and other types of mobile equipment operated in enclosed spaces, such as industrial plants and warehouses, may create a hazard because of the carbon monoxide present in the exhaust gases of the engines; gasoline-powered equipment should not be used in mines or tunnels. Because the equipment is mobile, local ventilation usually is impracticable, and general ventilation of the spaces is nec-essary to dilute and remove the carbon monoxide. To estimate the rate of ventilation required in such situations, information is necessary on the concentration of carbon monoxide in the exhaust gas and the rate at which exhaust gas is produced under given operating conditions. The purpose of this paper is to present data that may be used in making estimates of ventilation requirements.COMPOSITION OF GASOLINE-ENGINE EXHAUST GASThe exhaust gas of a gasoline engine consists mainly of carbon dioxide, carbon monoxide, hydrogen, oxygen, and unburned hydrocarbons (usually reported as methane), together with the nitrogen present as a residue from the air sup-plied for combustion. 3/ The exhaust also contains water vapor resulting from combustion of the hydrogen of the fuel. The water-vapor content is not included in exhaust-gas analyses calculated on a ""dry"" basis and is not involved in the estimation of ventilation requirements."

Jun 1, 1947

By Harry G. Dosh

Sillimanite, kyanite, and andalusite are aluminum silicates having the same chemical composition (Al2SiO5) and are used in the ceramics industry for the manufacture of high-grade refractories. Natural sillimanite with added corundum or other alumina to just short of mullite (3Al2O3 -2SiO2) proportions is unequalled for jobs wherein strength at high temperatures, resistance to spalling, and resistance to slagging by acid slags are desired. High-grade porcelain ware also requires these minerals. At the same cost, sillimanite would be preferred for most uses, but the lack of any large source of sillimanite bas given economic preference to kyanite or andalusite for special refractories and high-grade porcelain wares. Sillimanite-bearing schists were observed in Spartanburg County, S. C.; as early as 1937 by D. Hoye Eargle, geologist with the U. S. Soil Conservation Service. The mineral was not identified until 1942, when Miss Jewell Glass, of the U. S. Geological Survey, examined several of the deposits. This identification was confirmed in 1943 by Dr. Laurence L. Smith, of the University of South Carolina, when he examined the Spartanburg County deposits and found numerous additional occurrences of sillimanite schist in Greenville County. Subsequent work by the Bureau of Mines and the South Carolina Geological Survey has been responsible for the location of additional sillimanite-rich schist deposits in Spartanburg County. Between October 1, 1948, and November 21, 1948, the Bureau of Mines conducted an exploratory diamond-drilling project on the John Gideon property in the southeastern section of Spartanburg County (fig. 1) and drilled a total of 681.7 feet in six holes. Drilling indicated that the deposit is relatively shallow, as no ore was cut below the zone of weathering.

Jan 1, 1950

By Jr. Hardy, H. Warren Shen

"A study is presently underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal breakage and cutting procedures. The present paper will focus on the test facilities, experimental techniques, and results associated with linear, single-bit cutting. An AE-transducer, attached directly to the bit, detected AE signals during the cutting process.Experiments have been carried out on seven specimens of coal obtained from the USBM experimental mine at Bruceton, Pennsylvania. Three separate cuts were made for each of two bit angles (10 and 45 degrees) and two bit velocities (0.085 and 0.169 cm/sec), for a total of 12 separate cuts. Data associated with resulting particle size distribution and AE characteristics (major dominant frequency components) will be discussed. Data analysis has also been underway using a computer-based pattern recognition system known as ICEPAK (Intelligent Classifier Engineering Package). This program is able to evaluate over 100 features of an AE event and to make objective comparisons between AE signals associated with different loading or cutting parameters. The results to date show that AE generated during some of the test conditions can be recognized by ICEPAK with a recognition rate of 90% and higher while other conditions cannot at present be separated with a suitable recognition rate. Further analysis of the experimental data is presently underway.The reduction of the severity, and eventual elimination, of Coal Workers' Pneumoconiosis (CWP) depends on gaining fundamental understanding in a number of major areas. These include dust generation and entrainment, transportation, suppression, medical effects of dust, and possible treatment. At present a project is underway by the authors to investigate the character of the bit-coal interaction during coal cutting and its influence on the size and shape distributions of the generated dust. An important aspect of this on-going project is the development of acoustic emission (AE) criteria which would make it possible to carry out remote monitoring of coal cutting operations. Suitable on-line analysis of monitored AE data would allow engineers to evaluate factors such as shearer bit conditions and cutting efficiency, and to quantify the particle size and shape distribution of the generateddust. The on-going AE studies are fundamental in form and were undertaken to evaluate the general feasibility of AE monitoring techniques using simplified coal cutting procedures. To date experiments have been carried out on coal under uniaxial compression, linear single-bit cutting, and cutting using a laboratory-scale, single-bit shearer. A brief outline of the overall study has been presented in an earlier paper (Hardy, Shen and Kimble, 1995). This paper will consider the linear single-bit cutting studies in more detail.It is generally accepted today that most solids emit low-level seismic signals when they are stressed or deformed. In this paper this phenomenon will be referred to as acoustic emission (Hardy 1972, 1981, 1989). In essence, the measurement of AE activity in a field or laboratory structure is relatively simple. A suitable transducer is attached to the structure, the output of the transducer is connected to an associated monitoring system, and the AE signals occurring in the structure, due to internal or external stress, deformation, and failure are suitably acquired, pre¬processed and recorded."

