Search Documents

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By R. G. Sandberg

Many gold-bearing ores throughout the Western United States contain small quantities of mercury. The presence of mercury not only decreases the gold-loading capacity of the activated carbon, but complicates the fire refining of cathodes and creates a potential health hazard. The Bureau of Mines investigated methods to limit mercury extraction during gold ore leaching and to remove mercury from cyanide leach solu-tions. Mercury dissolution was reduced from 40 to 10 pct by decreasing NaCN concentration from 20 lb to 0.34 lb per ton of solution at a pH of <11. When 0.1 lb CaS per ton of ore was added to a leach slurry, mer-cury extraction was reduced from 27 to 0.4 pct. Less than 0.5 pct of the mercury was solubilized when <0.1 lb CaS per ton of are, along with lime and NaCN, was added to a simulated grinding circuit.

Jan 1, 1984

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

Pillar design is the first line of defense against rock falls—the greatest single safety hazard faced by underground coal miners in the United States and abroad. To help advance the state of the art in this fundamental mining science, the National Institute for Occupational Safety and Health organized the Second International Workshop on Coal Pillar Mechanics and Design. The workshop was held in Vail, CO, on June 6,1999, in association with the 37th U.S. Rock Mechanics Symposium. The proceedings include 15 papers from leading ground control specialists in the United States, Canada, Australia, the United Kingdom, and the Republic of South Africa. The papers address the entire range of issues associated with coal pillars and have a decidedly practical flavor. Topics include numerical modeling, empirical design formulas based on case histories, field measurements, and post failure mechanics.

Jan 5, 1999

By D. Harrington

The mining industry of the United States has for many years possessed the dubious aistinction of having the poorest accident rate of all of the major lines of industrial endeavor in this country, and until recently there ras little or nothing to show that any material improvement might be expected. However, there are now numerous trends indicating that the corner has ceen turned at last, and it is strongly hoped that the mining industry is likely to follow the railroads, the cement and other industries in operating with occurrence of only a reasonable amount of loss of life and limb through accidents. The complete accident figures for metal and nonmetallic mineral mining for 1931 are not yet available, but fragmentary data shor that 1831 vill un- questionably have very low accident rates, probably the lowest in the history of our metal mines. One underground metal mine has produced over 14,000,000 tons of copper ore rithout a fatality; another metal mining company with an electric slovel operation has handled upwards of 75,000,000 tons of material, copper ore and waste, without the occurrence of a fatality; an iron-ore compan, which orns six mines (three underground, three open pit), has operated every one for a year or more without a lost-time accident with a con- siderable number of employees and a large production; and alot.er iron-ore producer with 30 mines and about 3,000 employees as an average of nearly 10 months of operation in 1931 without a lost-time accident. umerous other wonderful safety records of metal mines in 1931 indicate unmistaimbly tat the record of the noncoal mining industry of the United States as a role in 1931 will undoubtedly be found to be excellent. According to the latest relatively complete figures (those of 1930) available for the coal industry, fewer than 650,000 persons are employed in and around the coal mines of the United States, the figures indicating at a little over 493,000 people are engaged in bituminous mining and a little under 151,CCO in anthracite mining. Bureau of Mines complete figures suc that 2,053 persons were killed and 103,821 non-fatally injured in our coal

Dec 1, 1932

By John Ward Smith

The Bureau of Mines drilled Wyoming Corehole No. 1 in Sweetwater County, Wyo., to sample Green River Formation oil shale. Core obtained was assayed for oil yield to determine richness and stratigraphic distribution of oil shale in the deposit. Oil shale in place at Wyoming No. 1 site represents over 200 million barrels of oil per square mile. Additional data useful in evaluating the deposit, including generalized stratigraphy and mineralogy, detailed lithologic descriptions of the core, rock specific gravity, and bore-hole logs, are presented with the oil-yield data. The sampled Wyoming oil shale resembles Mahogany-zone oil shale in rock properties and gross mineralogy. A statistically derived equation relating shale density to oil yield for the Wyoming deposit compares with a similar relationship valid for the better known Mahogany-zone oil shales in Colorado and Utah. A density log from Wyoming Corehole No. 1 is calibrated for direct oil-yield logging. The alternating rich and lean beds of shale at this site may permit creating the permeability necessary for direct production of shale oil from the shale in place.

Jan 1, 1968

By Thomas S. Jones

This Bureau of Mines publication reviews characteristics, manufacture, and uses of natural and synthetic iron oxide pigments. Supply and demand trends within the domestic industry and in foreign trade are presented for 1955 through 1976. Iron oxides are expected to continue in demand for traditional uses, and if anything, to be favorably affected by technological developments. Imports have been significant in relation to domestic production, most notably for synthetic oxides from West Germany and Canada.

Jan 1, 1978

By George S. Rice

"It is well known that the lost coal left in the ground in mining, under such conditions that recovery is practically impossible, constitutes a large proportion of the coal in the beds worked. A recent estimate, in a paper on ""The World's Fuel Supply"" presented by Prof. L. P. Breckinridge, of Yale University, before the Annual Meeting of the. American Society of Mechanical Engineers, places the average loss in bituminous coal mining as one-third left in the ground.The bald statement that there is a loss of one ton of coal for every two recovered may seem to those not familiar with coal mining to imply inexcusable and wanton waste. Perhaps a better way of expression is in terms of total recovery rather than in terms of losses. Many mine superintendents and mine owners will readily concede that their total recovery may be only 60 to 75 per cent, but to state that they are wasting 25 to 40 per cent arouses antagonism. The suggestion is of willful waste, whereas the majority of the operators try to the best of their ability to get a high recovery under the adverse and complex conditions that confront them. These involve natural, commercial, and labor conditions, and the requirement in many cases of boundary pillars under railroads and buildings, which may be called for in the deed or lease, or in the absence of specific exemption in the deed or lease, the common law requirement that a surface owner is entitled to the support of the surface."

