Search Documents

By James J. Olson

The Bureau of Mines recorded and analyzed overpressure levels for three production blasts at the White Pine copper mine, Upper Michigan, to obtain representative data from single-heading blasts in a long, straight haulageway and to estimate the damage potential inherent in production blasts fired in close proximity to underground structures. Commercial pressure gages with a flat response to 1 kHz were used with an FM tape recorder to record the overpressures from one dynamite and two AN-FO (ammonium nitrate-fuel oil), 500-msec production blasts having zero-delay charge weights of about 75 lb (34 kg). The recorded waveforms from the underground blasts (1) were more complex than the typical free-air wave, (2) were of longer duration, and (3) had numerous secondary arrivals due to reflections from the ribs and roof. The waveforms showed that the zero-delay charges produced the only high overpressures. First pulse peak overpressures from the blasts ranged from 0.10 lb/in2 (6.9 X 102 N/m2) at a distance of 471.1 ft (144 m) to a maximum of 1.76 lb/in2 (121.3 X 102 N/m2) at 191,7 ft (58.4m) from the blasts. An analysis of variance of the first pulse overpressures from the three White Pine blasts showed that no statistically significant difference existed among the overpressure levels from the dynamite and AN-FO blasts and that a single equation P = 4.9 x 103 (D /W1 / 3) 2 .15, where P = overpressure in pounds/inch2, D = d-stance from the blast in feet, and W = zero-delay charge weight in pounds, could be used to describe the falloff of overpressure with distance.

Jan 1, 1971

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By Martin S. Oudenhoven

This report describes the results of a Bureau of Mines investigation in which the stress concentrations and distributions caused by inclusions in a strained elastic plate were determined, Finite element analyses were made for 168 models containing single inclusions of elliptical, ovaloidal, and rectangular shape. The variables studied included: horizontal-to-vertical loading ratios, (Sh/Sv) of 0,0.33,0.5, and 1.0; width-to-height ratios (w/h), of 0.25, 0.5, 2, and 4; and Young's modulus of inclusion to Young?s modulus of plate ratios (K ratios) of 0.33, 0.5, 2.0, and 5.0. The results show that the theory for elliptical inclusions can accurately predict the average stress along the x and y axes of symmetry for circular, ovaloidal, and rectangular inclusions from the width-to-height and K ratios. The actual inclusion shape was insignificant, suggesting that the average stresses in other inclusions of irregular shape (orebodies) can be estimated with the theory for an elliptical inclusion. An application of this technique to mining problems is presented. The stresses in the elliptical inclusions were uniform throughout the inclusion for all the models studied.

Jan 1, 1972

By Edward F. Divers

This Bureau of Mines report describes the results of a program to develop small, rugged scrubbers with high dust collection efficiency for use in under-ground coal mines. The Bureau's Pittsburgh (Pa.) Research Center has developed and assisted in the development of several types of improved scrubbers that are especially suitable for various underground mining applications. Research efforts concentrated on reducing the size, power, and water consumption of these scrubbers, while optimizing their dust collection efficiency. Fractional dust collection efficiency, air volumetric range, size, power, water consumption, and application guidelines for each type are described. Air pressure differentials ranged between 2-and 3D-inches water column (wc). The dust collection efficiency of six scrubbers--a venturi, two flooded-fibrous-bed, a venturi-impaction plate, a wetted-fan, and a rotating flooded-bed--were compared. The rotating flooded-fibrous-bed and the stationary flooded-fibrous-bed scrubbers showed the highest coal dust collection efficiency. Test results show that these scrubbers can generally achieve respirable size coal dust collection efficiencies in the high 90-pct range required to reduce both long-(8-hour) and short-term coal mine dust concentrations below Federal requirements.