Jan 1, 1998

By C. M. Bouton

Although much valuable work has been done in the study of dust explosions, the laboratory technique has not been developed to the point where the many factors involved can be properly controlled, and thus where really fundamental information can be obtained. This paper presents a brief discussion of the difficulties encountered in fundamental work on dust explosions, a description of apparatus intended, to overcome some of them, and an account of some results obtained. FACTORS INVOLVED IN DUST EXPLOSIONS The more important factors pertaining to the dust cloud itself which are known to determine the phenomena of explosions are (1) the kind of dust; (2) its fineness; (3) its concentration in the exploding cloud; and (4) the nature of the interior motions, or turbulence, of the cloud before and during the explosion. These factors are arranged in what seems to be an ascending order of complexity. The kind of dust is the factor most easily subject to control. The fineness of the dust at first sight seems to be a controllable factor, but when it is recalled [that] most explosible dusts are mixtures of particles of continuously varying sizes so small as to pass through the finest woven sieves, and therefore difficult to separate either for purposes of analysis or experiment, the fineness is seen to be a factor difficult to control accurately.

Jan 1, 1929

By R. V. Ramani, R. Bhaskar

"An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using a shearer or a continuous miner.The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion and inertial impaction, The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size depend,From a review of the literature, there appears to be a knowledge gap in the understanding of the deposition phenomena in mine airways. In order to obtain a better understanding of the deposition of dust for various particle sizes, and to develop a set of data for evaluating predictive mathematical models for dust-flow in mines, a series of dust flow experiments was performed under controlled conditions in mine airways. It appears that the deposition data generally follow the theoretical behavior of dust based on the combined effect of diffusional and gravitational deposition. In this paper, the findings of the study on the deposition of dust in mine airways and its dependence on size, velocity and concentration are discussed. A set of deposition equations that could be used to determine the approximate deposition at various points in a mine airway are presented.The major factor affecting ambient dust concentration in mine airways is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian diffusion, eddy diffusion and inertial impaction. The major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. Inertial impaction is significant only during changes in direction, but the change in direction of flow with resultant powerful eddies may cause increased re-entrainment of the particles, thus having a compensating effect. While the literature in aerosol sciences contain several references on deposition, most studies were done in small diameter tubes for diffusional deposition (Liu and Agarwal, 1974). The deposition data from small diameter, short tube experiments may not be applicable to studying deposition in mine airways that have large areas and extend several hundred meters. Further, the change in concentration along the length of a mine airway may significantly affect the deposition, an aspect that may not be easily determined in short tubes in laboratory experiments."

Mar 1, 1992

By W. E. Miller, G. S. Scott, G. W. Jones

"INTRODUCTION One of the major activities of the Bureau of Mines is the promotion of safety in mining and the mineral industries. Research is undertaken in connection with these problems to determine the explosion and ignition hazards of combustible gases, liquids, and solids and to investigate means of reducing them.Occasionally the Bureau is asked to determine inflammability or ignition temperatures to enhance safety in nonrnineral industries. From time to time it has complied with such requests when no other agency was available to do the work and the investigation could be conducted with a minimum of time and expense. The present investigation is one of this class.Nicotine (C10H14N2), a colorless combustible liquid having a boiling point of 246°C, is usually obtained from tobacco and its products by extraction processes. When heated to its boiling point it decomposes; the purified product is obtained from tobacco extractions by distillation at reduced pressures or is distilled in a current of inert gas.It has an unpleasant odor, a burning taste, and in the undiluted state is highly toxic. Under certain conditions it can be oxidised to nicotinic acid and in the near future may therefore become of considerable economic importance. Nicotinic acid is a component of the vitamin B complex now commonly used to fortify white flour and other foods that normally are deficient in these vitamins."

