Search Documents

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

9. Remote Sealing System Sensitivity 9. 1 Introduction In the previous sections a description of the overall system has been presented along with detailed descriptions of the equipment and techniques employed with the preliminary probing system, the seal em¬placement system and the seal checking system. In addition, the use of these subsystems in a specific mine application has been described in considerable detail. A broad range of parameters of interest was specified in the contract, as summarized in Section 1. 3. Most of these are a function of the general location; i. e. , the location of the mine, and the specific location; i. e. , the location of the boreholes. These parameters of interest include passage size, shape, depth, slope and water con¬ditions. The length, diameter and location of the boreholes within the mine passage and on the surface are critical parameters as well. A few additional parameters may affect one or more of the remote sealing subsystems. These include temperature, topography, rock and soil conditions, and underground water. While variation in these parameters will not render the system inoperative, consideration of them in the planning stages will simplify and expedite the field operation. In the following sections the effect of the various parameters on the remote sealing operation will be discussed. For clarity, the several tasks, borehole drilling and casing, preliminary probing, fly ash delivery, foam topping and seal checking, will each be considered separately.

Jan 1, 1973

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By Fred N. Kissell

Tracer gas decay curves were experimentally obtained in a full-scale model coal mine working face area. The concentration of tracer gas was found to decay in exponential fashion but with a change in slope. This change in slope is attributed to eddy zones in the face area. A simple theory was developed that allows one to calculate the approximate amount of gas in the eddy zones and thus estimate the size of the eddy zones.

Jan 1, 1974

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By J. R. Wait, D. A. Hill

A survey of the literature on ELF and VLF atmospheric noise has been made. Most measurements have concentrated on the vertical electric field and the horizontal magnetic field rather than the vertical magnetic field which is of interest in transmission between horizontal loops. The limited vertical magnetic field data indicates that the vertical component is generally 10 to 20 dB below the horizontal component. Three laterally inhomogeneous earth models have been analyzed for conversion of horizontal to vertical magnetic field. The rough surface model examines surface effects, the inhomogeneous thin sheet model treats volume effects, and the buried cylinder model treats localized man-made effects. All three models predict the possibility of significant conversion from horizontal to vertical magnetic field. A thin sheet model has also been used to examine transmission from a buried magnetic dipole source. It is found that the pre- dicted fields more nearly model the measured data than does the homogeneous half-space model.

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX E EQUIPMENT USED FOR FIELD TESTING OF MINE SEALING SYSTEM I. Drilling Operation - Equipment supplied by local drilling contractor 1. Mobile drill rig. 2. Flat bed truck, containing 20 lengths of drill pipe. 3. Auxiliary compressor. 4. Pickup truck for small parts and supply of diesel fuel. 5. Bulldozer. 6. Water supply, in this case the nearby stream. 7. Supply of casing, positioned next to the drill rig. 8. Ready mixed cement grout. 9. Drill bits, stabilizer units, cutting and welding equipment, other miscellaneous tools and supplies. II. Sonar Probing Operation 1. 25 foot tower with pulley mounted atop. - FMA 2. Electric winch with 100 feet of 1/4-inch cable, Model No. 100A, City Engineering Co. , Indianapolis, Indiana. 3. 400 feet of 1-1/2-inch-diameter aluminum pipe with alignment holes and coupling grooves. - FMA*

