Search Documents

By R. Barany

This paper reports determinations of heats of formation (from the oxides and elements) of crystalline cadmium metasilicate and crystalline lead meta-silicate by hydrofluoric acid solution calorimetry. The results, in conjunction with known entropy values, yield free energies of formation. There are no earlier data of this type for cadmium metasilicate. The results of this investigation for lead metasilicate deviate from the literature values (which are less reliable) in the direction of increased thermodynamic stability. Both cadmium and lead metasilicate are much less thermodynamically stable with respect to their constituent oxides than are the corresponding compounds of the alkaline earth metals.

Jan 1, 1959

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines (USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two for-mulations resulted in stable gels that lasted for at least 12 months in the mine. Semicontinuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both in terms of productivity and enhanced mine safety.

Jan 1, 2010

Three -dimensional boundary value problems are difficult to solve. Indeed, while the separation of the scalar wave equation can be effected in 11 different coordinate systems, an analytic solution requires that the boundaries, both external and internal, possess the same symmetry as the coordinate system. Numerical methods are thus of great importance for the solution of such problems; however, despite the availability of high-speed, large memory digital computers , the solution to a significant three -dimensional problem is by no means trivial. It is unfortunate that the results reported here by Jones are invalid. Jones discusses a model in which a three-dimensional island lies off a linear coastline where all the interfaces lie in the coordinate planes in a Cartesian system. A downward plane em wave polarized with the electric field parallel to the linear coastline, and two of the islands coast, is incident downward. This, of course, requires that the incident electric field is perpendicular to the other faces of the idealized Cartesian island. The significant equation used by Jones for his finite difference calculations is [ ] where n2 = sµ? . is the conductivity, µ=µo is the permeability of the appropriate medium, and w is the angular frequency of a Fourier component of the incident field. We see that the displacement current term is omitted, which is an excellent approximation for the parameters of interest in this model. In the similar equation for the y- component of the diffusion equation, the same considerations which we are about to discuss are equally valid. It can be seen from the equation that the field components are related and thus any errors introduced will be propagated into all three components. The difficulty arises when Ex or E is perpendicular Y to one or other of the surfaces of discontinuity in s. The continuity of current at the air-earth interface (upper surface), e. g., jy, requires

Jan 1, 1973

Determine the appropriate spacing and alarm levels for carbon monoxide and smoke sensors used for fire detection in underground coal mine conveyor belt entries. Background Fire represents one of the most severe hazards in underground coal mines. Early-warning fire detection in underground coal mines is essential to successfully implement and execute evacuation and control measures. Both carbon monoxide (CO) and smoke sensors have the ability to provide reliable early-warning capability, provided that they are spaced properly and set at the appropriate alarm levels. The U.S. Bureau of Mines conducted a series of large-scale experiments where a small coal fire was used to ignite a conveyor belt at air velocities of 0.76 to 6.1 m/s. The test configuration was purposely designed to model a worst-case fire scenario for fires that develop within conveyor belt entries in underground coal mines. During the tests, CO and smoke levels were continuously measured to determine alarm times and alarm levels as the fire intensity progressed. The data from these tests indicated that for a given sensor spacing, the time to reach a preset alarm threshold depends upon the belt entry air velocity and cross-sectional area. Analysis of this data resulted in the equations and nomographs for CO and smoke sensor spacing, and alarm levels contained in Bureau of Mines RI 9380, "Fire Detection for Conveyor Belt Entries."

Jan 1, 1993

By Thomas J. Fisher, Thomas Novak

Strong circumstantial evidence suggests that lightning has initiated methane explosions in abandoned and sealed areas of underground coal mines. The Mine Safety and Health Administration (MSHA) investigated several of these occurrences within recent years. The investigated explosions occurred at significant depths, ranging from 500 ft to 1200 ft. Data from the National Lightning Detection Network indicate a definite correlation between the times and locations of the explosions with those of specific lightning strikes. This paper addresses the question, "Can lightning cause potential differences capable of igniting methane-and-air mixtures at overburden depths at which underground coal mining occurs?" A mine depth of 600 ft was selected for this initial study. Computer simulations were performed, with and without the presence of a metal- cased borehole extending from the surface to the mine level. CDEGSTU software from Safe Engineering Services & Technologies, Ltd (SES) was used for the simulation.