Jan 1, 1979

By D. Harrington, R. R. Sayers

For several years the writers have been studying various phases of the effect of air conditions in metal mines upon underground workers ; in 1918 a short study was made in certain hot and deep mines and brief reports were issued in the Engineering and Mining Journal ( August , 1920) and in the U. S. Public Health Reports (Vol . 36 , No. 4 , January 28 , 1921 ) . In 1921 a more extended study was made (also in hot and deep metel mines ) with intent to determine the limiting conditions imposed upon underground workers by the physiological effect of various air movements , temperatures , and humidities , with and without work . It is the purpose to publish a series of short papers on this later investigation , each paper to consider one particular phase of the work . The present paper deals with the effect on body temperature and pulse rate in still air as compared with moving air of temperatures from 90 to 100° F . and 100 per cent relative humidity, the subjects at rest .

Apr 1, 1923

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

By Donald P. Mickelsen

The raining and quarrying trends data shown in this report were reported to the U.S. Bureau of Mines (USBM) by mining and quarrying companies on the Mine Information Supplement survey, as well as by mineral producers on 58 annual USBM production and consumption surveys covering 59 nonfuel mineral commodities. The 1993 data presented in the tables of this chapter, were processed for the first time using the USBM Automated Mineral Information System. Domestic mining of nonfuel mineral materials totaled 3.7 billion metric tons in 1993, including 2.2 billion tons of crude ore nun& or quarried and 1.5 billion tons of mine waste and ore from development. This \vas an overall increase of 11% over that of 1992. These data do not include construction sand and gravel which until 1993 has been surveyed biennially. Starting in 1994, construction sand and gravel and the stones, which were also surveyed biennially, will be surveyed annually.

Jan 1, 1993

By Sidney Katell

Continuing the series of cost bibliographies which was initiated with the publication of Information Circular 7516 in October 1949, the present report covers the period from January 1959 through December 1959. The abstracted articles, concerned with all facets of cost engineering in the field of petroleum and chemical plants and related facilities, were obtained from the following sources: 1. Bureau of Mines Information Circulars. 2. Bureau of Mines Report of Investigations. 3. Chemical Engineering. 4. Chemical Engineering Progress. 5. Chemical Week. 6. Coal Age. 7. Coal Utilization. 8. Cost Engineering. 9. Industrial and Engineering Chemistry. 10. Nucleonics. 11. Oil and Gas Journal. 12. Petroleum Engineering. 13. Petroleum Refiner. 14. World Oil. On Oct. 16, 1959 a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers became effective. This agreement provides for the publication of the annual bibliography under the sponsorship of both groups with the work load involved in the preparation divided equally between the two. As a result, the present report partially reflects the efforts of the members of the Association.

Jan 1, 1960

By D. G. Lee

Diesel particulate matter (DPM) often contains small amounts of metal as a minor component but this metal may contribute to adverse health effects. Knowledge of the mechanism for particle formation as well as the size preference of the trace metals is critical to understanding the potential for health concerns. To achieve this, the size and the composition of each particle should be optimally measured at the same time. Single particle mass spectrometer (SPMS) would be the best tool for this objective. In this paper, we therefore will introduce new findings about the mechanism and distribution of the trace metals in DPM, derived from a study where an SPMS was used to analyze freshly emitted DPM. KEY WORDS : Single particle mass spectroscopy, Diesel particulate matter, Characterization, Metal contents

Jan 1, 2006

By J. E. Tiffany

"The new permissible blasting device, Cardox, utilizes as a blasting agent liquid carbon dioxide which is discharged.as a gas from a steel container or shell. The loaded shell is placed in a borehole, stemmed, and tamped in a manner similar to that employed with explosives, and is fired by electricity.The Bureau of Mines' approval for use of the device in coal mines was granted as Approval No. 1 under date of October 3, 1928; as the result of tests made under the conditions and requirements of Schedule 20. There have been three subsequent extensions whereby minor modifications in the original design were granted.The permissibility of the device is subject to the following conditions; (1) It shall be in all respects similar to the sample submitted for tests; (2) certain thicknesses of disc and. weights of heater ingredient and of carbon dioxide, all of which are set forth in Table 2 under the provisions governing permissibility, must be used: (3) the rear cap must always be in place after the shell has been charged, to prevent accidental firing; and (4) firing must be done by means of a permissible-type blasting unit.The permissibility of Cardox was established by gallery tests similar to those used in testing explosives for permissibility. In these tests the shell was discharged into gallery 1 without causing any ignition of gas and air or of gas, dust, and air mixtures there. The conditions of charging the shell, such as weight of the ingredients of the heater element, the carbon dioxide charge, and thicknesses of the disc, were varied according to the conditions under which it would be likely to be used in blasting. The tests made in gallery 1 are here described in detail, as are also the tests which have been made for determining the propulsive strength of the device and the quantities of poisonous gases given off when a shell is discharged."