Jan 1, 1973

By Martin H. Stanczyk

Two methods of recovering zinc from zinc ammonia complex solutions were investigated. One method studied was distillation of the ammonia from the solutions to recover a basic zinc sulfate, which after calcining to zinc oxide was reduced to metallic zinc using hydrogen at 900° C. The second method tested was electrolysis. The tests were made of synthetic and leach solutions analyzing about 80, 100, and 115 gpl (grams per liter) of Zn, NH3, and SO4, respectively. The leach solutions were prepared by oxidation leaching of a sphalerite flotation concentrate, assaying 55 pct zinc at elevated temperature and pressure. The distillation method recovered about 98 pct of the zinc in a product analyzing 97 pct zinc. Ammonia losses incurred during the leaching and distillation operations were about 0.1 lb per lb (pound per pound) of metallic zinc produced. Electrolysis of the solutions at a cathode current density of 25 amp per sq ft (ampere per square foot) yielded zinc deposits assaying in excess of 99.9 pct zinc. About 1.5 kwhr (kilowatt-hour) of power were consumed per pound of zinc deposited; the current efficiency was 72 pct. Other electrodeposition tests revealed that small amounts of ferric iron in the cell liquor were deleterious to electrolysis unless about 5 lb of glue per ton of zinc were present in the electrolyte. The use of glue and vigorous agitation of the electrolyte gave smooth zinc deposits from solutions containing as much as 0.1 gpl iron.

Jan 1, 1962

By Motohisa Kanda

The time and amplitude statistics necessary to adequately describe electromagnetic (EM) noise in mines are illustrated through computer software techniques. They are 1) Allan Variance Analyses (AVA), 2) Interpulse Spacing Distributions (ISD), 3) Pulse Duration Distributions (PDD), 4) Average Crossing Rates (ACR) , and 5) Amplitude Probability Distributions (APD) . These statistics are illustrated using data taken from a rather large store of raw analog data recorded in operational mines. The curves generated for the illustrations characterize the noise environment in the mines from which the corresponding data were taken, and should aid in the design of reliable communication systems for such mines.

By Steven J. Schatzel, Joseph Cervik, Gerald L. Finfinger

Gas drainage through surface bore¬holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwal..ls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole inter¬cepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain¬age during longwall mining will be essen¬tial for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European tech¬niques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

By Terry J. Close

In 1992, as part of the U.S. Bureau of Mines Idaho Land Assessment Program, the Western Field Operations Center investigated the mineral resources of the 30,300-hectare Elk Summit study area. The area is in the Clearwater National Forest, adjoining the Selway-Bitterroot Wilderness in Idaho County. Idaho. The study area is underlain by granitic and metasedimentary rocks. Associated with these rocks are road metal (stone) resources, black sand mineral placer resources, and thermal water resources. Also present are abundant sand and gravel. Two of the five sites examined during the Bureau study have road metal (stone) resources, one has black sand mineral resources, one has thermal water resources. The fifth site is a black sand mineral placer occurrence. There is no evidence of petroleum or coal resources. Idaho County records indicate that 38 mining claims, mostly black-sand placer, have been located in the study area, Twenty-three of the claims are current. Workings consist of a few pits and trenches at the placer, and two borrow pits. The only mineral commodity produced from the area was about 1,500 tonnes of stone excavated from the Savage Pass and Swamp Creek borrow pits along the Elk Summit road, north of Hoodoo Lake. The stone was used to surface the road; these stone resources will continue to be used as needed.

Jan 1, 1993

By Michael A. Trevits

During the time period from 1990-2007, there were 1601 reportable fires that occurred in the U.S. mining industry (an average of 89 fires per year). The leading causes of U.S. mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion. The National Institute for Occupational Safety and Health (NIOSH) is conducting a program of research addressing metal/nonmetal and coal mine fire prevention, detection, management and suppression. In the metal/nonmetal area, work was focused on technology transfer and training, and research to reduce the number of mobile equipment fires and their hazards. In the coal arena, research is underway to determine the root cause of cutting and welding-related fires and to evaluate the effects of ventilation schemes relative to the spontaneous combustion risk in longwall mines. Relative to fire management, research is ongoing on remote mine seal installation and remote mine fire suppression technologies. Finally, research is continuing to develop comprehensive and usable smoke management techniques and to develop mine fire growth models, propagation, and suppression. This paper presents a summary of some of the mine fire research and provides an overview of the next phase of the NIOSH mine fire research program.