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008

By S. J. Page, J. A. Organiscak

Airborne respirable dust surveys were conducted at six surface coal mines to investigate the effectiveness of dust control methods used on rotary rock drills and bulldozers. Dust controls commonly used on drills include a dry dust collection system, exhausting from a shrouded area around the collared hole, and an enclosed drill operator cab, filtering airborne dust from the cab. Bulldozers are also typically equipped with an enclosed operator cab as a dust control measure. Airborne respirable dust sampling was conducted near each equipment's source of generation and inside its enclosed cab. Silica analysis was performed on the dust samples to determine the percent silica content in the dust generated at the six mining operations. An additional eight- month follow-up of dust sampling was also conducted in the enclosed operator cabs of several rock drills and bulldozers. Data were analyzed for long-term variability of accepted control methods to abate dust and silica levels. The highwall rock drill was the major and most variable dust source as compared to the bulldozer, generating dust levels, on average, one order of magnitude higher than dust levels of the bulldozer. Four of the six drills surveyed had dust containment and capture problems at the shrouded drill table above the lple. Repairs or modifications to three of the drill dust collection systems were shown to reduce dust levels by more that 50% next to the shrouded drill table. The enclosed operator cabs provided more than 90% and more than 40% lower dust levels than at the dust source for the drill and bulldozer, respectively. Long-term sampling of several of these highwall drills and bulldozers showed that the dust levels in the drill cabs were frequently higher than 0.2 mg/m3 and more variable than in the bulldozers. The bulldozer dust levels were frequently below 0.2 mg/m). Future research should focus on improving some of the deficiencies present in the drill's primary dust collection system, and developing quality control methods to ensure the integrity of enclosed cab protection for equipment operators.

By Charles D. Litton

Experiments were conducted to determine the optical scattering properties of diesel particulate matter (DPM) and various combustion aerosols from both flaming and smoldering combustion sources at discrete angles of 151 and 301 in the forward direction and at a light source wave length of 635 nm using a simple light scattering module. In addition to the scattering data, simultaneous measurements were made of the total aerosol mass concentration; light extinction at an average wave length of 546nm; and the response of a common bipolar ion chamber typical of residential smoke detectors modified to allow the aerosols to flow through the chamber. The results of these experiments indicate, for DPM and combustion aerosols, the intensities per unit mass concentration depend not only upon whether the aerosolis DPM or combustion aerosol but also upon the type of combustion aerosol. The results also indicate that the ion chamber responses are greatest for DPM, followed by the response to flaming combustion aerosols (FCA)and lowest for smoldering combustion aerosols (SCA). For light scattering, the greatest intensities are found for SCA, followed by the intensities from FCA, and lowest for DPM. This report describes the experiments, their results, and the use of these results to developed sign criteria for early warning fire sensor capable of the rapid and reliable detection of fires in atmospheres that may or may not be contaminated by the products produced from diesel engines. © 2002 Elsevier Science Ltd. All rights reserved.

By Ronald S. Conti

This is the fourth and final article in a series that discusses underground fire-fighting preparedness. As with the previous three articles, it is based on interviews with 214 miners at 7 underground coal mines (referred to as Mines ?A? through ?G?) conducted by researchers of the National Institute for Occupational Safety and Health?s(NIOSH) Pittsburgh Research Center[Vaught et al. 1996]. The first article presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. The second article discussed miners? preparedness to evacuate a fire and their experience with incipient fires. The third article described miners? experiences in fighting underground mine fires and presented their perceptions of training and readiness for fire-fighting. This final article in the series offers suggestions to improve mine fire-fighting preparedness.

Jan 1, 1997

By T. M. Garland

A nomographical approach is proposed as a fast, easy-to-use, and reason- ably accurate method for estimating expected discounted cash flow (DCF) rate of return and payout time for onshore development drilling and oil production. All costs pertaining to drilling, completing, and equipping development wells, annual expenses of operation, maintenance, and taxes incurred in producing properties, and crude oil prices were considered in developing the nomographs. This report briefly outlines the origin, derivation, and use of the nomographs.

Jan 1, 1973

Engineering controls for overburden drilling include dry dust collection systems, wet dust suppression systems, and enclosed cabs [Zimmer and Lueck 1986; Volkwein et al. 1979]. Proper maintenance of the dust suppression system is critically important for drills using dry dust suppression methods. Failure to rigorously maintain these systems will result in inadequate dust control. Acute silicosis has been reported in miners operating equipment that relies on dry dust suppression [NOSH 1992].