Mar 1, 1929

By Stephen C. Brown

THE expansion of the world economy which has been in process since 1958 continued in 1963 and both production and consumption of minerals rose. Gross national product (GNP) rose sharply in the United Kingdom and Japan, continued to expand in the United States and Canada, and maintained a high though slightly declining rate of growth in the European Economic Community (EEC) despite the appearance of excess capacity in certain lines and inflationary pressures in Italy and France. The steel and motor vehicle industries both increased output in North America, Western Europe, and Japan. The less developed areas benefited substantially from an improvement in their terms of trade, and their export earnings increased some 8 percent in 1963; although estimates of GNP for the majority of them are 110t yet available, it is probable that this increase was partly reflected in a substantial rise of GNP.2 In the United States the expansion was steady and extended through all sectors of the economy producing no distortions likely to disturb its continuing growth; at yearend with unemployment still at about 5.5 percent of the labor force and operating rates of industry estimated at about 87 percent of capacity, there was a substantial margin for further expansion. Though the balance of payments was still in heavy deficit for the year, in the last half it was moving rapidly toward equalibrium as net exports rose and capital outflows declined; prices were relatively stable, inventories increased only slightly and the activity of mineral-consuming industries remained high, steel output rising by 11 percent to highest level since 1957 and the auto industry output equalling the 1955 record.3

Jan 1, 1964

By Manuel Gomez

A general prediction model for the Hardgrove grindability index was constructed from 735 coal samples using the proximate analysis, heating value, and sulfur content. The coals used to develop the general model ranged in volatile matter from 12.8 to 49.2 percent, dry basis, and had grindability indexes ranging from 35 to 121. A restricted model applicable to bituminous coals having grindabilities in the 40 to 110 range was developed from the proximate analysis and the petrographic composition of the coal. The prediction of coal grindability within a single seam was also investigated. The results reported support the belief that mechanical properties of the coal are related to both chemical and petrographic factors of the coal. The mechanical properties of coal may be forecast in advance of mining because the variables used as input to the prediction models can be measured from drill core samples collected during exploration.

Jan 1, 1970

By W. E. Wallace, B. L. Razzaboni, P. Bolsaitis, M. J. Keane

"Therma1 and chemical treatment of respirable size silica dusts samples is shown to induce marked changes in their hemolytic activity. The cytotoxicity of crystalline a-quartz (Min-U-Sil), and fumed silica (Cab-0- Sil) particles, as measured by a hemolytic activity protocol, is decreased by calcination and can be related to the dehydroxylation of the surface. The hemolytic activity of P-cristobalite particles of respirable dust si7.e was also determined and found to be lower than that of a-quartz. The change in the surface structure resulting from thermal treatment is detectable by photo-acoustic infrared spectroscopy and zeta-potential measurements. The absorption band in the 3200-4000 cm-1 frequency region of both Cab-0-Sil and MinU- Sil disappears upon heat treatment while a sharp band, identified with single silanol groups, at 3750 cm-1 increases in intensity. The zeta potential-pH profile, in the pH range of 4.0-7 .0, of the calcined, siloxane surfaced particles is more negative than that of material with a silanol surface.The cytotoxicity of the crystalline and fumed silica dusts was also found to be strongly dependent on particle size. Fumed silica of large surface area (small particle size) exhibits an initial increase in hemolytic activity upon calcination. This result confirms other experimental observations pointing to a particle size of maximum toxicity. INTRODOCTIONThe toxicity of silica and other mineral particles, as manifested by their role in inducing pneumoconiosis, fibrosis, silicosis and other pulmonary disorders is largely traceable to the characteristics of particle surfaces and to particle morphology. The great wealth of data on the physical and chemical properties of silica is still insufficient for a comprehensive understanding of the specific parameters to be associated with fibrogenic activity and, correspondingly, with the optimum means for characterizing and quantifying the toxicity of dusts, and the design of possible preventive or therapeutic methods.The great diversity of parameters that have been proposed and tested for correlation with cytotoxicity suggest that more than one mechanism may be involved in the fibrotic activity of silica particles. The crystalline structure of the material (more active tridymite versus less active crisobalite and passive stishovite), freshly formed surfaces and free radicals associated therewith, silicic acid adsorbed onto silica surfaces, the concentration of hydroxyl groups at silica surfaces, particle size and morphology, among other properties, have been investigated and found to conelate in tests of cytotoxicity."