May 1, 1942

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

By W. E. Wallace, V. Castranova, P. Hathaway, F. H. Y. Green, E. D. Recad, V. Vallyathan, M. J. Keane

Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modeled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiologic saline. Lecithin adsorbs to the dusts upon incubation at 37º C and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defense system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modeled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica hemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin hemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in this same time; that which is results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.

Jun 1, 1988

By Ludwig Schmidt

[The use of vapor-tight tanks has proved so effective in reducing the evaporation losses of petroleum that today practically all operators are using this typo of equipment. It has boon shown, however, that vapor-tight tanks should be supplemented with additional measures which will further reduce evaporation. Probably the most effective use of the supplemental measures are found on the small producing leases where the breathing losses from vapor-tight stock tanks materially affect the volume and gravity of the stored oil. The breathing loss from a vapor-tight stock tank that is filled and emptied daily is a negligible quantity. Also, the filling loss, which on the average varies between 0.1 and 0.2 per cent, usually is not of a sufficient quantity to affect materially the value of the crude. However, the combined breathing and filling losses from a vapor-tight tank requiring several days to fill are of sufficient importance to warrant the use of measures in addition to the vapor-tight tanks. The breathing losses are caused by atmospheric variations. Probably the greatest are the changes in atmospheric temperature which cause changes in temperature of the vapors in the tank. During the day, as the temperature increases, the gasoline-saturated vapors in the tank expand and are forced out into the atmosphere. At night the vapors are cooled and contract, drawing into the tank fresh air, which becomes saturated with gasoline vapor and is forced out of the tank during the following day. In Addition to the maximum and minimums temperature variations there are many smaller variations throughout a twenty-four period caused by showers, clouds, winds, and other atmospheric conditions which likewise cause the tank to breathe. The two mist common measures used by lease operators for reducing breathing losses in vapor-tight tanks are, first, operating; lease tanks under pressure, and second, the use of light colored paints anti tank houses. In this report these two methods are discussed together with their adaptability to lease operation. Results of experimental observations are given which show the reduction of evaporation looses where these supplemental measures have been used.]

Jan 1, 1927

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By R. V. Lundquist

The specific conductance of solutions of sodium hydroxide and of sodium aluminate was directly proportional to the temperature. The specific conductance of sodium aluminate solutions with identical sodium ion concentration and at constant temperature decreased with increase in aluminum concentration. The aluminate ion population in solution was shown to consist of a mixture of monovalent and polyvalent ions. Aluminate ions did not influence the temperature dependence of pH in caustic solutions containing sodium aluminate. The density and viscosity of a solution was inversely proportional to the temperature and directly proportional to the concentrations of sodium and aluminate ions.

Jan 1, 1965

By Thomas M. Barczak

This report describes a study that examined load transfer mechanics in longwall shield supports as part of the Bureau of Mines research program to optimize support design and utilization. The objectives of this study were to determine the contribution of the leg cylinders and the caving shield-lemniscate assembly towards full shield vertical and hor-izontal load resistance capability and to determine how the interaction of these members affect overall shield response. Load-displacement characteristics of the leg cylinders and the caving shield-lemniscate assembly, independent of the full shield, were evaluated from controlled displacement tests in the Bureau's mine roof simulator and responses were compared with full shield responses to identify load transfer mechanics. It is concluded from this research that the participation of the caving shield-lemniscate assembly significantly affects the response of the shield support. It is likely that the caving shield-lemniscate assembly is not participating fully in current shield designs because of translational freedom in the numerous pin joints. It is also concluded that the shield will respond differently to different boundary condi-tions resulting from interaction with the strata. This report describes load transfer mechanics of shield supports and the implication of these research findings on shield design and utilization.

Jan 1, 1988

By Joseph L. Condon

High-speed movies were taken of crater experiments in two-dimensional plates of Tennessee marble to study craters being formed primarily by stress-wave action. The contribution of gas action to the cratering process was minimized because the two-dimensional models did not contain the expanding gases from the explosive. Four burdens were studied for solid plates and one burden for a segmented plate. After cratering, the plates were reassembled for dye penetrant studies of fracturing. Flyrock velocities were calculated and related to the degree of fracturing, and compared with those from quarry shots. In general, the smallest burdens produced the highest flyrock velocities and the least amount of fracturing. Flyrock velocities compared favorably with initial flyrock velocities in quarry blasts, but did not show step accelerations due to gas effects as did the quarry blasts. The test with a segmented plate was used to simulate cratering in a jointed material and showed that stress-wave effects can be important for crater formation in jointed rocks.