Apr 1, 1921

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By W. W. Weller

Heat capacity measurements of anhydrous cobalt sulfate (CoSO4), copper sulfate (CuSO4), nickel sulfate (NiSO4), and zinc sulfate (ZnSO4) were conducted over the temperature range 51° to 298° K. The results were used to evaluate the following entropies at 298.15° K (cal/deg mole): CoSO4, 28.1; CuSO4, 26.8; NiSO4, 24.8; and ZnSO4, 26.4. Entropies were combined with heats of formation to give free energies of formation.

Jan 1, 1965

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United States. The first report7 on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline.8 The present paper reports results of the examination of the gasolines for color, doctor test, gravity, end point, per cent recovered, copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

7133. Clewell, D. H. The Gravimeter. Prec. and Trans. Texas Acad. Science 1941, Austin, Tex., vol. 25, 1942, pp. 86-88. Static gravimeters, unastatized and. astatized, are considered to be the most practical for oil exploration. One gravimeter is described using a beam whose moment about a pivotal axis is elastically balanced. Magnetic or electric fields are deemed unsatisfactory for balancing gravitational force because they cannot easily be kept constant. The gravimeter described is capable of detecting a change in altitude of 3 inches and a change in latitude of about 150 feet. V. S.

Jan 1, 1944

By John Neil, John Bli ard

Coke breeze consists of the smaller particles of coke formed by handling coke on and after removal from the ovens. Its value as F, fuel is less than that of the larger pieces, both because the smaller pieces contain more ash and therefore have a lower calorific value, and because a greater draft is required to burn it.The tests described below show its value as a fuel when mixed with bituminous coal and burned in a hand fired boiler of a size considerably greater than that used in an ordinary house. The results of these tests, however, can be used to give a fairly good indication of the value of coke breeze when burned with bituminous coal in a domestic furnace.All who fire a domestic furnace know that for only a comparatively short part of the day, and then only on a few days, is it necessary to open fully the ash, pit door and stack damper to get the required rate of combustion in the average furnace in the average house. It will be practical, therefore, during the greater part of the heating season, to fire coke breeze with the coal and use more of the available draftsFor domestic heating the coke breeze should be stored separately, and used when the draft is sufficient to burn it in mixture with bituminous coal, at the rate required to warm the house.Purpose of tests: The tests were carried out at the request of the Chamber of Commerce of Pittsburgh, Pa., in order to determine the steaming value of coke breeze as a fuel when mired with Pittsburgh coal and fired by hand, and to see whether the mixture when burnt would give off an objectionable quantity of make.

May 1, 1921

The Bureau of Mines has sponsored a comprehensive research program to enhance the safe, effective, and efficient use of blasting technology by the mining industry. Recent research results of the surface mine blasting program were presented at a seminar on April 25, 1987, in Chicago, IL. Many of the topics discussed at the seminar are presented in this proceedings. The new research described in these papers includes computer monitoring of rock motion, the influence of blast delay times on rock fragmentation, blasting effects on Appalachian water wells, blast vibration measurement near structures, and the reduction of accidents through improved blasting safety.

Jan 1, 1987

By Binyon E. O.

The tungsten properties of Lincoln Mines, Inc., and North Tem Piute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co. Claims leased by the Lincoln Mites, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57&apos; E.; and sec. 1, T. 4 S., 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc., and general offices are in the Wesley Temple Building, Minneapolis, Minn.

Jan 1, 1950

By Guy A. Johnson

To improve productivity and cut costs, modern underground mining operations have become more mechanized. This mechanization has increased the usage of fuels, hydraulics, and electrical equipment associated with diesel-powered vehicles, thereby also increasing the hazards of underground mine fires. The Bureau of Mines evaluated the fire hazard problem and assembled prototype components for a system that would automatically sense and extinguish fires on mobile underground equipment. The prototype system and alternative designs were in-mine-tested and proved effective. This report summarizes this technology, which can cost effectively help solve the problem of fire hazards on underground vehicles.

Jan 1, 1983

Geophysical Abstracts 1 - 83 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey. Abstracts 112 and 113 were issued in mimeographed form by tine Bureau of Mines as Information Circulars 7256 and 7257. 1. GRAVITATIONAL METHODS 7004. Campbell, R. B. Florida&apos;s Geological Structure and Gravity. Proc. Florida Acad. Sciences for 1540, Gainesville, Fla., vol. 5, 1541, pp. 73-84.

Jan 1, 1943

By Edward D. Thimons

This Bureau of Mines report presents expected levels of air pollutants in the face areas of oil shale mines, based upon data collected by the authors and previous investigators. Ventilation requirements to maintain these pollutant levels below their threshold limit values and Federal and local mine air quality standards are discussed. Two practical face ventilation systems are discussed in terms of actual in-mine test experience.

Jan 1, 1986

By W. B. Berwald

The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gras association, has been studying actively for the past several years the problem of the flow of natural gas through high-pressure transmission lines. Numerous data on gas flow through pipe lines under many conditions of operation have been obtained by carefully conducted tests, and these data, together with all other available information, have been analyzed carefully to secure practical facts for the use of operators in designing pipe lines and determining the effects of different operating conditions on pipe-line capacities. The first procedure in initiating; this problem was to review, compile, and analyze all of the existing data on the flow of natural gas through pipe lines. Actual data applicable to pipe and operating conditions normally used in the transmission of natural gas were meager, and the several pipe line flow formulas developed by different investigators gave widely varying; results when applied to problems of pipe-line design. Therefore, further experimental work under conditions comparable to those found in transmitting natural gas was essential before any definite recommendations could be made.

Jan 1, 1931