Jan 1, 1990

By J. B. Janus

This Bureau of Mines publication updates a series of reports on the quality of coal purchased under specifications for Government use. Listed are analytical data on the composition and quality of tipple and delivered samples of coal collected during the period July 1975 through September 1976.

Jan 1, 1977

By E. C. Lane

This report on properties of commercial motor fuels is the twelfth in a series made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the Interior. The first report contained data on motor gasolines sold during the winter of 1935-36.V The -present report, covering the summer of 1941, presents analytical data for 1,857 samples, representing the products of approximately 135 companies. As in previous surveys, these companies include both large and small suppliers. In addition, the Pacific coast is represented by data averaged by the Pacific Coast Technical Group before being submitted, and these data are published exactly as they were received. Conforming to previous surveys, the data cover three groups of samples -- regular-price, premium-price, and third-grade gasolines -- and each group has been aver aged separately. The number of samples, items, and brands comprising each group, exclusive of those of the Pacific coast, are as follows: Regular price, 1,010 samples, 291 items, and 86 brands; premium price, 577 samples, 263 items, and 78 brands; third-grade gasoline, 270 samples 159 items, and 74 brands. The meanings of these terms as used in the surveys are as follows: Sample: The individual supply of gasoline obtained at the filling station and analyzed in the laboratory.

Jan 1, 1942

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

6. Development of Mine Sealant Material Systems 6. 1 Introduction The preliminary evaluation of material systems described in Section 3 led to the selection of the following four promising systems for further development: System A: Aggregate, Fly Ash System System B: Aggregate, Fly Ash, Urethane Foam System System C: Aggregate, Bulkhead, Light Expansive Concrete System D: Aggregate, Self-Supporting Thick Slurry Preliminary laboratory tests indicated that the building of effective bulkheads from one borehole would be extremely difficult. Two extra boreholes would be required adding to the overall cost of the system and making the system less attractive. Tests with light expansive concrete showed that bulkheads would be required, the material would not support itself. As a result, further development of this system was terminated. Foam concrete was selected as the most suitable material to be developed into a self-supporting, rapid-setting slurry. A laboratory investigation of its use for mine sealing was conducted during this program; the results are summarized in Section 6. 5 and details of the laboratory program are presented in Appendix B.

Jan 1, 1973

By Hugo E. Camargo

In an effort to reduce Noise Induced Hearing Loss (NIHL) in the mining industry, the National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop noise controls for mining equipment whose operators exceed the Permissible Exposure Level (PEL). The process involves three steps: 1) Noise source identification (NSI), 2) development of noise controls, and 3) evaluation of the developed noise controls. For the first and third steps, microphone phased array measurements are typically conducted and data are processed using the conventional beamforming (CB) algorithm. However, due to the size and complexity of the machines, this task is not straight forward. Furthermore, because of the low frequency range of interest, i.e., 200 Hz to 1000 Hz, results obtained using CB may show poor resolution issues which result in inaccuracy in the noise source location. To overcome this resolution issue, two alternative approaches are explored in this paper, namely the CLEAN-SC algorithm and a variarion of an adaptive beamforming algorithm known as Robust Capon Beamformer (RCB). These algorithms were used along with the CB algorithm to process data collected from a horizontal Vibrating Screen (VS) machine used in coal preparation plants. Results with the array in the overhead position showed that despite the use of a large array, i.e., 3.5-meter diameter, the acoustic maps obtained using CB showed "hot spots" that covered various components, i.e., the screen deck, the side walls, the I-beam, the eccentric mechanisms, and the electric motor. Thus, it was not possible to identify which component was the dominant contributor to the sound radiated by the machine. The acoustic maps obtained using the RCB algorithm showed smaller "hot" spots that in general covered only one or two components. Nevertheless, the most dramatic reduction in "hot" spot size was obtained using the CLEAN-SC algorithm. This algorithm yielded acoustic maps with small and well localized "hot" spots that pinpointed dominant noise sources. However, because the CLEAN-SC algorithm yields small and localized "hot" spots, extra care needs to be used when aligning the acoustic maps with the actual pictures of the machine. In conclusion, use of the RCB and the CLEAN-SC algorithms in the low frequency range of interest helped pinpoint dominant noise sources which otherwise would be very hard to identify.