Jan 1, 1997

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks' analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By Fred N. Kissell

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

By R. L. Grayson, W. E. Wallace, J. W. Stephens, M. D. Attfield, P. S. Brower, V. Vallyathan, M. J. Keane, J. C. Harrison

Pure respirable quartz is a known pathogenic agent for lung disease. However, for mixed dusts, neither mineralogical nor in vitro cytotoxicity assays unequivocally predict the contribution of quartz to their pathogenic potential.First, although Coal Workers' Pneumoconiosis (CWP) and Progressive Massive Fibrosis (PMF) prevalence have been found to correlate with total respirable coal mine dust exposure, and with coal rank (Attfield and Morring, 1992), epidemiological studies generally have not found the quartz component of coal mine dust as measured by X-ray diffraction or infrared spectroscopy (each of which essentially measures the mass-percent quartz in a bulk sample) to be clear predictors of CWP prevalence or incidence (Walton et al., 1971). Second, the properties which distinguish the extreme fibrogenic potential of quartz are not revealed by conventional in vitro bioassay comparison with other silicate mineral dusts. As an example, quartz and kaolin (aluminosilicate) clay in vitro cytotoxicities are comparable for lavaged primary pulmonary macrophages.The studies discussed here address these two anomalies from a general hypothesis that the pathogenic activity of respired quartz particles is associated with properties of, and interactions with, the particle surfaces. One factor in the expression of toxic activity by a particle surface is the biological availability of that surface. Anomalous lack of correlation of disease prevalence with mass percent quartz in exposures to some mixed composition respirable-sized dusts suggests that individual particle surface features, invisible by bulk sample mass analysis, may alter the biological availability of a fraction of quartz particles in a dust. For pure-surfaced mineral particles, the comparably strong prompt membranolytic activities of quartz and kaolin in vitro suggest that upon deposition of such particles in the lung there must be other interactions with particle surfaces which distinguish quartz. This might be due to toxic surface-associated sites specific to silica, or to interactions of other sites on other mineral particles which affect the biological availability of their toxic functional groups. For example, alurninol groups on clays affect the availability or activity of adjacent silanol groups. Surface activities which distinguish quartz pathogenici ty might be manifest in one or more of the sequential interactions upon deposition in the lung; first with the pulmonary surfactant system, then with extracellular and phagolysosomal enzymatic digestive processes, or with subsequent cytotoxic processes.

Dec 1, 1995

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By R. L. Schmidt

Research conducted over the past 20 years in France, Great Britain, and the United States on the use of the large-hole burn cut has established cer¬tain advantages for this system. Advantages include longer pull and more complete fragmentation from blast rounds. However, research is needed to establish a set of parameters for optimum performance. As part of the Bureau of Mines Advancing Mining Technology for Marginal Resources program, the Twin Cities Mining Research Center, Twin Cities, Minn., acquired a horizontal rotary drill capable of boring holes up to 24 in. in diameter. This was used for a series of underground experiments at White Pine mine, White Pine, Mich., during 1973. Exceptional results were obtained with a 12-1/4-in void hole that yielded up to 18 ft of pull in a 10- by 20-ft drift, Fragmentation was excellent, and the compactness of the muck pile facilitated loading.

Jan 1, 1975

By R. V. Ramani, K. V. K. Prasad, M. Swaminathan

"Engineering design involves, in addition to numerical calculations, considerable amount of expertise and judgement. The expertise and judgement is required to conceptualize and idealize the problem, select a suitable mathematical model for the problem and to interpret the model results in terms of stipulated design constraints. In recent years, knowledge based systems (KBS) have provided the capability to integrate the qualitative experiential and expert knowledge with ~he quantitative knowledge for improved analysis and design of systems. A possible KBS architecture for mine ventilation system design was discussed by Ramani and Prasad · (1987). The expert system (ES) component of the KBS supports the analysis and interpretation phases of the ventilation design process with an algorithmic program used for the solution of alternate designs. The purpose of this paper is to discuss the data and knowledge needs for developing such a system and a formal means of their representation on the computer. A number of ES shells were evaluated to explore possible development and delivery environments for the system. A brief summary of this evaluation is also provided.INTRODUCTIONLuxbacher and Ramani (1979) have discussed the design process of mine ventilation systems and have provided the interrelationships that exist between ventilation, strata control, drainage and material handling systems and mining methods. They have also outlined the importance of correct analysis of the problem, choice of the right solution method and a rigorous interpretation of the solutions. The expertise required for analysis and interpretation phases was identified as the key element in developing effective and efficient ventilation system designs. Such expertise is embedded in the right choice of questions to be asked of the user as well as in directing the user to a wide array of alternative methods that may satisfy the design requirements. With advances in artificial intelligence applications in recent years, particularly expert systems, the integration of expertise into traditional mine planning and design algorithms has been facilitated. These planning and design aids, employing the integration of numeric and symbolic logic and called coupled systems, are powerful tools for engineers to tap the benefits of experts (Kitzmiller and Kowalik, 1985; Fenves, 1985). The purpose of this paper is to discuss the means of representing knowledge for the design of mine ventilation systems through the use of a coupled system. The KBS is visualized as consisting of the following components:"