Jan 1, 1972

By Deborah A. Spotts

Researchers at the Bureau of Mines have developed a technique for re- generating chromic acid-sulfuric acid etching solutions used in metal surface treatment operations. The technique utilizes a diaphragm cell equipped with a cation-selective membrane to oxidize cr3+ to cr6+ at the anode and to remove copper, the major metallic contaminant, at the cathode. Normally, spent etchant is discarded after approximately 3 days of use. Using the electrolytic cell, the etchant can be used for a year without replacement, From data obtained from industrial-scale cells, the installation of a regeneration cell with a 1,000-gal catholyte- holding tank has been estimated to save at least $240 per day, The payback period for the investment is estimated to be about 10 mo or less. Because the magnitude of these cost savings will vary at different locations, several graphs are presented to aid in calculating payback for a specific site. Using these graphs and the capital costs presented in this study, the payback period can be determined for installing a regeneration cell with a 500- or a 1,000-gal catholyte-holding tank in an existing surface treatment plant.

Jan 1, 1983

By E. D. Regad, W. E. Wallace, V. Vallythan, V. Castranova, P. Hathaway, F. H. Y. Green, M. J. Keane

"Abstract—Inhaled particle contact with pulmonary surfactant in the hypophase lining pulmonary alveoli was modelled in vitro by exposing two respirable sized dusts, kaolin and silica quartz, to lecithin, a major component of pulmonary surfactant, emulsified in physiological saline. Lecithin adsorbs to the dusts upon incubation at 3TC and suppresses their cytotoxicity as measured by pulmonary macrophage and erythrocyte assays, suggesting that pulmonary surfactant provides a defence system against prompt cell membrane lysis by inhaled dusts. Subsequent pulmonary macrophage phagocytosis and lysosomal enzyme digestion of the coated dusts was modelled in vitro by incubation with phospholipase A2 for one hour. With increasing lipase activity, silica haemolytic potential was restored to native silica levels. Kaolin was retoxified to levels far in excess of native kaolin haemolytic potential. Elution, thin layer chromatography and phosphate assay of treated dusts indicate that most lecithin on silica is digested to lysolecithin and desorbed, silica retoxification being due to surface and adherent lysolecithin effects. Most lecithin on kaolin is not digested in the same time; that which is. results in adherent lysolecithin which is responsible for the kaolin retoxification. Digestion with phospholipases A2 and C together produces only weakly retoxified kaolin. Results suggest that surface adsorption properties which control the adherence of prophylactic surfactant distinguish the pathogenic potentials of quartz, kaolin and mixed dust.INTRODUCTIONERYTHROCYTE HAEMOLYSIS and pulmonary macrophage enzyme release assays show quantitatively comparable high cytotoxicities for both silica quartz and kaolin respirable sized dusts (BROWN, et al., 1980; DANIEL and LE BOUFFANT, 1980.) This contrasts with the strong potential for respirable quartz dust to induce pulmonary fibrosis and the much more limited potential of kaolin dust to do the same (MORGAN and SEATON, 1975).In an attempt to understand this anomalous situation, assays were performed on quartz and kaolin dusts incubated with dipalmitoyl lecithin emulsified in physiological saline, to simulate the initial contact of a respired dust with the pulmonary alveolar hypophase. The ability of kaolin dust to adsorb dipalmitoyl lecithin from physiological saline has been quantified (WALLACE, et al., 1975). Such lecithin treatment suppresses the cytotoxicity of both silica and kaolin to background levels (WALLACE, et a1.,1984).Surfactant coated detoxified dusts should then be phagocytised by pulmonary macrophages, incorporated into a macrophage secondary lysosome and exposed to hydrolytic lysosomal enzymes. Among these is phospholipase A2, which hydrolyses diacyl lecithin to lysolecithin. This was modelled by incubating lecithin treated dusts with phospholipase A2 in vitro to determine if the enzyme can digest the dust-adsorbed lecithin, and if the retoxification differs between the two dusts in a manner which might distinguish their pathogenicity."

Jan 1, 1988