Jan 1, 2009

By J. F. Barkley

The following questions and answers were prepared principally to supply information in answer to general inquiries received by the Bureau from those contemplating the use of propane and butane fuels . Primary or basic information only is covered; this usually gives enough guidance for most inquirers . To those who wish information of the treatise type , the handbook , Butane- Propane Gases , published by the Jenkins Publications , Inc. , 1709 West 8th Street , Los Angeles 14, Calif . , is suggested .

May 1, 1949

By D. R. Tesarik, M. K. Larson, D. K. Denton, J. B. Seymour, R. L. Rains, T. J. Williams

Because backfill has occasionally collapsed into an active working area, posing a hazard to miners, engineers from the Spokane Research Laboratory of the National Institute for Occupational Safety and Health and Hecla Mining Co. installed instruments in a cemented, backfilled, stope-ramp intersection at Hecla’s Lucky Friday Mine, Mullan, ID. The purpose was to measure stress and strain changes in the backfill and reinforcing members during undercut mining. The instruments were monitored for 6 months while three successive cuts were mined below the intersection. Readings showed induced loads up to 3450 kPa (500 psi) in the backfill as stope walls converged 2.5 to 12 cm (1 to 5 in). The backfill then deformed against the top and bottom plates of the 2-m- (6-ft-) long vertical rock bolts installed as reinforcement, producing loads to 177 kN (40,000 lb)on the rock bolts. We hypothesize that a compressive zone was created in the backfill that allowed the backfill to remain stable as long as the compressive zones from adjacent rock bolts overlapped. This hypothesis is presented in graphical form. Of particular interest was the effect of loading on trusses installed to augment the vertical rock bolts and wire mesh typically installed in backfill. Data from the instruments indicate that wall closure perpendicular to the vein induced loads in truss legs parallel to the vein and in the rock bolt driven through the center of the truss, but, because they are designed to function under tension, truss legs perpendicular to the vein supplied in significant support as a result of compressional forces from wall closure. Based on this study, use of trusses was discontinued, and an alternative support system of wood beams and posts was installed as needed to ensure the safety of miners working beneath the backfill in stope-ramp intersections.

Jan 7, 2001

By B. Dimitriades

Data on smog-forming reactivities of exhaust aldehydes are scarce. Such data were obtained by irradiating in a smog chamber typical exhaust aldehydes, individually and in exhaustlike mixtures. Observed reactivity manifestations were rate of nitrogen dioxide formation (RNO2) and yields of oxidant, peroxyacetyl nitrate, and formaldehyde. Results showed that exhaust aldehydes vary widely in reactivity. Formaldehyde showed high RNO2 reactivity but low oxidant yield; benzaldehyde, [m]-, and [p]-tolualdehyde were totally unreactive when irradiated individually; [o]-tolualdehyde was reactive. In mixtures, benzaldehyde manifested reactivity in terms of peroxybenzoyl nitrate yield. Exhaust aldehydes as a group are judged to be as reactive as the exhaust olefin group. The importance of the aldehyde contribution to exhaust reactivity and methods for assessing such contribution are discussed.

Jan 1, 1971