Jan 1, 1989

By Donald P. Schlick

This report presents a representative cross section of methods success- fully used to ventilate continuous-miner places as well as various factors that should be considered when selecting auxiliary ventilating equipment. Line brattice can direct fresh air to the active face reasonably well, provided that adequate area for installation is available. Continuous mining equipment, however, often restricts clearances to such an extent that proper installation of line brattice is impossible. Consequently, in many instances face ventilation is inadequate; therefore, many methods of auxiliary ventilation for continuous-mining equipment have been developed and have been discussed in this study.

Jan 1, 1963

By Robert H. Merrill

A method of determining the strength of a mine roof layer in place is described in this report. The method was tested on a limestone roof layer 50 feet wide, 100 feet long, and 20 inches thick. In place measurements were accomplished by introducing air under pressure into a separation between the layer and the overlying roof, and as pressure was increased, the corresponding strain and deflection of the roof layer were measured until the roof failed. The ultimate strength of the roof agreed with the tensile strength of the roof rock (modulus of rupture) as determined in the laboratory; the modulus of elasticity as measured in place did not agree with the laboratory-determined values; the deflection and tensile strain in the layer in place showed good agreement with the theory of a body-loaded beam clamped at both ends. This procedure for determining the strength of a mine-roof layer is safer and less costly than successively widening a roof to failure. For example, it would have been necessary to mine the room to a width of 114 feet and a length of 228 feet to produce failure in this roof layer. The method is not necessarily limited to limestone; any thinly bedded rock type can be tested by this procedure when there is an open parting over the mined area.

Jan 1, 1958

By Jan M. Mutmansky, Christopher J. Rise

"One of the most serious long term health problems associated with underground,mining is Coal Workers Pneumoconiosis (CWI'), more commonly known as Black Lung Disease. It occurs in some coal workers, normally after 15 or more years of exposure to coal mine dust, and leads to a variety of respiratory problems. Two types of pneumoconiosis are recognized simple CWP, which has been estimated to affect 6.9 percent of miners and is a condition that does not impair the miner's ability to work nor reduce life expectancy; and a more severe form of black lung (called progressive massive fibrosis) that occurs in about one percent of the cases and results in severe lung damage.Although the relationship between coal dust and CWP has long been recognized, detailed knowledge of the relationship is insufficient for setting up authoritative guidelines to reduce the health risks for those employed in dusty,underground environments. CWP is not only a health problem for workers that causes considerable distress, it is also a very expensive problem the total annual costs associated with CWP approach two billion dollars.As part of its efforts to combat CWP, the U.S. Bureau of Mines in 1983 established a Generic Mineral Technology Center to carry out basic research into all aspects of respirable coal dust:— control of dust generation — the behavior of dust in the mine — characterization of dust particles interaction of dust and lung— the relationships among dust generation and mobility and the mine environment, geology, and seam characteristics,Penn State, West Virginia University, the University of Minnesota, and the Massachusetts Institute of Technology are involved in this research, which is administered from the Department of Mineral Engineering at Penn State.Our work is one of the seven projects to be conducted at Penn Slate. We are concerned particularly with the characterization of dust and its relationships with the mine environment, and our main goal is to establish standard procedures for describing and measuring these variables.Coal DustCoal dust is a very complex material that varies greatly in chemical and mineralogical properties. Moreover, it is not the only constituent of respirable dust in the mine. When a coal seam is mined, it is inevitable that rock particles other than coal are included in the material. This rock comes from the mine roof, the floor, and the partings and inclusions within the coal scams. Since the roof and floor strata, the partings and inclusions are often stronger than the coal, mining them frequently causes more dust than mining the coal itself. One of the objectives of our research is to find the relationships between a specific coal's characteristics before it is mined and the respirable dust characteristics after it is mined. We are particularly interested in the size distribution of particles, the chemical properties, and the mineralogical properties."

Jun 1, 1988