Jan 1, 2010

This section contains a summary of our investigation of the soil conditions (type, porosity, moisture content, etc.) at the two sites (Lanse and Kato, Pennsylvania) selected for field testing of latex as a soil sealant. Other natural conditions such as rainfall, frostline, depth of the water table, etc., were also measured and recorded for possible later use in assessing the effect of the latex seal on the total environment. The numbered sites referred to throughout this report are shown on the maps of the Lanse and Kato sites (Figures 1 and 2). KA, RB and KC are positions at the Kato site - all other numbered positions refer to the Lanse site. Two other terms used throughout the report which should be explained are “horizon” and "profile". These are synonymous terms for soil layer, A horizon (or A profile) referring to topsoil and B horizon (or B profile) referring to subsoil. The properties that control the flow of water through the soil are of special interest because these will also govern the passage of a sealant into and through the soil. Normally the particle size distribution is a good measure of soil permeability, which is directly proportional to sand content and inversely proportional to silt and/or clay content. Tables I1 and I11 show the percentages of gravel or stones, sand, silt and clay of Lanse and Kato soil samples. According to the United States Department of Agriculture classification, the gravel is ,ignored and the residue separated into sand, silt, and clay fractions. Figures 4 and 5 indicate by means of the USDk soil texture triangle that the variability of composition of Lanse soil ranges from sandy loam in the creekbed to clay loam. The variation is even greater among soil samples from Kato. Porosity of soil, also known as percent voids, is another indication of how readily water will travel through soils. Soil density usually increases and porosity decreases with depth, and as expected, the porosity of the top soil at Kato, a forest, is exceptionally porous and open (see Table IV) The pore diameter and length of soil capillaries is extremely variable, and its distribution in the field is impossible to determine. In addition to the capillaries, soil also contains many macro cracks, crevices, and passages around stones and roots. All these affect the flow rate of water through soil. Poiseuille's law states that the rate of flow of a liquid through a narrow tube is proportional to the 4th power of the radius of the tube. Pore size normally decreases with depth and in soil containing appreciable amounts of silt and clay this is especially true. Thus, deeper soils should be less permeable and such was the case at Lanse and Kato.

Jan 1, 1972

By Charles Zahn

Gas chromatography is a method of separating mixtures of gases and volatile materials by entraining their vapors in a gas stream, which passes over an appropriate stationary phase. Two techniques are in common use: Gas-Liquid Chromatography, in which the stationary phase is a liquid supported on an inert solid, and Gas-Solid Chromatography, where the stationary phase is a solid adsorbent, such as charcoal or alumina. In both techniques components emerge from the column after a characteristic residence time. Gas chromatography is applicable as a qualitative or quantitative tool in a wide variety of problems in chemical research and processing. It may also be employed for purification and separation. A running bibliography on gas chromatography has been maintained at the Bureau of Mines synthetic liquid fuels laboratories, Bruceton, Pa., for several years for the benefit of research workers, who use chromatography as an analytical tool. Since the number of references grew and interest in the technique became more wide-spread, the Bureau is publishing this list rather than maintain it as a purely internal source.

Jan 1, 1958

By John C. Franklin

The Bureau of Mines conducted extensive laboratory and limited field tests to determine whether a polymeric material could effectively reduce the emanation rate of radon gas from uranium ore. In the laboratory 46 different single-coat materials and 14 two-coat applications were tested. The laboratory tests showed that up to 100 percent of the radon gas could be sealed into the rock. Materials tested in the laboratory were polyesters, furan resins, epoxies, latices, and totally inorganic coatings. From the laboratory work six different materials were selected for field testing. The first test was single-coat materials in five static chambers; the second test used two-coat applications in an open chamber. Both tests were conducted in the Dakota mine at Grants, N. Mex. During the second test, the amanation rate of radon gas was reduced up to 62 percent.

Jan 1, 1975

By C. B. Manula, R. L. Sanford, R. A. Rivell

Development of the Rail-Haulage Sub-assembly for the Production Sub-system (UGMHS)* required the use of ,a newly formulated model in order to best satisfy the requirements. Many of the ideas of the former single-stage rail simulator included in the original version of UGMHS have been used, together with the results of experience gained in applying the earlier model to a variety of operating situations (Sanford, 1969). The sub-assembly is developed as an independent system and, as such, can be used to analyze track systems using production distri¬butions as data input. In addition, since this model is designed to replace the original sub-assembly in UGMHS, the linking procedure is identical with respect to bi-directional information flow. The flow of coal from production sections, for example, fills the mine cars, but a condition of "out of empties" or "full of loaded" at a loading station will shut down inby production sections. A requirements analysis was conducted to determine specifically how the model could best serve the user. Operating management had the largest input in developing the following requirements for the Rail Sub-assembly: a) data input in mixed narrative - numeric form to permit user identification of the input variables; b) a user option to extract several ranges of detail in model output, i.e., an average shift summary of minimum retrieval

Jan 1, 1974

Control dust generated during undercutting in salt mines without causing ore-solubility problems that result from excessive water use. Approach A foam generator was developed to provide a reliable foam to control dust on cutting machines used in mining water-soluble ores. The system was designed to keep total foaming agent/water mixture flowrates below the flow-rates characteristic of water-only systems. The foam generator consists of a reservoir to hold the premixed agent and water, a metering pump, and a small compressor to aerate the mixture. The system is compatible with all cutting machines. How It Works One of the current wet-bar techniques, the through-the-bar trickle system, pumps water through a pipe in the cut-ting bar to its tip placing the water behind the kerf. If the pipe conducted foam effectively the foam would be released in the kerf where it would mix with the cuttings and the dust produced by the chain. For improved foam delivery, however, it is recommended that the pipe be replaced with an external channel welded along the top of the bar. This provides excellent dust control while avoiding the accumulation of copious quantities of foam in the heading. The system is very simple. The foam generator is a 50-gallon tank filled with a mixture of water and foaming agent. The mixture is pumped through a wye fitting to a second line where it is mixed with compressed air, (300

Jan 1, 1984

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983

Develop a simple and practical technique to measure in situ rock mass properties for realistic design and stability evaluation of underground structures. Background The Bureau of Mines has developed basic principles and techniques to determine in situ rock mass properties including Poisson's ratio, deformation modulus, and yield and failure strengths. An instrumentation package consisting of three pressure cells is installed in a single drill hole. Cell pressure response data are acquired and used to calculate and determine the rock mass properties. How It Works A test hole of BX size (approximately 5.7 cm) or larger is drilled to the approximate depth of the measuring point. The last portion of the test hole is drilled with precision bits to EX size (approximately 3.8 cm). The instrumentation package, which consists of one 3.8-cm-diameter cylindrical pressure cell (CPC) and two 5.7-cm-diameter cement-capsulated, flat borehole pressure cells (BPC's), is then installed. A complete history of cell response to changing strata loads is acquired on a continuous basis with a chart-type hydraulic pressure recorder. From these cell pressure data, Poisson's ratios, deformation moduli, and yield and failure strengths are calculated and determined.

Jan 1, 1990

By W. D. Bensema, J. W. Adams, W. W. Scott, H. Dobroski

Measurements of the absolute value of electromagnetic noise and attenuation along a hoist rope were made in an operating hard-rock mine, Lucky Friday Mine, located near Wallace, Idaho. Spectra of electromagnetic noise generated by various pieces of equipment, spectra of specific noise signals at various depths, and noise and attenuation on the 4250 foot (1295 meter) hoist, were measured. Three techniques were used to make the measurements. First, noise was measured over the en- tire electromagnetic spectrum of interest for brief time periods. Data were recorded using broadband analog magnetic tape for later transformation to spectral plots. Second, noise amplitudes were recorded at several discrete frequencies for a sufficient amount of time to provide data for amplitude probability distributions. A third technique gave attenuation data through the direct measurement of field strength at various depths. The specific measured results are given in a number of spectral plots, amplitude probability distribution plots and amplitude curves as a function of depth.

Jan 10, 1974

By Charles L. Kimbell

Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area (table 14) was not available in time for inclusion here, thus this information remains the same as was presented in the previous edition of this chapter. The salient statistics on U.S. foreign investment in mineral industry activities (table 15) as reported by the U.S. Department of Commerce has been revised to show the latest information for the years 1986-90.

Jan 1, 1993